1 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors iec appliance inlet c14 with fuseholder 1- or 2-pole and voltage selector fuse drawer must be ordered separately (see accessories). fuse drawer must be ordered separately (see accessories). see below: approvals and compliances c14 70 c description - panel mount : screw-on version from front or rear side, snap-in version from front side - 3 functions : appliance inlet protection class i , fuseholder with interchangeable fuse drawer for fuse-links 5x20 mm or 6.3x32 mm 1- or 2-pole , with or without voltage selector (step switch) - meets the requirements of iec 60335-1 for appliances in unattended use. this includes the enhanced requirements of glow wire tests acc. to iec 60695-2-12 and -13. - quick connect terminals 4.8 x 0.8 mm characteristics - available with or without internal connections - the fuse drawer "fingergrip" can be removed by hand - suitable for use in equipment according to iec/ul 60950 other versions on request - fuse drawer with other voltage values - for protection class ii - variant with notch for v-lock mating cordsets references alternative: version with line filter kfc weblinks pdf datasheet, html-datasheet, general product information, distributor- stock-check, accessories, detailed request for product, microsite newly available variants corresponding to v-lock mating cordset. the connector is equipped with a notch intended for use with the latching cordset. the cord latching system prevents against accidental removal of the cordset. technical data ratings iec 10 a / 250 vac; 50 hz ratings ul/csa 13 a / 125 vac; 60 hz 1? dielectric strength > 3 kvac between l-n > 4 kvac between l/n-pe (1 min/50 hz) allowable operation tempe - rature -25 c to 70 c ip-protection from front side ip 40 acc. to iec 60529 insulation cover suitable for appliances with protection class i acc. to iec 61140 terminal quick connect terminals 4.8 x 0.8 mm panel thickness s screw: max 8 mm mounting screw torque max 0.5 nm snap-in: 1.5/2/2.5 mm material: housing thermoplastic, black, ul 94v-0 appliance inlet/-outlet c14 acc. to iec 60320-1, ul 498, csa c22.2 no. 42 (for cold conditions) pin-temperature 70 c, 10 a, protection class i fuseholder 1 or 2 pole, shocksafe category pc2 acc. to iec 60127-6, for fuse-links 5 x 20 or 6.3 x 32 mm rated power acceptance @ ta 23 c 5 x 20: 2.5 w (1 pole)/ 2 w (2-pole) per pole 6.3 x 32: 3.15 w (1 pole)/ 2.5 w (2-pole) per pole power acceptance @ ta > 23c admissible power acceptance at higher ambient temperature see derating cur - ves voltage selector optional, step, 2-4 digits 1) ul/csa: 1-pole version 13 a, 2-pole version 10 a approvals and compliances detailed information on product approvals, code requirements, usage instructions and detailed test conditions can be looked up in details about approvals
2 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors approvals the approval mark is used by the testing authorities to certify compliance with the safety requirements placed on electronic products. approval reference type: KEC approval logo certificates certification body description vde approvals vde certificate number: 40046766 ul approvals ul ul file number: e93617 csa approvals csa csa certification record: 38456 cqc approvals cqc ccc certificate number: 2010010204409773 product standards product standards that are referenced organization design standard description designed according to iec 60320-1 appliance couplers for household and similar general purposes designed according to iec 60127-6 miniature fuses. part 6. fuse-holders for miniature fuse-links designed according to iec 61058-1 switches for appliances. part 1. general requirements designed according to ul 498 standard for attachment plugs and receptacles designed according to csa c22.2 no. 42 general use receptacles, attachment plugs, and similar wiring devices application standards application standards where the product can be used organization design standard description designed for applications acc. iec/ul 60950 iec 60950-1 includes the basic requirements for the safety of information technologyequipment. designed for applications acc. iec 60601-1 medical electrical equipment - part 1: general requirements for basic safety and essential performance designed for applications acc. iec 60335-1 safety of electrical appliances for household and similar purposes. meets the requirements for appliances in unattended use. this includes the en - hanced requirements of glow wire tests acc. to iec 60695-2-12 and -13. compliances the product complies with following guide lines identification details initiator description ce declaration of conformity schurter ag the ce marking declares that the product complies with the applicable requirements laid down in the harmonisation of community legislation on its affixing in accordance with eu regulation 765/2008. rohs schurter ag eu directive rohs 2011/65/eu china rohs schurter ag the law sj / t 11363-2006 (china rohs) has been in force since 1 march 2007. it is similar to the eu directive rohs. reach schurter ag on 1 june 2007, regulation (ec) no 1907/2006 on the registration, evaluation, authorization and restriction of chemicals 1 (abbreviated as "reach") entered into force. micrositev-lock schurter ag v-lock system are based on a matching plug-dose combination. the connector is equipped with a notch intended for use with the latching cordset. the cord latching system prevents against accidental removal of the cordset. medical equipment schurter ag suitable for use in medical equipment according to iec/ul 60601-1
3 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors dimensions [mm] screw-on mounting 40.7 50 30 55 4.8x0.8 r 4.5 r 6 r 3.1 41.1 + _ 0.1 0.15 58.3 18 27.7 27.3 ? 3.2 ? 6.3x90 27.6 + _ 0.1 r 3 0 -0.2 50 230 2.25 2 m3/? 3.6 snap-in mounting 40.7 30 55 4.8x0.8 r 4.5 r 3.1 41.1 18 27.7 27.3 27.6 r 3 0 -0.2 43.5 230 2.25 2 s 0.1 + _ 0.1 + _ 0.1 + _ 0.1
4 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors diagrams without internal connections voltage selector 4-positions, 1-pole 4 32 1 e ln a without internal connections voltage selector 4-positions, 2-pole 4 32 15 e ln ab with internal connections voltage selector 4-positions, 1-pole 4 32 1 e ln with internal connections voltage selector 4-positions, 2-pole 4 32 15 e ln voltage selector 3-positions 1-pole 32 1 voltage selector 3-positions 2-pole 32 1 5 voltage selector 2-positions 1-pole 31 voltage selector 2-positions 2-pole 31 5 without voltage selector 1-pole 2 without voltage selector 2-pole 25
5 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors derating curves fuses 5 x 20 mm (1-pole) admissible power acceptance in watt 1.5 1.0 0.5 0.0 2.5 2.0 02 04 06 08 0 100 i = << i n i = 0.7 i n i = 1.0 i n ambient air temperature t a c fuses 5 x 20 mm (2-pole, per pole) admissible power acceptance in watt per pole 02 04 06 08 0 100 i = << i n i = 0.7 i n i = 1.0 i n 2.0 1.5 1.0 0.5 0.0 ambient air temperature t a c fuses 6.3 x 32 mm (1-pole) admissible power acceptance in watt 02 04 06 08 01 00 1.5 1.0 0.5 0.0 2.5 3.15 2.0 i = << i n i = 0.7 i n i = 1.0 i n ambient air temperature t a c fuses 6.3 x 32 mm (2-pole, per pole) admissible power acceptance in watt per pole 1.5 1.0 0.5 0.0 2.5 2.0 02 04 06 08 0 100 i = << i n i = 0.7 i n i = 1.0 i n ambient air temperature t a c all variants panel mounting panel thickness s [mm] fuseholder voltage selector internally wired v-lock order number snap-in 1.5 1-pole - l 4303.0032 snap-in 1.5 1-pole 3/4 digits l 4303.0092 snap-in 1.5 1-pole 2 pos. l 4303.0212 snap-in 2 1-pole - l 4303.0033 snap-in 2 1-pole 3/4 digits l 4303.0093 snap-in 2 1-pole 2 pos. l 4303.0213 snap-in 2.5 1-pole - l 4303.0034 snap-in 2.5 1-pole 3/4 digits l 4303.0094 snap-in 2.5 1-pole 2 pos. l 4303.0214 snap-in 1.5 1-pole - 4303.1032 snap-in 1.5 1-pole 3/4 digits 4303.1092 snap-in 1.5 1-pole 2 pos. 4303.1212 snap-in 2 1-pole - 4303.1033 snap-in 2 1-pole 3/4 digits 4303.1093 snap-in 2 1-pole 2 pos. 4303.1213 snap-in 2.5 1-pole - 4303.1034 snap-in 2.5 1-pole 3/4 digits 4303.1094 snap-in 2.5 1-pole 2 pos. 4303.1214 snap-in 1.5 2-pole - l 4303.0002 snap-in 1.5 2-pole 3/4 digits l 4303.0062 snap-in 1.5 2-pole 2 pos. l 4303.0182
6 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors panel mounting panel thickness s [mm] fuseholder voltage selector internally wired v-lock order number snap-in 2 2-pole - l 4303.0003 snap-in 2 2-pole 3/4 digits l 4303.0063 snap-in 2 2-pole 2 pos. l 4303.0183 snap-in 2.5 2-pole - l 4303.0004 snap-in 2.5 2-pole 3/4 digits l 4303.0064 snap-in 2.5 2-pole 2 pos. l 4303.0184 snap-in 1.5 2-pole - 4303.1002 snap-in 1.5 2-pole 3/4 digits 4303.1062 snap-in 1.5 2-pole 2 pos. 4303.1182 snap-in 2 2-pole - 4303.1003 snap-in 2 2-pole 3/4 digits 4303.1063 snap-in 2 2-pole 2 pos. 4303.1183 snap-in 2.5 2-pole - 4303.1004 snap-in 2.5 2-pole 3/4 digits 4303.1064 snap-in 2.5 2-pole 2 pos. 4303.1184 screw - 1-pole - l 4303.0031 screw - 1-pole 3/4 digits l 4303.0091 screw - 1-pole 2 pos. l 4303.0211 screw - 1-pole - 4303.1031 screw - 1-pole 3/4 digits 4303.1091 screw - 1-pole 2 pos. 4303.1211 screw - 2-pole - l 4303.0001 screw - 2-pole 3/4 digits l 4303.0061 screw - 2-pole 2 pos. l 4303.0181 screw - 2-pole - 4303.1001 screw - 2-pole 3/4 digits 4303.1061 screw - 2-pole 2 pos. 4303.1181 most popular. availability for all products can be searched real-time: https://www.schurter.com/en/stock-check/stock-check-schurter packaging unit 50 pcs required accessory description fusedrawer 3 fusedrawer for fuse links 5x20 mm resp. 6.3x32 mm fingergrip, 5 x 20, 2-pole, voltage selector 4303.2014.00 fingergrip, 5 x 20, 2-pole, voltage selector, 100, 120, 220, 240 4303.2014.01 fingergrip, 5 x 20, 2-pole, voltage selector, 110, 150, 220 4303.2014.02 fingergrip, 5 x 20, 2-pole, voltage selector, 110, 220 4303.2014.03 ...
7 power entry modules without line filter KEC https://www.schurter.com /pg05 connectors accessories assorted covers rear cover 0859.0072 cord retaining kits cord retaining strain relief flat head, a 4700.0001 mating outlets/connectors category / description appliance outlet overview complete iec appliance outlet f, screw-on mounting, front side, solder terminal 4787 iec appliance outlet f, snap-in mounting, front side, solder or quick-connect terminal 4788 iec appliance outlet f or h, screw-on mounting, front side, solder, pcb or quick-connect terminal 5091 appliance outlet further types to KEC connector overview complete 4782 mounting: power cord, 3 x 1 mm2 / 3 x 18 awg, cable, connector: iec c13 4782 4022 mounting: power supply cord, 3 x 1.5 mm2, screw clamps, connector: iec c13 4022 4785 mounting: power cord, 3 x 1 mm2 / 3 x 18 awg, cable, connector: iec c13 4785 4300-06 mounting: power cord, 3 x 1 mm2 / 3 x 18 awg, cable, connector: iec c13 4300-06 4012 mounting: power supply cord, 3 x 1.5 mm2, screw clamps, connector: iec c13 4012 connector further types to KEC ... mating outlets/connectors shuttered power cord overview complete vac13ks, overview, diverse connector iec c13, cord end: vac13ks power cord with iec connector c17, v-lock, straight vac17ks power cord further types to KEC the specifications, descriptions and illustrations indicated in this document are based on current information. all content is subject to modifications and amendments. information furnished is believed to be accurate and reliable. however, users should independently evaluate the suitability and test each product selected for their own applications. 22.01.2018
|
