intelligent mp series up to 1500 watts total power: up to 1500 w input voltage: 85 - 264 vac 88 - 300 vdc # of outputs: up to 24 special features ? full medical en60601 approval ? intelligent i 2 c control ? voltage adjustment on all outputs (manual or i 2 c) ? confgurable input and output ok signals and indicators ? confgurable inhibit/enable ? confgurable output up/down sequencing ? confgurable current limit (foldback or constant current) ? high power density (8.8 w/cu-in) ? intelligent fan (speed control/fault status) ? downloadable gui from website ? customer provided air option ? up controlled pfc input with active inrush protection ? i 2 c monitor of voltage, current, and temp ? programmable voltage, current limit, inhibit/enable through i 2 c ? optional extended hold-up module (semi f47 compliance) ? increased power density to 50% over standard mp ? external switching frequency sync input ? optional conformal coating ? industrial temp range (-40 oc to 70 oc) ? no preload required ? industrial shock/vibration (> 50gs) safety ? ul ul60950/ul2601** ? csa csa22.2 no. 234 level 5 ? uv en60950/en60601-1** ? babt compliance to en60950/ en60601 bs7002 ? cb certifcate and report ? ce mark to lvd data sheet electrical specifcations input input ra nge 85 - 264 vac 88 - 300 vdc (limited to 300 vdc in medical applications) frequency 47 - 440 hz inrush current 40 a peak maximum (soft start) effciency up to 85% @ full case load power factor 0.99 typ. meets en61000-3-2 (n/a @ 440 hz) turn-on time ac on 2.0 sec typ., inhibit/enable 150 ms typical programmable delay; 50 ms internal turn-on delay (dual output only) emi flter cispr 22/en55022 level b** leakage current 300 a max. @ 240 vac; 47 - 63 hz radiated emi cispr 22/en55022 level b** holdover storage 20 ms minimum (independent of input vac) additional 34 ms holdover storage with optional hup module (semi f47 compatible). for imp4 15 ms (low-line), 10 ms (high-line) ac ok > 5 ms early warning min. before outputs lose regulation full cycle ride thru (50 hz) (n/a on imp4 > 750 w @ 90 vac) harmonic distortion meets en61000-3-2 isolation meets en60950 and en60601 input to output, input to ground: 2000 vac; output to ground: 400 vdc global inhibit / enable ttl, logic 1 and logic 0; confgurable input fuse (internal) imp4: 16 a; imp8: 20 a; imp1: 25 a (both lines fused) warranty 2 years power
electrical specifcations environmental specifcations operating temperature -40 to 70 c ambient. derate each output 2.5% per degree from 50 to 70 c. (-20 c start up) storage temperature -40 c to +85 c electromagnetic susceptibility designed to meet en61000-4; -2, -3, -4, -5, -6, -8, -11 level 3 humidity operating; non-condensing 10% to 95% rh vibratio iec68-2-6 to the levels of iec721-3-2 mtbf demonstrated > 550,000 hours at full load, 220 vac and 25 c ambient conditions output module line-up module code 1 2 3 5 4 module type single single single single dual triple max output power 210 w 360 w 750 w 1500 w 144 w 36 w max output current 35 a 60 a 150 a 140 a 10 a 2 a output voltages available* 2 - 60 v 2 - 60 v 2 - 60 v 6 - 60 v 8 - 15*, 24 - 28; 8 - 15*, 8 - 15*; 8 - 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28, 24 - 28; 24 - 28, 2 - 6 8-15, 8-15, 2-6; 8-15, 8-15, 8-15; 8-15, 8-15, 18-28; 8-15, 18-28, 2-6 standard voltage increments 25 25 25 18 16 18 remote sense yes yes yes yes yes yes no remote margin yes yes yes yes no no no v-program - i 2 c control yes yes yes yes yes yes no active current share yes yes yes yes yes no no module inhibit - i 2 c control yes yes yes yes yes yes yes module inhibit - analog yes yes yes yes yes no no overvoltage/overcurrent protection yes yes yes yes yes yes yes minimum load required no no no no no no no slots occupied in any ivs case 1 2 3 4 1 1 * note: contact factory for extended range down to 6 v output adjustment range* 10% minimum all outputs (manual) (full module adjustment range using i 2 c) factory set point accuracy 1% i 2 c output program accuracy 5% margining 4 - 6% nominal analog (single output module only) overall regulation 0.4% or 20 mv max. (1500 w modules 1% max.) (36 w modules 4% maximum) ripple rms: 0.1% or 10 mv, whichever is greater pk-pk: 1.0% or 50 mv, whichever is greater bandwidth limited to 20 mhz dynamic response < 2% or 100 mv, with 25% load step recovery time to within 1% in < 300 sec overcurrent protection** confgurable through i 2 c (calibration required). single output module and main output of the dual output module 105 - 120% of rated output current. aux output of dual output module 105 - 140% of rated output current short-circuit protection: protected for continuous short-circuit. recovery is automatic upon removal of short overvoltage protection* confgurable through i 2 c single output module: 2 - 5.5 v 122 - 134%; 6 - 60 v 110 - 120% dual output module: 2 - 6 v 122 - 134%; 8 - 28 v 110 - 120% triple output module: 110 - 120% of highest voltage rating output (cont.) reverse voltage protection: 100% of rated output current thermal protection* (otp and otw) confgurable through i 2 c all outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (ac ok signal) before shutdown remote sense up to 0.5 v total drop (not available on triple output module) single wire parallel current share to within 2% of total rated current dc ok* 5% of nominal. confgurable through i 2 c minimum load not required housekeeping bias voltage 5 vdc @ 1.0 a max. present whenever ac input is applied (optional 2.0 a available) module inhibit* confgured and controlled through i 2 c switching frequency 250k hz accepts external sync signal output/output isolation > 1 megohm, 500 v external sync ttl clock input signal used to adjust switching frequency. frequency 500 khz 20%; duty cycle 40 - 55% * can be controlled via i 2 c ** controlled via i 2 c but requires load calibration i mp data sheet
ordering information ordering notes: 1. the cases and modules of both mp and imp series can be interchanged to allow more fexibility. if intelligent modules are used with non-intelligent cases, a numeric code 4 is placed at the end of the module code (ex. 4ll0 becomes 4ll4). 2. usb to i 2 c module order code 73-769-001 7 6 5 4 3 2 1 i mp4 available slots i mp8 available slots slot 1 slot 2 slot 3 slot 4 slot 5 slot 1 slot 2 slot 3 slot 4 slot 5 slot 6 slot 2 slot 3 slot 4 slot 6 slot 7 slot 5 i mp1 available slots parallel codes 0 = no parallel 1 = 1 & 2 2 = 2 & 3 3 = 3 & 4 4 = 4 & 5 5 = 3 & 4 & 5 6 = 5 & 6 7 = 4 & 5 & 6 8 = 6 & 7 9 = 3 & 4, 6 & 7 a = 1 & 2, 3 & 4, 5 & 6 c = 2 & 3, 4 & 5 e = 3 & 4, 5 & 6 f = 2 & 3, 4 & 5, 6 & 7 i mp 1* - 3l0 - 2e2 - 1q1 - 4ll0 - 00 - a - ### case size (mm) 4 = 2.5 x 5 x 10; 750 w - 1158 w, 5 slots (63.5 x 127 x 254 mm) 8 = 2.5 x 7 x 10; 1000 w - 1200 w, 6 slots (63.5 x 177.8 x 254 mm) 1 = 2.5 x 8 x 11; 1200 w - 1500 w, 7 slots (63.5 x 203.2 x 279.4 mm) module codes module/voltage/option codes module codes: (none) = 36 w triple o/p (1 slot) 1 = 210 w single o/p (1 slot) 2 = 360 w single o/p (2 slot) 3 = 750 w single o/p (3 slot) 4 = 144 w dual o/p (1 slot) 5 = 1500 w single o/p (4 slot) 6 - 9 = future case option codes first digit 0 - 9, a - z parallel code (see parallel codes table above) second digit 0 = no options 1 = reverse air 3 = global enable 4 = fan idle with inhibit 5 = opt 1 + opt 3 6 = opt 1 + opt 4 7 = opt 3 + opt 4 8 = opt 1 +3 +4 9 = rs485 73-544-002 c = opt 3 + opt 9 d = can bus 73-544-003 e = opt 3 + opt d software code voltage codes: see output module voltage/current table above option codes: 0 = standard 1 = module enable 2 = constant current 3 = 1 & 2 combined 4 = set for use in standard (non-intelligent case) 5 = shutdown mode for 1500 w 6 = 1 & 5 combined 7 - 9 = future module/voltage/option codes first - module code second - voltage code third - option code case option codes case size factory assembled for hardware of firmware mods. hardware code * note: add e after imp4 to denote iec input option. e.g. imp4e (not available on imp8 or imp1) software code used for configuration change. a is standard output module voltage/current* voltage voltage code single output module code dual output*** triple output i 2 c adjustment ranges**** 1 2 3 5 4 4 - - - 2 v a 35 a 60 a 150 a 300 a 10 a 10 a 2 a 1.8 - 2.2 2.2 v b 35 a 60 a 150 a 300 a 10 a 10 a 2 a 2.0 - 2.4 3 v c 35 a 60 a 150 a 300 a 10 a 10 a 2 a 2.7 - 3.3 3.3 v d 35 a 60 a 150 a 300 a 10 a 10 a 2 a 3.0 - 3.6 5 v e 35 a 60 a 150 a 300 a 10 a 10 a 2 a 4.5 - 5.5 5.2 v f 35 a 60 a 144 a 288 a 10 a 10 a 2 a 4.7 - 5.7 5.5 v g 34 a 58 a 136 a 273 a 10 a 10 a 2 a 5.0 - 6.1 6.0 v h 23 a 42 a 97.5 a 250 a 10 a* 10 a* 2 a 5.4 - 6.6 8.0 v i 20 a 36 a 84.4 a 187.5 a 10 a 4 a 1 a 1 a 1 a 7.2 - 8.8 10 v j 18 a 32 a 75 a 140 a 10 a 4 a 1 a 1 a 1 a 9.0 - 11.0 11 v k 17 a 31 a 68 a 136.3 a 10 a 4 a 1 a 1 a 1 a 9.9 - 12.1 12 v l 17 a 30 a 62.5 a 125 a 10 a 4 a 1 a 1 a 1 a 10.8 - 13.2 14 v m 14 a 21 a 53.5 a 107 a 9 a 4 a 1 a 1 a 1 a 12.6 - 15.4 15 v n 14 a 20 a 50 a 100 a 8 a 4 a 1 a 1 a 1 a 13.5 - 16.5 18 v o 11 a 19 a 41.6 a 83.3 a 0.5 a 0.5 a 16.2 - 19.8 20 v p 10.5 a 18 a 37.5 a 75 a 0.5 a 0.5 a 18.0 - 22.0 24 v q 8.5 a 15 a 30 a 62.5 a 4 a 2 a 0.5 a 0.5 a 21.6 - 26.4 28 v r 6.7 a 11 a 26.8 a 53.5 a 3 a 2 a 0.5 a 0.5 a 25.2 - 30.8 30 v s 6.5 a 11 a 25 a 50 a 27.0 - 33.0 33 v t 6.2 a 10.9 a 22.7 a 35.8 a 29.7 - 36.3 36 v u 5.8 a 10 a 20.8 a 35.8 a 32.4 - 39.6 42 v v 4.2 a 7.5 a 16 a 35.7 a 37.8 - 46.2 48 v w 4.0 a 7.5 a 15.6 a 31.2 a 43.2 - 52.8 54 v x 3.7 a 6.0 a 13.9 a 27.7 a 48.6 - 59.4 60 v y 3.5 a 6.0 a 12.5 a 25 a 54.0 - 66.0 contact factory special* z 35 a 60 a 150 a 300 a 10 a 2.3 - 2.6 special* z 35 a 60 a 150 a 300 a 10 a 3.7 - 4.4 special* z 20 a 36 a 80 a 140 a 8 a 6.7 - 7.1 * note: contact factory for extended range down to 6 v. ** increments of current not shown can be achieved by paralleling modules (add currents of each module selected). *** total output power on dual model must not exceed 144 w. **** for single output modules only. i mp data sheet
i mp4 (ac input on opposite side) i mp8 and i mp1 210 w 360 w 750 w 1500 w ( 10 - 60 v) 144 w 36 w pin connectors ac input pin no. function 1 ac neutral 2 ac line (hot) 3 chassis (earth) ground pfc input connector (control and signals) pin no. function 1 input ac ok - emitter 2 input ac ok - collector 3 global dc ok - emitter 4 global dc ok - collector 5 external sync 6 global inhibit/optional enable logic 0 7 global inhibit/optional enable logic 1 8 global inhibit/optional enable return 9 +5 vsb housekeeping 10 +5 vsb housekeeping return i 2 c bus output connector pin no. function 1 no connection 2 no connection 3 no connection 4 serial clock signal (scl) 5 serial data signal (sda) 6 address bit 0 (a0) 7 address bit 1 (a1) 8 address bit 2 (a2) 9 secondary return (gnd) 10 5 vcc external bus (5 vcc. bus) single dual triple input 85 - 264 vac 180 - 264 vac i mp 8 = 2.5 x 7 x 10 6 available slots 1000 w max. 1200 w max. (63.5 x 177.8 x 254 mm) i mp 1 = 2.5 x 8 x 11 7 available slots 1200 w max. 1500 w max. (63.5 x 203.2 x 279.4 mm) s l o t 7 s l o t 5 s l o t 6 s l o t 4 s l o t 3 s l o t 2 s l o t 1 -a- s l o t s l o t s l o t s l o t s l o t 5 4 32 1 i mp 1 only mates with molex 90142-0010 housing 90119-2110 pin connector kit part no.: 70-841-004 mates with landwin 2050s1000 housing 2053t011v pin or jst phdr-10vs housing jst sphd-002t-p0.5 (28-24) jst sphd-001t-p0.5 (26-22) connector kit part no.: 70-841-023 figure 1. ac input figure 2. connector j1 figure 3. connector j2 input 90 - 264 vac 180 - 264 vac i mp 4 = 2.5 x 5 x 10 5 available slots 750 w max. 1158 w max. (63.5 x 127 x 254 mm) 10 6 5 1 1 2 3 ~ n 10 5 1500 w with bus bar adapter option (used with the 10 - 60 v module) 1500 w ( 2.0 - 8.0 v) i mp data sheet
mechanical drawings .6 3? ( 1 6.0) .3 2? ( 8 .1) 1.38 ? (35.2 ) ( 2 x) . 44? (11.4) .48? (12.1) ( 2 x) .33? ( 8 . 5) v adj v- v+ m 4 x 8 screws with conical w asher dc output connector pin 1 .44" (11.4) .32" (8.1) 1.38" (35.1) .48" (12.1) .44? (11.2 ) 2x v+ m4x8 screws with conical w asher dc output connector pin 1 v- v adj pin 1 v2 adj .32 (8.1) .42 (10.7) v1 + v1 - v2 + m3x8 screws with spring w asher (4x) .46 (11.7) (4x) .30 (7.5) (3x) v1 adj 1.17 (29.7) v2 - dual 144 watt single 360 watt single 1500 watt 8 - 60 v single 750 watt triple 36 watt .32" (8.1) .44" (11.0 ) 1.24"(31.5) (2x) .61"(15.6) (2x) .59" (15.0) .63" (16.0) dc output connector pin 1 v adj m4x8 screws (4x) v- v+ v1 + v1 - v2 - v3 - v3 + v 2 + v- v+ 59.3 0.2 (2x) 15.0 0.8 (2x) 16.0 0.2 (2x) 16.0 0.2 (3x) 31.6 0.8 11.3 0.8 8.1 0.8 dc output connector pin 1 m4x8 screws w/ conical w asher (6x) for factory-use only v adj single 210 watt i mp modules dc-dc converter output modules mates with molex 90142-0010 housing 90119-2110 pin mates with molex 09-91-0600 housing 26-60-5060 pin figure 4. connector j1 control signal information, j1 control connector pin no. function 1 + remote sense single or dual o/p main 2 remote margin / v. program single o/p 3 margin high single o/p 4 - remote sense / margin low single or dual o/p main 5 spare 6 module, isolated inhibit single or dual o/p 7 module inhibit return single or dual o/p 8 current share (swp) single or dual o/p main 9 + remote sense v2 dual o/p, single is spare 10 - remote sense v2 dual o/p, single is spare * note: all imp modules have a green dcok led. (except for 36 w module) figure 1. ac in put 1 2 3 ~ n 6 1 10 5 figure 2. connector j1 v1 adj v2 adj v3 adj v1+ v3+ v1- v2+ v2- v3- i mp data sheet
i mp series i mp4 (750/1158 watts max) 5-inch case size: imp4: 2.5 x 5 x 10 (63.5 mm x 127 mm x 254 mm) weight: imp4 case: 3 lbs. ? 360 w single 1.0 lb. ? 750 w single: 1.6 lbs. 144 w dual: 0.6 lb. notes: 1. input: barrier type. three no. 6-32 b.h. screws (0.375 centers). max torque: 6 in-lbs. (0.67 n-m). (optional iec input connector) 2. control connectors: (j1) 10 position housing, gold plated contacts. mates with molex 90142-0010 housing with 90119-2110 crimp contacts (molex c - grid iii series). connector kit includes mating connector and 10 pins, astec part #70-841-004. (j2) 10 position housing (landwin 2051p1000t). mates with housing 2050s1000 (landwin) with 2053t011p (landwin) pins or jst phdr-iovs housing and jst sphd-002t-po.5 pins. 3. chassis material: aluminum with chemical flm coating (conductive). 4. all dimensions are in millimeters and inches, and are typical. 5. customer mounting -3 sides m4, bottom also includes 8-32 mounting holes. max. penetration is 0.150 (3.8 mm). max. torque: 5 in-lbs. (0.57 n-m). 6. output module connections: all single o/p modules are m4 x 8 mm screws. max. torque: 10 in-lbs. (1.13 n-m). dual o/p module is m3 x 8 mm screws. max. torque: 5 in-lbs. (0.57 n-m). i mp data sheet
i mp series i mp8 (1000/1200 watts max) 7-inch case size: imp8: 2.5 x 7 x 10 (63.5 mm x 177.8 mm x 254 mm) weight: imp8 case: 4.1 lbs. ? 210 w single: 0.6 lb. ? 360 w single: 1.0 lb. ? 750 w single: 1.6 lbs. 144 w dual: 0.6 lb. notes: 1. input: barrier type. three no. 6-32 b.h. screws (0.375 centers). max torque: 6 in-lbs. (0.67 n-m). 2. control connectors: (j1) 10 position housing, gold plated contacts. mates with molex 90142-0010 housing with 90119-2110 crimp contacts (molex c - grid iii series) connector kit includes mating connector and 10 pins, astec part #70-841-004. (j2) 10 position housing (landwin 2051p1000t). mates with housing 2050s1000 (landwin) with 2053t011p (landwin) pins or jst phdr-iovs housing and jst sphd-002t-po.5 pins. 3. chassis material: aluminum with chemical flm coating (conductive). 4. all dimensions are in millimeters and inches, and are typical. 5. customer mounting -3 sides m4, bottom also includes 8-32 mounting holes. max. penetration is 0.150 (3.8 mm). max. torque: 5 in-lbs. (0.57 n-m). 6. output module connections: all single o/p modules are m4 x 8 mm screws. max. torque: 10 in-lbs. (1.13 n-m). dual o/p module is m3 x 8 mm screws. max. torque: 5 in-lbs. (0.57 n-m). x y xx x y y y 171.45 171.45 177.8 19.05 m4 mounting holes (4x) marked as x #8-32 mounting holes (4x) marked as y m4 mounting holes (4x) identical both sides 38.10 normal air flow reverse air flow i mp data sheet
i mp series i mp1 (1200/1500 watts max) 8-inch case size: imp1: 2.5 x 8 x 11 (63.5 mm x 203.2 mm x 279.4 mm) weight: imp1 case: 5.0 lb. ? 210 w single: 0.6 lb. ? 360 w single: 1.0 lb. ? 750 w single: 1.6 lb. ? 144 w dual: 0.6 lb. notes: 1. input: barrier type. three no. 6-32 b.h. screws (0.375 centers). max torque: 6 in-lbs (0.67 n-m). 2. control connectors: (j1) 10 position housing, gold plated contacts. mates with molex 90142-0010 housing with 90119-2110 crimp contacts (molex c - grid iii series). connector kit includes mating connector and 10 pins, astec part #70-841-004. (j2) 10 position housing (landwin 2051p1000t). mates with housing 2050s1000 (landwin) with 2053t011p (landwin) pins or jst phdr-iovs housing and jst sphd-002t-po.5 pins. 3. chassis material: aluminum with chemical flm coating (conductive). 4. all dimensions are in millimeters and inches, and are typical. 5. customer mounting -3 sides m4, bottom also includes 8-32 mounting holes. max. penetration is 0.150 (3.8 mm). max. torque: 5 in-lbs. (0.57 n-m). 6. output module connections: all single o/p modules are m4 x 8 mm screws. max. torque: 10 in-lbs. (1.13 n-m). dual o/p module is m3 x 8 mm screws. max. torque: 5 in-lbs. (0.57 n-m). x y xx x y y y 171.45 171.45 177.8 19.05 m4 mounting holes (4x) marked as x #8-32 mounting holes (4x) marked as y m4 mounting holes (4x) identical both sides 38.10 normal air flow reverse air flow i mp data sheet
imp ds 14aug2015 the rs485/can-to-i 2 c uses 2 input protocols and 1 output protocol. the input protocols used are rs485 using modbus (command index: 0x01), and can using modifed modus (command index: 0x02). the output protocol use is: i 2 c with smbus support (command index: 0x80). master/client device(s) adapter output protocols slave/server device(s) adapter protocol input protocols ada p ter command rs485 using modbus ada p ter controls ca n using modi ed modbus i 2 c with smbus support i mp can rs485 optional canbus or rs485 interface rs485/can - to - i 2 c for detailed info, download the software requirements specifcation (srs) from http://www.artesyn.com/power/power- supplies/cat/101/confgurable-power-supplies-imp-series worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com www.artesyn.com i mp data sheet while every precaution has been taken to ensure accuracy and completeness in this literature, artesyn embedded technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2015 artesyn embedded technologies, inc.
|
