![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
? 2010-2011 microchip technology inc. ds22243d-page 1 mcp6h01/2/4 features: input offset voltage: 0.7 mv (typical) quiescent current: 135 a (typical) common mode rejection ratio: 100 db (typical) power supply rejection ratio: 102 db (typical) rail-to-rail output supply voltage range: - single-supply operation: 3.5v to 16v - dual-supply operation: 1.75v to 8v gain bandwidth product: 1.2 mhz (typical) slew rate: 0.8v/s (typical) unity gain stable extended temperature range: -40c to +125c no phase reversal applications: automotive power electronics industrial control equipment battery powered systems medical diagnostic instruments design aids: spice macro models filterlab ? software maps (microchip advanced part selector) analog demonstration and evaluation boards application notes typical application description: microchips mcp6h01/2/4 family of operational amplifi- ers (op amps) has a wide supply voltage range of 3.5v to 16v and rail-to-rail output operation. this family is unity gain stable and has a gain bandwidth product of 1.2 mhz (typical). these devices operate with a single-supply voltage as high as 16v, while only drawing 135 a/amplifier (typical) of quiescent current. the mcp6h01/2/4 family is offered in single (mcp6h01), dual (mcp6h02) and quad (mcp6h04) configurations. all devices are fully specified in extended temperature range from -40c to +125c. package types difference amplifier r 1 v out r 2 r 1 v ref r 2 v dd v 1 v 2 mcp6h01 * includes exposed thermal pad (ep); see ta b le 3 -1 . 1 2 3 4 8 7 6 5 ep 9 v dd v out nc nc v in + v in C v ss nc 1 2 3 4 8 7 6 5 ep 9 v outb v inb C v inb + v dd v ina + v ina C v ss v outa v ina + v ina C v ss 1 2 3 4 8 7 6 5 v outa v dd v outb v inb C v inb + v in + v in C v ss 1 2 3 4 8 7 6 5 nc ncv dd v out nc mcp6h01 soic mcp6h02 soic mcp6h01 2x3 tdfn mcp6h02 2x3 tdfn mcp6h04 soic, tssop v ina + v ina C v dd 1 2 3 4 14 13 12 11 v outa v outd v ind C v ind + v ss v inb + 5 10 v inc + v inb C 6 9 v outb 7 8 v outc v inc C v in + v in C 1 2 3 5 4 v dd v out mcp6h01 sc70-5, sot 23-5 v ss 1.2 mhz, 16v op amps downloaded from: http:///
mcp6h01/2/4 ds22243d-page 2 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 3 mcp6h01/2/4 1.0 electrical characteristics 1.1 absolute maximum ratings ? v dd C v ss ..........................................................................17v current at input pins............................................. .........2 ma analog inputs (v in +, v in -)??.............v ss C 1.0v to v dd +1.0v all other inputs and outputs ............v ss C 0.3v to v dd +0.3v difference input voltage.......................................... v dd C v ss output short-circuit current...................................continuous current at output and supply pins ..............................65 ma storage temperature.....................................-65c to +15 0c maximum junction temperature (t j )...........................+150c esd protection on all pins (hbm; mm) ???????????????????? 2 kv; 200v ? notice: stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listi ngs of this specification is not implied. exposure to maximum rating conditions for extended periods may affect device reliability. ?? see 4.1.2 input voltage limits . dc electrical specifications electrical characteristics : unless otherwise indicated, v dd = +3.5v to +16v, v ss = gnd, t a = +25c, v cm =v dd /2 C 1.4v, v out ? v dd /2, v l =v dd /2 and r l =10k ?? to v l . (refer to figure 1-1 ). parameters sym min typ max units conditions input offset input offset voltage v os -3.5 0.7 +3.5 mv input offset drift with temperature ? v os / ? t a 2 . 5 v / c t a = -40c to +125c power supply rejection ratio psrr 87 102 db input bias current and impedance input bias current i b 1 0p a i b 6 0 0p at a = +85c i b 1 02 5n a t a = +125c input offset current i os 1p a common mode input impedance z cm 1 0 13 ||6 ? ||pf differential input impedance z diff 1 0 13 ||6 ? ||pf common mode common mode input voltage range v cmr v ss ? 0.3 v dd ? 2.3 v common mode rejection ratio cmrr 78 93 db v cm = -0.3v to 1.2v, v dd =3.5v 82 98 db v cm = -0.3v to 2.7v, v dd =5v 84 100 db v cm = -0.3v to 12.7v, v dd =15v open-loop gain dc open-loop gain (large signal) a ol 95 115 db 0.2v < v out <(v dd C 0.2v) downloaded from: http:/// mcp6h01/2/4 ds22243d-page 4 ? 2010-2011 microchip technology inc. ac electrical specifications output high-level output voltage v oh 3.490 3.495 v v dd =3.5v 0.5v input overdrive 4.985 4.993 v v dd =5v 0.5v input overdrive 14.970 14.980 v v dd =15v 0.5v input overdrive low-level output voltage v ol 0.005 0.010 v v dd =3.5v 0.5 v input overdrive 0.007 0.015 v v dd =5v 0.5 v input overdrive 0.020 0.030 v v dd =15v 0.5 v input overdrive output short-circuit current i sc 2 7m a v dd =3.5v 4 5m a v dd =5v 5 0m a v dd =15v power supply supply voltage v dd 3.5 16 v single-supply operation 1.75 8 v dual-supply operation quiescent current per amplifier i q 125 175 a i o =0, v dd =3.5v v cm =v dd /4 130 180 a i o =0, v dd =5v v cm =v dd /4 135 185 a i o =0, v dd =15v v cm =v dd /4 electrical characteristics: unless otherwise indicated, t a = +25c, v dd = +3.5v to +16v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l = 60 pf. (refer to figure 1-1 ). parameters sym min typ max units conditions ac response gain bandwidth product gbwp 1.2 mhz phase margin pm 57 c g = +1v/v slew rate sr 0.8 v/s noise input noise voltage e ni 12 vp-p f = 0.1 hz to 10 hz input noise voltage density e ni 3 5n v / ? hz f = 1 khz 3 0n v / ? hz f = 10 khz input noise current density i ni 1 . 9f a / ? hz f = 1 khz dc electrical specifications (continued) electrical characteristics : unless otherwise indicated, v dd = +3.5v to +16v, v ss = gnd, t a = +25c, v cm =v dd /2 C 1.4v, v out ? v dd /2, v l =v dd /2 and r l =10k ?? to v l . (refer to figure 1-1 ). parameters sym min typ max units conditions downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 5 mcp6h01/2/4 temperature specifications 1.2 test circuits the circuit used for most dc and ac tests is shown in figure 1-1 . this circuit can independently set v cm and v out (refer to equation 1-1 ). note that v cm is not the circuits common mode voltage ((v p +v m )/2), and that v ost includes v os plus the effects (on the input offset error, v ost ) of temperature, cmrr, psrr and a ol . equation 1-1: figure 1-1: ac and dc test circuit for most specifications. electrical characteristics: unless otherwise indicated, v dd = +3.5v to +16v and v ss = gnd. parameters sym min typ max units conditions temperature ranges operating temperature range t a -40 +125 c note 1 storage temperature range t a -65 +150 c thermal package resistances thermal resistance, 5l-sc70 ? ja 3 3 1 c / w thermal resistance, 5l-sot-23 ? ja 2 5 6 c / w thermal resistance, 8l-2x3 tdfn ? ja 4 1 c / w thermal resistance, 8l-soic ? ja 149.5 c/w thermal resistance, 14l-soic ? ja 9 5 . 3 c / w thermal resistance, 14l-tssop ? ja 1 0 0 c / w note 1: the internal junction temperature (t j ) must not exceed the absolute maximum specification of +150c. g dm r f r g ? = v cm v p v dd 2 ? + ?? 2 ? = v out v dd 2 ? ?? v p v m ? ?? v ost 1 g dm + ?? ? ++ = where: g dm = differential mode gain (v/v) v cm = op amps common mode input voltage (v) v ost = op amps total input offset voltage (mv) v ost v in ? v in + ? = v dd r g r f v out v m c b2 c l r l v l c b1 100 k ? 100 k ? r g r f v dd /2 v p 100 k ? 100 k ? 60 pf 10 k ? 1f 100 nf v inC v in+ c f 6.8 pf c f 6.8 pf mcp6h0x downloaded from: http:/// mcp6h01/2/4 ds22243d-page 6 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 7 mcp6h01/2/4 2.0 typical performance curves note: unless otherwise indicated, t a =+25c, v dd = +3.5v to +16v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-1: input offset voltage. figure 2-2: input offset voltage drift. figure 2-3: input offset voltage vs. common mode input voltage. figure 2-4: input offset voltage vs. common mode input voltage. figure 2-5: input offset voltage vs. common mode input voltage. figure 2-6: input offset voltage vs. output voltage. note: the graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. the performance characteristics listed herein are not tested or guaranteed. in some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 0% 3% 6% 9% 12% 15% 18% 21% -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 input offset voltage (mv) percentage of occurences 2550 samples 0% 5% 10% 15% 20% 25% 30% 35% -16 -14 -12 -10 -8-6 -4 -2 02 4 6 8 1012 14 16 input offset voltage drift (v/c) percentage of occurences 2550 samples t a = - 40c to +125c -1000 -800 -600 -400 -200 0 200 400 600 800 1000 - 0 .50 .00 .51 .01 .52. 02 .5 common mode input voltage (v) input offset voltage (v) t a = +125c t a = +85c t a = +25c t a = -40c v dd = 3.5v representative part -1000 -800 -600 -400 -200 0 200 400 600 800 1000 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 common mode input voltage (v) input offset voltage (v) t a = +125c t a = +85c t a = +25c t a = -40c v dd = 5v representative part -1000 -800 -600 -400 -200 0 200 400 600 800 1000 -0.5 1.5 3.5 5.5 7.5 9.5 11.5 13.5 15.5 common mode input voltage (v) input offset voltage (v) t a = +125c t a = +85c t a = +25c t a = -40c v dd = 15v representative part -1000 -800 -600 -400 -200 0 200 400 600 800 1000 0 2 4 6 8 10121416 output voltage (v) input offset voltage (v) v dd = 15v v dd = 3.5v representative part v dd = 5v downloaded from: http:/// mcp6h01/2/4 ds22243d-page 8 ? 2010-2011 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +3.5v to +16v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-7: input offset voltage vs. power supply voltage. figure 2-8: input noise voltage density vs. frequency. figure 2-9: input noise voltage density vs. common mode input voltage. figure 2-10: cmrr, psrr vs. frequency. figure 2-11: cmrr, psrr vs. ambient temperature. figure 2-12: input bias, offset currents vs. ambient temperature. -1000 -800 -600 -400 -200 0 200 400 600 800 1000 024681012141618 power supply voltage (v) input offset voltage (v) t a = +125c t a = +85c t a = +25c t a = -40c representative part 10 100 1,000 1 10 100 1000 10000 100000 frequency (hz) input noise voltage density (nv/ ? ? hz) 1 10 100 1k 10k 100k 10 15 20 25 30 35 40 45 50 -113579111315 common mode input voltage (v) input noise voltage density (nv/ ? hz) f = 1 khz v dd = 16v 20 30 40 50 60 70 80 90 100 110 120 10 100 1000 10000 100000 1000000 frequency (hz) cmrr, psrr (db) 10 100 1k 10k 100k 1m cmrr psrr+ psrr- representative part 50 60 70 80 90 100 110 120 130 -50 -25 0 25 50 75 100 125 ambient temperature (c) cmrr, psrr (db) psrr cmrr @ v dd = 15v @ v dd = 5v @ v dd = 3.5v 1 10 100 1000 10000 100000 2535 45 55 65 75 85 95 105 115 125 ambient temperature (c) input bias and offset currents (a) input bias current input offset current v dd = 15v 100n 10n 1n 100p 10p 1p downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 9 mcp6h01/2/4 note: unless otherwise indicated, t a =+25c, v dd = +3.5v to +16v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-13: input bias current vs. common mode input voltage. figure 2-14: quiescent current vs. ambient temperature. figure 2-15: quiescent current vs. power supply voltage. figure 2-16: open-loop gain, phase vs. frequency. figure 2-17: dc open-loop gain vs. power supply voltage. figure 2-18: dc open-loop gain vs. output voltage headroom. 1 10 100 1000 10000 100000 0 2 4 6 8 10 12 14 16 common mode input voltage (v) input bias current (a) t a = +125c t a = +85c v dd = 15v 100n 10n 1n 100 p 10 p 1p 80 90 100 110 120 130 140 150 160 170 180 190 200 -50 -25 0 25 50 75 100 125 ambient temperature (c) quiescent current (a/amplifier) v dd = 15v v dd = 5v v dd = 3.5v 0 20 40 60 80 100 120 140 160 180 200 0 2 4 6 8 10121416 power supply voltage (v) quiescent current (a/amplifier) t a = +125c t a = +85c t a = +25c t a = -40c -20 0 20 40 60 80 100 120 1.0e-01 1.0e+00 1.0e+01 1.0e+02 1.0e+03 1.0e+04 1.0e+05 1.0e+06 1 .0e+07 frequency (hz) open-loop gain (db) -210 -180 -150 -120 -90 -60 -30 0 open-loop phase () open-loop gain open-loop phase 0.1 1 10 100 1k 10k 100k 1m 10m 80 90 100 110 120 130 140 150 160 3 5 7 9 11131517 power supply voltage (v) dc-open loop gain (db) v ss + 0.2v < v out < v dd - 0.2v 80 90 100 110 120 130 140 150 0.00 0.05 0.10 0.15 0.20 0.25 0.30 output voltage headroom (v) v dd - v oh or v ol - v ss dc-open loop gain (db) v dd = 15v v dd = 5v v dd = 3.5v downloaded from: http:/// mcp6h01/2/4 ds22243d-page 10 ? 2010-2011 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +3.5v to +16v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-19: channel-to-channel separation vs. frequency (mcp6h02 only). figure 2-20: gain bandwidth product, phase margin vs. ambient temperature. figure 2-21: gain bandwidth product, phase margin vs. ambient temperature. figure 2-22: output short circuit current vs. power supply voltage. figure 2-23: output voltage swing vs. frequency. figure 2-24: output voltage headroom vs. output current. 40 60 80 100 120 140 160 100 1000 10000 100000 frequency (hz) channel to channel separation (db) 100 1k 10k 100k input referred 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -50 -25 0 25 50 75 100 125 ambient temperature (c) gain bandwidth product (mhz) 0 20 40 60 80 100 120 140 160 180 phase margin () gain bandwidth product phase margin v dd = 3.5v 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -50 -25 0 25 50 75 100 125 ambient temperature (c) gain bandwidth product (mhz) 0 20 40 60 80 100 120 140 160 180 phase margin () gain bandwidth product phase margin v dd = 15v 0 10 20 30 40 50 60 70 0 2 4 6 8 10 12 14 16 power supply voltage (v) output short circuit current (ma) t a = +125c t a = +85c t a = +25c t a = -40c 0.1 1 10 100 100 1000 10000 100000 1000000 frequency (hz) output voltage swing (v p-p ) v dd = 3.5v v dd = 5v 100 1k 10k 100k 1m v dd = 15v 1 10 100 1000 10000 0.01 0.1 1 10 100 output current (ma) output voltage headroom (mv) v dd - v oh v ol - v ss v dd = 15v downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 11 mcp6h01/2/4 note: unless otherwise indicated, t a =+25c, v dd = +3.5v to +16v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-25: output voltage headroom vs. output current. figure 2-26: output voltage headroom vs. output current. figure 2-27: output voltage headroom vs. ambient temperature. figure 2-28: output voltage headroom vs. ambient temperature. figure 2-29: output voltage headroom vs. ambient temperature. figure 2-30: slew rate vs. ambient temperature. 0.1 1 10 100 1000 0.01 0.1 1 10 100 output current (ma) output voltage headroom (mv) v dd - v oh v ol - v ss v dd = 5v 0.1 1 10 100 1000 0.0 0.1 1.0 10.0 output current (ma) output voltage headroom (mv) v dd - v oh v ol - v ss v dd = 3.5v 15 16 17 18 19 20 21 22 -50 -25 0 25 50 75 100 125 ambient temperature (c) output voltage headroom (mv) v dd - v oh v ol - v ss v dd = 15v 2 3 4 5 6 7 8 -50 -25 0 25 50 75 100 125 ambient temperature (c) output voltage headroom (mv) v dd - v oh v ol - v ss v dd = 5v 2 3 4 5 6 7 8 -50-25 0 255075100125 ambient temperature (c) output voltage headroom (mv) v dd - v oh v ol - v ss v dd = 3.5v 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 -50 -25 0 25 50 75 100 125 ambient temperature (c) slew rate (v/s) falling edge, v dd = 15v rising edge, v dd = 15v downloaded from: http:/// mcp6h01/2/4 ds22243d-page 12 ? 2010-2011 microchip technology inc. note: unless otherwise indicated, t a =+25c, v dd = +3.5 v to +16 v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-31: slew rate vs. ambient temperature. figure 2-32: small signal non-inverting pulse response. figure 2-33: small signal inverting pulse response. figure 2-34: large signal non-inverting pulse response. figure 2-35: large signal inverting pulse response. figure 2-36: the mcp6h01/2/4 shows no phase reversal. 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 -50 -25 0 25 50 75 100 125 ambient temperature (c) slew rate (v/s) falling edge, v dd = 5v rising edge, v dd = 5v falling edge, v dd = 3.5v rising edge, v dd = 3.5v time (2 s/div) output voltage (20 mv/div) v dd = 15v g = +1v/v time (2 s/div) output voltage (20 mv/div) v dd = 15v g = -1v/v 0 2 4 6 8 10 12 14 16 time (20 s/div) output voltage (v) v dd = 15v g = +1v/v 0 2 4 6 8 10 12 14 16 time (20 s/div) output voltage (v) v dd = 15v g = -1v/v -1 1 3 5 7 9 11 13 15 17 time (0.1 ms/div) output voltage (v) v dd = 15v g = +2v/v v out v in downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 13 mcp6h01/2/4 note: unless otherwise indicated, t a =+25c, v dd = +3.5 v to +16 v, v ss = gnd, v cm =v dd /2 - 1.4v, v out ? v dd /2, v l =v dd /2, r l =10k ?? to v l and c l =60pf. figure 2-37: closed loop output impedance vs. frequency. figure 2-38: measured input current vs. input voltage (below v ss ). 1 10 100 1000 1.0e+01 1.0e+02 1.0e+03 1.0e+04 1.0e+05 1.0e+06 frequency (hz) closed loop output impedance ( ? ) g n : 101v/v 11v/v 1v/v 10 100 1k 10k 100k 1m 1.00e-12 1.00e-11 1.00e-10 1.00e-09 1.00e-08 1.00e-07 1.00e-06 1.00e-05 1.00e-04 1.00e-03 -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 v in (v) -i in (a) 1m 100 10 1 100n 10n 1n 100 p 10 p 1p t a = +125c t a = +85c t a = +25c t a = -40c downloaded from: http:/// mcp6h01/2/4 ds22243d-page 14 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 15 mcp6h01/2/4 3.0 pin descriptions descriptions of the pins are listed in table 3-1 . table 3-1: pin function table 3.1 analog outputs the output pins are low-impedance voltage sources. 3.2 analog inputs the non-inverting and inverting inputs are high-impedance cmos inputs with low bias currents. 3.3 power supply pins the positive power supply (v dd ) is 3.5v to 16v higher than the negative power supply (v ss ). for normal operation, the other pins are at voltages between v ss and v dd . typically, these parts can be used in single-supply operation or dual-supply operation. also, v dd will need bypass capacitors. 3.4 exposed thermal pad (ep) there is an internal electrical connection between the exposed thermal pad (ep) and the v ss pin; they must be connected to the same potential on the printed circuit board (pcb). mcp6h01 mcp6h02 mcp6h04 symbol description sc70-5, sot-23-5 soic2x3tdfnsoic2x3tdfn soic, tssop 16611 1v out , v outa analog output (op amp a) 42222 2v in C, v ina C inverting input (op amp a) 33333 3v in +, v ina + non-inverting input (op amp a) 57788 4 v dd positive power supply 5 5 5 v inb + non-inverting input (op amp b) 6 6 6 v inb C inverting input (op amp b) 7 7 7 v outb analog output (op amp b) 8 v outc analog output (op amp c) 9 v inc C inverting input (op amp c) 1 0 v inc + non-inverting input (op amp c) 24444 1 1 v ss negative power supply 1 2 v ind + non-inverting input (op amp d) 1 3 v ind C inverting input (op amp d) 1 4 v outd analog output (op amp d) 1, 5, 8 1, 5, 8 nc no internal connection 9 9 ep exposed thermal pad (ep); must be connected to v ss . downloaded from: http:/// mcp6h01/2/4 ds22243d-page 16 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 17 mcp6h01/2/4 4.0 application information the mcp6h01/2/4 family of op amps is manufactured using microchips state-of-the-art cmos process and is specifically designed for low-power, high-precision applications. 4.1 inputs 4.1.1 phase reversal the mcp6h01/2/4 op amps are designed to prevent phase reversal when the input pins exceed the supply voltages. figure 2-36 shows the input voltage exceeding the supply voltage without any phase reversal. 4.1.2 input voltage limits in order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the voltages at the input pins (see section 1.1 absolute maximum ratings ? ). the esd protection on the inputs can be depicted as shown in figure 4-1 . this structure was chosen to protect the input transistors against many (but not all) over-voltage conditions, and to minimize the input bias current (i b ). figure 4-1: simplified analog input esd structures. the input esd diodes clamp the inputs when they try to go more than one diode drop below v ss . they also clamp any voltages that go well above v dd . their breakdown voltage is high enough to allow normal operation, but not low enough to protect against slow overvoltage (beyond v dd ) events. very fast esd events (that meet the specification) are limited so that damage does not occur. in some applications, it may be necessary to prevent excessive voltages from reaching the op amp inputs; figure 4-2 shows one approach to protecting these inputs. figure 4-2: protecting the analog inputs. a significant amount of current can flow out of the inputs when the common mode voltage (v cm ) is below ground (v ss ), see figure 2-38 . 4.1.3 input current limits in order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the currents into the input pins (see section 1.1 absolute maximum ratings ? ). figure 4-3 shows one approach to protecting these inputs. the resistors r 1 and r 2 limit the possible currents in or out of the input pins (and the esd diodes, d 1 and d 2 ). the diode currents will go through either v dd or v ss . figure 4-3: protecting the analog inputs. 4.1.4 normal operation the inputs of the mcp6h01/2/4 op amps connect to a differential pmos input stage. it operates at a low common mode input voltage (v cm ), including ground. with this topology, the device operates with a v cm up to v dd C 2.3v and 0.3v below v ss (refer to figure 2-3 through 2-5 ). the input offset voltage is measured at v cm =v ss C 0.3v and v dd C 2.3v to ensure proper operation. bond pad bond pad bond pad v dd v in + v ss input stage bond pad v in C v 1 v dd d 1 v 2 d 2 mcp6h0x v out v 1 r 1 v dd d 1 r 1 > v ss ? (minimum expected v 1 ) 2ma r 2 > v ss ? (minimum expected v 2 ) 2ma v 2 r 2 d 2 r 3 v out mcp6h0x downloaded from: http:/// mcp6h01/2/4 ds22243d-page 18 ? 2010-2011 microchip technology inc. for a unity gain buffer, v in must be maintained below v dd C 2.3v for correct operation. 4.2 rail-to-rail output the output voltage range of the mcp6h01/2/4 op amps is 0.020v (typical) and 14.980v (typical) when r l =10k ? is connected to v dd /2 and v dd =15v. refer to figures 2-24 through 2-29 for more information. 4.3 capacitive loads driving large capacitive loads can cause stability problems for voltage feedback op amps. as the load capacitance increases, the feedback loops phase margin decreases and the closed-loop bandwidth is reduced. this produces gain peaking in the frequency response, with overshoot and ringing in the step response. while a unity-gain buffer (g = +1v/v) is the most sensitive to capacitive loads, all gains show the same general behavior. when driving large capacitive loads with these op amps (e.g., > 100 pf when g = + 1v/v), a small series resistor at the output (r iso in figure 4-4 ) improves the feedback loops phase margin (stability) by making the output load resistive at higher frequencies. the bandwidth will generally be lower than the bandwidth with no capacitance load. figure 4-4: output resistor, r iso stabilizes large capacitive loads. figure 4-5 gives the recommended r iso values for different capacitive loads and gains. the x-axis is the normalized load capacitance (c l /g n ), where g n is the circuits noise gain. for non-inverting gains, g n and the signal gain are equal. for inverting gains, g n is 1 + |signal gain| (e.g., -1v/v gives g n = +2v/v). after selecting r iso for your circuit, double check the resulting frequency response peaking and step response overshoot. modify r iso s value until the response is reasonable. bench evaluation and simulations with the mcp6h01/2/4 spice macro model are helpful. figure 4-5: recommended r iso values for capacitive loads. 4.4 supply bypass with this family of operational amplifiers, the power supply pin (v dd for single supply) should have a local bypass capacitor (i.e., 0.01 f to 0.1 f) within 2 mm for good high-frequency performance. it can use a bulk capacitor (i.e., 1 f or larger) within 100 mm to provide large, slow currents. this bulk capacitor can be shared with other analog parts. 4.5 unused op amps an unused op amp in a quad package (mcp6h04) should be configured as shown in figure 4-6 . these circuits prevent the output from toggling and causing crosstalk. circuit a sets the op amp at its minimum noise gain. the resistor divider produces any desired reference voltage within the output voltage range of the op amp, and the op amp buffers that reference voltage. circuit b uses the minimum number of components and operates as a comparator, but it may draw more current. figure 4-6: unused op amps. v in r iso v out c l C + mcp6h0x 1 10 100 1000 1.e-11 1.e-10 1.e-09 1.e-08 1.e-07 1.e-06 normalized load capacitance; c l /g n (f) recommended r iso ( ? ) g n : 1 v/v 2 v/v ? 5 v/v v dd = 16v r l = 10 k ? 10p 100p 1n 10n 0.1 1 1k v dd v dd r 1 r 2 v dd v ref v ref v dd r 2 r 1 r 2 + -------------------- ? = ? mcp6h04 (a) ? mcp6h04 (b) downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 19 mcp6h01/2/4 4.6 pcb surface leakage in applications where low input bias current is critical, pcb surface leakage effects need to be considered. surface leakage is caused by humidity, dust or other contamination on the board. under low-humidity condi- tions, a typical resistance between nearby traces is 10 12 ? . a 15v difference would cause 15 pa of current to flow; which is greater than the mcp6h01/2/4 familys bias current at +25c (10 pa, typical). the easiest way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). the guard ring is biased at the same voltage as the sensitive pin. an example of this type of layout is shown in figure 4-7 . figure 4-7: example guard ring layout for inverting gain. 1. non-inverting gain and unity-gain buffer: a. connect the non-inverting pin (v in +) to the input with a wire that does not touch the pcb surface. b. connect the guard ring to the inverting input pin (v in C). this biases the guard ring to the common mode input voltage. 2. inverting gain and trans-impedance gain amplifiers (convert current to voltage, such as photo detectors): a. connect the guard ring to the non-inverting input pin (v in +). this biases the guard ring to the same reference voltage as the op amp (e.g., v dd /2 or ground). b. connect the inverting pin (v in C) to the input with a wire that does not touch the pcb surface. 4.7 application circuits 4.7.1 difference amplifier the mcp6h01/2/4 op amps can be used in current sensing applications. figure 4-8 shows a resistor (r sen ) that converts the sensor current (i sen ) to voltage, as well as a difference amplifier that amplifies the voltage across the resistor while rejecting common mode noise. r 1 and r 2 must be well matched to obtain an acceptable common mode rejection ratio (cmrr). moreover, r sen should be much smaller than r 1 and r 2 in order to minimize the resistive loading of the source. to ensure proper operation, the op amp common mode input voltage must be kept within the allowed range. the reference voltage (v ref ) is supplied by a low-impedance source. in single-supply applications, v ref is typically v dd /2. . figure 4-8: high side current sensing using difference amplifier. guard ring v in Cv in + v ss r 1 v out r 2 r 1 r sen i sen r sen << r 1 , r 2 v out v 1 v 2 ? ?? r 2 r 1 ----- - ?? ?? v ref + = v ref r 2 v dd mcp6h01 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 20 ? 2010-2011 microchip technology inc. 4.7.2 two op amp instrumentation amplifier the mcp6h01/2/4 op amps are well suited for conditioning sensor signals in battery-powered applications. figure 4-9 shows a two op amp instrumentation amplifier using the mcp6h02, which works well for applications requiring rejection of common mode noise at higher gains. to ensure proper operation, the op amp common mode input voltage must be kept within the allowed range. the reference voltage (v ref ) is supplied by a low- impedance source. in single-supply applications, v ref is typically v dd /2. figure 4-9: two op amp instrumentation amplifier. to obtain the best cmrr possible, and not limit the performance by the resistor tolerances, set a high gain with the r g resistor. 4.7.3 photodetector amplifier the mcp6h01/2/4 op amps can be used to easily convert the signal from a sensor that produces an output current (such as a photo diode) into voltage (a trans-impedance amplifier). this is implemented with a single resistor (r 2 ) in the feedback loop of the amplifiers shown in figure 4-10 . the optional capacitor (c 2 ) sometimes provides stability for these circuits. a photodiode configured in photovoltaic mode has a zero voltage potential placed across it. in this mode, the light sensitivity and linearity is maximized, making it best suited for precision applications. the key amplifier specifications for this application are: low input bias current, common mode input voltage range (including ground), and rail-to-rail output. figure 4-10: photodetector amplifier. v out v 1 v 2 ? ?? 1 r 1 r 2 ----- - 2r 1 r g --------- ++ ?? ?? v ref + = v ref r 1 r 2 r 2 r 1 v out r g v 2 v 1 ? mcp6h02 ? mcp6h02 d 1 light v out v dd r 2 c 2 i d1 v out = i d1 *r 2 C + mcp6h01 downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 21 mcp6h01/2/4 5.0 design aids microchip provides the basic design tools needed for the mcp6h01/2/4 family of op amps. 5.1 spice macro model the latest spice macro model for the mcp6h01/2/4 op amp is available on the microchip web site at www.microchip.com. the model was written and tested in pspice owned by orcad (cadence). for other simulators, it may require translation. the model covers a wide aspect of the op amps electrical specifications. not only does the model cover voltage, current and resistance of the op amp, but it also covers the temperature and noise effects on the behavior of the op amp. the model has not been verified outside the specification range listed in the op amp data sheet. the model behaviors under these con- ditions cannot be guaranteed to match the actual op amp performance. moreover, the model is intended to be an initial design tool. bench testing is a very important part of any design and cannot be replaced with simulations. also, simulation results using this macro model need to be validated by comparing them to the data sheet specifications and characteristic curves. 5.2 filterlab software microchips filterlab software is an innovative software tool that simplifies analog active filter (using op amps) design. available at no cost from the microchip web site at www.microchip.com/filterlab, the filterlab design tool provides full schematic diagrams of the filter circuit with component values. it also outputs the filter circuit in spice format, which can be used with the macro model to simulate actual filter performance. 5.3 maps (microchip advanced part selector) maps is a software tool that helps semiconductor professionals efficiently identify microchip devices that fit a particular design requirement. available at no cost from the microchip web site at www.microchip.com/ maps, maps is an overall selection tool for microchips product portfolio that includes analog, memory, mcus and dscs. using this tool, you can define a filter to sort features for a parametric search of devices and export side-by-side technical comparison reports. helpful links are also provided for data sheets, purchases and sampling of microchip parts. 5.4 analog demonstration and evaluation boards microchip offers a broad spectrum of analog demonstration and evaluation boards that are designed to help you achieve faster time to market. for a com- plete listing of these boards and their corresponding users guides and technical information, visit the microchip web site: www.microchip.com/analogtools. some boards that are especially useful include: mcp6xxx amplifier evaluation board 1 mcp6xxx amplifier evaluation board 2 mcp6xxx amplifier evaluation board 3 mcp6xxx amplifier evaluation board 4 active filter demo board kit 5/6-pin sot-23 evaluation board, p/n vsupev2 8-pin soic/msop/tssop/ dip evaluation board, p/n soic8ev 5.5 application notes the following microchip analog design note and appli- cation notes are available on the microchip web site at www.microchip.com/appnotes, and are recommended as supplemental reference resources. adn003: ?select the right operational amplifier for your filtering circuits?, ds21821 an722: ?operational amplifier topologies and dc specifications?, ds00722 an723: ?operational amplifier ac specifications and applications?, ds00723 an884: ?driving capacitive loads with op amps?, ds00884 an990: ?analog sensor conditioning circuits ? an overview?, ds00990 an1177: ?op amp precision design: dc errors?, ds01177 an1228: ?op amp precision design: random noise?, ds01228 an1297: ?microchip?s op amp spice macro models?? ds01297 an1332: ?current sensing circuit concepts and fundamentals?? ds01332 these application notes and others are listed in: ?signal chain design guide?, ds21825 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 22 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 23 mcp6h01/2/4 6.0 packaging information 6.1 package marking information 5-lead sc-70 (mcp6h01) example 8-lead soic (150 mil) (mcp6h01, mcp6h02) example: xxxxxxxx xxxxyyww nnn mcp6h01e sn^^ 1103 256 legend: xx...x customer-specific information y year code (last digit of calendar year) yy year code (last 2 digits of calendar year) ww week code (week of january 1 is week 01) nnn alphanumeric traceability code pb-free jedec designator for matte tin (sn) * this package is pb-free. the pb-free jedec designator ( ) can be found on the outer packaging for this package. note : in the event the full microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 3 e 3 e 3 e example: 8-lead 2x3 tdfn (mcp6h01, mcp6h02) example: device code mcp6h01 2ann note: applies to 5-lead sot-23. device code mcp6h01 dhnn note: applies to 5-lead sc-70. dh25 xxnn xxnn 2a25 5-lead sot-23 (mcp6h01) aal 103 25 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 24 ? 2010-2011 microchip technology inc. package marking information 14-lead tssop ( mcp6h04 ) example: 14-lead soic (150 mil) ( mcp6h04 ) example: xxxxxxxxxxx yywwnnn xxxxxxxx yyww nnn 6h04e/st 1103 256 xxxxxxxxxxx mcp6h04 1103256 e/sl^^ 3 e downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 25 mcp6h01/2/4 d b 1 2 3 e1 e 4 5 ee c l a1 aa 2 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 26 ? 2010-2011 microchip technology inc. downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 27 mcp6h01/2/4 n b e e1 d 1 2 3 e e1 a a1 a2 c l l1 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 28 ? 2010-2011 microchip technology inc. noe: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 29 mcp6h01/2/4 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// mcp6h01/2/4 ds22243d-page 30 ? 2010-2011 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 31 mcp6h01/2/4 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 32 ? 2010-2011 microchip technology inc. noe: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 33 mcp6h01/2/4 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// mcp6h01/2/4 ds22243d-page 34 ? 2010-2011 microchip technology inc. downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 35 mcp6h01/2/4 noe: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// mcp6h01/2/4 ds22243d-page 36 ? 2010-2011 microchip technology inc. noe: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 37 mcp6h01/2/4 downloaded from: http:/// mcp6h01/2/4 ds22243d-page 38 ? 2010-2011 microchip technology inc. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 39 mcp6h01/2/4 note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// mcp6h01/2/4 ds22243d-page 40 ? 2010-2011 microchip technology inc. noe: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 41 mcp6h01/2/4 appendix a: revision history revision d (december 2011) the following is the list of modifications: 1. added the sc70-5 and sot-23-5 packages for the mcp6h01 device and updated all related information throughout the document. revision c (march 2011) the following is the list of modifications: 1. added new device mcp6h04. 2. updated table 3-1 with mcp6h04 pin names and details. revision b (october 2010) the following is the list of modifications: 1. updated section 4.1 inputs. revision a (march 2010) original release of this document. downloaded from: http:/// mcp6h01/2/4 ds22243d-page 42 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 43 mcp6h01/2/4 product identification system to order or obtain information, e. g., on pricing or delivery, refer to the factory or the listed sales office . device: mcp6h01t: single op amp (tape and reel) (sc-70, sot-23) mcp6h01: single op amp mcp6h01t: single op amp (tape and reel) (soic and 2x3 tdfn) mcp6h02: dual op amp mcp6h02t: dual op amp (tape and reel) (soic and 2x3 tdfn) mcp6h04: quad op amp mcp6h04t: quad op amp (tape and reel) (soic and tssop) temperature range: e = -40c to +125c package: lt = plastic package (sc-70), 5-lead ot = plastic small outline transistor (sot-23), 5-lead mny * = plastic dual flat, no lead, (2x3 tdfn) 8-lead sn = lead plastic small outline (150 mil body), 8-lead sl = plastic small outline, (150 mil body), 14-lead st = plastic thin shrink small outline (150 mil body), 14-lead * y = nickel palladium gold manufacturing designator. only available on the tdfn package. part no. /xx package temperature range device examples: a) mcp6h01t-e/lt: tape and reel, 5ld sc70 pkg b) mcp6h01t-e/ot: tape and reel, 5ld sot-23 pkg c) mcp6h01-e/sn: 8ld soic pkg d) mcp6h01t-e/sn: tape and reel, 8ld soic pkg e) mcp6h01t-e/mny: tape and reel, 8ld 2x3 tdfn pkg f) mcp6h02-e/sn: 8ld soic pkg g) mcp6h02t-e/sn: tape and reel, 8ld soic pkg h) mcp6h02t-e/mny: tape and reel 8ld 2x3 tdfn pkg i) mcp6h04-e/sl: 14ld soic pkg j) mcp6h04t-e/sl: tape and reel, 14ld soic pkg k) mcp6h04-e/st: 14ld soic pkg l) mcp6h04t-e/st: tape and reel, 14ld tssop pkg -x downloaded from: http:/// mcp6h01/2/4 ds22243d-page 44 ? 2010-2011 microchip technology inc. notes: downloaded from: http:/// ? 2010-2011 microchip technology inc. ds22243d-page 45 information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application meets with your specifications. microchip makes no representations or warranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip devices in life support and/or safety applications is entirely at the buyers risk, and the buyer agrees to defend, indemnify and hold harmless microchip from any and all damages, claims, suits, or expenses resulting from such use. no licenses are conveyed, implicitly or otherwise, under any microchip intellectual property rights. trademarks the microchip name and logo, the microchip logo, dspic, k ee l oq , k ee l oq logo, mplab, pic, picmicro, picstart, pic 32 logo, rfpic and uni/o are registered trademarks of microchip technology incorporated in the u.s.a. and other countries. filterlab, hampshire, hi-tech c, linear active thermistor, mxdev, mxlab, seeval and the embedded control solutions company are registered trademarks of microchip technology incorporated in the u.s.a. analog-for-the-digital age, application maestro, chipkit, chipkit logo, codeguard, dspicdem, dspicdem.net, dspicworks, dsspeak, ecan, economonitor, fansense, hi-tide, in-circuit serial programming, icsp, mindi, miwi, mpasm, mplab certified logo, mplib, mplink, mtouch, omniscient code generation, picc, picc-18, picdem, picdem.net, pickit, pictail, real ice, rflab, select mode, total endurance, tsharc, uniwindriver, wiperlock and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of microchip technology incorporated in the u.s.a. all other trademarks mentioned herein are property of their respective companies. ? 2010-2011, microchip technology incorporated, printed in the u.s.a., all rights reserved. printed on recycled paper. isbn: 978-1-61341-927-4 note the following details of the code protection feature on microchip devices: microchip products meet the specification cont ained in their particular microchip data sheet. microchip believes that its family of products is one of the most secure families of its kind on the market today, when used i n the intended manner and under normal conditions. there are dishonest and possibly illegal methods used to breach the code protection feature. all of these methods, to our knowledge, require using the microchip products in a manner outside the operating specif ications contained in microchips data sheets. most likely, the person doing so is engaged in theft of intellectual property. microchip is willing to work with the customer who is concerned about the integrity of their code. neither microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as unbreakable. code protection is constantly evolving. we at microchip are co mmitted to continuously improvin g the code protection features of our products. attempts to break microchips code protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona; gresham, oregon and design centers in california and india. the company?s quality system processes and procedures are for its pic ? mcus and dspic ? dscs, k ee l oq ? code hopping devices, serial eeproms, microperipherals, nonvolatile memory an d analog products. in addition, microchip?s quality system for the design and manufacture of development systems is iso 9001:2000 certified. downloaded from: http:/// ds22243d-page 46 ? 2010-2011 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://www.microchip.com/ support web address: www.microchip.com atlanta duluth, ga tel: 678-957-9614 fax: 678-957-1455 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 cleveland independence, oh tel: 216-447-0464 fax: 216-447-0643 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit farmington hills, mi tel: 248-538-2250 fax: 248-538-2260 indianapolis noblesville, in tel: 317-773-8323 fax: 317-773-5453 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 santa clara santa clara, ca tel: 408-961-6444 fax: 408-961-6445 toronto mississauga, ontario, canada tel: 905-673-0699 fax: 905-673-6509 asia/pacific asia pacific office suites 3707-14, 37th floor tower 6, the gateway harbour city, kowloon hong kong tel: 852-2401-1200 fax: 852-2401-3431 australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8569-7000 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8665-5511 fax: 86-28-8665-7889 china - chongqing tel: 86-23-8980-9588 fax: 86-23-8980-9500 china - hangzhou tel: 86-571-2819-3187 fax: 86-571-2819-3189 china - hong kong sar tel: 852-2401-1200 fax: 852-2401-3431 china - nanjing tel: 86-25-8473-2460 fax: 86-25-8473-2470 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8203-2660 fax: 86-755-8203-1760 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7252 fax: 86-29-8833-7256 china - xiamen tel: 86-592-2388138 fax: 86-592-2388130 china - zhuhai tel: 86-756-3210040 fax: 86-756-3210049 asia/pacific india - bangalore tel: 91-80-3090-4444 fax: 91-80-3090-4123 india - new delhi tel: 91-11-4160-8631 fax: 91-11-4160-8632 india - pune tel: 91-20-2566-1512 fax: 91-20-2566-1513 japan - osaka tel: 81-66-152-7160 fax: 81-66-152-9310 japan - yokohama tel: 81-45-471- 6166 fax: 81-45-471-6122 korea - daegu tel: 82-53-744-4301 fax: 82-53-744-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - kuala lumpur tel: 60-3-6201-9857 fax: 60-3-6201-9859 malaysia - penang tel: 60-4-227-8870 fax: 60-4-227-4068 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-5778-366 fax: 886-3-5770-955 taiwan - kaohsiung tel: 886-7-536-4818 fax: 886-7-330-9305 taiwan - taipei tel: 886-2-2500-6610 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-39 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 uk - wokingham tel: 44-118-921-5869 fax: 44-118-921-5820 worldwide sales and service 11/29/11 downloaded from: http:/// |
Price & Availability of MCP6H02-ESN
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |