data sheet part number 856020 140 mhz saw filter subject to change or obsolescence without notice rev e 11/07 ? triquint semiconductor page 1 of 6 features for broadband applications typical 3db bandwidth of 65 mhz high attenuation single-ended operation ceramic surface mount package (smp) replaces sawtek p/n 851948 (bw 3db=64 mhz) hermetic rohs compliant (2002/95/ec), pb-free package pin configuration surface mount 9.00 x 7.01 x 1.50 mm bottom view smp-35b 5 4 10 9 8 7 6 3 2 1 single-ended configuration pin no. description 4 output 5 output return 9 input 10 input return 1,2,3,6,7,8 case ground 0.76 9.00 2.54 2.54 1.12 1.02 7.01 1.80 1.50 nom. 1.65 max. 1.02 x 2.54 dimensions shown are nominal in millimeters all tolerances are 0.15mm except overall length and width +0.10mm/-0.15mm body: al 2 o 3 ceramic lid: kovar , ni plated terminations: au plating 0.5 - 1.0 m m, over a 2 - 6 m m ni plating pb
data sheet part number 856020 140 mhz saw filter subject to change or obsolescence without notice rev e 11/07 ? triquint semiconductor page 2 of 6 electrical specifications (1) operating temperature range: (2) 0 to +70 o c parameter (3) minimum typical (4) maximum unit center frequency - 140 - mhz minimum insertion loss - 17.8 20 db lower 1 db bandedge (5) upper 1 db bandedge - 168.25 108.85 170.27 111.75 - mhz mhz lower 3 db bandedge (5) upper 3 db bandedge - 171.5 107.45 172.61 108.5 - mhz mhz lower 40 db bandedge (5) upper 40 db bandedge 98 - 102.35 180.78 - 182 mhz mhz amplitude variation 111.75 - 168.25 mhz - 0.6 1.0 db p-p phase linearity 111.75 - 168.25 mhz - 5.35 10 deg p-p group delay variation 111.75 - 168.25 mhz - 21 55 ns p-p absolute delay - 0.539 - m sec relative attenuation (5) 15 - 75 mhz 75 - 98 mhz 182 - 205 mhz 205 - 350 mhz 45 40 40 45 51 50 43 50 - - - - db db db db terminating source impedance (6) - 50 - w terminating load impedance (6) - 50 - w substrate material - 128 linbo 3 - - temperature coefficient of frequency - -74 - ppm/ o c notes : 1. all specifications are based on the triquint tes t circuit shown below 2. in production, devices will be tested at room te mperature to a guardbanded specification to ensure electrical compliance over temperature 3. electrical margin has been built into the design to account for the variations due to temperature a nd manufacturing tolerances 4. typical values are based on average measuremen ts at room temperature 5. all attenuation measurements are measured relati ve to minimum insertion loss 6. this is the optimum impedance in order to achiev e the performance shown test circuit: actual matching values may vary due to pcb layout a nd parasitics 50 w single-ended input 1,2,3,5 6,7,8,10 50 w ww w 27nh 9 4 56nh 50 w ww w 47pf 33nh 22pf 50 w single-ended output
data sheet part number 856020 140 mhz saw filter subject to change or obsolescence without notice rev e 11/07 ? triquint semiconductor page 3 of 6 electrical specifications (1) operating temperature range: (2) -40 to +85 o c parameter (3) minimum typical (4) maximum unit center frequency - 140 - mhz minimum insertion loss - 17.8 20 db lower 1.5 db bandedge (5) upper 1.5 db bandedge - 168.25 108.85 170.27 111.75 - mhz mhz lower 3 db bandedge (5) upper 3 db bandedge - 171.30 107.45 172.61 108.70 - mhz mhz lower 40 db bandedge (5) upper 40 db bandedge 98 - 102.35 180.78 - 182.30 mhz mhz amplitude variation 111.75 - 168.25 mhz - 0.6 1.5 db p-p phase linearity 111.75 - 168.25 mhz - 5.35 10 deg p-p group delay variation 111.75 - 168.25 mhz - 21 70 ns p-p absolute delay - 0.539 - m sec relative attenuation (5) 15 - 75 mhz 75 - 98 mhz 182 - 205 mhz 205 - 350 mhz 45 40 39 45 51 50 43 50 - - - - db db db db terminating source impedance (6) - 50 - w terminating load impedance (6) - 50 - w substrate material - 128 linbo 3 - - temperature coefficient of frequency - -74 - ppm/ o c notes : 1. all specifications are based on the triquint tes t circuit shown below 2. in production, devices will be tested at room te mperature to a guardbanded specification to ensure electrical compliance over temperature 3. electrical margin has been built into the design to account for the variations due to temperature a nd manufacturing tolerances 4. typical values are based on average measurements at room temperature 5. all attenuation measurements are measured relati ve to minimum insertion loss 6. this is the optimum impedance in order to achiev e the performance shown test circuit: actual matching values may vary due to pcb layout a nd parasitics 50 w single-ended input 1,2,3,5 6,7,8,10 50 w ww w 27nh 9 4 56nh 50 w ww w 47pf 33nh 22pf 50 w single-ended output
data sheet part number 856020 140 mhz saw filter subject to change or obsolescence without notice rev e 11/07 ? triquint semiconductor page 4 of 6 typical performance (at room temperature)
data sheet part number 856020 140 mhz saw filter subject to change or obsolescence without notice rev e 11/07 ? triquint semiconductor page 5 of 6 matching schematics actual matching values may vary due to pcb layout a nd parasitics 50 w single-ended input 1,2,3,5 6,7,8,10 50 w ww w 27nh 9 4 56nh 50 w ww w 47pf 33nh 22pf 50 w single-ended output marking pcb footprint date code id dot sawtek xxxxxx 856020 1.22 9.19 1.32 1.22 3.76 1.32 1.32 2.07 7.21 the date code consists of: day of the current year (julian, 3 digits), last digit of the year (1 digit) and hou r (2 digits) this footprint represents a recommendation only dimensions shown are nominal in millimeters tape and reel a a ?1.5 12.0 4.0 ?1.5 2.0 9.22 7.22 2.2 section a-a 0.3 16.0 7.5 1.75 ?13.0 ?20.2 ?102 ?330 16.8 2.7 id dot direction of travel 2.0 dimensions shown are nominal in millimeters packaging quantity: 2000 units/reel
data sheet part number 856020 140 mhz saw filter subject to change or obsolescence without notice rev e 11/07 ? triquint semiconductor page 6 of 6 maximum ratings parameter symbol minimum maximum unit operating temperature range t -40 +85 o c storage temperature range t stg -40 +85 o c important notes warnings electrostatic sensitive device (esd) avoid ultrasonic exposure rohs compliance this product complies with eu directive 2002/95/ec (rohs) solderability compatible with jesd22-b102, pb-free process, 260c peak reflow temperature ( see soldering profile ) links to additional technical information pcb layout tips qualification flowchart soldering profile s-parameters rohs information other technical information triquints liability is limited only to the surface acoustic wave (saw) component(s) described in this data sheet. triquint does not accept any liabilit y for applications, processes, circuits or assemblies , which are implemented using any triquint componen t described in this data sheet. contact information po box 609501 orlando, fl 32860-9501 usa phone: +1 (407) 886-8860 fax: +1 (407) 886-7061 email: info-product@tqs.com web: www.triquint.com or contact one of our worldwide network of sales offices, representatives or distributors pb
|
