features carbon element assortment of resistance tapers dual gang element center detent option PTJ90 series dual concentric shaft panel control w/push-push switch *rohs directive 2002/95/ec jan 27, 2003 including annex. speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. electrical characteristics standard resistance range ............................1k ohms to 1 megohm standard resistance tolerance r < 250k ohms .............................20 % r 250k ohms .............................30 % end resistance r < 50k ohms .................. 30 ohms max. r 50k ohms ............. 0.1 % of tr max. insulation resistance @ 250 vdc ................................. 100 megohms min. dielectric withstanding voltage ....300 vac standard taper ...................... linear, audio power rating linear ....................................... 0.05 watt audio ...................................... 0.025 watt slider noise ...........................100 mv max. operating voltage ........... 50 vac / 10 vdc environmental characteristics operational life .................... 15,000 cycles tr shift .........................................15 % operating temperature range ......................................-10 c to +55 c resistance to solder heat ..................5 % ip rating .............................................ip 40 mechanical characteristics mechanical angle ....................... 300 3 operating torque ..................20~250 gf-cm stop strength........................ 5 kgf-cm min. mounting torque ................ 10 kgf-cm max. shaft push/pull strength ......... 10 kgf max. soldering condition manual ............... 300 c 5 c for 3 sec. wave .................. 260 c 5 c for 5 sec. wash ......................... not recommended hardware ....................one ? at washer and one mounting nut supplied with each potentiometer switch characteristics power rating .......................3 a @ 16 vdc contact resistance .............. 100 milliohms dielectric strength bushing to terminals .................300 vac switch terminals .........................50 vac insulation resistance bushing to terminals @ 250 vac ......................................... 100 megohms switch terminals @ 50 vac ........................................... 10 megohms switch type .................. push on - push off contact arrangement........................ spdt switch stroke......................... 1.5 0.1 mm operating force......................... 2 kgf max. operating life ....................... 10,000 cycles product dimensions mounting hole detail locating lug detail 20.0 (0.787) 30.0 ?1.0 (1.181 ?0.039) 7.0 (0.276) 8.2 (0.323) 8.5 (0.335) 10.0 (0.394) 25.8 (1.016) 0.8 ?0.2 (0.031 ?0.002) 3.5 +0/-0.05 (0.138 +0/-0.002) 6.0 + 0/-0.05 (0.236 +0/-0.002) dia. c0.5 r2 r1 0.75 (0.030) m9 x dia. 2.5 +0/-0.1 (0.098 +0/-0.004) 5.0 + 0/-0.1 (0.197 +0/-0.004) 1.5 ?0.5 (0.059 ?0.020) switch travel 9.5 (0.374) 0.9 ?0.1 (0.035 ?0.004) inner and outer shaft shown in ccw position xx y y 60 3.5 (0.138) 4.85 (0.191) 6.5 ?0.5 (0.256 ?0.002) 2.0 ?0.1 (0.079 ?0.004) y y xx 0.8 ?0.2 (0.315 ?0.008) 6.0 ?0.2 (0.236 ?0.008) 5.0 (0.197) 6.8 (0.268) 4.0 (0.157) 5.0 (0.197) 5.0 (0.197) 1.0 +0.1/-0 (0.039 +0.004/-0) dia. mounting surface ac df 10 plcs. PTJ902-xxxs r2 r1 9.5 (0.374) 0.9 ?0.1 (0.035 ?0.004) inner and outer shaft shown in ccw position x x y 60 3.5 (0.138) 4.85 (0.191) 6.5 ?0.5 (0.256 ?0.002) 20.0 (0.787) 30.0 ?1.0 (1.181 ?0.039) 8.0 (0.315) 5.0 (0.197) 10.0 (0.394) 25.8 (1.016) 6.7 + 0/-0.05 (0.264 +0/-0.002) dia. dia. c0.5 0.75 (0.030) m9 x 1.5 ?0.1 (0.059 ?0.004) 3.0 +0.1/-0 (.118 +0.004/-0) 4.7 + 0/-0.05 (0.185 +0/-0.002) 1.5 ?0.5 (0.059 ?0.020) switch travel PTJ902-xxxf dimensions: mm (inches) *rohs compliant m7 x washer nut 2.0 (.079) 0.5 (.020) dia. 7.2 (.283) dia. 11.0 (.433) dia. 12.7 (.500) 0.75 (.030) dia. 12.0 (.472) hardware
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. PTJ90 series dual concentric shaft panel control w/push-push switch tapers 010 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 90 90 100 100 a series tapers terminal 1 output voltage across terminals 1-2 input voltage across terminals 1-3 x 100 (%) terminal 3 rotational travel (%) (05a);a1 (10a);a2 (15a);a3 (20a);a4 (25a);a5 (30a);a6 010 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 90 90 100 100 b series tapers terminal 1 output voltage across terminals 1-2 input voltage across terminals 1-3 x 100 (%) terminal 3 rotational travel (%) (4 b );b 4 (3b);b3 (2b);b2 (1b);b1 (5b);b5 010 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 90 90 100 100 c series tapers terminal 1 output voltage across terminals 1-2 input voltage across terminals 1-3 x 100 (%) terminal 3 rotational travel (%) (05c);c1 (10 c);c2 (15c);c3 (20c);c4 (25 c);c5 (30c);c6 rev. 10/11 how to order PTJ90 2 - 0 30 f - 103 b2 model number designator PTJ90 = dual concentric shaft panel control w/push-push switch number of sections 2 = dual gang center detent 0 = no detent 1 = center detent shaft length (fms) 30 = 30 mm shaft style f = flatted metal s = slotted metal resistance code (see standard resistance table) resistance taper (see taper charts) taper series followed by curve number standard resistance table resistance resistance (ohms) code 1,000 102 2,000 202 5,000 502 10,000 103 20,000 203 50,000 503 100,000 104 200,000 204 500,000 504 1,000,000 105 applications multimedia sound systems mixers / drums / dj equipment automotive sound systems portable electronics portable appliances 3 2 1 r1 3' 2' 1' r2 switch circuit schematic dual gang outer connection ac df
|
