le200s-cd 200w single output led driver series 1 www.slpower.com le200s-cd rev 2.0,11-feb-13 features high efficiency (up to 93%) wide range universal input 90-305 vac active power factor correction (0.99 typical) constant current output dimming function lightning protection waterproof (ip67) overcurrent, overvoltage, overtemperature protection meets ul8750 & en61347 safety 3 year warranty description the le200s-cd series operate from a 90 ~ 305vac inp ut range. these units will provide up to a 0.7a of output current and a maximum output voltage of 285v dc for 200 w maximum output power. they are designe d to be highly efficient and highly reliable. the sta ndard features include dimming control, lightning p rotection, over voltage protection, short circuit protection, and over temperature protection. model selection model output output efficiency* ripple & regulation overvoltage number current voltage 110vac 220vac noise** line load trip level LE200S70CD 665ma-735ma 143v ? 285v 90%-91% 92%-93% 8.6v pk-pk max. 1% 3% 342v ? 428v notes: 1. efficiency measured at full load, at inp ut voltage noted. 2. measured at 20mhz bandwidth, with noise probe d irectly across output terminals, and load terminate d with 0.1 f ceramic and 10 f low esr electrolytic capacitors. general specifications ac input 90-305vac, 47-63hz, 1 ? turn on time 1.0 seconds, max. input current 100vac: 2.4a, 220vac: 1.2a overload protection constant current inrush current 230vac, cold start: will not exceed 65a dimming function 1-10vdc source or external resistor can be used for dimming control. see below. input fuses xa, 250vac fuses provided on all models
le200s-cd 200w single output led driver series 2 www.slpower.com le200s-cd rev 2.0,11-feb-13 general specifications (continued) earth leakage current <0.75ma@277vac, 50hz short circuit protection provided - no damage to unit, self-recovery. efficiency see models chart. overvoltage protection latch mode. ac input will need to be reset to return to normal operation after an ovp condition. see chart for trip range. output power 200w continuous overtemperature protection latch mode. ac input will need to be reset to return to normal operation after an otp condition. trip temperature = 110c typical. ripple and noise see chart operating temperature operating: -35c to +70c non-operating: -40c to +85c output voltage see chart relative humidity 10% to 100% operating 5% to 100%, non-operating total regulation +/- 3%. see chart safety standards ul8750, ul935, ul1012, csa-c22.2 no. 107.1, en61347-1, en61347-2-13 dimensions w: 3.13? x l: 9.37? x h: 1.81? mtbf 330,000 hours (450ma model, 110vac input, 80% load, 25c ambient, per mil-hdbk-217f). weight 1500g lifetime 90,000 hours (1400ma model, at 110vac input, 80% load, 45c ambient temperature). emi/emc compliance emissions en55015, radiated & conducted with 6db of margin emi for lighting equipment en61547 static discharge immunity en61000-4-2, 4kv contact discharge, 8kv air dischar ge radiated rf immunity en61000-4-3 eft/burst immunity en61000-4-4 line surge immunity en61000-4-5, 4kv line-line, 6kv line-earth conducted rf immunity en61000-4-6 power frequency magnetic field immunity en61000-4-8 voltage dip immunity en61000-4-11 line harmonic emissions en61000-3-2 flicker test en61000-3-3
le200s-cd 200w single output led driver series 3 www.slpower.com le200s-cd rev 2.0,11-feb-13 derating curves mechanical drawing
le200s-cd 200w single output led driver series 4 www.slpower.com le200s-cd rev 2.0,11-feb-13 dimming control the dimmer control may be operated from either a po tentiometer or from an input signal of 1 ? 10 vdc. two recommended implementations are provided below. parameters: parameter min. typ. max. notes absolute max. voltage on the 1-10v input -2v - 12v sink current on the 1-10v input pin 0ma - 1ma dimming configuration using external voltage dimming configuration using external resistance dimming control notes: 1. io is actual output current and ir is rated cur rent without dimming control. 2. for the driver to operate properly, the load vo ltage must be maintained above the minimum voltage threshold (approx. 50% of the max. output voltage for any given model). 3. if the output voltage is maintained above 50% o f the maximum output voltage, the dimming control m ay be operated over the entire 1-10v range with outp ut current varying from 100% down to practically 10 %. 4. the dimming signal is allowed to be less than 1 v, however, when it for 0-1v, the output current is 10%io. 5. do not connect the gnd of dimming to the output ; otherwise, the led driver can not work normally. data sheet ? 2012 sl power electronics corp. the i nformation and specifications contained herein are believed to be correct at the time of publication. however, sl power accepts no responsibility for consequences arising from reproduction errors or in accuracies. specifications are subject to change w ithout notice. le150sxxxcd le200sxxxcd
|
