![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
1 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series new device series offers high static dv/dt and lower turn off (t q ) sensitive scr with its small die planar construction design. it is specifcally designed for gfci (ground fault circuit interrupter) and gas ignition applications. all scrs junctions are glass-passivated to ensure long term reliability and parametric stability. description features absolute maximum ratings symbol parameter value unit i t(rms) rms on-state current (full sine wave) to-92 t c = 55c 0.8 a sot-89 t c = 60c 0.8 a sot-223 t l = 60c 0.8 a i t(av) average on-state current to-92 t c = 55c 0.51 a sot-89 t c = 60c 0.51 a sot-223 t l = 60c 0.51 a i tsm non repetitive surge peak on-state current (single cycle, t j initial = 25c) to-92 sot-89 sot-223 f= 50hz 8 a f= 60hz 10 a i 2 t i 2 t value for fusing t p = 10 ms f = 50 hz 0.32 a 2 s t p = 8.3 ms f = 60 hz 0.41 a 2 s di/dt critical rate of rise of on-state current i g = 10ma to-92 sot-89 sot-223 t j = 125c 50 a/s i gm peak gate current t p = 10 s t j = 125c 1. 0 a p g(av) average gate power dissipation t j = 125c 0.1 w t stg storage junction temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c main features symbol value unit i t(rms) 0.8 a v drm /v rrm 400 to 800 v i gt 5 to 200 a a k g schematic symbol the sxx8xsx ev series is specifcally designed for gfci (ground fault circuit interrupter) and gas ignition applications. applications ? rohs compliant and halogen-f ree ? thr u-hole and surface mount packages ? surge current capability > 10amps ? blocking v oltage ( v drm / v rrm ) capability - up to 800v ? high dv/dt noise immunity ? improv ed turn-off time (t q ) < 25 sec ? sensitive gate f or direct microprocessor interface sxx8xsx series rohs
2 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series electrical characteristics (t j = 25c, unless otherwise specifed) symbol description test conditions limit value unit sxx8ys1 sxx8ys2 sxx8ys i gt dc gate trigger current v d = 6v r l = 100 min. 0.5 1 15 a max. 5 50 200 a v gt dc gate trigger voltage v d = 6v r l = 100 max. 0.8 v v grm peak reverse gate voltage i rg = 10a min. 5 v i h holding current r gk = 1 k? initial current = 20ma max. 5 ma (dv/dt)s critical rate-of-rise of off-state voltage t j = 125c v d = v drm /v rrm exp. waveform r gk =1 k min. 75 v/s v gd gate non-trigger voltage v d = v drm r gk =1 k t j = 25c min. 0.2 v t q turn-off time t j = 25c @ 600 v r gk =1 k max. 30 25 25 s t gt turn-on time i g =10ma pw = 15sec i t = 1.6a(pk) typ. 2.0 2.0 2.0 s static characteristics (t j = 25c, unless otherwise specifed) symbol description test conditions limit value unit v tm peak on-state voltage i tm = 1.6a (pk) max. 1.70 v i drm off-state current, peak repetitive t j = 25c @ v d = v drm r gk =1 k max. 3 a t j = 125c @ vd = v drm r gk =1 k max. 500 a thermal resistances symbol description test conditions value unit r th(j-c) junction to case (ac) i t = 0.8a (rms) 1 to-92 75 c/ w sot-223 30 c/ w sot-89 50 c/ w r th(j-a) junction to ambient i t = 0.8a (rms) 1 to-92 150 c/ w sot-223 60 c/ w sot-89 90 c/ w 1 60hz ac resistive load condition, 100% conduction. note: x = voltage, y = package 3 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series figure 3: normaliz ed dc gate trigger voltage vs. junction temperature -40 -25 -10 +5 +20 +35 +50 +65 +80 +95 +110 +125 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 junction temperature (t j ) - c gate trigger voltage (v gt ) - v figure 1: normaliz ed dc gate trigger current for all quadrants vs. junction temperature -40 -15 +25 +65 +105 0.0 0.5 1. 0 1. 5 2.0 junction temperature (t j ) - c ratio of +125 i gt i gt (t j = 25c) figure 4: power dissipation (typical) vs. rms on-state current figure 2: normaliz ed dc holding current vs. junction temperature -55 -35 -1 5+ 5 +25 +45 +65 +85 +105 0.0 1. 0 2.0 3.0 4.0 junction temperature (t j ) - c +125 i h (t j = 25c) i h ratio of figure 5: maximum allo wable case temperature vs. on-state current 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 50 60 70 80 90 10 0 11 0 12 0 13 0 rms on-state current [i t(rms) ] - amps maximum all ow able case temperature (t c ) - o c to-92 sot-223 & sot-89 current wa veform: sinusoidal lo ad: resistive or inductive conduction angle: 18 0 o case temperature: measured as shown on dimensional drawings 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 rms on-state current [i t(rms) ] - amps av erage on-state p ower dissipation [p d(av) ] - wa tt s current wa veform: sinusoidal lo ad: resistive or inductive conduction angle: 18 0 o 4 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series figure 6: surg e peak on-state current vs. number of cycles soldering parameters refow condition pb C free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 180 secs average ramp up rate (liquidus temp) (t l ) to peak 5c/second max t s(max) to t l - ramp-up rate 5c/second max refow - temperature (t l ) (liquidus) 217c - time (min to max) (t s ) 60 C 150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 5c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c sur ge current du ra tion - fu ll cycle 1 23 45 6 7 89 10 20 30 40 60 80 100 200 300 400 600 1000 1 2 3 4 5 6 7 8 9 10 20 peak sur ge (non-repetitive) on-state current (i ts m ) ? am ps . 0.8 a devices supply frequency: 60hz sinusoidal load: resistive rms on-state current [i t(rms) ]: max rated value at specifc case temperature notes: 1. gate control may be lost during and immediately following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value. ti me temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p r e h eat ramp-up ramp-up ramp-down r am p - do 5 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series physical specifcations terminal finish 100% matte tin-plated. body material ul recognized epoxy meeting fammability classifcation 94v-0. lead material copper alloy reliability/environmental tests test specifcations and conditions ac blocking mil-std-750, m-1040, cond a applied peak ac voltage @ 110c for 1008 hours temperature cycling mil-std-750, m-1051, 100 cycles; -40c to +150c; 15-min dwell-time temperature/ humidity eia / jedec, jesd22-a101 1008 hours; 320v - dc: 85c; 85% rel humidity high temp storage mil-std-750, m-1031, 1008 hours; 150c low-temp storage 1008 hours; -40c thermal shock mil-std-750, m-1056 10 cycles; 0c to 100c; 5-min dwell- time at each temperature; 10 sec (max) transfer time between temperature autoclave eia / jedec, jesd22-a102 168 hours (121c at 2 atms) and 100% r/h resistance to solder heat mil-std-750 method 2031 solderability ansi/j-std-002, category 3, test a lead bend mil-std-750, m-2036 cond e design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way toward extending the operating life of the thyristor. good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage. dimensions C to-92 dimension inches millimeters min max min max a 0.175 0.205 4.450 5.200 b 0.170 0.210 4.320 5.330 c 0.500 12.70 d 0.135 3.430 e 0.125 0.165 3.180 4.190 f 0.080 0.105 2.040 2.660 g 0.016 0.021 0.407 0.533 h 0.045 0.055 1.150 1.390 i 0.095 0.105 2.420 2.660 j 0.015 0.020 0.380 0.500 a g h i f e j d f c b t measuring point c seating plane gate anode cathode 6 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series dimensions C sot-223 dimensions in millimeters (inches) recommended soldering footprint for sot223 1. 5 (0.059?) 1. 5 (0.059?) 3.3 (0.130?) 6.4 (0.252?) 4.6 (0.181?) 1. 2 (0.047?) 2.3 (0.091?) (3x) anode gate anode cathode .064 (1.63) .154 (3.91) .036 (0.91) .044 (1.12) .047 (1.19) .087 (2.21) .064 (1.63) pad layout for sot-89 dimensions in millimeters (inches) dimensions C sot-89 anode gate anode cathode anode gate anode cathode f g a j d b e c h g a fd b c e tc measuring point anode cathode anode gate f g a j d b e c h g a fd b c e tc measuring point anode cathode anode gate dimension inches millimeters min typ max min typ max a 0.173 0.181 4.40 4.60 b 0.090 0.102 2.29 2.60 c 0.055 0.063 1.40 1.60 d 0.155 0.167 3.94 4.25 e 0.035 0.047 0.89 1.20 f 0.056 0.062 1.42 1.57 g 0.115 0.121 2.92 3.07 h 0.014 0.017 0.35 0.44 i 0.014 0.019 0.36 0.48 j 0.064 0.072 1.62 1.83 f g a j d b e c h g a fd b c e tc measuring point anode cathode anode gate dimensions inches millimeters min typ max min typ max a 0.248 0.256 0.264 6.30 6.50 6.70 b 0.130 0.138 0.146 3.30 3.50 3.70 c 0.071 1.80 d 0.001 0.004 0.02 0.10 e 0.114 0.118 0.124 2.90 3.00 3.15 f 0.024 0.027 0.034 0.60 0.70 0.85 g 0.090 2.30 h 0.181 4.60 i 0.264 0.276 0.287 6.70 7. 0 0 7.30 j 0.009 0.010 0.014 0.24 0.26 0.35 k 10 max anode gate anode cathode f g a j d b e c h g a fd b c e tc measuring point anode cathode anode gate 7 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series packing options part number marking weight packing mode base quantity sxx8esy sxx8esy 0.170g bulk 2500 sxx8esyap sxx8esy 0.170g ammo pack 2000 sxx8esyrp sxx8esy 0.170g tape & reel 2000 sxx8tsyrp sxx8tsy 0.120g tape & reel 1000 sxx8bsrp xx8 0.053g tape & reel 1000 sxx8bsrp1 xx8 0.053g tape & reel 1000 note: x = voltage, y = gate sensitivity part number voltage gate sensitivity package 400v 600v 800v s4x8es x 200 a to-92 s6x8es x 200 a to-92 s8x8es x 200 a to-92 s4x8ts x 200 a sot-223 s6x8ts x 200 a sot-223 s8x8ts x 200 a sot-223 s4x8bs x 200 a sot-89 s6x8bs x 200 a sot-89 s4x8es1 x 5 a to-92 S6X8ES1 x 5 a to-92 s8x8es1 x 5 a to-92 s4x8ts1 x 5 a sot-223 s6x8ts1 x 5 a sot-223 s8x8ts1 x 5 a sot-223 s4x8es2 x 50 a to-92 s6x8es2 x 50 a to-92 s8x8es2 x 50 a to-92 s4x8ts2 x 50 a sot-223 s6x8ts2 x 50 a sot-223 s8x8ts2 x 50 a sot-223 product selector 8 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series to-92 (3-lead) reel pack (rp) radial leaded specifcations meets all eia-468-c standards 0.708 (18.0) 1.6 (41.0) 0.5 (12.7) 0.1 (2.54) 0.2 (5.08) 0.236 (6.0) 0.02 (0.5) direction of feed dimensions are in inches (and millimeters). 1.97 (50.0) 14.17(360.0) flat up 1.26 (32.0) 0.098 (2.5) max cathode anode gate 0.354 (9.0) 0.157 dia (4.0) to-92 (3-lead) ammo pack (ap) radial leaded specifcations meets all eia-468-c standards flat down 25 devices per fold cathode anode gate direction of feed dimensions are in inches (and millimeters). 0.708 (18.0) 1.62 (41.2) 0.5 (12.7) 0.1 (2.54) 0.2 (5.08) 0.236 (6.0) 0.02 (0.5) 1.85 (47.0) 13.3 (338.0) 1.27 (32.2) 0.098 (2.5) max 12.2 (310.0) 1.85 (47.0) 0.354 (9.0) 0.157 dia (4.0) 9 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series sot-89 reel pack (rp1) specifcations 4mm 8mm 1.5mm 13 mm abor hole diameter 180 mm 13.4 mm 2mm 12mm anode gate anode 1.75mm 5.5mm direction of feed cathode sot-89 reel pack (rp) specifcations 4 mm 8 mm ?1.5 mm 13 mm abor hole diameter 180 mm 13.4 mm 2 mm 12 mm gate cathode anode anode 1.75 mm 5.5 mm direction of feed 10 revised: september 5, 2012 04:52 pm ?2012 littelfuse, inc specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. teccor ? brand thyristors ev series 0.8 amp sensitive scrs sxx8xsx series part numbering system current x8: 0.8a sensitivity & type s1: 5 a sensitive scr s2: 50 a sensitive scr s: 200 a sensitive scr package type e: to-92 t: sot-223 b: sot-89 packing type series s: scr blank: bulk pack rp: reel pack (to-92) embossed carrier pack (sot-223) embossed carrier pack (sot-89) rp1: embossed carrier pack (sot-89) (alternate orientation) ap: ammo pack (to-92) s xx8 voltage 4: 400v 6: 600v 8: 800v x xx xx part marking system sot-223 reel pack (rp) specifcations 4 mm 8 mm 1.5 mm 13 mm abor hole diameter 180 mm 13 .4 mm 2 mm 12 mm k gate a a 5.5 mm 1.75 mm line1 = littelfuse pa rt number line2 = continuation?littelfuse pa rt number y = last digit of calendar year m = l etter month co de (a-l for jan-dec) l = location co de dd = calendar date to92 sot89 sot223 |
Price & Availability of S6X8ES1
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |