![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
customer approval sheet customer approval sheet customer approval sheet customer approval sheet company name company name company name company name model model model model a080sn01 v5 customer customer customer customer approved approved approved approved title : name : approval for specifications only (spec. ver. approval for specifications only (spec. ver. approval for specifications only (spec. ver. approval for specifications only (spec. ver. ) ) ) ) approval for specifications and es sample (spec. ve r. approval for specifications and es sample (spec. ve r. approval for specifications and es sample (spec. ve r. approval for specifications and es sample (spec. ve r. ) ) ) ) approval for specifications and cs sample ( approval for specifications and cs sample ( approval for specifications and cs sample ( approval for specifications and cs sample (spec. ve r. spec. ver. spec. ver. spec. ver. ) ) ) ) customer remark : customer remark : customer remark : customer remark : auo pm : p/n : comment : www.datasheet.co.kr datasheet pdf - http://www..net/
all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. doc. version : 0.1 total pages : 35 date : 2009/02/11 product specification 8" color tft-lcd module model name a080sn01 v5 planned lifetime: from 2009/feb to 2011/feb phase-out control: from 2010/sep to 2011/feb eol schedule: 2011/feb < >preliminary specification < >final specification note: the content of this specification is subject to change. ? 2009 au optronics all rights reserved, do not copy. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 1/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. record of revision version revise date page content 0.0 2009/01/21 all first draft. 0.1 2009/02/11 4,5 update drawing 24 update chromaticity www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 2/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. contents a. general information ..................................... ................................................... .............................................3 b. outline dimension ...................................... ................................................... ..............................................4 1. tft-lcd module C front view.............................. ................................................... ...................................4 2. tft-lcd module C rear view ............................. ................................................... ....................................6 c. electrical specifications................................ ................................................... ...........................................7 1. tft lcd panel pin assignment.............................. ................................................... .................................7 2. backlight pin assignment .................................. ................................................... .......................................9 3. absolute maximum ratings.................................. ................................................... ....................................9 4. electrical dc characteristics......................... ................................................... .........................................10 5. electrical ac characteristics ......................... ................................................... .........................................13 6. serial interface characteristics ........................ ................................................... ......................................16 7. power on/off characteristics........................... ................................................... ......................................22 d. optical specification................................... ................................................... ............................................25 e. reliability test items................................... ................................................... ............................................28 f. packing and marking ...................................... ................................................... ........................................31 1. packing form .......................................... ................................................... ...............................................31 2. module/panel label information............................... ................................................... ..............................32 3. carton label information .................................. ................................................... ......................................32 g. application note..................................... ................................................... .................................................33 1. application circuit ................................. ................................................... ..................................................33 2. cabc function block.................................... ................................................... ...........................................34 h. precautions.......................................... ................................................... ................................................... .35 www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 3/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. a. general information this product is for portable dvd and digital photo frame application. no. item unit specification remark 1 screen size inch 8(diagonal) 2 display resolution dot 800rgb(w)x600(h) 3 overall dimension mm 183(w)x141(h)x6.3(d) note 1 4 active area mm 162(w)x121.5(h) 5 pixel pitch mm 0.2025(w)x0.2025(h) 6 color configuration -- r. g. b. stripe note 2 7 color depth -- 16.7m colors note 3 8 ntsc ratio % 50 9 display mode -- normally white 10 panel surface treatment -- anti-glare, 3h 11 weight g 188 10 12 panel power consumption mw 260 note 4 13 backlight power consumption w 1.87 viewing direction 6 oclock (gray inversion) note 1: not include blacklight cable and fpc. refer next page to get further information. note 2: below figure shows dot stripe arrangement. note 3: the full color display depends on 24-bit data signal (pin 4~27). note 4: please refer to electrical characteristics chapter. r g b r g b r g b r g b r g b . . ( 1 2 3. .. . 2398 2399 2400 ) ( 1 ... ..600 ) www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 4/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. b. outline dimension 1. tft-lcd module C front view www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 5/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 6/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. 2. tft-lcd module C rear view www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 7/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. c. electrical specifications 1. tft lcd panel pin assignment recommended connector : xf2m-6015-1ah pin no symbol i/o description remark 1 agnd p analog ground 2 avdd p analog power 3 vcc p digital power 4 r0 i data input (lsb) 5 r1 i data input 6 r2 i data input 7 r3 i data input 8 r4 i data input 9 r5 i data input 10 r6 i data input 11 r7 i data input (msb) 12 g0 i data input (lsb) 13 g1 i data input 14 g2 i data input 15 g3 i data input 16 g4 i data input 17 g5 i data input 18 g6 i data input 19 g7 i data input (msb) 20 b0 i data input (lsb) 21 b1 i data input 22 b2 i data input 23 b3 i data input 24 b4 i data input 25 b5 i data input 26 b6 i data input 27 b7 i data input (msb) 28 dclk i clock input 29 de i data enable signal 30 hsync i horizontal sync input. negative polarity 31 vsync i vertical sync input. negative polarity 32 scl i serial communication clock input 33 sda i serial communication data input www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 8/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 34 csb i serial communication chip select 35 nc - for test, do not connect (please leave it open) 36 vcc p digital power 37 nc - for test, do not connect (please leave it open) 38 gnd p digital ground 39 agnd p analog ground 40 avdd p analog power 41 vcomin i for external vcom dc input (optional) 42 dith/sda i/o dithering setting dith = "l" 6bit resolution(lsb last 2 bits of input data turncated) dith = "h" 8bit resolution(default setting) when register r14 and d7 is set to h. cabc enable. this pin would used as i 2 c data pin. 43 scl/gnd i/o when register r14 and d7 is set to h. cabc enable. this pin would used as i2c clock pin. (refer to section g2 C cabc function block) when register r14 and d7 is set to l, cabc is disable. this pin must connect to gnd. 44 vcom o connect a capacitor 45 v10 p gamma correction voltage reference 46 v9 p gamma correction voltage reference 47 v8 p gamma correction voltage reference 48 v7 p gamma correction voltage reference 49 v6 p gamma correction voltage reference 50 v5 p gamma correction voltage reference 51 v4 p gamma correction voltage reference 52 v3 p gamma correction voltage reference 53 v2 p gamma correction voltage reference 54 v1 p gamma correction voltage reference 55 nc/ led_cabc out o nc pin when register r14 and d7 is set to h. cabc enable. this pin would used as led pwm duty output. 56 vgh p positive power for tft 57 vcc p digital power 58 vgl p negative power for tft 59 gnd p digital ground 60 nc - nc pin i: input; p: power; g: ground; c: capacitor www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 9/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 2. backlight pin assignment recommended connector : h201k-p02n-02b (molex 51021-0200 compatible) pin no symbol i/o description remark 1 hi i power supply for backlight unit (high voltag e) 2 gnd - ground for backlight unit 3. absolute maximum ratings item symbol condition min. max. unit remark v cc gnd=0 -0.5 5 v av dd agnd=0 -0.5 15 v v gh -0.3 42 v v gl gnd=0 -20 0.3 v power voltage v gh v gl - 40 v v i -0.3 v cc +0.3 v note 1 input signal voltage vcom 0 6.5 v operating temperature topa -10 60 storage temperature tstg -20 70 note 1: hs , vs , de, digital data. note 2: functional operation should be restricted u nder ambient temperature (25 ). note 3: maximum ratings are those values beyond which damages to the device may occur. functional operation should be restricted to the limits in the electrical characteristics chapter. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 10/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 4. electrical dc characteristics a. (vcc = +3.3v, avdd=11.68v, agnd=gnd=0v, topr = -10 c to +60c) item symbol min. typ. max. unit remark v cc 2.7 3.3 3.6 v av dd 11 11.68 12 v v gh 14 15 16 v power supply v gl -7.5 -6.75 -5 v power consumption p - 230 260 mw black pattern vcom v cdc 3.4 3.6 3.8 v dc component h level v ih 0.7 v cc - v cc v input signal l level v il 0 - 0.3 v cc v note 1 input level of v1~v7 vx vcomdc - avdd-0.5 positive gamma correction voltage input level of v8~v14 vx 0.5 - vcomdc negative gamma correction voltage note 1: hs , vs , de, digital data www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 11/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. b. gamma voltage suggested circuit is as follows c.vcom buffer suggested circuit is as follows avdd avdd r325 0/5%/0603 3 4 2 5 1 + - u301a no(ad8565) 30k c324 10uf/10v/x5r/k/0805 r323 40k/5%/0603 r324 20k/5%/0603 c323 0.1uf/16v/x5r/k/0402 vr301 evm3rsx50b14 vcomin www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 12/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. d. current consumption (agnd=gnd=0v) parameter symbol condition min. typ. max. unit remark input current for vcc i vcc v cc =3.3v - 11 14 ma black pattern inpur current for avdd i avdd avdd=11.7v - 16 20 ma black pattern input current for vgh i vgh vgh=15v - 0.16 0.2 ma black pattern inpur current for vgl i vgl vgl=-6.75v - 0.16 0.2 ma black pattern e. backlight driving conditions parameter symbol min. typ. max. unit remark led lightbar current i l - 200 - ma note 1, 2 power consumption p - 2.08 - w led lightbar life time 10,000 - - hr note 1, 2, 3, 4 note 1: led backlight is led lightbar type(24 pcs of led). note 2: definition of led lifetime: brightness is decreased to 50% of t he initial value. led lifetime is restricted under normal condition, ambient temperature = 25 and led lightbar current= 200ma note 3: the value is only for reference. note 4: if it operates with led lightbar current mo re than 200ma, it maybe decreases led lifetime. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 13/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 5. electrical ac characteristics a. signal ac characteristics parameter symbol min. typ. max. unit. remark clock high time t wcl 8 - - ns clock low time t wch 8 - - ns hsync setup time t hsu 5 - - ns hsync hold time t hhd 10 - - ns vsync setup time t vsu 0 - - ns vsync hold time t vhd 2 - - ns data setup time t dsu 5 - - ns data hold time t dhd 10 - - ns data enable set - up time t esu 4 - - ns data enable hold time t ehd 2 - - ns b. input timing www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 14/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. c. input timing setting horizontal timing: parameter symbol min. typ. max. unit. remark dclk frequency f dclk 25 40 45 mhz dclk period t dclk 22 25 40 ns hsync period (= t hd + t hbl ) t h 986 1056 1183 dclk active area t hd - 800 - dclk horizontal blanking (= t hf + t he ) t h bl 186 256 383 dclk hsync front porch t hf - 40 - dclk delay from hsync to 1 st data input (= t hw + t hb ) t he 88 216 343 dclk function of hdl[7..0] settings hsync pulse width t hw 1 128 136 dclk hsync back porch t hb 10 88 342 dclk horizontal input timing (hv mode) horizontal input timing (de mode) www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 15/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. vertical timing: parameter symbol min. typ. max. unit. remark vsync period (= t vd + t vbl ) t v 620 628 635 th active lines t vd - 600 - vertical blanking (= t vf + t ve ) t vbl 20 28 35 th vsync front porch t vf - 1 - th gd start pulse delay t ve 19 27 34 hs function of vdl[3..0] settings vsync pulse width t vw 1 3 16 th hsync/vsync phase shift t vpd 2 320 - dclk vertical timing (hv mode) vertical timing (de mode) www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 16/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 6. serial interface characteristics a. serial control interface ac characteristic parameter symbol min. typ. max. unit. remark serial data setup time t ist 120 - - ns serial data hold time t ihd 120 - - ns csb setup time t cst 120 - - ns csb hold time t chd 120 - - ns serial clock high/low t ssw 120 - - ns serial clock t sck 320 - - ns delay from csb to vsync t cv 120 - - us chip select distinguish t cd 120 - - us serial data output delay t id - - 60 ns cl=20pf ac serial interface write mod e timings ac serial interface read mode timings www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 17/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. b. register bank there is a total of 6 registers each containing several paramete rs. for a detailed description of the parameters refer to register table. the serial register has read/write function. d[15:12] are the register address, d[11] defines the read or write mode and d[10:0] are the data. serial interface write/read sequence 1. at power-on, the default values specified for each parame ter are taken. 2. if less than 16-bit data are read during the cs low time period, the data is cancelled. a. the write operation is cancelled. b. the read operation is interrupt. 3. if more than 16-bit data are read during the cs low ti me period, the last 16 bits are kept. a. address & r/w are always defined form csb falling edge. b. the write operation load last 11 bit data before csb ri sing edge. c. the read operation is d0 is output to sda until csb rising edge. 4. all items are set at the falling edge of the vertical sync, except r0[1:0]. 5. when grb is activated through the serial interface, all registers are cleared, except the grb value. 6. register r/w setting: d11 = l write mode; d11 = h read mode. 7. the register setting values are valid when vcc already goe s to high and after vsync starts. 8. it is suggested that vsync, hsync, dclk always exists in the same time. but if hsync, dclk stops, only vsync operating, the register setting is still valid. 9. if the chip goes to standby mode, the register value will still keep. mcu can wake up the chip only by changing standby mode value from low to high. 10. the register setting values are rewritten by the influence of static electricity, a noise, etc. to unsuitable value, incorrect operating may occur. it is suggested that the spi interfa ce will setup as frequently as possible. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 18/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. c. serial interface setting table. reg address r/w data no. d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 (01) (01) dith (1) (0) (1) shdb1 (1) (0) grb (1) stb (1) r1 0 0 0 1 0 (0) (1) (6fh) r2 0 0 1 0 0 hdl (80h) r3 0 0 1 1 0 (0) (0) (0) (0) (0) vdl (1000) r4 0 1 0 0 0 (1) (0) (0) (0) (1) (1111) r6 0 1 1 0 0 (0) engb12 (1) engb11 (1) engb10 (1) (0) (0) engb5 (1) engb4 (1) engb3 (1) (0) r8 1 0 0 0 0 (0) (0) (0) (0) (1) (1) (1) (0) (1) cabc _en (0) r13 1 1 0 1 0 (1) (0) (0) (1) (1) (0) (0) (1) (0) (0) (0) r14 1 1 1 0 0 i2c_en (0) (1) (0) (1) (0) (0) (0) (0) x: reserved. please set to 0. d. register description r0 setting address bit description default 0000 [10..0] bits 10-9 auo internal use 01 bits7-8 auo internal use 01 bit6 (dith) dithering function. 1 bit5 auo internal use 0 bit4 auo internal use 1 bit3 (shdb1) avdd dc-dc converter shutdown setting. 1 bit2 auo internal use 0 bit1 (grb) global reset. 1 bit0 (stb) standby mode setting. 1 bit6 dith function 0 dith off. 1 dith on. (default) www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 19/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. bit3 shdb1 function 0 avdd dc-dc converter is off. 1 avdd dc-dc converter is on. (default) bit1 grb function 0 the controller is reset. reset all registers to de fault value. 1 normal operation. (default) bit0 stb function 0 t-con, source driver and dc-dcs converters are off. all outputs are set to gnd. 1 normal operation. (default) r2 setting address bit description default 0010 [7..0] bit7-0(hdl) horizontal start pulse adjustment function 80h bit7-0 hdl function 00h t he = t hetyp - 128 clk period. 80h t he = t hetyp . (default) ffh t he = t hetyp + 127 clk period. r3 setting address bit description default 0011 [8..0] bit8 auo internal use 0 bit7 auo internal use 0 bit6 auo internal use 0 bit5 auo internal use 0 bit4 auo internal use 0 bit3-0(vdl) vertical start pulse adjustment function 1000 www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 20/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. bit3-0 vdl function 0000 t ve = t vetyp C 8 hs period. 0001 t ve = t vetyp C 7 hs period. 0010 t ve = t vetyp C 6 hs period. 0011 t ve = t vetyp C 5 hs period. 0100 t ve = t vetyp C 4 hs period. 0101 t ve = t vetyp C 3 hs period. 0110 t ve = t vetyp C 2 hs period. 0111 t ve = t vetyp C 1 hs period. 1000 t ve = t vetyp. (default) 1001 t ve = t vetyp C 1 hs period. 1010 t ve = t vetyp C 2 hs period. 1011 t ve = t vetyp C 3 hs period. 1100 t ve = t vetyp C 4 hs period. 1101 t ve = t vetyp C 5 hs period. 1110 t ve = t vetyp C 6 hs period. 1111 t ve = t vetyp C 7 hs period. r6 setting address bit description default 0110 [9..0] bits9 auo internal use 0 bits8(engb12) gamma buffer enable for v9 1 bits7(engb11) gamma buffer enable for v8 1 bits6(engb10) gamma buffer enable for v7 1 bits5 auo internal use 0 bits4 auo internal use 0 bits3(engb5) gamma buffer enable for v4 1 bits2(engb4) gamma buffer enable for v3 1 bits1(engb3) gamma buffer enable for v2 1 bits0 auo internal use 0 bitx engbx function 0 gamma buffer for vx is disabled (high z). 1 gamma buffer is enabled. vx must be connected externally. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 21/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. r8 setting address bit description default 1000 [1] bit0 cabc function enable 0: cabc function is disabled. (default) 1: cabc function is enabled. 0 r14 setting address bit description default 1000 [1] bit7 cabc 2-wire serial interface is enabled. 0: 2-wire serial interface is disabled. (default) 1: 2-wire serial interface is enabled. 0 www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 22/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 7. power on/off characteristics a.1 recommended power on register setting (without cabc) address r/w data reg no . d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 10 01 1 0 1 0 0 1 1 r1 0 0 0 1 0 0 01 01 2fh r2 0 0 1 0 0 0 0 0 80h r3 0 0 1 1 0 0 0 0 0 0 0 0 1000 r4 0 1 0 0 0 0 0 1 1 00 1 1111 r6 0 1 1 0 0 0 0 1 1 1 0 0 1 1 1 0 a.2 recommended power on register setting (with cabc) address r/w data reg no . d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 10 01 1 0 1 0 0 1 1 r1 0 0 0 1 0 0 01 01 2fh r2 0 0 1 0 0 0 0 0 80h r3 0 0 1 1 0 0 0 0 0 0 0 0 1000 r4 0 1 0 0 0 0 0 1 1 00 1 1111 r6 0 1 1 0 0 0 0 1 1 1 0 0 1 1 1 0 r13 1 1 0 1 0 1 0 0 1 1 1 1 0 1 0 0 r14 1 1 1 0 0 1 1 0 1 0 0 0 0 r8 1 0 0 0 0 0 0 0 0 1 1 1 0 1 1 note : start to provide spi commend at least after 2 frame. 1. send r15 : 000h(normal register bank) at first. 2. wait at least after more than one frame, send r0 : 4d1h(global reset) 3. after send global reset, start to send r0 to r14 recommend register valu e. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 23/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. b. recommended power on sequence www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 24/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. c. power off sequence www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 25/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. d. optical specification all optical specification is measured under typical condition (note 1, 2) item symbol condition min. typ. max. unit remark response time rise fall tr tf =0 -- -- 4 16 8 32 ms ms note 3 contrast ratio cr at optimized viewing angle 400 500 -- note 4 top bottom left viewing angle right cr R 10 50 50 60 60 60 65 70 70 deg. note 5 brightness y l =0 220 250 -- cd/m 2 note 6 x =0 0.26 0.31 0.36 white y =0 0.28 0.33 0.38 x =0 0.52 0.57 0.62 red y =0 0.32 0.37 0.42 x =0 0.30 0.35 0.40 green y =0 0.53 0.58 0.63 x =0 0.10 0.15 0.20 chromaticity blue y =0 0.06 0.11 0.16 uniformity y l % 70 75 -- % note 7 note 1: ambient temperature =25 , and led lightbar currently i l = 200ma. to be measured in the dark room. note 2: to be measured on the center area of panel with a viewing cone of 1 by topcon luminance meter bm-5a, after 15 minutes operation. center of the screen field=1 bm-5a www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 26/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 3: definition of response time: the output signals of photo detector are measured wh en the input signals are changed from black to white(falling time) and from white to black(rising time), respectively. the response time is defined as the time interval be tween the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% note 4.definition of contrast ratio: contrast ratio is calculated with the following fo rmula. status black" " at is lcd when output detector photo status white" " at is lcd when output detector photo (cr) ratio contrast = note 5. definition of viewing angle, , refer to figure as below. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 27/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 6. measured at the center area of the panel whe n all the input terminals of lcd panel are electrica lly opened. note 7: luminance uniformity of these 9 points is d efined as below: 9) - (1 points 9 in luminance maximum 9) - (1 points 9 in luminance minimum uniformity = www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 28/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. e. reliability test items no. test items conditions remark 1 high temperature storage ta= 70 240hrs 2 low temperature storage ta= -20 240hrs 3 high ttemperature operation tp= 60 240hrs 4 low temperature operation ta= -10 240hrs 5 high temperature & high humidity tp= 50 . 80% rh 240hrs operation 6 heat shock -10 ~ 60 , 100 cycle, 1hrs/cycle non-operation 7 electrostatic discharge contact = 4 kv, class b air = 8 kv, class b note 4 8 image sticking 25 , 4hrs note 5 frequency range : 10~55hz stoke : 1.5mm sweep : 10 ~ 55 ~ 10hz 2 hours for each direction of x,y,z 9 vibration (6 hours for total) non-operation jis c7021, a-10 condition a : 15 minutes 10 mechanical shock 100g . 6ms, x,y,z 3 times for each direction non-operation jis c7021, a-7 condition c 11 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz C6db/octave from 200~500hz iec 68-34 12 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces 13 pressure 5kg, 5sec note 6 note 1: ta: ambient temperature. tp: panel surface temp erature note 2: in the standard conditions, there is not di splay function ng issue occurred. all the cosmetic specification is judged before the reliability stre ss. note 3: all the cosmetic specification is judged be fore the reliability stress. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 29/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note4 : all test techniques follow iec6100-4-2 stan dard. test condition note pattern procedure and set-up contact discharge 330?, 150pf, 1sec, 8 point, 25times/point air discharge 330?, 150pf, 1sec, 8 point, 25times/point criteria b C some performance degradation allowed. no data lost. self-recoverable hardware failure. others 1. gun to panel distance 2. no spi command, keep default register settings. note 5: operate with 55 chess board pattern as figure and lasting time and tem perature as the conditions. then judge with 50% gray level after wa iting 20 min, the mura is less than jnd 2.5. note 6: the panel is tested as figure. the jig is 10 mm made by cu with rubber and the loading speed is 3mm/min on position a~e. after the condition, no glass crack will be found and panel function check is ok.( no guarantee lc mura lc bubble) www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 30/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. loading lcm www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 31/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. f. packing and marking 1. packing form www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 32/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. module/panel label information the module/panel (collectively called as the product) will be attached wi th a label of shipping number which represents the identification of the product at a specific locatio n. refer to the product outline drawing for detailed location and size of the label. the label is composed of a 22-digit serial number and printed with code 39/128 with the following definition: 3. carton label information the packing carton will be attached with a carton label where packing qty, auo model name, auo part number, customer part number (optional) and a series of carton number in 13 or 14 digits are printed. the carton number is apparing in the following format: refer to the drawing of packing format for the location and size of the carton lab el. www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 33/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. g. application note 1. application circuit www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 34/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. cabc function block www.datasheet.co.kr datasheet pdf - http://www..net/ version: 0.1 page: 35/35 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. h. precautions 1. do not twist or bend the module and prevent the unsuitable external force for displ ay module during assembly. 2. adopt measures for good heat radiation. be sure to use the module with in the speci fied temperature. 3. avoid dust or oil mist during assembly. 4. follow the correct power sequence while operating. do not apply the inval id signal, otherwise, it will cause improper shut down and damage the module. 5. less emi: it will be more safety and less noise. 6. please operate module in suitable temperature. the response time & brightness will dri ft by different temperature. 7. avoid to display the fixed pattern (exclude the white pattern) in a long period, otherwise, it will cause image sticking. 8. be sure to turn off the power when connecting or disconnecting the circuit . 9. polarizer scratches easily, please handle it carefully. 10. display surface never likes dirt or stains. 11. a dewdrop may lead to destruction. please wipe off any moisture before usi ng module. 12. sudden temperature changes cause condensation, and it will cause polarizer damaged. 13. high temperature and humidity may degrade performance. please do not expose the module to t he direct sunlight and so on. 14. acetic acid or chlorine compounds are not friends with tft display module. 15. static electricity will damage the module, please do not touch the module wit hout any grounded device. 16. do not disassemble and reassemble the module by self. 17. be careful do not touch the rear side directly. 18. no strong vibration or shock. it will cause module broken. 19. storage the modules in suitable environment with regular packing. 20. be careful of injury from a broken display module. 21. please avoid the pressure adding to the surface (front or rear side) of modul es, because it will cause the display non-uniformity or other function issue. www.datasheet.co.kr datasheet pdf - http://www..net/ |
Price & Availability of A080SN01-V5
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |