View B140EW01-V3_3665685.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 1/27 version: 0 date: 2005/5/2 product functional specification 14.0 inch wxga color tft lcd module model name: b140ew01 v.3 --- rohs compliance ( ) preliminary specification ( u ) final specification note: this specification is subject to change without notice. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 2/27 contents 1.0 handling precautions......................................................................................................................4 2.0 general description..........................................................................................................................5 2.1 display characteristics..............................................................................................................................................5 2.2 functional block diagram.........................................................................................................................................6 3.0 absolute maximum ratings.............................................................................................................7 4.0 optical characteristics.....................................................................................................................8 5.0 signal interface...............................................................................................................................10 5.1 connectors..............................................................................................................................................................10 5.2 signal pin...............................................................................................................................................................10 5.3 signal description...................................................................................................................................................11 5.4 signal electrical characteristics..............................................................................................................................12 5.5 signal for lamp connector......................................................................................................................................12 6.0 pixel format image.........................................................................................................................14 7.0 parameter guide line for ccfl inverter........................................................................................14 8.0 interface timings............................................................................................................................15 8.1 timing characteristics............................................................................................................................................15 8.2 timing definition...................................................................................................................................................16 9.0 power consumption........................................................................................................................17 10. power on/off sequence...............................................................................................................18 11.0 reliability /safety requirement....................................................................................................19 11.1 reliability test conditions....................................................................................................................................19 11.2 safety....................................................................................................................................................................19 12.0 packing dimension......................................................................................................................20 13.0 mechanical characteristics...........................................................................................................21 13.1 lcm outline dimension (front view)...................................................................................................................21 13.2 lcm outline dimension (rear view)...................................................................................................................22 13.3 screw hole depth and center position..................................................................................................................23 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 3/27 ii record of revision version and date page old description new description remark v.0 2005/05/02 all first release na www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 4/27 1.0 handling precautions 1) do not press or scratch the surface harder than a hb pencil lead because the polarizers are very fragile and could be easily damaged. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water droplets or oil immediately. long contact with the droplets may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) protect the module from static electricity and insure proper grounding when handling. static electricity may cause damage to the cmos gate array ic. 7) do not disassemble the module. 8) do not press the reflector sheet at the back of the module. 9) avoid damaging the tft module. do not press the center of the ccfl reflector when it was taken out from the packing container. instead, press at the edge of the ccfl reflector softly. 10) do not rotate or tilt the signal interface connector of the tft module when you insert or remove other connector into the signal interface connector. 11) do not twist or bend the tft module when installation of the tft module into an enclosure (notebook pc bezel, for example). it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside when designing the enclosure. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local regulations for disposal. 13) the lcd module contains a small amount of material that has no flammability grade, so it should be supplied by power complied with requirements of limited power source (2.11, iec60950 or ul1950). 14) the ccfl in the lcd module is supplied with limited current circuit (2.4, iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 5/27 2.0 general description this specification applies to the 14.0 inch color tft/lcd module b140ew01 this module is designed for a display unit of notebook style personal computer. the screen format is intended to support the wxga (1280(h) x 768(v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. this module does not contain an inverter card for backlight. 2 2 . . 1 1 d d i i s s p p l l a a y y c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 355.6 (14.0") active area [mm] 305.28(h) x 183.17(v) pixels h x v 1280(x3) x 768 pixel pitch [mm] 0.2385 pixel arrangement r.g.b. vertical stripe display mode normally white typical white luminance (ccfl=6.0ma) [cd/m 2 ] 200 typ.(5 points average) contrast ratio 250 : 1 min ,300:1 typ response time [msec] 25 typ. nominal input voltage vdd [volt] +3.3 typ. typical power consumption (vdd line + vcfl line) [watt] 5.8 watt (w/o inverter)@ lcm circuit 1.6 watt (typ.), b/l input 4.2 watt (typ.) weight [grams] 440g typ. (w/o inverter) physical size [mm] 320(w) x 199(h) x 5.7(d) max. electrical interface r/g/b data, 3 sync, signals, clock (4 pairs lvds) support color native 262k colors (rgb 6-bit data driver) surface treatment haze 25, hard coating 3h,ag temperature range operating storage (shipping) [ o c] [ o c] 0 to +50 -20 to +60 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 6/27 2 2 . . 2 2 f f u u n n c c t t i i o o n n a a l l b b l l o o c c k k d d i i a a g g r r a a m m the following diagram shows the functional block of the 14.0 inches color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1280(r/g/b) x 3 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) jae fi-xb30s-hf10 mating contactfi-xc3-1-15000 mating housing jae fi-x30h jst bhsr-02vs- 1 mating type sm02b-bhss-1- tb lamp connector(2pin) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 7/27 3.0 absolute maximum ratings absolute maximum ratings of the module is as following: item symbol min max unit conditions logic/lcd drive voltage vdd -0.3 +4.0 [volt] input voltage of signal vin -0.3 vdd+0.3 [volt] ccfl current icfl 2.5 7 [ma] rms ccfl ignition voltage vs ? 1200 vrms note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 5 95 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 5 95 [%rh] note 2 vibration 1.5sin 10-500 [g hz] shock 240, 2 [g ms] half sine wave note 1: duration = 50msec note 2: maximum wet-bulb should be 39 and no condensation. wet bulb temperature chart twb=39 c operating range www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 8/27 storage range 4.0 optical characteristics the optical characteristics are measured under stable conditions as follows under 25 condition: item unit conditions min. typ. max. note horizontal (right) 40 45 - (left) 40 45 - vertical (upper) 15 20 - viewing angle (cr = 10) cr: contrast ratio [degrees] (lower) 30 35 - 5 points - 1.2 (1) uniformity 13 points - 1.5 (2) contrast ratio (center) 250 300 - rising - 15 20 response time [msec] falling - 10 15 red x 0.560 0.590 0.620 red y 0.300 0.330 0.360 green x 0.290 0.320 0.350 green y 0.510 0.540 0.570 blue x 0.120 0.150 0.180 blue y 0.100 0.130 0.160 white x 0.283 0.313 0.343 color chromaticity coordinates (cie) (normal view angle) white y 0.299 0.329 0.359 white luminance ( ccfl 6.0ma ) [cd/m 2 ] 5 points average -- 200 - (1) cross talk % -- --- 1.4 (3) note (1): 5 points position (display area: 305.28 mm x 183.17 mm) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 9/27 12 3 45 h/4 h/4 h/4 h/4 h w w/4 w/4 w/4 w/4 note (2): 13 points position w/4 w w/4 h h/4 h/4 h/4 h/4 7 9 10 w/4 1 8 w/4 10 10 10 10 2 3 13 12 45 6 11 note (3): definition of cross talk (d ct ) d ct = | y b C y a | / y a 100 (%) y a ,y b = (511,127) or (170,383) or (853,383) or (511,639) where : y a = luminance of measured location without darkest gray pattern (cd/m 2 ) y b = luminance of measured location with darkest gray pattern (cd/m 2 ) yb ya view area (1023, 767) (0, 0) gray level 63 view area (1023, 767) (0, 0) gray level 63 gray level 0 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 10/27 5.0 signal interface 5 5 . . 1 1 c c o o n n n n e e c c t t o o r r s s physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for signal connector manufacturer jae type / part number fi-xb30s-hf10 mating housing/part number fi-x30h mating contact/part number fi-xc3-1-15000 connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 5 5 . . 2 2 s s i i g g n n a a l l p p i i n n pin# signal name pin# signal name 1 gnd 2 vdd 3 vdd 4 v edid 5 nc 6 clk edid 7 data edid 8 rxin0- 9 rxin0+ 10 gnd 11 rxin1- 12 rxin1+ 13 gnd 14 rxin2- 15 rxin2+ 16 gnd 17 rxclkin- 18 rxclkin+ 19 gnd 20 nc 21 nc 22 gnd 23 nc 24 nc 25 gnd 26 nc 27 nc 28 gnd 29 nc 30 nc www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 11/27 5 5 . . 3 3 s s i i g g n n a a l l d d e e s s c c r r i i p p t t i i o o n n the module uses a lvds receiver embedded in auo s asic. lvds is a differential signal technology for lcd interface and high-speed data transfer device. signal name description v edid +3.3v edid power clk edid edid clock input data edid edid data input rxin0-, rxin0+ lvds differential data input(red0-red5, green0) rxin1-, rxin1+ lvds differential data input(green1-green5, blue0-blue1) rxin2-, rxin2+ lvds differential data input(blue2-blue5, hsync, vsync, dsptmg) rxclkin-, rxclkin0+ lvds differential clock input vdd +3.3v power supply gnd ground note : input signals shall be in low status when vdd is off. internal circuit of lvds inputs are as following. signal name description +red5 +red4 +red3 +red2 +red1 +red0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) (red-pixel data) red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. +green 5 +green 4 +green 3 +green 2 +green 1 +green 0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) (green-pixel data) green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. +blue 5 +blue 4 +blue 3 +blue 2 +blue 1 +blue 0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) (blue-pixel data) blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. -dtclk data clock the typical frequency is 71.1 mhz. the signal is used to strobe the pixel data and dsptmg signals. all pixel data shall be valid at the falling edge when the dsptmg signal is high. dsptmg display timing this signal is stored at the falling edge of -dtclk. when the signal is high, the pixel data shall be valid to be displayed. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 12/27 vsync vertical sync the signal is synchronized to -dtclk . hsync horizontal sync the signal is synchronized to -dtclk . note: output signals from any system shall be low or hi-z state when vdd is off. 5 5 . . 4 4 s s i i g g n n a a l l e e l l e e c c t t r r i i c c a a l l c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s input signals shall be in low status when vdd is off. it is recommended to refer the specifications of sn75lvds86dgg (texas instruments) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high voltage(vcm=+1.2v) ? 100 [mv] vtl differential input low voltage(vcm=+1.2v) -100 ? [mv] lvds macro ac characteristics are as follows: min. max. clock frequency (f) 60.7mhz 85mhz data setup time (tsu) 600ps data hold time (thd) 600ps 5 5 . . 5 5 s s i i g g n n a a l l f f o o r r l l a a m m p p c c o o n n n n e e c c t t o o r r pin # signal name 1 lamp high voltage thd tsu input clock input data t f www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 13/27 2 lamp low voltage www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 14/27 6.0 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1278 1279 1st line 768th line 7.0 parameter guide line for ccfl inverter parameter min dp-1 max units condition white luminance 5 points average 170 200 ? [cd/m 2 ] (ta=25 ) ccfl current (icfl) 2.5 6.0 7.0 [ma] rms (ta=25 ) (note 2) ccfl frequency (fcfl) 50 60 65 [khz] (ta=25 ) (note 3) ccfl ignition voltage (vs) ? 1000 1200 [volt] rms (ta= 25 ) (note 4) ccfl voltage (reference) (vcfl) ? 650 ? [volt] rms (ta=25 ) (note 5) ccfl power consumption (pcfl) ? 4.2 ? [watt] (ta=25 ) (note 5) note 1 : dp-1 are auo recommended design points. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 15/27 *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit ver carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when ccfl is damaged. *4 generally, ccfl has some amount of delay time after applying start-up voltage. it is recommended to keep on applying start-up voltage for 1 [sec] until discharge. *5 the ccfl inverter operating frequency must be carefully chosen so that no interfering noise stripes on the screen were induced. *6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2 : it should be employed the inverter, which has duty dimming , if iccfl is less than 4ma. note 3 : the ccfl inverter operating frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the inverter open voltage should be designed larger than the lamp starting voltage at t=0 o c, otherwise backlight may be blinking for a moment after turning on or not be able to turn on. the open voltage should be measured after ballast capacitor. if an inverter has shutdown function it should keep its open voltage. for longer than 1 second even if lamp connector is open. note 5 : calculator value for reference (icfl vcfl=pcfl) 8.0 interface timings basically, interface timings should match the vesa 1024x768 /60hz (vg901101) manufacturing guide line timing. 8 8 . . 1 1 t t i i m m i i n n g g c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s symbol description min typ max unit dotclk dotclk frequency (tbd) 71.1 (tbd) [mhz] t clock dotclk cycle time (tbd) 14.06 (tbd) [nsec] t h x total time ? 1440 ? [tck] t hd x active time ? 1280 ? [tck] t hb x blank time ? 160 ? [tck] t v y total time ? 823 ? [tx] t vd y active time ? 768 ? [tx] vsync frame rate ? 60 ? [hz] note: de mode www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 16/27 8 8 . . 2 2 t t i i m m i i n n g g d d e e f f i i n n i i t t i i o o n n dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 17/27 9.0 power consumption input power specifications are as follows; symbol parameter min typ max units condition module vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] load capacitance 20uf pdd vdd power ? 1.6 ? [watt] pdd max vdd power max ? (tbd) ? [watt] max pattern (note) idd idd current ? (tbd) ? ma 64 grayscale pattern idd max idd current max ? (tbd) ? ma vertical stripe line pattern (note) vddrp allowable logic/lcd drive ripple voltage ? ? 100 [mv] p-p vddns allowable logic/lcd drive ripple noise ? ? 100 [mv] p-p lamp icfl ccfl current 2.5 6.0 7.0 [ma] rms (ta=25 ) vcfl ccfl voltage (reference) ? 650 ? [volt] rms (ta=25 ) pcfl ccfl power consumption ? 4.2 ? [watt] (ta=25 ) total power consumption 5.8 watt (w/o inverter,)@lcm circuit 1.6 watt (typ.),b/l input 4.2 watt(typ.) note: vdd=3.3v www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 18/27 10. power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. sequence of power-on/off and signal-on/off power supply vdd lvds interface backlight on apply the lamp voltage within the lcd operating range. when the backlight turns on before the lcd operation or the lcd turns off before the backlight turns off, the display may momentarily become abnormal. 0ms (c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 19/27 11.0 reliability /safety requirement 1 1 1 1 . . 1 1 r r e e l l i i a a b b i i l l i i t t y y t t e e s s t t c c o o n n d d i i t t i i o o n n s s items required condition temperature humidity bias 40 /90%,300hr high temperature operation 50 /dry,300hr low temperature operation 0 ,500hr continuous life 25 ,2000 hours on/off test on/30 sec. off/30sec., 30,000 cycles hot storage 60 /40% rh ,240 hours cold storage -20 /50% rh ,240 hours thermal shock test -20 /30 min ,60 /30 min 100cycles hot start test 50 /1 hr min. power on/off per 5 minutes, 5 times cold start test 0 /1 hr min. power on/off per 5 minutes, 5 times shock test (non-operating) 240g, 2ms, half-sine wave vibration test (non-operating) sinusoidal vibration, 1.5g zero-to- peak, 10 to 500 hz, 0.5 octave/minute in each of three mutually perpendicular axes. esd contact : operation 8kv / non-operation 10kv air : operation 15kv / non-operation 20kv altitude test 10000 ft / operation / 8hr 30000 ft / non-operation / 24r maximum side mount torque 2.5 kgf.cm . ccfl life: 10,000 hours minimum mtbf(excluding the ccfl) : 30,000 hours with a confidence level 90% 1 1 1 1 . . 2 2 s s a a f f e e t t y y ul1950 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 20/27 12.0 packing dimension carton use 14" cushion side cushion top paper pad for mark "h" taping close carton label position esd bag 14.0" panel 14.0" panel * 20 pcs www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 21/27 13.0 mechanical characteristics 1 1 3 3 . . 1 1 l l c c m m o o u u t t l l i i n n e e d d i i m m e e n n s s i i o o n n ( ( f f r r o o n n t t v v i i e e w w ) ) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 22/27 1 1 3 3 . . 2 2 l l c c m m o o u u t t l l i i n n e e d d i i m m e e n n s s i i o o n n ( ( r r e e a a r r v v i i e e w w ) ) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 23/27 1 1 3 3 . . 3 3 s s c c r r e e w w h h o o l l e e d d e e p p t t h h a a n n d d c c e e n n t t e e r r p p o o s s i i t t i i o o n n screw hole maximum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 3.1 0.1mm (see drawing) suggestions: customers screw maximum length = 2.3 mm (see drawing) screw torque: maximum2.5 kgf-cm www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 24/27 14.0 edid data address function value value value hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code 33 00110011 51 0b hex, lsb first 13 00010011 19 0c 32 - bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 0f 00001111 15 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input definition 80 10000000 128 15 max h image size 21 00100001 33 16 max v image size 14 00010100 20 17 display gamma 78 01111000 120 18 feature support 0a 00001010 10 19 red/green low bits 05 00000101 5 1a blue/white low bits 50 01010000 80 1b red x/ high bits 97 10010111 151 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 25/27 1c red y 57 01010111 87 1d green x 4f 01001111 79 1e green y 8f 10001111 143 1f blue x 26 00100110 38 20 blue y 21 00100001 33 21 white x 50 01010000 80 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 manufacturer's timing 00 00000000 0 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10,000 (lsb) c6 11000110 198 37 pixel clock/10,000 (msb) 1b 00011011 27 38 horiz. active pixels(lower 8 bits) 00 00000000 0 39 horiz.blanking (lower 8 bits) a0 10100000 160 3a horiz. active pixels:horiz. blanking (upper4:4 bits) 50 01010000 80 3b 00 00000000 0 3c 37 00110111 55 3d vert. active pixels:vert. blanking (upper4:4 bits) 30 00110000 48 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 26/27 3e 10 00010000 16 3f 70 01110000 112 40 vert. sync. offset=xx lines, sync width=xx lines 13 00010011 19 41 horz. ver. sync/width (upper 2 bits) 00 00000000 0 42 hori. image size (lower 8 bits) 31 00110001 49 43 vert. image size (lower 8 bits) b7 10110111 183 44 hori. image size : vert. image size (upper 4 bits) 10 00010000 16 45 00 00000000 0 46 00 00000000 0 47 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 0 0000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f 41 01000001 65 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics dec., 2003 all rights reserved. b140ew01 v.3 no reproduction and redistribution allowed. 27/27 60 55 01010101 85 61 4f 01001111 79 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 42 01000010 66 72 31 00110001 49 73 34 00110100 52 74 30 00110000 48 75 45 01000101 69 76 57 01010111 87 77 30 00110000 48 78 31 00110001 49 79 20 00100000 32 7a 56 01010110 86 7b 33 00110011 51 7c 20 00100000 32 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum e8 11101000 232 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of B140EW01-V3

	To Download B140EW01-V3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .