? semiconductor components industries, llc, 2002 august, 2002 rev. 1 1 publication order number: nl17szu04/d nl17szu04 single unbuffered inverter the nl17szu04 is a single unbuffered inverter in a tiny footprint package. the sc70/sc88a occupies a very small board area. the device performs much as lcx multigate products in speed and drive. ? tiny sc70/sc88a package ? source/sink 16 ma at 4.5 v v cc ? overvoltage tolerant inputs and outputs ? pin for pin with nc7szu04 ? chip complexity: fets = l6 ? designed for 1.65 v to 5.5 v v cc operation figure 1. pinout (top view) figure 2. logic symbol 1 a y v cc nc a 1 2 3 5 4 gnd y pin assignment pin 1 2 3 4 5 function nc a gnd y v cc input function table output y = a y h l a l h see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information marking diagrams pin 1 d = date code l6 d sc705/sc88a/sot353 df suffix case 419a 1 5 http://onsemi.com
nl17szu04 http://onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage 0.5 to 7.0 v v in dc input voltage 0.5 to 7.0 v v out dc output voltage 0.5 to 7.0 v i ik dc input diode current 50 ma i ok dc output diode current 50 ma i out dc output sink current 50 ma i cc dc supply current per supply pin 100 ma t stg storage temperature range 65 to 150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c ja thermal resistance sc70/sc88a (note 1) tsop5 350 230 c/w p d power dissipation in still air at 85 c sc70/sc88a tsop5 150 200 mw msl moisture sensitivity level 1 f r flammability rating oxygen index: 28 to 34 ul 94 v0 @ 0.125 in v esd esd withstand voltage human body model (note 2) machine model (note 3) charged device model (note 4) 2000 200 n/a v maximum ratings are those values beyond which damage to the device may occur. exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. functional operation under absolute maximumrated conditions is not implied. functional operation should be restricted to the recommended operating conditions. 1. measured with minimum pad spacing on an fr4 board, using 10 mmby1 inch, 2ounce copper trace with no air flow. 2. tested to eia/jesd22a114a. 3. tested to eia/jesd22a115a. 4. tested to jesd22c101a. recommended operating conditions symbol parameter min max unit v cc dc supply voltage (operating) data retention only 1.65 1.5 5.5 5.5 v v in dc input voltage 0 5.5 v v out dc output voltage 0 5.5 v t a operating temperature range 40 +85 c t r , t f input rise and fall time v cc = 3.0 v 0.3 v v cc = 5.0 v 0.5 v 0 0 100 20 ns/v device junction temperature versus time to 0.1% bond failures junction temperature c time, hours time, years 80 1,032,200 117.8 90 419,300 47.9 100 178,700 20.4 110 79,600 9.4 120 37,000 4.2 130 17,800 2.0 140 8,900 1.0 1 1 10 100 1000 failure rate of plastic = ceramic until intermetallics occur figure 3. failure rate vs. time junction temperature normalized failure rate time, years t j = 130 c t j = 120 c t j = 110 c t j = 100 c t j = 90 c t j = 80 c
nl17szu04 http://onsemi.com 3 dc electrical characteristics v cc t a = 25 c 40 c t a 85 c symbol parameter condition v cc (v) min typ max min max unit v ih highlevel input voltage 1.65 to 1.85 0.85 v cc 0.85 v cc v 2.3 to 5.5 0.8 v cc 0.8 v cc v il lowlevel input voltage 1.65 to 1.85 0.15 v cc 0.15 v cc v 2.3 to 5.5 0.2 v cc 0.2 v cc v oh highlevel output voltage v in = v il or v ih i oh = 100 a i oh = 3 ma 1.65 to 5.5 1.65 v cc 0.1 1.29 v cc 1.52 v cc 0.1 1.29 v v in = v il or v ih i oh = 4 ma 2.3 1.9 2.1 1.9 i oh = 6 ma 2.7 2.2 2.4 2.2 i oh = 8 ma 3.0 2.4 2.7 2.4 i oh = 12 ma 3.0 2.3 2.5 2.3 i oh = 16 ma 4.5 3.8 4.0 3.8 v ol lowlevel output voltage v in = v ih or v oh i ol = 100 a i ol = 3 ma 1.65 to 5.5 1.65 0.08 0.1 0.24 0.1 0.24 v v in = v ih or v oh i ol = 4 ma 2.3 0.20 0.3 0.3 i ol = 6 ma 2.7 0.22 0.4 0.4 i ol = 8 ma 3.0 0.28 0.4 0.4 i ol = 12 ma 3.0 0.38 0.55 0.55 i ol = 16 ma 4.5 0.42 0.55 0.55 i in input leakage current v in = v cc or gnd 0 to 5.5 0.1 1.0 a i off power offoutput leakage current v out = 5.5 v 0 1 10 a i cc quiescent supply current v in = v cc or gnd 1.65 to 5.5 1 10 a ac electrical characteristics t r = t f = 3.0 ns v cc t a = 25 c 40 c t a 85 c symbol parameter condition v cc (v) min max min max unit t plh propagation delay (fi d ) r l = 1 m c l = 15 pf 1.8 0.15 1.0 11.7 1.0 12.1 ns t phl (figure 4 and 5) r l = 1 m c l = 15 pf 2.5 0.2 0.8 6.2 0.8 6.5 r l = 1 m c l = 15 pf 3.3 0.3 0.5 4.5 0.5 4.8 r l = 500 c l = 50 pf 1.0 6.0 1.0 6.5 r l = 1 m c l = 15 pf 5.0 0.5 0.5 3.9 0.5 1.0 r l = 500 c l = 50 pf 0.8 5.0 0.8 5.5 capacitive characteristics symbol parameter condition typical unit c in input capacitance v cc = 5.5 v, v i = 0 v or v cc 4.5 pf c pd power dissipation capacitance () 10 mhz, v cc = 3.3 v, v i = 0 v or v cc 6.5 pf (note 5) 10 mhz, v cc = 5.5 v, v i = 0 v or v cc 10 5. c pd is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption with out load. average operating current can be obtained by the equation: i cc(opr ) = c pd v cc f in + i cc . c pd is used to determine the noload dynamic power consumption; p d = c pd v cc 2 f in + i cc v cc .
nl17szu04 http://onsemi.com 4 figure 4. switching waveform input r l c l a 1mhz square input wave is recommended for propagation delay tests. figure 5. test circuit t f = 3 ns v cc gnd v oh v ol 90% 50% 10% 50% t plh t phl output y input a and b t f = 3 ns 90% 50% 10% 50% output device ordering information device nomenclature device order number logic circuit indicator no. of gates per package temp range identifier technology device function package suffix tape and reel suffix package type tape and reel size nl17szu04dft2 nl 1 7 sz u04 df t2 sc88a/ sot353/ sc705 178 mm, 3000 unit
nl17szu04 http://onsemi.com 5 tape trailer (connected to reel hub) no components 160 mm min tape leader no components 400 mm min components direction of feed cavity tape top tape figure 6. tape ends for finished goods 1 4.00 2.00 1.75 1.00 min 4.00 figure 7. sc70/sc88a/sot353 dft2 reel configuration/orientation direction of feed tape dimensions mm 1.50 typ 8.00 0.30 3.50 0.50
nl17szu04 http://onsemi.com 6 figure 8. reel dimensions 13.0 mm 0.2 mm (0.512 in 0.008 in) 1.5 mm min (0.06 in) 50 mm min (1.969 in) 20.2 mm min (0.795 in) full radius t max g a reel dimensions tape size 8 mm t and r suffix t1, t2 a max 178 mm (7 in) g 8.4 mm, + 1.5 mm, 0.0 (0.33 in + 0.059 in, 0.00) t max 14.4 mm (0.56 in) figure 9. reel winding direction direction of feed barcode label hole pocket
nl17szu04 http://onsemi.com 7 package dimensions sc705/sc88a/sot353 df suffix 5lead package case 419a01 issue f 0.5 mm (min) 0.4 mm (min) 0.65 mm 0.65 mm 1.9 mm notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. 419a-01 obsolete. new standard 419a-02. dim a min max min max millimeters 1.80 2.20 0.071 0.087 inches b 1.15 1.35 0.045 0.053 c 0.80 1.10 0.031 0.043 d 0.10 0.30 0.004 0.012 g 0.65 bsc 0.026 bsc h --- 0.10 --- 0.004 j 0.10 0.25 0.004 0.010 k 0.10 0.30 0.004 0.012 n 0.20 ref 0.008 ref s 2.00 2.20 0.079 0.087 b 0.2 (0.008) mm 12 3 4 5 a g s d 5 pl h c n j k b
nl17szu04 http://onsemi.com 8 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indem nify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and re asonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized u se, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employ er. publication ordering information japan : on semiconductor, japan customer focus center 291 kamimeguro, meguroku, tokyo, japan 1530051 phone : 81357733850 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. nl17szu04/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 8002829855 toll free usa/canada
|
