tlp559 2007-10-01 1 toshiba photocoupler gaa ? a s ired & photo ic tlp559 digital logic ground isolation line receiver microprocessor system interfaces switching power supply feedback control transistor inverter the toshiba tlp559 consists of a gaa ? as high ? output light emitting diode and a high speed detector of one chip photo diode ? transistor. this unit is 8 ? lead dip package. tlp559 has no internal base connection, and a faraday shield integrated on the photodetector chip provides an effective common mode noise transient immunity. so this is suitable for application in noisy environmental condition. ? isolation voltage: 2500vrms (min) ? switching speed: t phl = 0.3 s (typ.) t plh = 0.5 s (typ.) (r l = 1.9k ? ) ? ttl compatible ? ul recognized: ul1577, file no.e67349 pin configuration (top view) shield 1 : n.c. 2 : anode 3 : cathode 4 : n.c. 5 : emitter 6 : collector 7 : n.c. 8 : v cc 1 2 6 8 3 5 4 7 schematic 2 3 v cc 8 i cc i f v f gnd 6 v o i o 5 shield toshiba 11 ? 10c4 weight: 0.54 g (typ.) unit: mm
tlp559 2007-10-01 2 absolute maximum ratings (ta = 25c) characteristic symbol rating unit forward current (note 1 ) i f 25 ma pulse forward current (note 2 ) i fp 50 ma peak transient forward current (note 3 ) i fpt 1 a reverse voltage v r 5 v led diode power dissipation (note 4 ) p d 45 mw output current i o 8 ma peak output current i op 16 ma output voltage v o ?0.5~15 v supply voltage v cc ?0.5~15 v detector output power dissipation (note 5 ) p o 100 mw operating temperature range t opr ?55~100 c storage temperature range t stg ?55~125 c lead solder temperature (10s) (note 6 ) t sol 260 c isolation voltage (ac, 1 min., r.h. 60%) (note 7 ) bv s 2500 vrms note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (note 1) derate 0.8ma above 70c. (note 2) 50% duty cycle,1ms pulse width. derate 1.6ma / c above 70c. (note 3) pulse width 1 s, 300pps. (note 4) derate 0.9mw / c above 70c. (note 5) derate 2mw / c above 70c. (note 6) soldering portion of lead: up to 2mm from body of the devise. (note 7) device considered a two-terminal device: pins 1, 2, 3 and 4 shorted together and pins 5, 6, 7 and 8 shorted together.
tlp559 2007-10-01 3 electrical characteristics (ta = 25c) characteristic symbol test condition min. typ. max. unit forward voltage v f i f = 16ma D 1.65 1.85 v forward voltage temperature coefficient v f / ta i f = 16ma D ?2 D mv / c reverse current i r v r = 5v D D 10 a led capacitance between terminal c t v f = 0, f = 1mhz D 45 D pf i oh (1) i f = 0ma, v cc = v o = 5.5v D 3 500 na i oh (2) i f = 0ma, v cc = v o = 15v D D 5 high level output current i oh i f = 0ma, v cc = 15v v o = 15v, ta = 70c D D 50 a detector high level supply voltage i cch i f = 0ma, v cc = 15v D 0.01 1 a current transfer ratio i o / i f i f = 16ma, v cc = 4.5v v o = 0.4v 20 40 D % low level output voltage v ol i f = 16ma, v cc = 4.5v i o = 2.4ma D D 0.4 v resistance (input ?output) r s r.h. 60%, v s = 500v dc (note 7) 510 10 10 14 D ? coupled capacotance (input ? output) c s v s = 0, f = 1mhz (note 7) D 0.8 D pf switching characteristics (ta = 25c v cc = 5v) characteristic symbol test cir ? cuit test condition min. typ. max. unit propagation delay time (h l) t phl D 0.2 0.8 s propagation delay time (l h) t plh 1 i f = 16ma, r l = 1.9k ? D 0.3 0.8 s common mode transient immunity at logic high output (note 8) cm h i f = 0ma, v cm = 400v p? p r l = 4.1k ? 2000 10000 D v / s common mode transient immunity at logic high output (note 8) cm l 2 i f =16ma, v cm = 400v p? p r l = 4.1k ? ?2000 ?10000 D v / s (note 8) cm l is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic low state (v o < 0.8v). cm h is the maximum rate of rise of the common mode voltage that can be sustain ed with the output voltage in the logic high state (v o < 2.0v). (note 9) maximum electrostatic discharge voltage for any pins: 100v (c = 200pf, r = 0)
tlp559 2007-10-01 4 test circuit 1: switch ing time test circuit test circuit 2: common mode noise immunity test circuit s)( f t 320(v) l cm s)( r t 320(v) h cm =, = i f v o 0 5v 1.5v v ol 1.5v t p hl t p lh v cc = 5v v o pulse in p ut output monito r r l 6 4 3 1 5 7 pw=100 s duty ratio=1 / 10 i f monitor i f 8 2 51 ? v cm 400v v o (i f =0ma) v o (i f =16ma) 0v 5v 2v 0.8v v ol 10% 90% t f t r v cc =5v v o output monito r r l 6 4 3 1 5 7 i f 8 2 v cm pulse g enerato r z o =50
tlp559 2007-10-01 5 forward voltage v f (v) i f ? v f forward current i f (ma) 100 1.0 1 10 0.1 1.2 1.4 1.6 1.8 2.0 0.01 ta = 25c 50 30 5 3 0.5 0.3 0.05 0.03 forward voltage temperature coefficient v f / ta ( m v / ) 0.1 ? 2.2 ? 2.4 ? 2.6 ? 1.4 0.5 0.3 ? 2.0 ? 1.8 ? 1.6 1 3 10 5 v f / ta ? i f forward current i f (ma) 30 ambient temperature ta ( ) high level output current i oh ( a) i oh (1) ? ta 300 1 100 50 3 10 5 30 0.6 1 60 12 0 80 4 0 0 output current i o (ma) forward current i f (ma) l o ? i f 0.1 1 3 10 0.01 0.5 0.3 0.3 0.1 0.03 1 30 100 50 300 10 3 5 0.05 0.5 5 v cc = 5v v o = 0.4v ta = 2 5 c i o / i f ? i f forward current i f (ma) current transfer ratio i o / i f (%) 100 50 30 10 5 3 1 0.3 1 0.5 3 10 30 50 v cc = 5v v o = 0.4v 5 ambient temperature ta ( ) normalized i o / i f i o / i f ? ta 60 40 0 20 ? 20 ? 40 0.2 0 80 0.6 0.4 0.8 1.2 1.0 100 normalized to : i f = 16ma v cc = 4.5v v o = 0.4v ta = 2 5 c ta = ? 25c 25c 100c
tlp559 2007-10-01 6 t phl , t plh ? r l propagation delay time t p lh, t p hl ( s) load resistance r l (k ) 5 3 1 0.5 0.3 0.1 30 1 3 10 50 100 5 t p lh t p hl i f = 16ma v cc = 5v ta = 25c output voltage v o (v) output current i o (ma) i o ? v o 5 4 2 3 0 1 10 8 0 6 4 2 6 7 v cc = 5v ta = 25c 15ma 30ma 25ma 20ma 10ma i f =5ma forward current i f (ma) output voltage v o (v) v o ? i f 20 16 8 12 0 4 5 4 0 3 2 1 24 ta =25 v cc =5v r l v o i f r l =2k 3.9k 10k
tlp559 2007-10-01 7 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software an d systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba?s written permission, reproduc tion is permissible only if reproducti on is without alteration/omission. ? though toshiba works continually to improve product?s quality a nd reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situat ions in which a malfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before creating and producing des igns and using, customers mus t also refer to and comply with (a) the latest versions of all re levant toshiba information, including without limitation, this d ocument, the specifications, the data sheets and applic ation notes for product and the precautions and conditions set forth in the ?tosh iba semiconductor reliability h andbook? and (b) the instructions for the applicati on that product will be used with or for. custome rs are solely responsible for all aspects of t heir own product design or applications, incl uding but not limited to (a) determining th e appropriateness of the use of this product in such design or app lications; (b) evaluating and deter mining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general el ectronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home electroni cs appliances) or for specif ic applications as expre ssly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality a nd/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or se rious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic s ignaling equipment, equipment used to control combustions or explosions, safety devices, elevat ors and escalators, devices related to el ectric power, and equipment used in finance-related fields. do not use product for unintended use unless specifically permitted in thi s document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is presented only as guidance for product use. no resp onsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this documen t, whether express or implied, by estoppel or otherwise. ? absent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? gaas (gallium arsenide) is used in product. gaas is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose gaas in product. ? do not use or otherwise make available product or related soft ware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical , or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. expor t administration regulations. ex port and re-export of product or related software or technology are strictly prohibited exc ept in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations.
|
