View KMM375S1723T_1843128.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev. 1 april. '98 preliminary KMM375S1723T sdram module pin names * these pins are not used in this module. ** these pins should be nc in the system which does not support spd. pin name function a0 ~ a11 address input (multiplexed) ba0 ~ ba1 select bank dq0 ~ dq63 data input/output cb0 ~ cb7 check bit (data-in/data-out) clk0 clock input cke0 clock enable input cs0 , cs2 chip select input ras row address storbe cas colume address strobe we write enable dqm0 ~ 7 dqm v dd power supply (3.3v) v ss ground *v ref power supply for reference rege register enable sda serial data i/o scl serial clock sa0 ~ 2 address in eeprom du don t use nc no connection wp write protection pin configurations (front side/back side) pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 front v ss dq0 dq1 dq2 dq3 v dd dq4 dq5 dq6 dq7 dq8 v ss dq9 dq10 dq11 dq12 dq13 v dd dq14 dq15 cb0 cb1 v ss nc nc v dd we dqm0 pin 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 front dqm1 cs0 du v ss a0 a2 a4 a6 a8 a10/ap ba1 v dd v dd clk0 v ss du cs2 dqm2 dqm3 du v dd nc nc cb2 cb3 v ss dq16 dq17 pin 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 front dq18 dq19 v dd dq20 nc *v ref *cke1 v ss dq21 dq22 dq23 v ss dq24 dq25 dq26 dq27 v dd dq28 dq29 dq30 dq31 v ss *clk2 nc nc/wp **sda **scl v dd pin 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 back v ss dq32 dq33 dq34 dq35 v dd dq36 dq37 dq38 dq39 dq40 v ss dq41 dq42 dq43 dq44 dq45 v dd dq46 dq47 cb4 cb5 v ss nc nc v dd cas dqm4 pin 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 back dqm5 * cs1 ras v ss a1 a3 a5 a7 a9 ba0 a11 v dd *clk1 *a12 v ss cke0 * cs3 dqm6 dqm7 *a13 v dd nc nc cb6 cb7 v ss dq48 dq49 pin 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 back dq50 dq51 v dd dq52 nc *v ref rege v ss dq53 dq54 dq55 v ss dq56 dq57 dq58 dq59 v dd dq60 dq61 dq62 dq63 v ss *clk3 nc **sa0 **sa1 **sa2 v dd the samsung KMM375S1723T is a 16m bit x 72 synchro- nous dynamic ram high density memory module. the sam- sung KMM375S1723T consists of nine cmos 16mx8 bit synchronous drams in tsop-ii 400mil packages, two 18-bits drive ics for input control signal, one pll in 24-pin tssop package for clock and one 2k eeprom in 8-pin tssop pack- age for serial presence detect on a 168-pin glass-epoxy sub- strate. two 0.1uf decoupling capacitors are mounted on the printed circuit board in parallel for each sdram. the KMM375S1723T is a dual in-line memory module and is intented for mounting into 168-pin edge connector sockets. synchronous design allows precise cycle control with the use of system clock. i/o transactions are possible on every clock cycle. range of operating frequencies, programmable laten- cies allows the same device to be useful for a variety of high bandwidth, high performance memory system applications. general description KMM375S1723T sdram dimm 16mx72 sdram dimm with pll & register based on 16mx8, 4banks 4k ref., 3.3v synchronous drams with spd ? performance range part no. max freq. (speed) KMM375S1723T-g8 KMM375S1723T-gh KMM375S1723T-gl KMM375S1723T-g0 ? burst mode operation ? auto & self refresh capability (4096 cycles/64ms) ? lvttl compatible inputs and outputs ? single 3.3v 0.3v power supply ? mrs cycle with address key programs latency (access from column address) burst length (1, 2, 4, 8 & full page) data scramble (sequential & interleave) ? all inputs are sampled at the positive going edge of the system clock ? serial presence detect with eeprom ? pcb : height(1,450mil) , double sided component feature samsung electronics co., ltd. reserves the right to change products and specifications without notice. 125mhz (8ns @ cl=3) 100mhz (10ns @ cl=2) 100mhz (10ns @ cl=3) 100mhz (10ns @ cl=3)
rev. 1 april. '98 preliminary KMM375S1723T sdram module pin configuration description pin name input function clk system clock active on the positive going edge to sample all inputs. cs chip select disables or enables device operation by masking or enabling all inputs except clk, cke and dqm cke clock enable masks system clock to freeze operation from the next clock cycle. cke should be enabled at least one cycle prior to new command. disable input buffers for power down in standby. cke should be enabled 1clk+tss prior to valid command. a0 ~ a11 address row/column addresses are multiplexed on the same pins. row address : ra0 ~ ra11, column address : ca0 ~ ca9 ba0 ~ ba1 bank select address selects bank to be activated during row address latch time. selects bank for read/write during column address latch time. ras row address strobe latches row addresses on the positive going edge of the clk with ras low. enables row access & precharge. cas column address strobe latches column addresses on the positive going edge of the clk with cas low. enables column access. we write enable enables write operation and row precharge. latches data in starting from cas , we active. dqm0 ~ 7 data input/output mask makes data output hi-z, t shz after the clock and masks the output. blocks data input when dqm active. (byte masking) rege register enable the device operates in the transparent mode when rege is low. the a data is latched if clk is held at a high or low logic level . if rege is low , the a-bus data is stored in the latch/flip-flop on the low-to-high transition of clk. rege is tied to vcc through 10k ohm resistor on pcb. so if rege of module is float- ing , this module will be operated as registered mode. dq0 ~63 data input/output data inputs/outputs are multiplexed on the same pins. cb0 ~ 7 check bit check bits for ecc. v dd /v ss power supply/ground power and ground for the input buffers and the core logic.
rev. 1 april. '98 preliminary KMM375S1723T sdram module a0~a9 ras , cas , we dqm0,1,4,5 cs0 rege pclk2 b 0 a0~b 0 a9 bras , bcas , bwe bdqm0,1,4,5 bcs0 sn74alvc162835 a10,a11,ba0~1 cs2 cke0 dqm2,3,6,7 b 0 a10,b 0 a11,bba0~1 bcs2 bcke0 bdqm2,3,6,7 vcc 10k w oe le sn74alvc162835 oe le 12 pf functional block diagram functional block diagram clk cs cke add,ctl dqm dq0~7 d0 pclk0 bcs0 bcke0 b 0 a0~b 0 a11,bba0~1, bras , bcas , bwe bdqm0 dq0~7 clk cs cke add,ctl dqm dq0~7 d1 dq8~15 clk cs cke add,ctl dqm dq0~7 d2 pclk1 bdqm1 cb0~7 clk cs cke add,ctl dqm dq0~7 d3 clk cs cke add,ctl dqm dq0~7 d5 clk cs cke add,ctl dqm dq0~7 d4 clk cs cke add,ctl dqm dq0~7 d6 clk cs cke add,ctl dqm dq0~7 d8 bdqm7 dq56~63 clk cs cke add,ctl dqm dq0~7 d7 10 w 10 w bcs2 bdqm2 dq16~23 pclk3 bdqm3 dq24~31 bdqm4 dq32~39 bdqm5 dq40~47 bdqm6 dq48~55 serial pd sda scl a1 a2 a0 sa1 sa2 sa0 cdc2509a 2 g a g n d 1 g a v c l 1y0 1y1 1y2 1y3 1y4 2y0 2y1 2y2 2y3 clk fibin v ss 10 w vcc clk0 fbout pclk0 pclk1 pclk2 pclk3 wp 47k w 24 pf 10 w 10 w 10 w 10 w 10 w 10 w 10 w
rev. 1 april. '98 preliminary KMM375S1723T sdram module *1. register input 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 clk ras cas we ras cas we cas latency(refer to *1) tsac trdl read row active command precharge command row active write command precharge command 1clk td tr td tr td, tr = delay of register (sn74alvc162835 of ti) notes : 1. in case of module timing, command cycles delayed 1clk with respect to external input timing at the address and input signal because of the buffering in register (sn74alvc162835). therefore, input/output signals of read/write function s hould be issued 1clk earlier as compared to unbuffered dimms. 2. d in is to be issued 1clock after write command in external timing because d in is issued directly to module. : don t care standard timing diagram with pll & register (cl=2, bl=4) *2. register output *3. sdram reg control signal( ras , cas , we ) *1 *2 *3 d out =2clk+1clk trac(refer to *1) trac(refer to *2) cas latency(refer to *2) dq qa0 qa1 qa2 qa3 db0 db1 db2 db3 =2clk
rev. 1 april. '98 preliminary KMM375S1723T sdram module absolute maximum ratings parameter symbol value unit voltage on any pin relative to vss v in , v out -1.0 ~ 4.6 v voltage on v dd supply relative to vss v dd , v ddq -1.0 ~ 4.6 v storage temperature t stg -55 ~ +150 c power dissipation p d 9 w short circuit current i os 50 ma permanent device damage may occur if "absolute maximum ratings" are exceeded. functional operation should be restricted to recommended operating condition. exposure to higher than recommended voltage for extended periods of time could affect device reliability. note : dc operating conditions and characteristics recommended operating conditions (voltage referenced to v ss = 0v, t a = 0 to 70 c) parameter symbol min typ max unit note supply voltage v dd 3.0 3.3 3.6 v input high voltage v ih 2.0 3.0 v ddq +0.3 v 1 input low voltage v il -0.3 0 0.8 v 2 output high voltage v oh 2.4 - - v i oh = -2ma output low voltage v ol - - 0.4 v i ol = 2ma input leakage current (inputs) i il -9 - 9 ua 3 input leakage current (i/o pins) i il -1.5 - 1.5 ua 3,4 capacitance (v dd = 3.3v, t a = 23 c, f = 1mhz, v ref =1.4v 200 mv) parameter symbol min max unit input capacitance (a 0 ~ a 11 ) input capacitance ( ras , cas , we ) input capacitance (cke0 ~ cke1) input capacitance (clk0) input capacitance ( cs0 , cs2 ) input capacitance (dqm0 ~ dqm7) input capacitance (ba0 ~ ba1) data input/output capacitance (dq0 ~ dq63) c in1 c in2 c in3 c in4 c in5 c in6 c in7 c out - - - - - - - - 16 16 16 14 16 16 16 23 pf pf pf pf pf pf pf pf 1. v ih (max) = 5.6v ac. the overshoot voltage duration is 3ns. 2. v il (min) = -2.0v ac. the undershoot voltage duration is 3ns. 3. any input 0v v in v ddq. input leakage currents include hi-z output leakage for all bi-directional buffers with tri-state outputs. 4. dout is disabled, 0v v out v ddq. notes :
rev. 1 april. '98 preliminary KMM375S1723T sdram module dc characteristics (recommended operating condition unless otherwise noted, t a = 0 to 70 c) parameter symbol test condition cas latency version unit note -8 -h -l -0 operating current (one bank active) i cc1 burst length = 1 t rc 3 t rc (min) i ol = 0 ma 1,080 990 990 945 ma 1 precharge standby current in power-down mode i cc2 p cke v il (max), t cc = 15ns 9 ma i cc2 ps cke & clk v il (max), t cc = 9 precharge standby current in non power-down mode i cc2 n cke 3 v ih (min), cs 3 v ih (min), t cc = 15ns input signals are changed one time during 30ns 135 ma i cc2 ns cke 3 v ih (min), clk v il (max), t cc = input signals are stable 63 active standby current in power-down mode i cc3 p cke v il (max), t cc = 15ns 45 ma i cc3 ps cke & clk v il (max), t cc = 45 active standby current in non power-down mode (one bank active) i cc3 n cke 3 v ih (min), cs 3 v ih (min), t cc = 15ns input signals are changed one time during 30ns 270 ma i cc3 ns cke 3 v ih (min), clk v il (max), t cc = input signals are stable 180 ma operating current (burst mode) i cc4 i ol = 0 ma page burst t ccd = 2clks 3 1,350 1,125 1,125 1,125 ma 1 2 1,035 1,125 1,035 1,035 refresh current i cc5 t rc 3 t rc (min) 1,800 1,485 ma 2 self refresh current i cc6 cke 0.2v 99 ma 3 1. measured with outputs open. 2. refresh period is 64ms. 3. measured with 1 pll & 2 drive ics. notes :
rev. 1 april. '98 preliminary KMM375S1723T sdram module 3.3v 1200 w 870 w output 50pf v oh (dc) = 2.4v, i oh = -2ma v ol (dc) = 0.4v, i ol = 2ma vtt = 1.4v 50 w output 50pf z0 = 50 w (fig. 2) ac output load circuit (fig. 1) dc output load circuit ac operating test conditions (v dd = 3.3v 0.3v , t a = 0 to 70 c) parameter value unit ac input levels (vih/vil) 2.4/0.4 v input timing measurement reference level 1.4 v input rise and fall time tr/tf = 1/1 ns output timing measurement reference level 1.4 v output load condition see fig. 2 operating ac parameter (ac operating conditions unless otherwise noted) parameter symbol version unit note-0 -8 -h -l -0 row active to row active delay t rrd (min) 16 20 20 20 ns 1 ras to cas delay t rcd (min) 20 20 20 24 ns 1 row precharge time t rp (min) 20 20 20 24 ns 1 row active time t ras (min) 48 50 50 50 ns 1 t ras (max) 100 us row cycle time t rc (min) 68 70 70 80 ns 1 last data in to row precharge t rdl (min) 8 10 10 12 ns 2 last data in to new col. address delay t cdl (min) 1 clk 2 last data in to burst stop t bdl (min) 1 clk 2 col. address to col. address delay t ccd (min) 1 clk 3 number of valid output data cas latency=3 2 ea 4 cas latency=2 1 1. the minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and then rounding off to the next higher integer. 2. minimum delay is required to complete write. 3. all parts allow every cycle column address change. 4. in case of row precharge interrupt, auto precharge and read burst stop. notes :
rev. 1 april. '98 preliminary KMM375S1723T sdram module ac characteristics (ac operating conditions unless otherwise noted) parameter symbol -8 -h -l -0 unit note min max min max min max min max clk cycle time cas latency=3 t cc 8 1000 10 1000 10 1000 10 1000 ns 1 cas latency=2 12 10 12 13 clk to valid output delay cas latency=3 t sac 6 6 6 7 ns 1,2 cas latency=2 6 6 7 7 output data hold time cas latency=3 t oh 3 3 3 3 ns 1,2 cas latency=2 3 3 3 3 clk high pulse width t ch 3 3 3 3.5 ns 3 clk low pulse width t cl 3 3 3 3.5 ns 3 input setup time t ss 2 2 2 2.5 ns 3 input hold time t sh 1 1 1 1.5 ns 3 clk to output in low-z t slz 1 1 1 1 ns 2 clk to output in hi-z cas latency=3 t shz 6 6 6 7 ns 1 cas latency=2 6 6 7 7 1. parameters depend on programmed cas latency. 2. if clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter. 3. assumed input rise and fall time (tr & tf) = 1ns. if tr & tf is longer than 1ns, transient time compensation should be considered, i.e., [(tr + tf)/2-1]ns should be added to the parameter. notes :
rev. 1 april. '98 preliminary KMM375S1723T sdram module frequency vs. ac parameter relationship table KMM375S1723T-8 frequency cas latency t rc t ras t rp t rrd t rcd t ccd t cdl t rdl 68ns 48ns 20ns 16ns 20ns 8ns 8ns 8ns 125mhz (8.0ns) 3 9 6 3 2 3 1 1 1 100mhz (10.0ns) 3 7 5 2 2 2 1 1 1 83mhz (12.0ns) 2 6 4 2 2 2 1 1 1 75mhz (13.0ns) 2 6 4 2 2 2 1 1 1 66mhz (15.0ns) 2 5 4 2 2 2 1 1 1 (unit : number of clock) KMM375S1723T-l frequency cas latency t rc t ras t rp t rrd t rcd t ccd t cdl t rdl 70ns 50ns 20ns 20ns 20ns 10ns 10ns 10ns 100mhz (10.0ns) 3 7 5 2 2 2 1 1 1 83mhz (12.0ns) 2 6 5 2 2 2 1 1 1 75mhz (13.0ns) 2 6 4 2 2 2 1 1 1 66mhz (15.0ns) 2 5 4 2 2 2 1 1 1 60mhz (16.7ns) 2 5 3 2 2 2 1 1 1 (unit : number of clock) KMM375S1723T-h frequency cas latency t rc t ras t rp t rrd t rcd t ccd t cdl t rdl 70ns 50ns 20ns 20ns 20ns 10ns 10ns 10ns 100mhz (10.0ns) 2 7 5 2 2 2 1 1 1 83mhz (12.0ns) 2 6 5 2 2 2 1 1 1 75mhz (13.0ns) 2 6 4 2 2 2 1 1 1 66mhz (15.0ns) 2 5 4 2 2 2 1 1 1 60mhz (16.7ns) 2 5 3 2 2 2 1 1 1 (unit : number of clock) KMM375S1723T-0 frequency cas latency t rc t ras t rp t rrd t rcd t ccd t cdl t rdl 80ns 50ns 24ns 20ns 24ns 10ns 10ns 12ns 100mhz (10.0ns) 3 8 5 3 2 3 1 1 2 83mhz (12.0ns) 3 7 5 2 2 2 1 1 1 75mhz (13.0ns) 2 7 4 2 2 2 1 1 1 66mhz (15.0ns) 2 6 4 2 2 2 1 1 1 60mhz (16.7ns) 2 5 3 2 2 2 1 1 1 (unit : number of clock)
rev. 1 april. '98 preliminary KMM375S1723T sdram module notes : simplified truth table command cken-1 cken cs ras cas we dqm ba 0,1 a 10 /ap a 11, a 9 ~ a 0 note register mode register set h x l l l l x op code 1,2 refresh auto refresh h h l l l h x x 3 self refresh entry l 3 exit l h l h h h x x 3 h x x x 3 bank active & row addr. h x l l h h x v row address read & column address auto precharge disable h x l h l h x v l column address (a 0 ~ a 9 ) 4 auto precharge enable h 4,5 write & column address auto precharge disable h x l h l l x v l column address (a 0 ~ a 9 ) 4 auto precharge enable h 4,5 burst stop h x l h h l x x 6 precharge bank selection h x l l h l x v l x all banks x h clock suspend or active power down entry h l h x x x x x l v v v exit l h x x x x x precharge power down mode entry h l h x x x x x l h h h exit l h h x x x x l v v v dqm h v x 7 no operation command h x h x x x x x l h h h 1. op code : operand code a 0 ~ a 11 & ba 0 ~ ba 1 : program keys. (@ mrs) 2. mrs can be issued only at all banks precharge state. a new command can be issued after 2 clock cycles of mrs. 3. auto refresh functions are as same as cbr refresh of dram. the automatical precharge without row precharge command is meant by "auto". auto/self refresh can be issued only at all banks precharge state. 4. ba 0 ~ ba 1 : bank select addresses. if both ba 0 and ba 1 are "low" at read, write, row active and precharge, bank a is selected. if both ba 0 is "low" and ba 1 is "high" at read, write, row active and precharge, bank b is selected. if both ba 0 is "high" and ba 1 is "low" at read, write, row active and precharge, bank c is selected. if both ba 0 and ba 1 are "high" at read, write, row active and precharge, bank d is selected. if a 10 /ap is "high" at row precharge, ba 0 and ba 1 is ignored and all banks are selected. 5. during burst read or write with auto precharge, new read/write command can not be issued. another bank read/write command can be issued after the end of burst. new row active of the associated bank can be issued at t rp after the end of burst. 6. burst stop command is valid at every burst length. 7. dqm sampled at positive going edge of a clk and masks the data-in at the very clk (write dqm latency is 0), but makes hi-z state the data-out of 2 clk cycles after. (read dqm latency is 2) (v=valid, x=don t care, h=logic high, l=logic low)
rev. 1 april. '98 preliminary KMM375S1723T sdram module package dimensions 5.250 5.014 units : inches (millimeters) 0.050 0.039 .002 0.010max (0.250 max) 0.150max 0.050 0.0039 (1.270 0.10) r 0.079 (r 2.000) 0.250 (6.350) 1.450 (36.830) 2.150 (54.61) 0 . 1 1 8 ( 3 . 0 0 0 ) 0.350 0 . 1 0 0 m i n ( 2 . 5 4 0 m i n ) 0 . 7 0 0 ( 1 7 . 7 8 0 ) (1.000 . 050) (1.270 ) 0 . 1 0 0 m i n ( 2 . 5 4 0 m i n ) detail c .118dia .004 (3.000dia .100) (8.890) a c 0.250 (6.350) .450 (11.430) 4.550 (115.57) 0.157 0.004 (4.000 0.100 ) 0.054 (1.372) (127.350) (133.350) 1 . 6 5 0 ( 4 1 . 9 4 9 ) 0.118 (3.000) 0.250 (6.350 ) detail a 0.123 .005 (3.125 .125) 0.250 (6.350 ) detail b 0.123 .005 (3.125 .125) 0.079 .004 (2.000 .100) 0.079 .004 (2.000 .100) 0 . 1 6 5 m i n ( 4 . 1 9 m i n ) (3.81max) tolerances : .005(.13) unless otherwise specified the used device is 8mx8 sdram, tsop sdram part no. : km48s8030bt b reg pll reg

▲Up To Search▲

Price & Availability of KMM375S1723T

	To Download KMM375S1723T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .