![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
product specification 0/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 specification for approval 14.1 wxga+ tft lcd title model general buyer *when you obtain standard approval, please use the above model name without suffix lp141wp2 *model tla1 suffix lg display co., ltd. supplier signature please return 1 copy for your confirmation with your signature and comments. / / / approved by ) ) ( ( final specification preliminary specification k. j. kwon / s.manager product engineering dept. lg display co., ltd approved by signature reviewed by prepared by g. j. han / manager k. y. kwon / engineer www..net www..net
product specification 1/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 contents 23 precautions 9 11 6 interface connections 3-2 color input data refernece 3-5 22 designation of lot mark 8-1 22 packing form 8-2 packing 8 21 emc 7-2 1 contents 2 record of revisions 3 general description 1 4 absolute maximum ratings 2 electrical specifications 3 5 electrical charactreistics 3-1 8 signal timing specifications 3-3 10 signal timing waveforms 3-4 12 power sequence 3-6 13 optical sfecifications 4 16 mechanical characteristics 5 20 reliablity 6 international standards 7 21 safety 7-1 page item no www..net www..net product specification 2/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 record of revisions 0.0 edid ver first draft (preliminary specification) - 22. apr. 2008 0.0 description page revision date revision no www..net www..net product specification 3/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 1. general description general features yes rohs comply hard coating(3h) anti glare treatment of the front polarizer surface treatment 6-bit, 262,144 colors color depth 1440 horiz. by 900 vert. pixels rgb strip arrangement pixel format 300 cd/m 2 (typ., @i led =19ma) , 5 points average luminance, white total 5.45watt @ lcm circuit 1.55w(typ.), b/l 3.3 w (typ.), led driver 0.6w(typ.) power consumption 375g(max.) weight transmissive mode, normally white display operating mode 0.2106 mm 0.2106 mm pixel pitch 320.0 (h) 207.0 (v) 5.5(d, max.) mm outline dimension 14.1 inches diagonal active screen size the lp141wp2 is a color active matrix liquid crysta l display with an integral led backlight system. th e matrix employs a-si thin film transistor as the act ive element. it is a transmissive type display oper ating in the normally white mode. this tft-lcd has 14.1 inch es diagonally measured active display area with wxga+ resolution(1440 horizontal by 900 vertical pi xel array). each pixel is divided into red, green a nd blue sub-pixels or dots which are arranged in verti cal stripes. gray scale or the brightness of the su b-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more th an 262,144 colors. the lp141wp2 has been designed to apply the interfa ce method that enables low power, high speed, low emi. the lp141wp2 is intended to support applications wh ere thin thickness, low power are critical factors and graphic displays are important. in combination with the vertical arrangement of the sub-pixels, the lp141wp2 characteristics provide an excellent flat display for office automation products such as note book pc. control & data power edid signal & power tft-lcd panel (1440 x 900) 1 900 1 1440 cn 1 user connector 50 pin power block edid block gate in panel source driver circuit led backlight ass y 9leds x 6 strings lvds & timing control block pwm & vbl & smbus www..net www..net product specification 4/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 2. absolute maximum ratings the following are maximum values which, if exceeded , may cause faulty operation or damage to the unit. table 1. absolute maximum ratings storage operation 10 20 30 40 50 60 70 80 0 -20 dry bulb temperature [ ] 10 % 20 % 40 % 60 % 90% 80% 0 10 20 30 40 50 60 wet bulb temperature [ ] humidity[(%)rh] units 1 %rh 90 10 h op operating ambient humidity 1 %rh 90 10 h st storage humidity 1 c 60 -20 h st storage temperature 1 c 50 0 t op operating temperature at 25 5 c vdc 4.0 -0.3 vcc power input voltage max min parameter notes values symbol note : 1. temperature and relative humidity range a re shown in the figure below. wet bulb temperature should be 39 c max, and no condensation of water. www..net www..net product specification 5/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 3. electrical specifications 3-1. electrical characteristics the lp141wp2 requires two power inputs. one is emp loyed to power the lcd electronics and to drive the tft array and liquid crystal. the second input whic h powers the led bl. table 2. electrical characteristics 5 watt 3.5 3.3 - p bl power consumption led backlight : 3 v 30.6 28.8 - v led operating voltage 4 ma - 19 - i led operating current per string 6 hrs - - 10,000 life time 2 ohm 110 100 90 zm differential impedance 1 watt 1.78 1.55 - pc power consumption v dc 3.6 3.3 3.0 vcc power supply input voltage 1 ma 540 470 400 i cc power supply input current module : parameter symbol max typ min notes unit values note) 1. the specified current and power consumption are under the vcc = 3.3v , 25 , fv = 60hz condition whereas mosaic pattern is displayed and fv is the f rame frequency. 2. this impedance value is needed to proper display and measured form lvds tx to the mating connector. 3. the variance of the voltage is 10%. 4. the typical operating current is for the typica l surface luminance (l wh ) in optical characteristics. i led is the current of each leds string, led backlight h as 6 strings on it. 5. the led power consumption shown above does not i nclude power of external led driver circuit for typical current condition. 6. the life time is determined as the time at which brightness of led is 50% compare to that of initia l value at the typical led current. www..net www..net product specification 6/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 3-2. interface connections table 3. module connector pin configuration (cn1) this lcd employs two interface connections, a 50 pi n connector is used for the module electronics inte rface and the other connector is used for the internal ba cklight system. the electronics interface connector is a model fi-v hp50s manufactured by jae. test loop (only to pin 1) test loop 30 negative lvds differential data input odd_rin0- 7 ground vss1 9 positive lvds differential data input odd_rin0+ 8 ground vss 6 edid data data eedid 5 edid clock clk eedid 4 ground vss 3 edid 3.3v power veedid 2 test loop (only to pin 30) test loop 1 positive lvds differential clock input odd_clkin+ 17 negative lvds differential clock input even_clkin- 28 positive lvds differential clock input even_clkin+ 29 positive lvds differential data input odd_rin1+ 11 ground vss2 12 negative lvds differential data input odd_rin2- 13 positive lvds differential data input odd_rin2+ 14 ground vss3 15 negative lvds differential clock input odd_clkin- 16 ground vss4 18 negative lvds differential data input even_rin0- 19 positive lvds differential data input even_rin0+ 20 ground vss5 21 negative lvds differential data input even_rin1- 22 positive lvds differential data input even_rin1+ 23 ground vss6 24 negative lvds differential data input even_rin2- 25 positive lvds differential data input even_rin2+ 26 ground vss7 27 notes description symbol pin odd_rin1- 1, interface chips 1.1 lcd : sw, st2_bs (lcd controller) including lvds receiver 1.2 system : * pin to pin compatible with lvds 2.connector 2.1 lcd :jae fi-vhp50 or equivalent (1.0 mm thickness, lock-in type, pin 1 starts from left on the front) 2.2 mating:jae fi-vhp50 series or equivalent (micro-coax type) 2.3 connector pin arrangement lcd rear view negative lvds differential data input 10 50 1 [lcd module rear view] www..net www..net product specification 7/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 the led backlight connector is a model tf12-9s-0.5h , manufactured by hirose. table 4. backlight connector pin configuration (cn 2) led cathode (negative) vdc4 7 led cathode (negative) vdc1 4 led cathode (negative) vdc2 5 no connection nc 3 led cathode (negative) vdc3 6 led anode(positive) vdc(1,2,3,4,5,6) 2 led cathode (negative) vdc5 8 led cathode (negative) vdc6 9 led anode(positive) vdc(1,2,3,4,5,6) 1 notes description symbol pin 9 1 smbus clk smb_clk 19 ground vss 6 no connection +5v_alw 5 panel self test test(bist_en) 4 logic power 3.3v vdd 3 logic power 3.3v vdd 2 connector test (only to pin 20) conntst 1 7v ~ 20v led power vbl+ 17 smbus data smb_data 18 connector test(only to pin 1) conntst 20 7v ~ 20v led power vbl+ 16 7v ~ 20v led power vbl+ 15 7v ~ 20v led power vbl+ 14 no connect nc 13 led power return vbl- 12 led power return vbl- 11 led power return vbl- 10 led power return vbl- 9 pwm brightness control pwm_bl 8 ground vss 7 www..net www..net product specification 8/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 notes unit max min symbol description 85mhz > fclk 65mhz ps + 400 - 400 t skew lvds clock to data skew margin - - - 65mhz > fclk 25mhz % 3 - f dev maximum deviation of input clock frequency during ssc khz 200 - f mod maximum modulation frequency of input clock during ssc - 1/7 - 600 t clk + 1/7 t skew_eo lvds clock to clock skew margin (even to odd) ps + 600 t skew - v 2.1 0.3 v in lvds input voltage range - v 1.8 0.6 v cm lvds common mode voltage - mv 600 100 |v id | lvds differential voltage notes unit max min symb ol description 3-3-1. dc specification 3-3-2. ac specification 3-3. lvds signal timing specifications www..net www..net product specification 9/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 < clock skew margin between channel > < lvds data format > 3-3-3. data format - lvds 2 port < spread spectrum > time f center f max f min f mod 1 f center * f dev freq. www..net www..net product specification 10/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 3-3-4. signal timing specifications table 5. timing table this is the signal timing required at the input of the user connector. all of the interface signal ti ming should be satisfied with the following specifications and spe cifications of lvds tx/rx for its proper operation. 3-4. signal timing waveforms condition : v cc =2.5v low: 0.3vcc high: 0.7vcc hsync date enable vsync date enable t wh t hp t hfp t hbp t vp t wv t vbp t vfp t wha t wva 939 926 920 tw va active 928 912 896 tw ha active tclk 160 152 144 t hbp horizontal back porch 28 24 20 t hfp horizontal front porch thp 23 17 12 t vbp vertical back porch 6 3 2 t vfp vertical front porch thp 10 6 3 t vp period 900 900 900 t wv width-active 720 720 720 t wh width-active tclk 16 16 16 t hp period hsync vsync data enable mhz - 50.8 - f clk frequency dclk note note note note unit unit unit unit max. max. max. max. typ. typ. typ. typ. min. min. min. min. symbol symbol symbol symbol item item item item www..net www..net product specification 11/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 3-5. color input data reference the brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter t he color. the table below provides a reference for color versus data input. table 6. color data reference 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (00) green 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 green (01) ... 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (62) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (00) red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 red (01) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 red (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 red (63) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 blue (01) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (62) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 blue (63) blue (00) white yellow magenta cyan blue green red black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 basic color 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 blue msb lsb green msb lsb red msb lsb b 5 b 4 b 3 b 2 b 1 b 0 g 5 g 4 g 3 g 2 g 1 g 0 r 5 r 4 r 3 r 2 r 1 r 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue color input color data www..net www..net product specification 12/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 3-6. power sequence note) 1. valid data is data to meet 3-3. lvds signal tim ing specifications 2. please avoid floating state of interface signal at invalid period. 3. when the interface signal is invalid, be sure to pull down the power supply for lcd vcc to 0v. 4. lamp power must be turn on after power supply fo r lcd and interface signal are valid. (ms) - - 400 t 7 (ms) 10 - 0 t 6 (ms) 50 - 0 t 5 (ms) - - 200 t 4 (ms) - - 200 t 3 (ms) 50 - 0 t 2 (ms) 10 - 0 t 1 max. typ. min. units value parameter table 7. power sequence table t 6 interface signal, v i (lvds signal of transmitter) led power power supply for lcd vcc 90% 10% 10% 0v 90% t 1 t 2 t 5 off off led on t 7 t 3 t 4 valid data 0v www..net www..net product specification 13/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 4. optical specification fig. 1 optical characteristic measurement equipment and method table 8. optical characteristics ta=25 c, vcc=3.3v, f v =60hz, f clk = 102mhz, i led = 19ma lcd module optical stage(x,y) equipment 500mm 50mm optical characteristics are determined after the un it has been on and stable for approximately 20 min utes in a dark environment at 25 c . the values specified are at an approximate distan ce 50cm from the lcd surface at a viewing angle of f and q equal to 0 . fig. 1 presents additional information concerning t he measurement equipment and method. 5 viewing angle color coordinates 4 ms 25 16 tr r + tr d response time 0.163 0.133 0.103 by +/- 0.030 0.343 0.313 0.283 wx white y axis, down ( f =270 ) y axis, up ( f =90 ) x axis, left ( f =180 ) x axis, right( f =0 ) degree - 45 40 q r degree - 45 40 q l degree - 15 10 q u degree - 35 30 q d blue +/- 0.030 0.359 0.329 0.299 wy 6 - gray scale green red 0.359 0.329 0.299 gx 0.580 0.550 0.520 gy 0.607 0.577 0.547 rx 0.379 0.349 0.319 ry 3 1.6 1.4 d white luminance variation(13points) 0.192 0.162 0.132 bx max typ min 1 - - 300 cr contrast ratio 2 cd/m 2 - 300 250 l wh surface luminance, white parameter symbol notes units values www..net www..net product specification 14/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 notes) 1. contrast ratio(cr) is defined mathematically as surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is the 5point (1~5)average acr oss the lcd surface 50cm from the surface with all pixels displaying white. for more inform ation see fig 2. when i led = 19ma, l wh =300cd/m 2 (typ.) 3. luminance variation is measured for 13 point for more information see fig 2. white = maximum(ln1,ln2, .. ln13) minimum(ln1,ln2, .. ln13) 4. response time is the time required for the displ ay to transition from white to black (rise time, tr r ) and from black to white(decay time, tr d ). for additional information see fig 3. 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determine d for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to t he lcd surface. for more information see fig 4. 6. gray scale specification * f v =60hz 100 l63 73.0 l55 10.7 l23 19.9 l31 33.0 l39 50.8 l47 4.5 l15 1.47 l7 0.33 l0 luminance [%] (typ) gray level www..net www..net product specification 15/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 fig. 4 viewing angle product specification 16/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 5. mechanical characteristics the contents provide general mechanical characteris tics for the model lp141wp2. in addition the figures in the next page are detai led mechanical drawing of the lcd. 189.54 mm vertical hard coating(3h) anti glare treatment of the front p olarizer surface treatment 375g (max.) weight 193.8mm vertical 206.5 0.50mm vertical 5.5mm(max.) depth 303.264mm horizontal active display area 308.4mm horizontal bezel area 319.5 0.50mm horizontal outline dimension www..net www..net product specification 17/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 product specification 18/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 product specification 19/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 [ detail description of side mounting screw ] notes : 1. screw plated through the method of non-e lectrolytic nickel plating is preferred to reduce possibility that results in vertical and/ or horizontal line defect due to the conductive particles from screw surface. * mounting screw length (a) = 2.0(min) / 2.5(max) * mounting screw hole depth (b) = 2.5(min) * torque : 2.5 kgf.cm(max) (measurement gauge : torque meter) * ppid label revision : it is subject to change with dell event. please ref er to the below table for detail. a09 a29 a19 a09 9th revision a02 a01 a00 xb(mp) x22 x21 x20 st(cs) x12 x11 x10 pt(es) sst(ws) classification x02 x01 x00 2nd revision 1st revision no change * ppid label revision 37 mm 78 mm [ detail information of ppid label and revision cod e ] www..net www..net product specification 20/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 lpl proposal for system cover design.(appendix) define define 1. rear side of lcm is sensitive against external stre ss,and previous check about interference is highly needed. 2.in case there is something from system cover come s into the boundary above,mechanical interference may cause the fos def ects. (eg:ripple,white spot..) check if antenna cable is sufficiently apart from t -con of lcd module. 2 1 gap check for securing the enough gap between lcm and system cover. no good good 1.if system antenna is overlapped with t-con,it mi ght be cause the noise. www..net www..net product specification 21/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 lpl proposal for system cover design. 1.cof area needs to be handled with care. define 1 .at least 2.0mm of gap needs to be secured to preve nt the shock related defects. define 2.l type of hinge is recommended than i type unde r shock test. 2.good wire path design to system side. ok wire path is located between cofs. bad wire path overlapped with cof area. 4 3 gap check for securing the enough gap between lcm and system hinge. checking the path of the system wire. #1 #2 #3 #4 #5 #6 ok bad good www..net www..net product specification 22/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 lpl proposal for system cover design. 1.cnt area is specially sensitive against external stress,and additional gap by cutting on system cover will be helpful on r emoving the ripple. 2.using a thinner cnt will be better. (eg: fpc type ) define 1.condition without bracket is good for mechanical noise,and can minimize the light leakage from deformation of bracket. define 2.the results shows that there is no difference bet ween the condition with or without bracket. securing additional gap on cnt area.. 6 5 using a bracket on the top of lcm is not recommend ed. with bracket without bracket bracket user connector cable pathway. system cover inner side. user connector area. fpc:flexible printed circuit. cut a a-1 a~a-1 www..net www..net product specification 23/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 6. reliability environment test condition { result evaluation criteria } there should be no change which might affect the pr actical display function when the display quality test is conducted under normal operating condition. 0 ~ 10,000 feet (3,048m) 24hr 0 ~ 40,000 feet (12,192m) 24hr altitude operatin g storage / shipment 7 - no functional or cosmetic defects following a shoc k to all 6 sides delivering at least 180 g in a half sine pulse no longer than 2 ms to the display module - no functional defects following a shock delivering at least 200 g in a half sine pulse no longer than 2 ms to each of 6 sides. each of the 6 sides will be shock tested with one each display, for a total of 6 displays shock test (non-operating) 6 sine wave, 5 ~ 150hz, 1.5g, 0.37oct/min 3 axis, 30min/axis vibration test (non-operating) 5 ta= 0 c, 240h low temperature operation test 4 ta= 50 c, 50%rh, 240h high temperature operation test 3 ta= -20 c, 240h low temperature storage test 2 ta= 60 c, 240h high temperature storage test 1 conditions test item no. www..net www..net product specification 24/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 7. international standards 7-1. safety 7-2. emc a) ansi c63.4 methods of measurement of radio-nois e emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992 b) c.i.s.p.r limits and methods of measurement of radio interface characteristics of information technology equipment. international special committ ee on radio interference. c) en 55022 limits and methods of measurement of r adio interface characteristics of information technology equipment. european committee for electr otechnical standardization.(cenelec), 1998 a) ul 1950 third edition, underwriters laboratories , inc. jan. 28, 1995. standard for safety of information technology equip ment including electrical business equipment. b) can/csa c22.2 no. 950-95 third edition, canadian standards association, jan. 28, 1995. standard for safety of information technology equip ment including electrical business equipment. c) en 60950 : 1992+a1: 1993+a2: 1993+a3: 1995+a1: 1 997+a11: 1997 iec 950 : 1991+a1: 1992+a2: 1993+a3: 1995+a1: 1996 european committee for electrotechnical standardizat ion(cenelec) european standard for safety of information technol ogy equipment including electrical business equipment. www..net www..net product specification 25/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 8. packing 8-2. packing form a) package quantity in one box : 30 pcs b) box size : 490mm x 393mm x 287mm 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m a,b,c : size(inch) d : year e : month f ~ m : serial no. note 1. year 2. month mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 3 2 1 dec mar feb jan b) location of lot mark serial no. is printed on the label. the label is at tached to the backside of the lcd module. this is subject to change without prior notice. www..net www..net product specification 26/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1. mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to the module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit b reak by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer s with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials l ike chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lo wer temperature, it becomes longer.) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time(required ti me that brightness is stable after turned on) becom es longer. (4) be careful for condensation at sudden temperatu re change. condensation makes damage to polarizer o r electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference sha ll be done by system manufacturers. grounding and shieldi ng methods may be important to minimized the interference. www..net www..net product specification 27/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through w rist band etc. and dont touch interface pin direct ly. 9-3. electrostatic discharge control strong light exposure causes degradation of polariz er and color filter. 9-4. precautions for strong light exposure 9-5. storage (1) when the protection film is peeled off, static electricity is generated between the film and polar izer. this should be peeled off slowly and carefully by p eople who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) the protection film is attached to the polarize r with a small amount of glue. if some stress is ap plied to rub the protection film against the polarizer du ring the time you peel off the film, the glue is apt to remain on the polarizer. please carefully peel off the protection film witho ut rubbing it against the polarizer. (3) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the polarizer af ter the protection film is peeled off. (4) you can remove the glue easily. when the glue r emains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cot ton waste or other soft material like chamois soaked with normal-hexane. 9-6. handling precautions for protection film when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the temperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that they be stored in the contai ner in which they were shipped. www..net www..net product specification 28/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 byte (dec) byte (hex) field name and comments value (hex) value (bin) 0 00 header 00 00000000 1 01 header ff 11111111 2 02 header ff 11111111 3 03 header ff 11111111 4 04 header ff 11111111 5 05 header ff 11111111 6 06 header ff 11111111 7 07 header 00 00000000 8 08 eisa manufacture code ( 3 character id ) lpl 32 00110010 9 09 eisa manufacture code (compressed asc ) 0c 00001100 10 0a panel supplier reserved - product code 0140h 40 01000000 11 0b ( hex. lsb first ) 01 00000001 12 0c lcd module serial no - preferred but optional ("0" if not used) 00 00000000 13 0d lcd module serial no - preferred but optional ("0" if not used) 00 00000000 14 0e lcd module serial no - preferred but optional ("0" if not used) 00 00000000 15 0f lcd module serial no - preferred but optional ("0" if not used) 00 00000000 16 10 week of manufacture : 00 weeks 00 00000000 17 11 year of manufacture 2008 year 12 00010010 18 12 edid structure version # = 1 01 00000001 19 13 edid revision # = 3 03 00000011 20 14 video input definition = digital signal, 6 bit _ de ll only 90 10010000 21 15 max h image size (rounded cm) = 30 cm 1e 00011110 22 16 max v image size (rounded cm) = 19 cm 13 00010011 23 17 display gamma = (gamma*100)-100 = example:(2.2*100) -100=120 = 2.2 gamma 78 01111000 24 18 feature support (no_dpms, no_active off/very low po wer, rgb color display, timing blk 1,no_ gtf) 0a 00001010 25 19 red/green low bits (rxry/gxgy) d7 11010111 26 1a blue/white low bits (bxby/wxwy) 85 10000101 27 1b red x rx = 0.577 93 10010011 28 1c red y ry =0.349 59 01011001 29 1d green x gx = 0.329 54 01010100 30 1e green y gy =0.55 8c 10001100 31 1f blue x bx = 0.162 29 00101001 32 20 blue y by = 0.133 22 00100010 33 21 white x wx =0.313 50 01010000 34 22 white y wy =0.329 54 01010100 35 23 established timing 1 (00h if nt used) 00 00000000 36 24 established timing 2 (00h if nt used) 00 00000000 37 25 manufacturer's timings (00h if nt used) 00 00000000 38 26 standard timing id1 (01h if not used) 01 00000001 39 27 standard timing id1 (01h if not used) 01 00000001 40 28 standard timing id2 (01h if not used) 01 00000001 41 29 standard timing id2 (01h if not used) 01 00000001 42 2a standard timing id3 (01h if not used) 01 00000001 43 2b standard timing id3 (01h if not used) 01 00000001 44 2c standard timing id4 (01h if not used) 01 00000001 45 2d standard timing id4 (01h if not used) 01 00000001 46 2e standard timing id5 (01h if not used) 01 00000001 47 2f standard timing id5 (01h if not used) 01 00000001 48 30 standard timing id6 (01h if not used) 01 00000001 49 31 standard timing id6 (01h if not used) 01 00000001 50 32 standard timing id7 (01h if not used) 01 00000001 51 33 standard timing id7 (01h if not used) 01 00000001 52 34 standard timing id8 (01h if not used) 01 00000001 53 35 standard timing id8 (01h if not used) 01 00000001 header vendor / product display vendor / product established standard timing id www..net www..net product specification 29/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 byte (dec) byte (hex) field name and comments value (hex) value (bin) 54 36 pixel clock/10,000 (lsb) 101.6 mhz @ 60.15hz b0 10110000 55 37 pixel clock/10,000 (msb) 27 00100111 56 38 horizontal active (lower 8 bits) 1440 pixels a0 10100000 57 39 horizontal blanking(thp-ha) (low er 8 bits) 38 4 pixels 80 10000000 58 3a horizontal active / horizontal blanking(thp-ha) (up per 4:4bits) 51 01010001 59 3b vertical avtive 900 lines 84 10000100 60 3c vertical blanking (tvp-ha) (de blanking typ.for de only panels) 26 lines 1a 00011010 61 3d vertical active : vertical blanking (tvp-ha) (up per 4:4bits) 30 00110000 62 3e horizontal sync. offset (thfp) 48 pixels 30 00110000 63 3f horizontal sync pulse width (hspw) 32 pixels 20 00100000 64 40 vertical sync offset(tvfp) : sync width (vspw) 3 lines : 6 lines 36 00110110 65 41 horizontal vertical sync offset/width (upp er 2bits) 00 00000000 66 42 horizontal image size (mm) 304 mm 30 00110000 67 43 vertical image size (mm) 190 mm be 10111110 68 44 horizontal image size / vertical image size 10 00010000 69 45 horizontal border = 0 (zero for notebook lcd) 00 00000000 70 46 vertical border = 0 (zero for notebook lcd) 00 00000000 71 47 non-interlace, normal display, no stereo, digital s eparate ( vsync_neg, hsync_pos ) 1a 00011010 72 48 pixel clock/10,000 (lsb) 67.86 mhz @ 40.18hz 82 10000010 73 49 pixel clock/10,000 (msb) 1a 00011010 74 4a horizontal active (lower 8 bits) 1440 pixels a0 10100000 75 4b horizontal blanking(thp-ha) (low er 8 bits) 38 4 pixels 80 10000000 76 4c horizontal active / horizontal blanking(thp-ha) (up per 4:4bits) 51 01010001 77 4d vertical avtive 900 lines 84 10000100 78 4e vertical blanking (tvp-ha) (de blanking typ.for de only panels) 26 lines 1a 00011010 79 4f vertical active : vertical blanking (tvp-ha) (up per 4:4bits) 30 00110000 80 50 horizontal sync. offset (thfp) 48 pixels 30 00110000 81 51 horizontal sync pulse width (hspw) 32 pixels 20 00100000 82 52 vertical sync offset(tvfp) : sync width (vspw) 3 lines : 6 lines 36 00110110 83 53 horizontal vertical sync offset/width (upp er 2bits) 00 00000000 84 54 horizontal image size (mm) 304 mm 30 00110000 85 55 vertical image size (mm) 190 mm be 10111110 86 56 horizontal image size / vertical image size 10 00010000 87 57 horizontal border = 0 (zero for notebook lcd) 00 00000000 88 58 vertical border = 0 (zero for notebook lcd) 00 00000000 89 59 non-interlace, normal display, no stereo, digital s eparate ( vsync_neg, hsync_pos ) 1a 00011010 90 5a flag 00 00000000 91 5b flag 00 00000000 92 5c flag 00 00000000 93 5d data type tag : alphanumeric data string (ascii str ing) fe 11111110 94 5e flag 00 00000000 95 5f dell p/n 1st character = c 43 01000011 96 60 dell p/n 2nd character = t 54 01010100 97 61 dell p/n 3rd character = 0 30 00110000 98 62 dell p/n 4th character = 0 30 00110000 99 63 dell p/n 5th character = 8 38 00111000 100 64 edid revision build name = st (cs) , revision # = x20 14 00010100 101 65 manufacturer p/n = 1 31 00110001 102 66 manufacturer p/n = 4 34 00110100 103 67 manufacturer p/n = 1 31 00110001 104 68 manufacturer p/n = w 57 01010111 105 69 manufacturer p/n = p 50 01010000 106 6a manufacturer p/n = 2 32 00110010 107 6b manufacturer p/n(if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 0a 00001010 timing descriptor #3 timing descriptor #1 timing descriptor #2 www..net www..net product specification 30/ 30 lp141wp2 liquid crystal display ver. 0.0 22, apr, 2008 byte (dec) byte (hex) field name and comments value (hex) value (bin) 108 6c flag 00 00000000 109 6d flag 00 00000000 110 6e flag 00 00000000 111 6f data type tag : descriptor defined by manufacturer 00 00000000 112 70 flag 00 00000000 113 71 smbus value(step #1) = 0 nits 00 00000000 114 72 smbus value(step #2) = 0 nits 00 00000000 115 73 smbus value(step #3) = 0 nits 00 00000000 116 74 smbus value(step #4) = 0 nits 00 00000000 117 75 smbus value(step #5) = 0 nits 00 00000000 118 76 smbus value(step #6) = 0 nits 00 00000000 119 77 smbus value(step #7) = 0 nits 00 00000000 120 78 smbus value(step #8) = 0 nits (typically = ffh, max nits) 00 00000000 121 79 dual channel lvds, no rtc support 02 00000010 122 7a bist support 01 00000001 123 7b (if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 0a 00001010 124 7c (if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 20 00100000 125 7d (if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 20 00100000 126 7e extension flag (# of optional 128 panel id extensio n block to follow, typ = 0) 00 00000000 127 7f check sum (the 1-byte sum of all 128 bytes in this panel id block shall = 0) d3 11010011 timing descriptor #4 checksum www..net www..net |
Price & Availability of LP141WP2-TLA1
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |