-0- no. stse-cc6120a specifications for nichia chip type green led model : NHSG017HT nichia corporation
-1- nichia stse-cc6120a 1.specifications (1) absolute maximum ratings (ta=25c) item symbol absolute maximum rating unit forward current i f 10 ma pulse forward current i fp 30 ma allowable reverse current i r 85 ma power dissipation p d 36 mw operating temperature t opr -40 ~ +100 c storage temperature t stg -40 ~ +100 c soldering temperature t sld reflow soldering : 260c for 10sec. dip soldering : 260c for 10sec. hand soldering : 350c for 3sec. i fp conditions : pulse width 10msec. and duty 1/10 (2) initial electrical/optical characteristics (ta=25c) item symbol condition typ. max. unit forward voltage v f i f =5[ma] (3.1) 3.6 v luminous intensity iv i f =5[ma] (115) - mcd x - i f =5[ma] 0.17 - - chromaticity coordinate y - i f =5[ma] 0.70 - - please refer to cie 1931 chromaticity diagram. (3) ranking (ta=25c) item symbol condition min. max. unit rank r iv i f =5[ma] 140 195 mcd rank q iv i f =5[ma] 98 140 mcd luminous intensity rank p iv i f =5[ma] 70 98 mcd luminous intensity measurement allowance is 10%. color ranks (i f =5ma,ta=25c) rank g rank h x 0.14 0.14 0.22 0.22 x 0.21 0.21 0.28 0.28 y 0.64 0.74 0.74 0.64 y 0.65 0.73 0.73 0.65 color coordinates measurement allowance is 0.01. one delivery will include up to two color ranks a nd three luminous intensity ranks of the products. the quantity-ratio of the ranks is decided by nichia. < = < =
-2- nichia stse-cc6120a 2.initial optical/electrical characteristics please refer to figure?s page. 3.outline dimensions and materials please refer to figure?s page. material as follows ; package : heat-resistant polymer encapsulating resin : epoxy resin (with diffused) electrodes : ag plating copper alloy 4.packaging the leds are packed in cardboard boxes after taping. please refer to figure?s page. the label on the minimum packing unit shows ; part number, lot number, ranking, quantity in order to protect the leds from mechanical shock, we pack them in cardboard boxes for transportation. the leds may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. the boxes are not water resistant and therefore must be kept away from water and moisture. when the leds are transported, we recommend that you use the same packing method as nichia. 5.lot number the first six digits number shows lot number . the lot number is composed of the following characters; - u - year ( 5 for 2005, 6 for 2006 ) - month ( 1 for jan., 9 for sep., a for oct., b for nov. ) - nichia's product number u - ranking by color coordinates - ranking by luminous intensity
-3- nichia stse-cc6120a 6.reliability (1) test items and results test item standard test method test conditions note number of damaged resistance to soldering heat (dip soldering) jeita ed-4701 300 301 tsld=260c, 10sec. (pre treatment 30c,70%,168hrs.) 1 time 0/22 solderability (dip soldering) jeita ed-4701 300 303 tsld=235 5c, 2sec. (using flux) 1 time over 95% 0/22 resistance to soldering heat (reflow soldering) jeita ed-4701 300 301 tsld=260c, 10sec. (pre treatment 30c,70%,168hrs.) 2 times 0/22 solderability (reflow soldering) jeita ed-4701 300 303 tsld=215 5c, 3sec. (using flux, lead solder) 1 time over 95% 0/22 thermal shock jeita ed-4701 300 307 -40c ~ 100c 1min. (10sec.) 1min. (pre treatment 30c,70%,168hrs.) 100 cycles 0/100 temperature cycle jeita ed-4701 100 105 -40c ~ 25c ~ 100c ~ 25c 30min. 5min. 30min. 5min. 100 cycles 0/100 moisture resistance cyclic jeita ed-4701 200 203 25c ~ 65c ~ -10c 90%rh 24hrs./1cycle 10 cycles 0/100 high temperature storage jeita ed-4701 200 201 ta=100c 1000 hrs. 0/100 temperature humidity storage jeita ed-4701 100 103 ta=60c, rh=90% 1000 hrs. 0/100 low temperature storage jeita ed-4701 200 202 ta=-40c 1000 hrs. 0/100 steady state operating life ta=25c, i f =10ma 1000 hrs. 0/100 steady state operating life of high temperature ta=85c, i f =10ma 1000 hrs. 0/100 steady state operating life of high humidity heat 60c, rh=90%, i f =10ma 1000 hrs. 0/100 steady state operating life of low temperature ta=-40c, i f =5ma 1000 hrs. 0/100 permanence of marking jeita ed-4701 500 501 solvent : isopropyl alcohol solvent temperature : 20 ~ 25c dipping time : 5 min. 1 time 0/22 vibration jeita ed-4701 400 403 100 ~ 2000 ~ 100hz sweep 4min. 200m/s 2 3direction, 4cycles 48min. 0/10 drop 75cm 3 times 0/10 electrostatic discharge jeita ed-4701 300 304 r=1.5k ? , c=100pf test voltage=2kv 3 times negative/positive 0/22 (2) criteria for judging damage criteria for judgement item symbol test conditions min. max. forward voltage v f i f =5ma - u.s.l.*) 1.1 luminous intensity condition 1 i v i f =5ma l.s.l.**) 0.7 - luminous intensity condition 2 i v i f =5ma l.s.l.**) 0.5 - *) u.s.l. : upper standard level **) l.s.l. : lower standard level these test items are judged by the criteria of luminous intensity condition 2.
-4- nichia stse-cc6120a 7.cautions (1) moisture proof package when moisture is absorbed into the smt package it may vaporize and expand during soldering. there is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the leds. for this reason, th e moisture proof package is used to keep moisture to a minimum in the package. the moisture proof package is made of an aluminum moisture proof bag. a package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. the silica gel changes its color from blue to pink as it absorbs moisture. (2) storage storage conditions before opening the package : the leds should be kept at 30c or less and 90%rh or less. the leds should be used within a year. when storing the leds, moisture proof packaging with absorbent material (silica gel) is recommended. after opening the package : the leds should be kept at 30c or less and 70%rh or less. the leds should be soldered within 168 hours (7days) after opening the package. if unused leds remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). it is also recommended to return the leds to the original moisture proof bag and to reseal the moisture proof bag again. if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : more than 24 hours at 65 5c nichia led electrodes are silver plated copper alloy. the silver surface may be affected by environments which contain corrosive substances. please avoid conditions which may cause the led to corrode, tarnish or discolor. this corrosion or discoloration may cause difficulty during soldering operations. it is recommended that the user use the leds as soon as possible. please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) heat generation thermal design of the end product is of paramount importance. please consider the heat generation of the led when making the system design. the coefficient of temperature increase per input electric power is affected by the thermal resistan ce of the circuit board and density of led placement on the board, as well as other components. it is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. the operating current should be decided after considering the ambient maximum temperature of leds.
-5- nichia stse-cc6120a (4) soldering conditions the leds can be soldered in place using the reflow soldering method and the dip soldering method. recommended soldering conditions reflow soldering dip soldering hand soldering lead solder lead-free solder pre-heat pre-heat time peak temperature soldering time condition 120 ~ 150c 120 sec. max. 240c max. 10 sec. max. refer to temperature - profile 1 . 180 ~ 200c 120 sec. max. 260c max. 10 sec. max. refer to temperature - profile 2 . (n 2 reflow is recommended.) pre-heat pre-heat time solder bath temperature dipping time 100c max. 60 sec. max. 260c max. 10 sec. max. temperature soldering time 350c max. 3 sec. max. (one time only) although the recommended soldering conditions are speci fied in the above table, reflow, dip or hand soldering at the lowest possible temperature is desirable for the leds. a rapid-rate process is not recommended for cooling the leds down from the peak temperature. [temperature-profile (surface of circuit board)] use the conditions shown to the under figure. [recommended soldering pad design] use the following conditions shown in the figure. occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. it is recommended that the user use the nitrogen reflow method. repairing should not be done after the leds have been soldered. when repairing is unavoidable, a double-head soldering iron should be used. it should be confirmed beforehand whether the characteristics of the leds will or will not be damaged by repairing. reflow soldering should not be done more than two times. dip soldering should not be done more than one time. when soldering, do not put stress on the leds during heating. after soldering, do not warp the circuit board. 60sec.max. above 220 c 120sec.max. pre-heating 260c max. 10sec. max. 1~ 5c / sec. 1~ 5c / sec. 180 ~ 200c < 1 : lead solder> < 2 : lead-free solder> 60sec.max. above 200 c 120sec.max. pre-heating 240c max. 10sec. max. 2.5 ~ 5c / sec. 2.5 ~ 5c / sec. 120 ~ 150c : solder resist 4 4 9.5 2.6 1.5 4 1.5 (unit : mm)
-6- nichia stse-cc6120a (5) cleaning it is recommended that isopropyl alcohol be used as a solvent for cleaning the leds. when using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. freon solvents should not be used to clean the leds because of worldwide regulations. do not clean the leds by the ultrasonic. when it is absolutely necessary, the influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the assembled condition. before cleaning, a pre-test should be done to confirm whether any damage to the leds will occur. (6) static electricity static electricity or surge voltage damages the leds. it is recommended that a wrist band or an anti-electrostatic glove be used when handling the leds. all devices, equipment and machinery must be properly grounded. it is recommended that precautions be taken against surge voltage to the equipment that mounts the leds. when inspecting the final products in which leds were assembled, it is recommended to check whether the assembled leds are damaged by static electricity or not. it is easy to find static-damaged leds by a light-on test or a vf test at a lower current (below 1ma is recommended). damaged leds will show some unusual characteristics such as the forward voltage becomes lower, or the leds do not light at the low current. criteria : (v f > 2.0v at i f =0.5ma) (7) others nhsg017h complies with rohs directive. the led light output is strong enough to injure human eyes. precautions must be taken to prevent looking directly at the leds with unaided eyes for more than a few seconds. flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. also, people should be cautious when using equipment that has had leds incorporated into it. the leds described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). consult nichia?s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). user shall not reverse engineer by disassembling or analysis of the leds without having prior written consent from nichia. when defective leds are found, the user shall inform nichia directly before disassembling or analysis. the formal specifications must be exchanged and signed by both parties before large volume purchase begins. the appearance and specifications of the product may be modified for improvement without notice.
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 500 510 520 530 540 550 g h 490 480 470 460 560 570 580 590 600 610 620 630 x y ici chromaticity diagram -7- ? color coordinates measurem ent allowance is 0.01. nichia stse-cc6120a
0306090120 -60 -30 0306090120 -60 -30 4.0 3.7 3.4 2.8 2.5 2.2 3.1 2.5 2.8 3.1 3.4 3.7 4.0 4.0 3.0 2.5 1.5 1.0 0.5 0 2.0 3.5 allowable forward current i f (ma) relative luminosity (a.u.) relative luminosity (a.u.) forward current i fp (ma) allowable forward current i fp (ma) ambient temperature vs. allowable forward current ambient temperature ta (c ) ambient temperature vs. relative luminosity ambient temperature ta ( c ) ambient temperature vs. forward voltage ambient temperature ta ( c ) forward voltage v f (v) duty ratio (%) forward current vs. relative luminosity forward current i fp (ma) forward voltage v f (v) forward voltage vs. forward current duty ratio vs. allowable forward current 100 50 30 10 5 1 010203040 1 51020 100 50 ta=25c ta=25c ta=25c i fp =5ma i fp =5ma 80 100 120 40 020 60 100 30 1 5 10 50 15.0 12.5 10.0 0 7.5 5.0 2.5 -8- n ichia stse -c c6120a characteristics model nhsg017h nichia corporation title no. 060927656781 2.0 1.0 0.5 0.2
0306090120 -60 -30 1ma(527nm) 5ma(525nm) 10ma(523nm) 30ma(519nm) 400 450 500 550 650 700 600 0.12 0.14 0.16 0.18 0.20 0.22 0.74 0.72 0.70 0.68 0.66 0.64 531 527 525 519 529 523 521 531 529 523 517 525 521 519 527 dominant wavel ength d (nm) dominant wavel ength d (nm) directivity radiation angle 0 10 20 30 40 50 60 70 80 90 1.0 0.5 0 spectrum forward current vs. chromaticity coordinate ( d ) ambient temperature vs. dominant wavelength forward current vs. dominant wavelength y relative emission intensity (a.u.) forward current i fp (ma) ambient temperature ta (c) xx wavelength (nm) relative luminosity (a.u.) 1 5 10 30 100 50 1.2 1.0 0.8 0.4 0.2 0 0.6 ta=25c ta=25c i f =5ma i fp =5ma 0 30 0.5 90 60 1.0 ta=25c ta=25c i fp =5ma -9- n ichia stse-cc6120a characteristics model nhsg017h nichia corporation title no. 060927656791
internal circuit (0.4) anode cathode 2 0.3 (0.8) 2.2 (1.05) (0.45) 3.5 0.3 (1.9) 0.8 0.3 0.8 0.3 a k protection device cathode mark (c 0.6) (2.4) 2.8 (2.4) 3.2 item materials package heat-resistant polymer encapsulating resin epoxy resin (with diffused) electrodes ag plating copper alloy ? nxsg017x has a protection device built in as a protection circuit against static electricity. -10- nichia stse-cc6120a uni t mm allow nichia corporation n o. outline dimensions 060927539142 title model n xsg017x 0.2 scal e 15/1
taping is based on the jis c 0806 : packaging of electronic components on continuous tapes. 2,000pcs/reel cathode mark xxxx led type nxsx017xt lot xxxxxx- u ? qty pcs taping part reel end of tape label reel part no leds top cover tape reel lead min.40mm (no leds) pull direction leds mounting part no leds reel lead min.400mm embossed carrier tape reel lead min.160mm (no leds is more than 40) 1.75 0.1 4 0.1 4 0.1 2 0.05 3.5 0.05 (2.75) 0.25 0.05 2.15 0.1 3.65 0.1 60 +1 -0 11.4 1 9 0.3 1 3 0 . 2 2 1 0 . 8 2.85 0.1 180 +0 -3 1 +0.25 -0 8 +0.3 -0.1 1.5 +0.1 -0 nichia stse-cc6120a -11- unit mm nichia corporation n o. taping dimensions 060927537832 title model n xsx017xt allow scale
the reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. label the box is partitioned with the cardboard . moisture absorbent material packing unit reel/bag quantity/bag (pcs) moisture proof foil bag 1reel 2,000 max. cardboard box dimensions (mm) reel/box quantity/box (pcs) cardboard box s 291 237 120 8t 7reel max. 14,000 max. cardboard box m 259 247 243 5t 15reel max. 30,000 max. cardboard box l 444 262 259 8t 30reel max. 60,000 max. label xxxx led type nxsx017xt lot xxxxxx- u ? qty pcs nichia corporation 491 oka, kaminaka, anan, tokushima, japan n ichia xxxx led type nxsx017xt rank u ? qty pcs nichia corporation 491 oka, kaminaka, anan, tokushima, japan n ichia seal moisture proof foil bag n ichia led reel -12- nichia corporation n o. packing 060927540702 title model nxsx017xt nichia stse-cc6120a
|
