![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www..com Product Description: T315XW02 TFT-LCD PANEL AUO Model Name: T315XW02 V9 Customer Part No/Project Name: Customer Signature Date AUO Approved By: PL Chen Reviewed By: Hong Jye Hong Prepared By: Jacky Su Date (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 1/28 www..com Document Version : 0 Date : 2006/08/30 Product Specifications 31.5" WXGA Color TFT-LCD Module Model Name: T315XW02 V9 (*) Preliminary Specifications ( ) Final Specifications (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 2/28 www..com Contents No COVER CONTENTS RECORD OF REVISIONS 1 2 3 GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS 3-1 3-2 3-3 3-4 3-5 3-6 4 5 6 7 7-1 7-2 8 9 ELECTRICAL CHARACTREISTICS INTERFACE CONNECTIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERNECE POWER SEQUENCE OPTICAL SPECIFICATIONS MECHANICAL CHARACTERISTICS RELIABLITY INTERNATIONAL STANDARDS SAFETY EMC PACKING PRECAUTIONS (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 3/28 www..com Record of Revision Version 0 Date 2006/08/30 No First issue Old Description New Description Remark (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 4/28 w w w . 1. General Description This specification applies to the 31.51 inch Color TFT-LCD Module T315XW02 V9. This LCD module has a TFT active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 31.51 inch. This module supports 1366x768 XGA-WIDE mode (Non-interlace). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot. The T315XW02 V9 has been designed to apply the 8-bit 1 channel LVDS interface method. It is intended to support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important. * General Information Items Active Screen Size Display Area Outline Dimension Driver Element Display Colors Number of Pixels Pixel Pitch Pixel Arrangement Display Mode Surface Treatment Specification 31.51 inches 697.685 (H) x 392.256(V) 760.0(H) x 450.0(V) x 45(D) a-Si TFT active matrix 16.7M 1366 x 768 0.51075 RGB vertical stripe Normally Black AG, 3H Unit mm mm Note With inverter Colors Pixel mm (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 5/28 www..com 2. Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause permanent damage to the unit. Item Logic/LCD Drive Voltage Input Voltage of Signal BLU Input Voltage BLU Brightness Control Voltage Operating Temperature Operating Humidity Storage Temperature Storage Humidity Panel Surface Temperature Note 1: Duration:50 msec. Symbol Vcc Vin VDDB Vdim TOP HOP TST HST PST Min -0.3 -0.3 -0.3 -0.3 0 10 -20 10 Max 7.0 3.6 28 7.0 +50 90 +60 90 65 Unit [Volt] [Volt] [Volt] [Volt] [ C] [%RH] [ C] [%RH] [ C] o o o Conditions Note 1 Note 1 Note 1 Note 1 Note 2 Note 2 Note 2 Note 2 Note 2 : Maximum Wet-Bulb should be 39 and No condensation. The relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. At temperatures greater than 40, the wet bulb temperature must not exceed 39. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 6/28 w w w 3. Electrical Specification The T315XW02 V1 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the BLU, is to power inverter.. 3-1 Electrical Characteristics Parameter Min Values Typ Max Unit Notes LCD: Power Voltage Power Current Power Consumption Inrush Current LVDS Interface Differential Input High Threshold Voltage Differential Input Low Threshold Voltage Common Voltage Input Supply Input Vcc 4.5 5.0 5.5 Vdc 1 Supply Input Icc - 1.2 1.5 A 2 Pc IRUSH VTH - 6.0 - 7.5 TBD +100 Watt Apeak mV 2 3 4 VTL -100 mV 4 VCIM 1.10 1.25 1.40 V 4 CMOS Interface Input High Threshold Voltage Input Low Threshold Voltage VIH (High) VIL (Low) PDDB 2.4 3.3 Vdc 0 0.7 Vdc Backlight Power Consumption Life Time 78 87 96 Watt 5,6 60,000 Hours 7 Note : 1. 2. The ripple voltage should be controlled under 10% of VCC Vcc=5.0V, f v = 60Hz, fCLK=81.5Mhz , 25, Test Pattern : White Pattern Specs. ver 0 7/28 (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed www..com 3. Measurement condition : VCC 90% 10% GND Trush = 470 uS 4. VCIM = 1.2V VTH VCIM VTL 0V 5. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC Inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly should be operated in the same condition as installed in your instrument. 6. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape, TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape. 7. The relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. At temperatures greater than 40, the wet bulb temperature must not exceed 39. When operate at low temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 8/28 www..com 3-2 Interface Connections LCD connector (CN3): JAE FI-E30S or equivalent. AUO will notice Toshiba if we change the LCD connector from JAE to others. LVDS Transmitter: DS90C385 (NS) or equivalent Symbol Reserved Reserved Reserved GND RIN0RIN0+ GND RIN1RIN1+ GND RIN2RIN2+ GND RCLKRCLK+ GND RIN3RIN3+ GND Reserved Open or High Open or High Open or High Ground and Signal Return LVDS Channel 0 negative LVDS Channel 0 positive Ground and Signal Return for LVDS LVDS Channel 1 negative LVDS Channel 1 positive Ground and Signal Return for LVDS LVDS Channel 2 negative LVDS Channel 2 positive Ground and Signal Return for LVDS LVDS Clock negative LVDS Clock positive Ground and Signal Return for LVDS LVDS Channel 3 negative LVDS Channel 3 positive Ground and Signal Return Open or High Auo internal test pin Description note Auo internal test pin Auo internal test pin Auo internal test pin Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 LVDS Option Low for JEIDA, High/Open for NS Reserved GND GND GND Vcc Vcc Vcc Vcc Vcc Open Ground and Signal Return Ground and Signal Return Ground and Signal Return 5V, DC, Regulated 5V, DC, Regulated 5V, DC, Regulated 5V, DC, Regulated 5V, DC, Regulated Note: 1. All GND (ground) pins should be connected together and should also be connected to the LCD's metal (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 - Specs. ver 0 9/28 No Reproduction and Redistribution Allowed www..com frame. All Vcc (power input) pins should be connected together. LVDS Option = L (GND) LVDS Option = H (3.3V) or Open (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 10/28 www..com BACKLIGHT CONNECTOR PIN CONFIGURATION 1. Electrical specification Item Input Voltage Input Current (Stable Condition) Input Power (Stable Condition) Inrush Current On/Off Control Voltage On/Off Control Current Dimming Control Current Symb. VDDB IDDB PDDB IRUSH VBLON IBLON VDIM MAX MIN ON OFF Condition --VDDB=24V VDDB=24V VDDB=24V VDDB=24V VDDB=24V VDDB=24V VDDB=24V VDDB=24V Spec Min 21.6 3.24 78.0 --2.0 0.0 0.0 ----Typ 24.0 3.60 87 --------3.3 0.0 Max 26.4 3.96 96 6.0 5.0 0.8 1.5 ----Unit VDC ADC W ADC VDC mADC VDC Note 1 1 1,2 Note1 : VDIM= 3.3V (MAX) Ta=255 , Turn on for 45minutes Note 2 : Measurement condition Rising time = 20 ms (VDDB : 10%~90%); 2. Input specification CN1: No 1 2 3 4 5 6 7 8 9 10 11 12 13 JST PHR-14 or equivalent Symbol VDDB (Main Power) VDDB (Main Power) VDDB (Main Power) VDDB (Main Power) VDDB (Main Power) GND GND GND GND GND Reserved VBLON (Enable Pin) VDIM (LCD Bright) Description DC input 24.0 VDC DC input 24.0 VDC DC input 24.0 VDC DC input 24.0 VDC DC input 24.0 VDC Ground Ground Ground Ground Ground Please leave it Open. On/Off control Signal; High: On; Low: Off Internal PWM Dimming control signal input (DC 0~3.3V) (3.3V : Maximum brightness, 0V min brightness) 14 Reserved Please leave it Open. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 11/28 www..com 3-3 Signal Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it's proper operation. * Timing Table DE only Mode Vertical Frequency: Notes: 1.) Display position is specific by the rise of DE signal only. Horizontal display position is specified by the rising edge of 1st DCLK after the rise of 1st DE, is displayed on the left edge of the screen. Vertical display position is specified by the rise of DE after a "Low" level period equivalent to eight times of horizontal period. The 1st data corresponding to one horizontal line after the rise the of 1st DE is displayed at the top line of screen. 3.) If a period of DE "High" is less than 1366 DCLK or less than 768 lines, the rest of the screen displays black. 4.) The display position does not fit to the screen if a period of DE "High" and the effective data period do not synchronize with each other. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. ver 0 12/28 www..com Tv Tdisp(v) Th DE RGB Data 768 Line Invalid Data 1 Line 2 Line 3 Line 4 Line 768 Line Invalid Data CLK Th Tdisp(h) Tclk DE RGB Data Pixel 1366 Invalid Data Pixel 1 Pixel 2 Pixel 3 Pixel 4 Pixel 5 Pixel 6 Pixel 1366 Invalid Data Pixel 1 Pixel 2 (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed 3-4 Signal Timing Waveforms - Specs. Ver 0 13/28 www..com 3-5 Color Input Data Reference The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input. COLOR DATA REFERENCE Input Color Data Color MSB RED LSB MSB GREEN LSB MSB BLUE LSB R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 Black Red(255) Green(255) Basic Color Blue(255) Cyan Magenta Yellow White RED(000) RED(001) RED ---RED(254) RED(255) 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 1 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 GREEN(000) 0 GREEN(001) 0 GREEN ---GREEN(254) 0 GREEN(255) 0 BLUE(000) BLUE(001) BLUE ------BLUE(254) BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 14/28 www..com 3-6 Power Sequence for LCD Module 3.6.1 Power Sequence for LCD Power Supply For LCD Vcc (+5V) 90% 10% GND t1 t2 90% 10% 10% Interface Signal (LVDS data & CLK) t5 t6 t7 GND 10% Valid Data 10% Backlight on/off control signal (VBLON) t3 t4 Parameter Min. t1 t2 t3 t4 t5 t6 t7 1 0.4 0.5 500 10 0.5 Values Typ. Max. 20 50 50 300 - Units ms ms ms ms ms ms s *1 If t3=200ms, input black signal till 700ms from system if necessary In case of t3<200ms, the abnormal display will be happened. But it will not damage timing controller. Note: The timing controller will not be damaged in case of TV set AC input power suddenly shut down. Once power reset, it should follow power sequence as spec. definition. (1) Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD operation or the LCD turns off before the back-light turns off, the display may momentarily become abnormal screen. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 15/28 www..com 3.6.2 Power Sequence for Inverter Parameter Min. T1 T2 T3 T4 T5 T6 20 50 0 0 0 - Values Typ. Max. 10 Units ms ms ms ms ms ms (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 16/28 www..com 4. Optical Specification Optical characteristics are determined after the unit has been `ON' and stable for approximately 45 minutes in a dark environment at 25. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. Fig.1 1 presents additional information concerning the measurement equipment and method. Parameter Contrast Ratio Surface Luminance, white Luminance Variation Response Gray to Gray time Color Gamut Color Coordinates RED Symbol Min. CR LWH WHITE 9p 1200 400 Values Typ. 1500 500 1.40 8 Max. Units Notes 1 cd/ 2 3 ms 4 T NTSC 72 % RX RY 0.64 0.33 0.29 0.60 Typ.-0.03 0.15 0.06 0.28 0.29 Typ.+0.03 GREEN GX GY BLUE BX BY WHITE WX WY Viewing Angle x axis, right(=0) x axis, left(=180) y axis, up(=90) y axis, down (=0) r l u d 89 89 89 89 Degree 6 (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 17/28 www..com Note: 1. Contrast Ratio (CR) is defined mathematically as: Surface Luminance of Lon1 Contrast Ratio= Surface Luminance of Loff1 2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all pixels displaying white. From more information see FIG 2. When VDDB = 24V, IDDB = 5A. Where Lon1 is the luminance with all pixels displaying white at center 1 location. LWH=Lon1 3. The variation in surface luminance, WHITE is defined (center of Screen) as: WHITE(9P)= Maximum(Lon1, Lon2,...,Lon9)/ Minimum(Lon1, Lon2,...Lon9) 4. Response time is the time required for the display to transition from black to white(Rise Time, TrR) and from white to black (Decay Time, TrD). For additional information see FIG3. 5. 6. T is the response time between any two gray scale and is based on fv=60Hz to optimize. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG4. FIG. 2 Luminance V H/2 1 2 3 4 5 6 H 7 8 H/6 V/6 V/2 (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 18/28 www..com FIG.3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for "any level of gray(bright) " and "any level of gray(dark)". Any level of gray(Bright) Any level of gray(Dark) Any level of gray(Bright) L0,15,L31,....L255 L0,15,L31,....L255 FIG.4 Viewing angle (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed Photodetector Output L0,15,L31,....L255 Time TrR - Specs. Ver 0 19/28 www..com 5. Mechanical Characteristics The contents provide general mechanical characteristics for the model T315XW02 V1. In addition the figures in the next page are detailed mechanical drawing of the LCD. Horizontal Outline Dimension Vertical Depth Bezel Opening Horizontal Vertical Active Display Area Horizontal Vertical Weight Surface Treatment 6500g Typ. AG, 3H 760.0mm 450.0mm 45mm 703.6mm 398.3mm 697.68mm 392.26mm (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 20/28 www..com Front: (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 21/28 www..com HIGH V OLTAGE CAUTIO N RISK OF ELECTRIC SHOCK. DISCONNEC T THE ELEC TRIC POWER BEFORE SERVICIN G. COL D C ATHOD E FLU OR ESC ENT L AMP IN L CD PANEL CONTAINS A SMAL L AMOU NT OF MER CUR Y PLEAS E FOLL OW L OCAL ORD IN ANC ES OR REGU LATIONS FOR DISPOSAL. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed Back: - Specs. Ver 0 22/28 www..com 6. Reliability: Environment test condition No 1 2 3 4 5 Test Item High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test Vibration test (non-operating) Condition Ta=60 300h Ta=-20 300h Ta=50 80%RH 300h Ta=0 300h Wave form: random Vibration level : 1.0G RMS Bandwidth : 10-500Hz Duration: X, Y, Z 20min One time each direction Shock level: 50G Waveform: half since wave, 11ms Direction: X, Y, Z One time each direction Random Vibration:10~200Hz,1.5G,30minutes in each X,Y,Z direction 6 Shock test (non-operating) 7 Vibration test (with carton) 8 Drop test (with carton) Height: 53.3cm 1 corner, 3 edges, 6 surfaces (ASTMD4169-I) (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 23/28 www..com 7. International Standard 7-1. Safety (1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995 Standard for Safety of Information Technology Equipment Including electrical Business Equipment. (2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association, Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. (3) EN60950 : 1992+A2: 1993+A2: 1993+C3: 1995+A4: 1997+A11: 1997 IEC 950: 1991+A1: 1992+A2: 1993+C3: 1995+A4:1996 European Committee for Electrotechnical Standardization (CENELEC) EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical Business Equipment. 7-2. EMC a) ANSI C63.4 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHz to 40GHz. "American National standards Institute(ANSI), 1992 b) C.I.S.P.R "Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment." International Special committee on Radio Interference. c) EN 55022 "Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment." European Committee for Electrotechnical Standardization. (CENELEC), 1998 (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 24/28 www..com 8. Packing Panel label: C US TW6562700014 TW65627: Production Lot 00014: Panel Serial Number ZMA: AUO internal code Manufactured 06/21: 2006 week 21 Made In Taiwan: Taiwan made Carton Label : (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 25/28 www..com Carton: (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 26/28 www..com 9. PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1 MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front/ rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength. 9-2 OPERATING PRECAUTIONS (1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage: V=200mV(Over and under shoot voltage) (2) Response time depends on the temperature. (In lower temperature, it becomes longer..) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimize the interface. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 27/28 www..com 9-3 ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don't touch interface pin directly. 9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE Strong light exposure causes degradation of polarizer and color filter. 9-5 STORAGE When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5 and 35 at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped. 9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM (1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of flue still on the Bezel after the protection film is peeled off. (3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. (c)Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. T315XW02 V9 No Reproduction and Redistribution Allowed - Specs. Ver 0 28/28 |
Price & Availability of T315XW02-V9
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |