![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
SX1211 Transceiver Ultra-Low Power Integrated UHF Transceiver ADVANCED COMMUNICATIONS & SENSING General Description The SX1211 is a low cost single-chip transceiver operating in the frequency ranges from 863-870, 902928 MHz and 950-960 MHz. The SX1211 is optimized for very low power consumption (3mA in receiver mode). It incorporates a baseband modem with data rates up to 200 kb/s. Data handling features include a sixty-four byte FIFO, packet handling, automatic CRC generation and data whitening. Its highly integrated architecture allows for minimum external component count whilst maintaining design flexibility. All major RF communication parameters are programmable and most of them may be dynamically set. It complies with European (ETSI EN 300-220 V2.1.1) and North American (FCC part 15.247 and 15.249) regulatory standards. Features Low Rx power consumption: 3mA Low Tx power consumption: 25 mA @ +10 dBm Good reception sensitivity: down to -107 dBm at 25 kb/s in FSK, -113 dBm at 2kb/s in OOK Programmable RF output power: up to +12.5 dBm in 8 steps Packet handling feature with data whitening and automatic CRC generation Wide RSSI (Received Signal Strength Indicator) dynamic range, 70dB from Rx noise floor Bit rates up to 200 kb/s, NRZ coding On-chip frequency synthesizer FSK and OOK modulation Incoming sync word recognition Built-in Bit-Synchronizer for incoming data and clock synchronization and recovery 5 x 5 mm TQFN package Optimized Circuit Configuration for Low-cost applications Ordering Information Table 1: Ordering Information Part number Delivery Minimum Order Quantity / Multiple Applications Wireless alarm and security systems Wireless sensor networks Automated Meter Reading Home and building automation Industrial monitoring and control Remote Wireless Control SX1211I084TRT Tape & Reel 3000 pieces SX1211I084T Tray 200 pieces TQFN-32 package - Operating range [-40;+85 C] T refers to Lead Free packaging This device is WEEE and RoHS compliant Application Circuit Schematic Rev 7- September 2nd, 2008 Page 1 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Table of Contents 1. General Description.................................................................. 5 1.1. Simplified Block Diagram ....................................................... 5 1.2. Pin Diagram........................................................................... 6 1.3. Pin Description ...................................................................... 7 2. Electrical Characteristics .......................................................... 8 2.1. ESD Notice............................................................................ 8 2.2. Absolute Maximum Ratings ................................................... 8 2.3. Operating Range ................................................................... 8 2.4. Chip Specification.................................................................. 8 2.4.1. Power Consumption ........................................................... 8 2.4.2. Frequency Synthesis .......................................................... 9 2.4.3. Transmitter ......................................................................... 9 2.4.4. Receiver ........................................................................... 10 2.4.5. Digital Specification .......................................................... 11 3. Architecture Description.......................................................... 12 3.1. Power Supply Strategy ........................................................ 12 3.2. Frequency Synthesis Description......................................... 13 3.2.1. Reference Oscillator ......................................................... 13 3.2.2. CLKOUT Output ............................................................... 13 3.2.3. PLL Architecture ............................................................... 14 3.2.4. PLL Tradeoffs ................................................................... 14 3.2.5. Voltage Controlled Oscillator............................................. 15 3.2.6. PLL Loop Filter ................................................................. 16 3.2.7. PLL Lock Detection Indicator ............................................ 16 3.2.8. Frequency Calculation ...................................................... 16 3.3. Transmitter Description........................................................ 18 3.3.1. Architecture Description.................................................... 18 3.3.2. Bit Rate Setting................................................................. 19 3.3.3. Alternative Settings........................................................... 19 3.3.4. Fdev Setting in FSK Mode ................................................ 19 3.3.5. Fdev Setting in OOK Mode ............................................... 19 3.3.6. Interpolation Filter............................................................. 20 3.3.7. Power Amplifier ................................................................ 20 3.3.8. Common Input and Output Front-End ............................... 22 3.4. Receiver Description............................................................ 23 3.4.1. Architecture ...................................................................... 23 3.4.2. LNA and First Mixer .......................................................... 24 3.4.3. IF Gain and Second I/Q Mixer........................................... 24 3.4.4. Channel Filters ................................................................. 24 3.4.5. Channel Filters Setting in FSK Mode ................................ 25 3.4.6. Channel Filters Setting in OOK Mode ............................... 26 3.4.7. RSSI................................................................................. 26 3.4.8. Fdev Setting in Receive Mode .......................................... 28 3.4.9. FSK Demodulator ............................................................. 28 3.4.10. OOK Demodulator .......................................................... 28 3.4.11. Bit Synchronizer ............................................................. 31 3.4.12. Alternative Settings......................................................... 32 3.4.13. Data Output .................................................................... 32 4. Operating Modes .................................................................... 33 4.1. Modes of Operation ............................................................. 33 4.2. Digital Pin Configuration vs. Chip Mode ............................... 33 5. Data Processing ..................................................................... 34 5.1. Overview ............................................................................. 34 5.1.1. Block Diagram .................................................................. 34 5.1.2. Data Operation Modes...................................................... 34 5.2. Control Block Description..................................................... 35 5.2.1. SPI Interface..................................................................... 35 5.2.2. FIFO ................................................................................. 38 5.2.3. Sync Word Recognition .................................................... 40 5.2.4. Packet Handler ................................................................. 40 5.2.5. Control.............................................................................. 40 5.3. Continuous Mode ................................................................ 41 Rev 7 - Sept 2nd, 2008 5.3.1. General Description .......................................................... 41 5.3.2. Tx Processing ................................................................... 41 5.3.3. Rx Processing................................................................... 42 5.3.4. Interrupt Signals Mapping ................................................. 42 5.3.5. uC Connections ................................................................ 43 5.3.6. Continuous Mode Example ............................................... 43 5.4. Buffered Mode ..................................................................... 44 5.4.1. General Description .......................................................... 44 5.4.2. Tx Processing ................................................................... 44 5.4.3. Rx Processing................................................................... 45 5.4.4. Interrupt Signals Mapping ................................................. 46 5.4.5. uC Connections ................................................................ 47 5.4.6. Buffered Mode Example.................................................... 47 5.5. Packet Mode........................................................................ 49 5.5.1. General Description .......................................................... 49 5.5.2. Packet Format .................................................................. 49 5.5.3. Tx Processing ................................................................... 51 5.5.4. Rx Processing................................................................... 51 5.5.5. Packet Filtering ................................................................. 52 5.5.6. DC-Free Data Mechanisms............................................... 53 5.5.7. Interrupt Signal Mapping ................................................... 54 5.5.8. uC Connections ................................................................ 55 5.5.9. Packet Mode Example ...................................................... 56 5.5.10. Additional Information ..................................................... 56 6. Configuration and Status Registers......................................... 58 6.1. General Description ............................................................. 58 6.2. Main Configuration Register - MCParam.............................. 58 6.3. Interrupt Configuration Parameters - IRQParam .................. 60 6.4. Receiver Configuration parameters - RXParam ................... 62 6.5. Sync Word Parameters - SYNCParam................................. 63 6.6. Transmitter Parameters - TXParam ..................................... 64 6.7. Oscillator Parameters - OSCParam ..................................... 64 6.8. Packet Handling Parameters - PKTParam .......................... 65 7. Application Information ........................................................... 66 7.1. Crystal Resonator Specification ........................................... 66 7.2. Software for Frequency Calculation ..................................... 66 7.2.1. GUI ................................................................................... 66 7.2.2. .dll for Automatic Production Bench .................................. 66 7.3. Switching Times and Procedures......................................... 66 7.3.1. Optimized Receive Cycle .................................................. 67 7.3.2. Optimized Transmit Cycle ................................................. 68 7.3.3. Transmitter Frequency Hop Optimized Cycle .................... 69 7.3.4. Receiver Frequency Hop Optimized Cycle........................ 70 7.3.5. Rx Tx and Tx Rx Jump Cycles ..................................... 71 7.4. Reset of the Chip ................................................................. 72 7.4.1. POR.................................................................................. 72 7.4.2. Manual Reset.................................................................... 72 7.5. Reference Design ................................................................ 73 7.5.1. Application Schematic....................................................... 73 7.5.2. PCB Layout ...................................................................... 73 7.5.3. Bill Of Material .................................................................. 74 7.5.4. SAW Filter Plot ................................................................. 75 7.5.5. Ordering Information for Tools .......................................... 75 7.6. Reference Design Performance ........................................... 76 7.6.1. Sensitivity Flatness ........................................................... 77 7.6.2. Sensitivity vs. LO Drift....................................................... 78 7.6.3. Sensitivity vs. Receiver BW .............................................. 79 7.6.4. Sensitivity Stability over Temperature and Voltage............ 80 7.6.5. Sensitivity vs. Bit Rate ...................................................... 80 7.6.6. Adjacent Channel Rejection.............................................. 81 7.6.7. Output Power Flatness...................................................... 82 7.6.8. Pout and IDD vs. PA Setting ............................................. 83 Page 2 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.9. Pout Stability over Temperature and Voltage .................... 84 7.6.10. Transmitter Spectral Purity ............................................. 85 7.6.11. OOK Channel Bandwidth................................................ 86 7.6.12. FSK Spectrum in Europe ................................................ 87 7.6.13. Digital Modulation Schemes............................................ 88 7.6.14. Current Stability over Temperature and Voltage ............. 89 8. Packaging Information ............................................................ 90 8.1. Package Outline Drawing..................................................... 90 8.2. PCB Land Pattern................................................................ 90 8.3. Tape & Reel Specification.................................................... 91 9. Revision History...................................................................... 92 10. Contact Information .............................................................. 92 Index of Figures Figure 1: SX1211 Simplified Block Diagram ................................. 5 Figure 2: SX1211 Pin Diagram ..................................................... 6 Figure 3: SX1211 Detailed Block Diagram.................................. 12 Figure 4: Power Supply Breakdown............................................ 13 Figure 5: Frequency Synthesizer Description.............................. 14 Figure 6: LO Generator .............................................................. 14 Figure 7: Loop Filter ................................................................... 16 Figure 8: Transmitter Architecture .............................................. 18 Figure 9: I(t), Q(t) Overview ........................................................ 18 Figure 10: PA Control ................................................................. 21 Figure 11: Optimal Load Impedance Chart ................................. 21 Figure 12: Recommended PA Biasing and Output Matching ..... 22 Figure 13: Front-end Description ................................................ 22 Figure 14: Receiver Architecture ................................................ 23 Figure 15: FSK Receiver Setting ................................................ 23 Figure 16: OOK Receiver Setting ............................................... 23 Figure 17: Active Channel Filter Description ............................... 24 Figure 18: Butterworth Filter's Actual BW ................................... 26 Figure 19: Polyphase Filter's Actual BW ..................................... 26 Figure 20: RSSI Dynamic Range................................................ 27 Figure 21: RSSI IRQ Timings ..................................................... 28 Figure 22: OOK Demodulator Description................................... 29 Figure 23: Floor Threshold Optimization ..................................... 30 Figure 24: BitSync Description.................................................... 31 Figure 25: SX1211's Data Processing Conceptual View............. 34 Figure 26: SPI Interface Overview and uC Connections ............. 35 Figure 27: Write Register Sequence ........................................... 36 Figure 28: Read Register Sequence........................................... 37 Figure 29: Write Bytes Sequence (ex: 2 bytes) ........................... 37 Figure 30: Read Bytes Sequence (ex: 2 bytes)........................... 38 Figure 31: FIFO and Shift Register (SR) ..................................... 38 Figure 32: FIFO Threshold IRQ Source Behavior ....................... 39 Figure 33: Sync Word Recognition ............................................. 40 Figure 34: Continuous Mode Conceptual View ........................... 41 Figure 35: Tx Processing in Continuous Mode............................ 41 Figure 36: Rx Processing in Continuous Mode ........................... 42 Figure 37: uC Connections in Continuous Mode......................... 43 Figure 38: Buffered Mode Conceptual View................................ 44 Figure 39: Tx processing in Buffered Mode ................................ 45 Figure 40: Rx Processing in Buffered Mode................................ 46 Figure 41: uC Connections in Buffered Mode ............................. 47 Figure 42: Packet Mode Conceptual View .................................. 49 Figure 43: Fixed Length Packet Format...................................... 50 Figure 44: Variable Length Packet Format.................................. 51 Figure 45: CRC Implementation ................................................. 53 Figure 46: Manchester Encoding/Decoding ................................ 54 Figure 47: Data Whitening .......................................................... 54 Figure 48: uC Connections in Packet Mode ................................ 55 Figure 49: Optimized Rx Cycle ................................................... 67 Figure 50: Optimized Tx Cycle.................................................... 68 Figure 51: Tx Hop Cycle ............................................................. 69 Figure 52: Rx Hop Cycle............................................................. 70 Tx Rx Cycle ................................................. 71 Figure 53: Rx Figure 54: POR Timing Diagram................................................. 72 Figure 55: Manual Reset Timing Diagram................................... 72 Figure 56: Reference Design Circuit Schematic.......................... 73 Figure 57: Reference Design`s Stackup...................................... 74 Figure 58: Reference Design Layout (top view) .......................... 74 Figure 59: 915 MHz SAW Filter Plot ........................................... 75 Figure 60: 869 MHz SAW Filter Plot ........................................... 75 Figure 61: Sensitivity Across the 868 MHz Band......................... 77 Figure 62: Sensitivity Across the 915 MHz Band......................... 77 Figure 63: FSK Sensitivity Loss vs. LO Drift................................ 78 Figure 64: OOK Sensitivity Loss vs. LO Drift............................... 78 Figure 65: FSK Sensitivity vs. Rx BW ......................................... 79 Figure 66: OOK Sensitivity Change vs. Rx BW ........................... 79 Figure 67: Sensitivity Stability ..................................................... 80 Figure 68: FSK Sensitivity vs. BR ............................................... 80 Figure 69: OOK Sensitivity vs. BR .............................................. 81 Figure 70: ACR in FSK Mode...................................................... 81 Figure 71: ACR in OOK Mode..................................................... 82 Figure 72: Pout for 869 MHz Band Operation ............................. 82 Figure 73: Pout for 915 MHz Band Operation ............................. 83 Figure 74: Pout and IDD at all PA Settings, 869 MHz ................. 83 Figure 75: Pout and IDD at all PA Settings, 915 MHz ................. 84 Figure 76: Pout Stability.............................................................. 84 Figure 77: 869 MHz Spectral Purity DC-1GHz ............................ 85 Figure 78: 869 MHz Spectral Purity 1-6GHz ............................... 85 Figure 79: OOK Spectrum - 2kbps.............................................. 86 Figure 80: OOK Spectrum - 8kbps.............................................. 86 Figure 81: OOK Spectrum - 16.7kbps ......................................... 86 Figure 82: FSK - 1.56kbps - +/-33 kHz........................................ 87 Figure 83: FSK - 25 kbps - +/-50 kHz.......................................... 87 Figure 84: FSK - 40 kbps - +/-40 kHz.......................................... 87 Figure 85: DTS 6dB Bandwidth................................................... 88 Figure 86: DTS Power Spectral Density...................................... 88 Figure 87: IDD vs. Temp and VDD.............................................. 89 Figure 88: Package Outline Drawing........................................... 90 Figure 89: PCB Land Pattern...................................................... 90 Figure 90: Tape & Reel Dimensions ........................................... 91 Rev 7 - Sept 2nd, 2008 Page 3 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Index of Tables Table 1: Ordering Information....................................................... 1 Table 2: SX1211 Pinouts.............................................................. 7 Table 3: Absolute Maximum Ratings ............................................ 8 Table 4: Operating Range ............................................................ 8 Table 5: Power Consumption Specification................................... 8 Table 6: Frequency Synthesizer Specification .............................. 9 Table 7: Transmitter Specification ................................................ 9 Table 8: Receiver Specification .................................................. 10 Table 9: Digital Specification ...................................................... 11 Table 10: MCParam_Freq_band Setting..................................... 15 Table 11: PA Rise/Fall Times ..................................................... 20 Table 12: Operating Modes ........................................................ 33 Table 13: Pin Configuration vs. Chip Mode................................. 33 Table 14: Data Operation Mode Selection .................................. 35 Table 15: Config vs. Data SPI Interface Selection ...................... 36 Table 16: Status of FIFO when Switching Between Different Modes of the Chip ...................................................................... 39 Table 17: Interrupt Mapping in Continuous Rx Mode .................. 42 Table 18: Interrupt Mapping in Continuous Tx Mode................... 42 Table 19: Relevant Config. Registers in Continuous Mode ........ 43 Table 20: Interrupt Mapping in Buffered Rx and Stby Modes ...... 46 Table 21: Interrupt Mapping in Buffered Tx Mode ....................... 46 Table 22: Relevant Configuration Registers in Buffered Mode .... 47 Table 23: Interrupt Mapping in Rx and Stby in Packet Mode ....... 55 Table 24: Interrupt Mapping in Tx Packet Mode.......................... 55 Table 25: Relevant Configuration Registers in Packet Mode....... 56 Table 26: Registers List .............................................................. 58 Table 27: MCParam Register Description ................................... 58 Table 28: IRQParam Register Description .................................. 60 Table 29: RXParam Register Description.................................... 62 Table 30: SYNCParam Register Description............................... 63 Table 31: TXParam Register Description .................................... 64 Table 32: OSCParam Register Description................................. 64 Table 33: PKTParam Register Description.................................. 65 Table 34: Crystal Resonator Specification .................................. 66 Table 35: Reference Design BOM .............................................. 74 Table 36: Tools Ordering Information.......................................... 75 Table 37: FSK Rx Filters vs. Bit Rate.......................................... 76 Table 38: OOK Rx Filters vs. Bit Rate......................................... 76 Acronyms BOM BR BW CCITT CP CRC DAC DDS DLL ERP ETSI FCC Fdev FIFO FS FSK GUI IC ID IF IRQ ITU LFSR LNA Bill Of Materials Bit Rate Bandwidth Comite Consultatif International Telephonique et Telegraphique - ITU Charge Pump Cyclic Redundancy Check Digital to Analog Converter Direct Digital Synthesis Dynamically Linked Library Equivalent Radiated Power European Telecommunications Standards Institute Federal Communications Commission Frequency Deviation First In First Out Frequency Synthesizer Frequency Shift Keying Graphical User Interface Integrated Circuit IDentificator Intermediate Frequency Interrupt ReQuest International Telecommunication Union Linear Feedback Shift Register Low Noise Amplifier LO LSB MSB NRZ NZIF OOK PA PCB PFD PLL POR RBW RF RSSI Rx SAW SPI SR Stby Tx uC VCO XO XOR Local Oscillator Least Significant Bit Most Significant Bit Non Return to Zero Near Zero Intermediate Frequency On Off Keying Power Amplifier Printed Circuit Board Phase Frequency Detector Phase-Locked Loop Power On Reset Resolution BandWidth Radio Frequency Received Signal Strength Indicator Receiver Surface Acoustic Wave Serial Peripheral Interface Shift Register Standby Transmitter Microcontroller Voltage Controlled Oscillator Crystal Oscillator eXclusive OR Rev 7 - Sept 2nd, 2008 Page 4 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING This product datasheet contains a detailed description of the SX1211 performance and functionality. Please consult the Semtech website for the latest updates or errata. 1. General Description The SX1211 is a single chip FSK and OOK transceiver capable of operation in the 863-870 MHz and 902-928 MHz license free ISM frequency bands, as well as the 950 - 960 MHz frequency band. It complies with both the relevant European and North American standards, EN 300-220 V2.1.1 (June 2006 release) and FCC Part 15 (10-1-2006 edition). A unique feature of this circuit is its extremely low current consumption in receiver mode of only 3mA (typ). The SX1211 comes in a 5x5 mm TQFN-32 package. 1.1. Simplified Block Diagram Figure 1: SX1211 Simplified Block Diagram Rev 7 - Sept 2nd, 2008 Page 5 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 1.2. Pin Diagram The following diagram shows the pins arrangement of the QFN package, top view. Figure 2: SX1211 Pin Diagram Notes: yyww refers to the date code ------ refers to the lot number Rev 7 - Sept 2nd, 2008 Page 6 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 1.3. Pin Description Table 2: SX1211 Pinouts Number 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Name GND TEST5 TEST1 VR_VCO VCO_M VCO_P LF_M LF_P TEST6 TEST7 XTAL_P XTAL_M TEST0 TEST8 NSS_CONFIG NSS_DATA MISO MOSI SCK CLKOUT DATA IRQ_0 IRQ_1 PLL_LOCK TEST2 TEST3 VDD VR_1V VR_DIG VR_PA TEST4 RFIO NC Type I I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I I/O I I O I I O I/O O O O I/O I/O I O O O I/O I/O Description Exposed ground pad Connect to GND Connect to GND Regulated supply of the VCO VCO tank VCO tank PLL loop filter PLL loop filter Connect to GND Connect to GND Crystal connection Crystal connection Connect to GND POR. Do not connect if unused SPI CONFIG enable SPI DATA enable SPI data output SPI data input SPI clock input Clock output NRZ data input and output (Continuous mode) Interrupt output Interrupt output PLL lock detection output Connect to GND Connect to GND Supply voltage Regulated supply of the analog circuitry Regulated supply of digital circuitry Regulated supply of the PA Connect to GND RF input/output Connect to GND Note: pin 13 (Test 8) can be used as an manual reset trigger. See section 7.4.2 for details on its use. Rev 7 - Sept 2nd, 2008 Page 7 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 2. Electrical Characteristics 2.1. ESD Notice The SX1211 is a high performance radio frequency device. It satisfies: Class 2 of the JEDEC standard JESD22-A114-B (Human Body Model), except on pins 3-4-5-27-28-29-31 where it satisfies Class 1A. Class III of the JEDEC standard JESD22-C101C (Charged Device Model) on all pins. It should thus be handled with all the necessary ESD precautions to avoid any permanent damage. 2.2. Absolute Maximum Ratings Stresses above the values listed below may cause permanent device failure. Exposure to absolute maximum ratings for extended periods may affect device reliability. Table 3: Absolute Maximum Ratings Symbol VDDmr Tmr Pmr Description Supply voltage Storage temperature Input level Min -0.3 -55 Max 3.7 125 0 Unit V C dBm 2.3. Operating Range Table 4: Operating Range Symbol VDDop Trop ML Description Supply Voltage Temperature Input Level Min 2.1 -40 Max 3.6 +85 0 Unit V C dBm 2.4. Chip Specification Conditions: Temp = 25 VDD = 3.3 V, crystal freq uency = 12.8 MHz, carrier frequency = 869 or 915 MHz, C, modulation FSK, data rate = 25 kb/s, Fdev = 50 kHz, fc = 100 kHz, unless otherwise specified. 2.4.1. Power Consumption Table 5: Power Consumption Specification Symbol IDDSL IDDST IDDFS IDDR IDDT (1) (2) Description Supply current, Sleep mode Supply current in standby mode, CLKOUT disabled Supply current in FS mode Supply current in Rx mode Supply current in Tx mode Conditions Crystal oscillator running Frequency synthesizer running Output power = +10 dBm (1) Output power = 1dBm (2) Min - Typ 0.1 65 1.3 3.0 25 16 Max 2 80 1.7 3.5 30 21 Unit A A mA mA mA mA Guaranteed by design and characterization Crystal Cload=10pF, C0=2.5pF, Rm=15 Ohms Rev 7 - Sept 2nd, 2008 Page 8 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 2.4.2. Frequency Synthesis Table 6: Frequency Synthesizer Specification Symbol FR BR_F BR_O FDA XTAL FSTEP TS_OSC TS_FS Description Frequency ranges Bit rate (FSK) Bit rate (OOK) Frequency deviation (FSK) Crystal oscillator frequency Frequency synthesizer step Oscillator wake-up time Frequency synthesizer wake-up time at most 10 kHz away from the target Conditions Programmable but requires specific BOM NRZ NRZ Min 863 902 950 1.56 1.56 33 9 Typ 50 12.8 2 1.5 500 180 200 250 260 290 320 340 Max 870 928 960 200 32 200 15 5 800 Unit MHz MHz MHz Kb/s Kb/s kHz MHz kHz ms s s s s s s s s Variable, depending on the frequency. (1) From Sleep mode From Stby mode 200 kHz step 1 MHz step TS_HOP Frequency synthesizer hop time at most 10 kHz away from the target 5 MHz step 7 MHz step 12 MHz step 20 MHz step 27 MHz step (1) Guaranteed by design and characterization 2.4.3. Transmitter Table 7: Transmitter Specification Symbol RFOP Description RF output power, programmable with 8 steps of typ. 3dB Phase noise Conditions Maximum power setting Minimum power setting Measured with a 600 kHz offset, at the transmitter output. At any offset between 200 kHz and 600 kHz, unmodulated carrier, Fdev = 50 kHz. From FS to Tx ready. From Stby to Tx ready. Min Typ +12.5 -8.5 -112 Max Unit dBm dBm dBc/Hz PN SPT (1) (1) Transmitted spurious - - -47 dBc TS_TR (1) Transmitter wake-up time Transmitter wake-up time - 120 600 500 900 s s TS_TR2 Guaranteed by design and characterization Rev 7 - Sept 2nd, 2008 Page 9 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 2.4.4. Receiver On the following table, fc and fo describe the bandwidth of the active channel filters as described in section 3.4.4.2. All sensitivities are measured receiving a PN15 sequence, for a BER of 0.1.% Table 8: Receiver Specification Symbol Description Conditions 869 MHz, BR=25 kb/s, Fdev =50 kHz, fc=100 kHz 869 MHz, BR=66.7 kb/s, Fdev=100 kHz, fc=200 kHz 915 MHz, BR=25 kb/s, Fdev=50 kHz, fc=100 kHz 915 MHz, BR = 66.7 kb/s, Fdev=100 kHz, fc=200 kHz 869 MHz, 2kb/s NRZ fc-fo=50 kHz, fo=50 kHz 869 MHz, 16.7 kb/s NRZ fc-fo=100 kHz, fo=100 kHz 915 MHz, 2kb/s NRZ fc-fo=50 kHz, fo=50 kHz 915 MHz, 16.7 kb/s NRZ fc-fo=100 kHz, fo=100 kHz Modulation as wanted signal Offset = 300 kHz, unwanted tone is not modulated Offset = 600 kHz, unwanted tone is not modulated Offset = 1.2 MHz, unwanted tone is not modulated Offset = 1 MHz, unmodulated Offset = 2 MHz, unmodulated, no SAW Offset = 10 MHz, unmodulated, no SAW Single side BW Polyphase Off Single side BW Polyphase On Interferers at 1MHz and 1.950 MHz offset From FS to Rx ready From Stby to Rx ready 200 kHz step 1MHz step 5MHz step 7MHz step 12MHz step 20MHz step 27MHz step From Rx ready Ranging from sensitivity Min 50 50 Typ -107 -103 -105 -101 -113 -106 -111 -105 -12 27 52 57 -48 -37 -33 -28 280 600 400 400 460 480 520 550 600 70 Max 250 400 500 900 1/Fdev Unit dBm dBm dBm dBm dBm dBm dBm dBm dBc dB dB dB dBm dBm dBm kHz kHz dBm s s s s s s s s s s dB RFS_F Sensitivity (FSK) RFS_O Sensitivity (OOK) CCR Co-channel rejection ACR Adjacent channel rejection BI Blocking immunity RXBW_F (1,2) RXBW_O IIP3 (1,2) TS_RE (1) TS_RE2 (1) Receiver bandwidth in FSK mode Receiver bandwidth in OOK mode rd Input 3 order intercept point Receiver wake-up time Receiver wake-up time TS_RE_HOP Receiver hop time from Rx ready to Rx ready with a frequency hop TS_RSSI DR_RSSI (1) (2) RSSI sampling time RSSI dynamic Range Guaranteed by design and characterization This reflects the whole receiver bandwidth, as described in sections 3.4.4.1 and 3.4.4.2 Page 10 of 92 Rev 7 - Sept 2nd, 2008 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 2.4.5. Digital Specification Conditions: Temp = 25 VDD = 3.3 V, crystal freq uency = 12.8 MHz, unless otherwise specified. C, Table 9: Digital Specification Symbol VIH VIL VOH VOL SCK_CONFIG SCK_DATA T_DATA T_MOSI_C T_MOSI_D T_NSSC_L T_NSSD_L T_NSSC_H T_NSSD_H Description Digital input level high Digital input level low Digital output level high Digital output level low SPI Config. clock frequency SPI Data clock frequency DATA hold and setup time MOSI setup time for SPI Config. MOSI setup time for SPI Data. NSS_CONFIG low to SCK rising edge. SCK falling edge to NSS_CONFIG high. NSS_DATA low to SCK rising edge. SCK falling edge to NSS_DATA high. NSS_CONFIG rising to falling edge. NSS_DATA rising to falling edge. Conditions Min 0.8*VDD 0.9*VDD 2 250 312 500 625 500 625 Typ Max 0.2*VDD 0.1*VDD 6 1 Unit V V V V MHz MHz s ns ns ns ns ns ns Imax=1mA Imax=-1mA Note: on pin 10 (XTAL_P) and 11 (XTAL_N), maximum voltages of 1.8V can be applied. Rev 7 - Sept 2nd, 2008 Page 11 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3. Architecture Description This section describes in depth the architecture of this ultra low-power transceiver: VR_PA PA RFIO I LO1 Tx Q I Q LO2 Tx Waveform generator I Q LO2 Tx RSSI OOK demod BitSync LNA LO2 Rx LO1 Rx FSK demod Control IRQ_0 IRQ_1 MOSI MISO SCK NSS_CONFIG NSS_DATA CLKOUT DATA LO1 Rx XTAL_P XO XTAL_M Frequency Synthesizer LO Generator I LO1 Tx Q I LO2 Tx Q LF_M LF_P VCO_P VCO_M VR_VCO VR_1V VR_DIG I LO2 Rx Q TEST(8:0) PLL_LOCK Figure 3: SX1211 Detailed Block Diagram 3.1. Power Supply Strategy To provide stable sensitivity and linearity characteristics over a wide supply range, the SX1211 is internally regulated. This internal regulated power supply structure is described below: Rev 7 - Sept 2nd, 2008 Page 12 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Vbat 1F Y5V VDD - Pin 26 2.1 - 3.6V External Supply Reg_top 1.4 V Biasing : -SPI -Config. Registers -POR Reg_ana 1.0 V Biasing analog blocks Reg_dig 1.0 V Biasing digital blocks Reg_VCO 0.85 V Biasing : -VCO circuit -Ext. VCO tank Reg_PA 1.80 V Biasing : -PA Driver -PA choke (ext) VR_1V Pin 27 VR_DIG Pin 28 VR_VCO Pin 3 VR_PA Pin 29 1F Y5V 220nF X7R 100nF X7R 47nF X7R Figure 4: Power Supply Breakdown To ensure correct operation of the regulator circuit, the decoupling capacitor connection shown in Figure 4 is required. These decoupling components are recommended for any design. 3.2. Frequency Synthesis Description The frequency synthesizer of the SX1211 is a fully integrated integer-N type PLL. The PLL circuit requires only five external components for the PLL loop filter and the VCO tank circuit. 3.2.1. Reference Oscillator The SX1211 embeds a crystal oscillator, which provides the reference frequency for the PLL. The recommended crystal specification is given in section 7.1. 3.2.2. CLKOUT Output The reference frequency, or a sub-multiple of it, can be provided on CLKOUT (pin 19) by activating the bit OSCParam_Clkout_on. The division ratio is programmed through bits OSCParam_Clkout_freq. The two applications of the CLKOUT output are: To provide a clock output for a companion uC, thus saving the cost of an additional oscillator. CLKOUT can be made available in any operation mode, except Sleep mode, and is automatically enabled at power-up. To provide an oscillator reference output. Measurement of the CLKOUT signal enables simple software trimming of the initial crystal tolerance. Note: To minimize the current consumption of the SX1211, ensure that the CLKOUT signal is disabled when unused. Rev 7 - Sept 2nd, 2008 Page 13 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3.2.3. PLL Architecture The crystal oscillator (XO) forms the reference oscillator of an Integer-N Phase Locked Loop (PLL), whose operation is discussed in the following section. Figure 5 shows a block schematic of the SX1211 PLL. Here the crystal reference frequency and the software controlled dividers R, P and S determine the output frequency of the PLL. /75.(Pi+1)+Si LO PFD XO /(Ri+1) Fcomp XT_M XT_P LF_M Vtune LF_P VCO_M VR_VCO VCO_P Figure 5: Frequency Synthesizer Description The VCO tank inductors are connected on an external differential input. Similarly, the loop filter is also located externally. However, there is an internal 8pF capacitance at VCO input that should be subtracted from the desired loop filter capacitance. The output signal of the VCO is used as the input to the local oscillator (LO) generator stage, illustrated in Figure 6. The VCO frequency is subdivided and used in a series of up (down) conversions for transmission (reception). LO1 Rx I Receiver LOs LO2 Rx /8 90 LO VCO Output I Q LO1 Tx 90 Q I Transmitter LOs LO2 Tx /8 90 Q Figure 6: LO Generator 3.2.4. PLL Tradeoffs With an integer-N PLL architecture, the following criterion must be met to ensure correct operation: The comparison frequency, Fcomp, of the Phase Frequency Detector (PFD) input must remain higher than six times the PLL bandwidth (PLLBW) to guarantee loop stability and to reject harmonics of the comparison frequency Fcomp. This is expressed in the inequality: PLLBW Fcomp 6 However the PLLBW has to be sufficiently high to allow adequate PLL lock times Because the divider ration R determines Fcomp, it should be set close to 119, leading to Fcomp100 kHz which will ensure suitable PLL stability and speed. Rev 7 - Sept 2nd, 2008 Page 14 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING With the recommended Bill Of Materials (BOM) of the reference design of section 7.5.3, the PLL prototype is the following: 64 R 169 S < P+1 PLLBW = 15 kHz nominal Startup times and reference frequency spurs as specified. 3.2.5. Voltage Controlled Oscillator The integrated VCO requires only two external tank circuit inductors. As the input is differential, the two inductors should have the same nominal value. The performance of these components is important for both the phase noise and the power consumption of the PLL. It is recommended that a pair of high Q factor inductors is selected. These should be mounted orthogonally to other inductors (in particular the PA choke) to reduce spurious coupling between the PA and VCO. In addition, such measures may reduce radiated pulling effects and undesirable transient behavior, thus minimizing spectral occupancy. Note that ensuring a symmetrical layout of the VCO inductors will further improve PLL spectral purity. For best performance wound type inductors, with tight tolerance, should be used as described in section 7.5.3. 3.2.5.1. SW Settings of the VCO To guarantee the optimum operation of the VCO over the SX1211's frequency and temperature ranges, the following settings should be programmed into the SX1211: Target channel (MHz) Freq_band 863870 10 902915 00 915928 01 950960 10 Table 10: MCParam_Freq_band Setting 3.2.5.2. Trimming the VCO Tank by Hardware and Software To ensure that the frequency band of operation may be accurately addressed by the R, P and S dividers of the synthesizer, it is necessary to ensure that the VCO is correctly centered. Note that for the reference design (see section 7.5) no centering is necessary. However, any deviation from the reference design may require the optimization procedure, outlined below, to be implemented. This procedure is simplified thanks to the built-in VCO trimming feature which is controlled over the SPI interface. This tuning does not require any RF test equipment, and can be achieved by simply measuring Vtune, the voltage between pins 6 (LFM) and 7 (LFP). The VCO is centered if the voltage is within the range: 50 Vtune(mV ) 150 Note that this measurement should be conducted when in transmit mode at the center frequency of the desired band (for example ~867 MHz in the 863-870 MHz band), with the appropriate MCParam_Freq_band setting. If this inequality is not satisfied then adjust the MCParam_VCO_trim bits from 00 whilst monitoring Vtune. This allows the VCO voltage to be trimmed in + 60 mV increments. Should the desired voltage range be inaccessible, the voltage may be adjusted further by changing the tank circuit inductance value. Note that an increase in inductance will result in an increase Vtune. Rev 7 - Sept 2nd, 2008 Page 15 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Note for mass production: The VCO capacitance is piece to piece dependant. As such, the optimization proposed above should be verified on several prototypes, to ensure that the population is centered on 100 mV. 3.2.6. PLL Loop Filter To adequately reject spurious components arising from the comparison frequency Fcomp, an external 2 loop filter is employed. RL1 LF_M CL2 CL1 LF_P nd order Figure 7: Loop Filter Following the recommendations made in section 3.2.4, the loop filter proposed in the reference design's bill of material on section 7.5.3 should be used. The loop filter settings are frequency band independent and are hence relevant to all implementations of the SX1211. 3.2.7. PLL Lock Detection Indicator The SX1211 also features a PLL lock detect indicator. This is useful for optimizing power consumption, by adjusting the synthesizer wake up time (TS_FS), since the PLL startup time is lower than specified under nominal conditions. The lock status can be read on bit IRQParam_PLL_lock, and must be cleared by writing a "1" to this same register. In addition, the lock status can be reflected in pin 23 PLL_LOCK, by setting the bit IRQParam_Enable_lock_detect. 3.2.8. Frequency Calculation As shown in Figure 5 the PLL structure comprises three different dividers, R, P and S, which set the output frequency through the LO. A second set of dividers is also available to allow rapid switching between a pair of frequencies: R1/P1/S1 and R2/P2/S2. These six dividers are programmed by six bytes of the register MCParam from addresses 6 to 11. 3.2.8.1. FSK Mode The following formula gives the relationship between the local oscillator, and R, P and S values, when using FSK modulation. 9 Flo 8 9 Fxtal [75(P + 1) + S )] Frf , fsk = 8 R +1 Frf , fsk = 3.2.8.2. OOK Mode Due to the manner in which the baseband OOK symbols are generated, the signal is always offset by the FSK frequency deviation (Fdev - as programmed in MCParam_Freq_dev). Hence, the center of the transmitted OOK signal is: Rev 7 - Sept 2nd, 2008 Page 16 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 9 Flo - Fdev 8 9 Fxtal Frf , ook , tx = [75(P + 1) + S )] - Fdev 8 R +1 Frf , ook , tx = Consequently, in receive mode, due to the low intermediate frequency (Low-IF) architecture of the SX1211 the frequency should be configured so as to ensure the correct low-IF receiver baseband center frequency, IF2. 9 Flo - IF 2 8 9 Fxtal Frf , ook , rx = [75(P + 1) + S )] - IF 2 8 R +1 Frf , ook , rx = Note that from Section 3.4.4, it is recommended that IF2 be set to 100 kHz. Rev 7 - Sept 2nd, 2008 Page 17 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3.3. Transmitter Description The SX1211 is set to transmit mode when MCParam_Chip_mode = 100. Amplification Second up-conversion First up-conversion Interpolation filters DACs DDS Data I LO2 Tx Q I RFIO PA Q I LO2 Tx Q LO1 Tx Waveform generator Clock RF IF Baseband Figure 8: Transmitter Architecture 3.3.1. Architecture Description The baseband I and Q signals are digitally generated by a DDS whose digital to analog converters (DAC) followed by two anti-aliasing low-pass filters transform the digital signal into analog in-phase (I) and quadrature (Q) components whose frequency is the selected frequency deviation (Fdev). 1 Fdev I(t) Q(t) Figure 9: I(t), Q(t) Overview In FSK mode, the relative phase of I and Q is switched by the input data between -90 and +90 with co ntinuous phase. The modulation is therefore performed at this initial stage, since the information contained in the phase difference will be converted into a frequency shift when the I and Q signals are up-converted in the first mixer stage. This first up-conversion stage is duplicated to enhance image rejection. The FSK convention is such that: DATA =' '1' ' Frf + Fdev DATA =' '0' ' Frf - Fdev Rev 7 - Sept 2nd, 2008 Page 18 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING In OOK mode, the phase difference between the I and Q channels is kept constant (independent of the transmitted data). Thus, the first stage of up-conversion creates a fixed frequency signal at the low IF = Fdev (This explains why the transmitted OOK spectrum is offset by Fdev). OOK Modulation is accomplished by switching on and off the PA and PA regulator stages. By convention: DATA =' '1' ' PAon DATA =' '0' ' PAoff After the interpolation filters, a set of four mixers combines the I and Q signals and converts them into a pair of complex signals at the second intermediate frequency, equal to 1/8 of the LO frequency, or 1/9 of the RF frequency. These two new I and Q signals are then combined and up-converted to the final RF frequency by two quadrature mixers fed by the LO signal. The signal is pre-amplified, and then the transmitter output is driven by a final power amplifier stage. 3.3.2. Bit Rate Setting In Continuous transmit mode, setting the Bit Rate is useful to determine the frequency of DCLK. As explained in section 5.3.2, DCLK will trigger an interrupt on the uC each time a new bit has to be transmitted. BR = FXTAL 64 * [1 + val ( MCParam _ BR)] 3.3.3. Alternative Settings Bit rate, frequency deviation and TX interpolation filter settings are a function of the reference oscillator crystal frequency, FXTAL. Settings other than those programmable with a 12.8 MHz crystal can be obtained by selection of the correct reference oscillator frequency. Please contact your local Semtech representative for further details. 3.3.4. Fdev Setting in FSK Mode The frequency deviation, Fdev, of the FSK transmitter is programmed through bits MCParam_Freq_dev: Fdev = FXTAL 32 * [1 + val ( MCParam _ Freq _ dev)] For correct operation the modulation index should be such that: = 2* Fdev 2 BR It should be noted that for communications between a pair of SX1211s, that Fdev should be at least 33 kHz to ensure a correct operation on the receiver side. 3.3.5. Fdev Setting in OOK Mode Fdev has no physical meaning in OOK transmit mode. However, as has been shown - due to the DDS baseband signal generation, the OOK signal is always offset by "-Fdev" (see formulas is section 3.2.8). It is suggested that Fdev retains its default value of 100 kHz in OOK mode. Rev 7 - Sept 2nd, 2008 Page 19 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3.3.6. Interpolation Filter After digital to analog conversion, both I and Q signals are smoothed by interpolation filters. This block low-pass filters the digitally generated signal, and prevents the alias signals from entering the modulators. Its bandwidth can be programmed with the register RXParam_InterpFiltTx, and should be set to: BR BW 3 * Fdev + 2 Where Fdev is the programmed frequency deviation as set in MCParam_Freq_dev, and BR is the physical Bit Rate of transmission. Notes: Low interpolation filter bandwidth will attenuate the baseband I/Q signals thus reducing the power of the FSK signal. Conversely, excessive bandwidth will degrade spectral purity. For the wideband FSK modulation, for example when operating in DTS mode, the recommended filter setting can not be reached. However, the impact upon spectral purity will be negligible, due to the already wideband channel. 3.3.7. Power Amplifier The Power Amplifier (PA) integrated in the SX1211 operates under a regulated voltage supply of 1.8 V. The external PA choke inductor is biased by an internal regulator output made available on pin 29 (VR_PA). Thanks to these features, the PA output power is consistent over the power supply range. This is important for mobile applications where this allows both predictable RF performance and battery life. 3.3.7.1. Rise and Fall Times Control In OOK mode, the PA ramp times can be accurately controlled through the MCParam_PA_ramp register. Those bits directly control the slew rate of VR_PA output (pin 29). Table 11: PA Rise/Fall Times MCParam_PA_ramp 00 01 10 11 tVR_PA 3 us 8.5 us 15 us 23 us tPA_OUT (rise / fall) 2.5 / 2 us 5 / 3 us 10 / 6 us 20 / 10 us Rev 7 - Sept 2nd, 2008 Page 20 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING DATA VR_PA [V] 95 % 95 % tVR_PA tVR_PA PA Output power 60 dB 60 dB tPA_OUT tPA_OUT Figure 10: PA Control 3.3.7.2. Optimum Load Impedance As the PA and the LNA front-ends in the SX1211 share the same Input/Output pin, they are internally matched to approximately 50 . Pmax-1dB circle Max Power Zopt = 30+j25 Figure 11: Optimal Load Impedance Chart Please refer to the reference design section for an optimized PA load setting. Rev 7 - Sept 2nd, 2008 Page 21 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3.3.7.3. Suggested PA Biasing and Matching The recommended PA bias and matching circuit is illustrated below: VR_PA 47nF 100nH SAW PA RFIO DC block Antenna port Low-pass and DC block Figure 12: Recommended PA Biasing and Output Matching Please refer to section 7.5.3 of this document for the optimized matching arrangement for each frequency band. 3.3.8. Common Input and Output Front-End The receiver and the transmitter share the same RFIO pin (pin 31). Figure 13 below shows the configuration of the common RF front-end. In transmit mode, the PA and the PA regulator are active, with the voltage on the VR_PA pin equal to the nominal voltage of the regulator (1.8 V). The external inductance is used to bias the PA. In receive mode, both PA and PA regulator are off and VR_PA is tied to ground. The external inductance LT1 is then used to bias the LNA. VR_PA Reg_PA Rx_on PA To Antenna RFIO LNA Figure 13: Front-end Description Rev 7 - Sept 2nd, 2008 Page 22 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3.4. Receiver Description The SX1211 is set to receive mode when MCParam_Chip_mode = 011. First downconversion Second downconversion RSSI OOK demod Bit synchronizer LO2 Rx FSK demod Control logic -Pattern recognition -FIFO handler -SPI interface -Packet handler LNA LO1 Rx RF IF1 Baseband, IF2 in OOK Figure 14: Receiver Architecture 3.4.1. Architecture The SX1211 receiver employs a super-heterodyne architecture. Here, the first IF is 1/9 of the RF frequency (approximately 100MHz). The second down-conversion down-converts the I and Q signals to base band in the case of the FSK receiver (Zero IF) and to a low-IF (IF2) for the OOK receiver. Second down-conversion LO2 Rx First down-conversion th 0 IF2=0 in FSK mode IF1 100MHz Image frequency LO1 Rx Channel Frequencyl Figure 15: FSK Receiver Setting First down-conversion Second down-conversion 0 IF2<0 in FSK mode equal to fo IF1 100MHz LO2 Rx Image frequency LO1 Rx Channel Frequency Figure 16: OOK Receiver Setting After the second down-conversion stage, the received signal is channel-select filtered and amplified to a level adequate for demodulation. Both FSK and OOK demodulation are available. Finally, an optional Bit Synchronizer (BitSync) is provided, to be supply a synchronous clock and data stream to a companion uC in Continuous mode, Rev 7 - Sept 2nd, 2008 Page 23 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING or to fill the FIFO buffers with glitch-free data in Buffered mode. The operation of the receiver is now described in detail. Note: Image rejection is achieved by the SAW filter. 3.4.2. LNA and First Mixer In receive mode, the RFIO pin is connected to a fixed gain, common-gate, Low Noise Amplifier (LNA). The performance of this amplifier is such that the Noise Figure (NF) of the receiver can be estimated to be 7 dB. 3.4.3. IF Gain and Second I/Q Mixer Following the LNA and first down-conversion, there is an IF amplifier whose gain can be programmed from 13.5 dB to 0 dB in 4.5 dB steps, via the register MCParam_IF_gain. The default setting corresponds to 0 dB gain, but lower values can be used to increase the RSSI dynamic range. Refer to section 3.4.7 for additional information. 3.4.4. Channel Filters The second mixer stages are followed by the channel select filters. The channel select filters have a strong influence on the noise bandwidth and selectivity of the receiver and hence its sensitivity. Each filter comprises a passive and active section. 3.4.4.1. Passive Filter Each channel select filter features a passive second-order RC filter, with a bandwidth programmable through the bits RXParam_PassiveFilt. As the wider of the two filters, its effect on the sensitivity is negligible, but its bandwidth has to be setup instead to optimize blocking immunity. The value entered into this register sets the single side bandwidth of this filter. For optimum performance it should be set to 3 to 4 times the cutoff frequency of the active Butterworth (or polyphase) filter described in the next section. 3 * Fc ButterfFilt BW passive, filter 4 * Fc ButterFilt 3.4.4.2. Active Filter The 'fine' channel selection is performed by an active, third-order, Butterworth filter, which acts as a low-pass filter for the zero-IF configuration (FSK), or a complex polyphase filter for the Low-IF (OOK) configuration. The RXParam_PolypFilt_on bit enables/disables the polyphase filter. Low-pass filter for FSK ( RXParam_PolyFilt_on=''0'') -fC 0 fC frequency Polyphase filter for OOK ( RXParam_PolyFilt_on=''1'' ) Canceled side of the polyphase filter -fC -fo 0 frequency Figure 17: Active Channel Filter Description Rev 7 - Sept 2nd, 2008 Page 24 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING As can be seen from Figure 17, the required bandwidth of this filter varies between the two demodulation modes. FSK mode: The 99% energy bandwidth of an FSK modulated signal is approximated to be: BR BW99%, FSK = 2 * Fdev + 2 The bits RXParam_ButterFilt set fc, the cutoff frequency of the filter. As we are in a Zero-IF configuration, the FSK lobes are centered around the virtual "DC" frequency. The choice of fc should be such that the modulated signal falls in the filter bandwidth, anticipating the Local Oscillator frequency drift over the operating temperature and aging of the device: 2 * fc > BW99%,FSK + LOdrifts Please refer to the charts in section 3.4.5 for an accurate overview of the filter bandwidth vs. setting. OOK mode: The 99% energy bandwidth of an OOK modulated signal is approximated to be: BW99%,OOK = 2 = 2.BR Tbit The bits RXParam_PolypFilt_center set fo, the center frequency of the polyphase filter when activated. fo should always be chosen to be equal to the low Intermediate Frequency of the receiver (IF2). This is why, in the GUI described in section 7.2.1 of this document, the low IF frequency of the OOK receiver denoted IF2 has been replaced by fo. The following setting is recommended: fo = 100kHz RXParam _ PolypFilt ="0011" The value stored in RXParam_ButterFilt determines fc, the filter cut-off frequency. So the user should set fc according to: 2 * ( fc - fo ) > BW 99 %,OOK + LO drifts Again, fc as a function of RXParam_ButterFilt is given in the section 3.4.6. 3.4.5. Channel Filters Setting in FSK Mode Fc, the 3dB cutoff frequency of the Butterworth filter used in FSK reception, is programmed through the bit RXParam_ButterFilt. However, the whole receiver chain influences this cutoff frequency. Thus the channel select and resultant filter bandwidths are summarized in the following chart: Rev 7 - Sept 2nd, 2008 Page 25 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Butterworth Filter's BW, FSK 450 400 350 Fc (3dB Cutoff) [kHz] 300 250 200 150 100 50 0 0 2 4 6 8 10 12 14 16 Val (RXParam_ButterFilt) [d] Actual BW Theoretical BW Figure 18: Butterworth Filter's Actual BW Table 37 suggests filter settings in FSK mode, along with the corresponding passive filter bandwidth and the accepted tolerance on the crystal reference. 3.4.6. Channel Filters Setting in OOK Mode The center frequency, fo, is always set to 100kHz. The following chart shows the receiver bandwidth when changing RXParam_Butterfilt bits, whilst the polyphase filter is activated. Polyphase Filter's BW, OOK 450 400 350 Fc-Fo with Fo=100 kHz [kHz] 300 250 200 150 100 50 0 0 2 4 6 8 10 Val (RXParam_ButterFilt [d] RXParam_PolypFilt="0011" 12 14 16 Actual BW Theoretical BW Figure 19: Polyphase Filter's Actual BW Table 38 suggests a few filter settings in OOK mode, along with the corresponding passive filter bandwidth and the accepted tolerance on the crystal reference. 3.4.7. RSSI After filtering, the In-phase and Quadrature signals are amplified by a chain of 11 amplifiers, each with 6dB gain. The outputs of these amplifiers are used to evaluate the Received Signal Strength (RSSI). 3.4.7.1. Resolution and Accuracy Whilst the RSSI resolution is 0.5 dB, the absolute accuracy is not expected to be better than +/- 3dB due to process and external component variation. Higher accuracy whilst performing absolute RSSI measurements will require additional calibration. 3.4.7.2. Acquisition Time Rev 7 - Sept 2nd, 2008 Page 26 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING In OOK mode, the RSSI evaluates the signal strength by sampling I(t) and Q(t) signals 16 times in each period of the chosen IF2 frequency (refer to section 3.4.1). In FSK mode, the signals are sampled 16 times in each Fdev period, Fdev being the frequency deviation of the companion transmitter. An average is then performed over a sliding window of 16 samples. Hence, the RSSI output register RXParam_RSSI is updated 16 times in each Fdev or IF2 period. The following settings should be respected: FSK Mode: Ensure that the Fdev parameter (as described in MCParam_Fdev) remains consistent with the actual frequency deviation of the companion transmitter. OOK reception: Ensure that the Fdev parameter (as described in MCParam_Fdev) is equal with the frequency of I(t) and Q(t) signals, i.e. the second Intermediate Frequency, IF2, of the receiver (Note that this equals Fo, the center frequency of the polyphase filter). 3.4.7.3. Dynamic Range The dynamic range of the RSSI is over 70 dB, extending from the nominal sensitivity level. The IF gain setting available in MCParam_IF_gain is used to achieve this dynamic range: RSSI Response 180 160 140 120 RSSI_Val [0.5dB/bit] 100 80 60 40 20 0 -120 -100 -80 -60 Pin [dBm] -40 -20 0 IF_Gain=00 IF_Gain=01 IF_Gain=10 IF_Gain=11 Figure 20: RSSI Dynamic Range The RSSI response versus input signal is independent of the receiver filter bandwidth. However in the absence of any input signal, the minimum value directly reflects upon the noise floor of the receiver, which is dependant on the filter bandwidth of the receiver. 3.4.7.4. RSSI IRQ Source The SX1211 can also be used to detect a RSSI level above a pre-configured threshold. The threshold is set in IRQParam_RSSI_irq_thresh and the IRQ status stored in IRQParam_RSSI_irq (cleared by writing a "1"). An interrupt can be mapped to the IRQ0 IRQParam_Rx_stby_irq1. Figure 21 shows the IRQParam_RSSI_irq_thresh set to 28. Rev 7 - Sept 2nd, 2008 or IRQ1 pins timing diagram via bits IRQParam_Rx_stby_irq0 or of the RSSI interrupt source, with Page 27 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING RXParam_RSSI_val(7:0) IRQParam_RSSI_irq 24 26 27 30 25 20 20 20 18 22 33 20 22 34 33 Clear interrupt Figure 21: RSSI IRQ Timings 3.4.8. Fdev Setting in Receive Mode The effect of the Fdev setting is different between FSK and OOK modes: 3.4.8.1. FSK Rx Mode In FSK mode the Fdev setting, as configured by MCParam_Freq_Dev, sets sampling frequencies on the receiver. The user should make it consistent with the frequency deviation of the FSK signal that is received. 3.4.8.2. OOK Rx Mode The frequency deviation Fdev, as described above, sets the sampling rate of the RSSI block. It is therefore necessary to set Fdev to the recommended low-IF frequency, IF2, of 100 kHz: Fdev = IF 2 = 100 kHz MCParam _ Freq _ dev ="00000011" 3.4.9. FSK Demodulator The FSK demodulator provides data polarity information, based on the relative phase of the input I and Q signals at the baseband. Its outputs can be fed to the Bit Synchronizer to recover the timing information. The user can also use the raw, unsynchronized, output of the FSK demodulator in Continuous mode. The FSK demodulator of the SX1211 operates most effectively for FSK signals with a modulation index greater than or equal to two: = 3.4.10. OOK Demodulator 2 * Fdev 2 BR The OOK demodulator performs a comparison of the RSSI output and a threshold value. Three different threshold modes are available, programmed through the RXParam_OOK_thresh_type register. The recommended mode of operation is the "Peak" threshold mode, illustrated below in Figure 22: Rev 7 - Sept 2nd, 2008 Page 28 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING RSSI (dB) `'Peak -6dB'' Threshold `'Floor'' threshold defined by MCParam_OOK_floor_thresh Noise floor of receiver Time Zoom Decay in dB as defined in RXPAram_OOK_thresh_step Fixed 6dB difference Period as defined in RXParam_OOK_thresh_dec_period Figure 22: OOK Demodulator Description In peak threshold mode the comparison threshold level is the peak value of the RSSI, reduced by 6dB. In the absence of an input signal or during the reception of a logical "0", the acquired peak value is decremented by one RXPAram_OOK_thresh_step every RXParam_OOK_thresh_dec_period. When the RSSI output is null for a long time (for instance after a long string of "0" received, or if no transmitter is present), the peak threshold level will continue falling until it reaches the "Floor Threshold" that is programmed through the register MCParam_OOK_floor_thresh. The default settings of the OOK demodulator lead to the performance stated in the electrical specification. However, in applications in which sudden signal drops are awaited during a reception, the three parameters shall be optimized accordingly. 3.4.10.1. Optimizing the Floor Threshold MCParam_OOK_floor_thres determines the sensitivity of the OOK receiver, as it sets the comparison threshold for weak input signals (i.e. those close to the noise floor). Significant sensitivity improvements can be generated if configured correctly. Note that the noise floor of the receiver at the demodulator input depends on: The noise figure of the receiver. The gain of the receive chain from antenna to base band. The matching - including SAW filter. The bandwidth of the channel filters. It is therefore important to note that the setting of MCParam_OOK_floor_thresh will be application dependant. The following procedure is recommended to optimize MCParam_OOK_floor_thresh. Rev 7 - Sept 2nd, 2008 Page 29 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Set SX1211 in OOK Rx mode Adjust Bit Rate, Channel filter BW Default RXParam_OOK_thresh setting No input signal Continuous Mode Monitor DATA pin (pin 20) Increment MCParam_OOK_floor_thres Glitch activity on DATA ? Optimization complete Figure 23: Floor Threshold Optimization The new floor threshold value found during this test should be the value used for OOK reception with those receiver settings. Note that if the output signal on DATA is logic "1", the value of MCParam_OOK_floor_thres is below the noise floor of the receiver chain. Conversely, if the output signal on DATA is logic "1", the value of MAParam_floor_thres is several dB above the noise floor. 3.4.10.2. Optimizing OOK Demodulator Response for Fast Fading Signals A sudden drop in signal strength can cause the bit error rate to increase. For applications where the expected signal drop can be estimated the following OOK demodulator parameters RXParam_OOK_thresh_step and RXParam_OOK_thresh_dec_period can be optimized as described below for a given number of threshold decrements per bit RXParam_OOK_thresh_dec_period: 000 once in each chip period (d) 001 once in 2 chip periods 010 once in 4 chip periods 011 once in 8 chip periods 100 twice in each chip period 101 4 times in each chip period 110 8 times in each chip period 111 16 times in each chip period For each decrement of RXParam_OOK_thresh_step: 000 0.5 dB (d) 001 1.0 dB 010 1.5 dB 011 2.0 dB 100 3.0 dB 101 4.0 dB 110 5.0 dB 111 6.0 dB Rev 7 - Sept 2nd, 2008 Page 30 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 3.4.10.3. Alternative OOK Demodulator Threshold Modes In addition to the Peak OOK threshold mode, the user can alternatively select two other types of threshold detectors: Fixed threshold: The value is selected through the MCParam_OOK_floor_thresh register (refer to section 3.4.10.1 for further information concerning optimization of the floor threshold). Average threshold: Data supplied by the RSSI block is averaged with the following cutoff frequency: RXParam _ OOK _ cutoff = 00 Fcutoff = RXParam _ OOK _ cutoff = 11 Fcutoff = BR 8 * BR 32 * In the first example, the higher cut-off frequency enables a sequence of up to 8 consecutive "0" or "1" to be supported, whilst the lower cut-off frequency presented in the second example allows for the correct reception of up to 32 consecutive "0" or "1". 3.4.11. Bit Synchronizer The Bit Synchronizer (BitSync) is a block that provides a clean and synchronized digital output, free of glitches. Raw demodulator output (FSK or OOK) DATA BitSync Output To pin DATA and DCLK in continuous mode DCLK IRQ_1 Figure 24: BitSync Description The BitSync can be disabled through the bits RXParam_Bitsync_off, and by holding pin IRQ1 low. However, for optimum receiver performance, its use when running Continuous mode is strongly advised. With this option a DCLK signal is present on pin IRQ_1. The BitSync is automatically activated in Buffered and Packet modes. The bit synchronizer bit-rate is controlled by MCParam_BR. For a given bit rate, this parameter is determined by: BR = FXTAL 64 * [1 + MCParam _ BR ] Rev 7 - Sept 2nd, 2008 Page 31 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING For proper operation, the Bit Synchronizer must first receive three bytes of alternating logic value preamble, i.e. "0101" sequences. After this startup phase, the rising edge of DCLK signal is centered on the demodulated bit. Subsequent data transitions will preserve this centering. This has two implications: Firstly, if the Bit Rates of Transmitter and Receiver are known to be the same, the SX1211 will be able to receive an infinite unbalanced sequence (all "0s" or all "1s") with no restriction. If there is a difference in Bit Rate between Tx and Rx, the amount of adjacent bits at the same level that the BitSync can withstand can be estimated as: NumberOfBits = 1 BR * 2 BR This implies approximately 6 consecutive unbalanced bytes when the Bit Rate precision is 1%, which is easily achievable (crystal tolerance is in the range of 50 to 100 ppm). 3.4.12. Alternative Settings Bit Synchronizer and Active channel filter settings are a function of the reference oscillator crystal frequency, FXTAL. Settings other than those programmable with a 12.8 MHz crystal can be obtained by selection of the correct reference oscillator frequency. Please contact your local Semtech representative for further details. 3.4.13. Data Output After OOK or FSK demodulation, the baseband signal is made available to the user on pin 20, DATA, when Continuous mode is selected. In Buffered and Packet modes, the data is retrieved from the FIFO through the SPI interface. Rev 7 - Sept 2nd, 2008 Page 32 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 4. Operating Modes This section summarizes the settings for each operating mode of the SX1211, and explains the functionality available and the timing requirements for switching between modes. 4.1. Modes of Operation Table 12: Operating Modes Mode Sleep Standby FS Receive MCParam_Chip_mode 000 001 010 011 Active blocks SPI, POR SPI, POR, Top regulator, digital regulator, XO, CLKOUT (if activated through OSCParam_Clkout) Same + VCO regulator, all PLL and LO generation blocks Same as FS mode + LNA, first mixer, IF amplifier, second mixer set, channel filters, baseband amplifiers and limiters, RSSI, OOK or FSK demodulator, BitSync and all digital features if enabled Same as FS mode + DDS, Interpolation filters, all up-conversion mixers, PA driver, PA and external VR_PA pin output for PA choke. Transmit 100 4.2. Digital Pin Configuration vs. Chip Mode Table 13 describes the state of the digital IOs in each of the above described modes of operation, regardless of the data operating mode (Continuous, Buffered, or Packet). Table 13: Pin Configuration vs. Chip Mode Chip ..........Mode Pin NSS_CONFIG NSS_DATA MISO MOSI SCK IRQ_0 IRQ_1 DATA CLKOUT PLL_LOCK Input Input Input Input Input High-Z High-Z Input High-Z High-Z Input Input Input Input Input Output (1) Output (1) Input Output Output (2) Input Input Input Input Input Output (1) Output (1) Input Output Output (2) Input Input Input Input Input Output Output Output Output Output (2) Input Input Input Input Input Output Output Input Output Output (2) NSS_CONFIG has the priority over NSS_DATA Sleep mode Standby mode FS mode Receive mode Transmit mode Comment Output only if NSS_CONFIG or NSSDATA='0' Notes: (1): High-Z if Continuous mode is activated, else Output (2): Output if PLL_lock_en = 1, else High-Z (3): Valid logic states must be applied to inputs at all times to avoid unwanted leakage currents Rev 7 - Sept 2nd, 2008 Page 33 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5. Data Processing 5.1. Overview 5.1.1. Block Diagram Figure 25, illustrates the SX1211 data processing circuit. Its role is to interface the data to/from the modulator/demodulator and the uC access points (SPI, IRQ and DATA pins). It also controls all the configuration registers. The circuit contains several control blocks which are described in the following paragraphs. SX1211 Tx/Rx DATA CONTROL IRQ_0 IRQ_1 Data Rx SYNC RECOG. PACKET HANDLER FIFO (+SR) SPI CONFIG NSS_DATA SCK MOSI MISO Tx DATA Figure 25: SX1211's Data Processing Conceptual View The SX1211 implements several data operation modes, each with their own data path through the data processing section. Depending on the data operation mode selected, some control blocks are active whilst others remain disabled. 5.1.2. Data Operation Modes The SX1211 has three different data operation modes selectable by the user: Continuous mode: each bit transmitted or received is accessed in real time at the DATA pin. This mode may be used if adequate external signal processing is available. Buffered mode: each byte transmitted or received is stored in a FIFO and accessed via the SPI bus. uC processing overhead is hence significantly reduced compared to Continuous mode operation. The packet length is unlimited. Packet mode (recommended): user only provides/retrieves payload bytes to/from the FIFO. The packet is automatically built with preamble, Sync word, and optional CRC, DC free encoding and the reverse operation is performed in reception. The uC processing overhead is hence reduced further compared to Buffered mode. The maximum payload length is limited to the maximum FIFO limit of 64 bytes Rev 7 - Sept 2nd, 2008 Page 34 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Table 14: Data Operation Mode Selection MCParam_Data_mode 00 01 1x Data Operation Mode Continuous Buffered Packet Each of these data operation modes is described fully in the following sections. 5.2. Control Block Description 5.2.1. SPI Interface 5.2.1.1. Overview As illustrated in the Figure 26 below, the SX1211's SPI interface consists of two sub blocks: SPI Config: used in all data operation modes to read and write the configuration registers which control all the parameters of the chip (operating mode, bit rate, etc...) SPI Data: used in Buffered and Packet mode to write and read data bytes to and from the FIFO. (FIFO interrupts can be used to manage the FIFO content.) SX1211 Config. Registers SPI CONFIG (slave) NSS_CONFIG MOSI MISO SCK NSS_CONFIG MOSI MISO SCK NSS_DATA C FIFO SPI DATA (slave) (master) NSS_DATA Figure 26: SPI Interface Overview and uC Connections Both interfaces are configured in slave mode whilst the uC is configured as the master. They have separate selection pins (NSS_CONFIG and NSS_DATA) but share the remaining pins: SCK (SPI Clock): clock signal provided by the uC MOSI (Master Out Slave In): data input signal provided by the uC MISO (Master In Slave Out): data output signal provided by the SX1211 As described below, only one interface can be selected at a time with NSS_CONFIG having the priority: Rev 7 - Sept 2nd, 2008 Page 35 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Table 15: Config vs. Data SPI Interface Selection NSS_DATA 0 0 1 1 NSS_CONFIG 0 1 0 1 SPI Interface Config Data Config None The following paragraphs describe how to use each of these interfaces. 5.2.1.2. SPI Config Write Register To write a value into a configuration register the timing diagram below should be carefully followed by the uC. The register's new value is effective from the rising edge of NSS_CONFIG. 1 NSS_CONFIG (In) 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCK (In) New value at address A1 MOSI (In) start rw A(4) A(3) A(2) A(1) A(0) stop D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0) Address = A1 Current value at address A1* MISO (Out) HZ (input) x x x x x x x x D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0) HZ (input) * when writing the new value at address A1, the current content of A1 can be read by the uC. (In)/(Out) refers to SX1211 side Figure 27: Write Register Sequence Note that when writing more than one register successively, it is not compulsory to toggle NSS_CONFIG back high between two write sequences. The bytes are alternatively considered as address and value. In this instance, all new values will become effective on rising edge of NSS_CONFIG. Read Register To read the value of a configuration register the timing diagram below should be carefully followed by the uC. Rev 7 - Sept 2nd, 2008 Page 36 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 1 NSS_CONFIG (In) 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCK (In) MOSI (In) start rw A(4) A(3) A(2) A(1) A(0) stop Address = A1 x x x x x x x x Current value at address A1 MISO (Out) HZ (input) x x x x x x x x D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0) HZ (input) Figure 28: Read Register Sequence Note that when reading more than one register successively, it is not compulsory to toggle NSS_CONFIG back high between two read sequences. The bytes are alternatively considered as address and value. 5.2.1.3. SPI Data Write Byte (before/during Tx) To write bytes into the FIFO the timing diagram below should be carefully followed by the uC. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 NSS_DATA (In) SCK (In) 1st byte written 2nd byte written MOSI (In) D1(7) D1(6) D1(5) D1(4) D1(3) x D1(2) D1(1) D1(0) D2(7) D2(6) D2(5) D2(4) D2(3) D2(2) D2(1) D2(0) MISO (Out) HZ (input) x x x x x x x x HZ (input) x x x x x x x x x HZ (input) Figure 29: Write Bytes Sequence (ex: 2 bytes) Note that it is compulsory to toggle NSS_DATA back high between each byte written. The byte is pushed into the FIFO on the rising edge of NSS_DATA Rev 7 - Sept 2nd, 2008 Page 37 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Read Byte (after/during Rx) To read bytes from the FIFO the timing diagram below should be carefully followed by the uC. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 NSS_DATA (In) SCK (In) MOSI (In) x x x st x x x x x x x x x nd x x x x x 1 byte read 2 byte read MISO (Out) HZ (input) D1(7) D1(6) D1(5) D1(4) D1(3) D1(2) D1(1) D1(0) HZ (input) D2(7) D2(6) D2(5) D2(4) D2(3) D2(2) D2(1) D2(0) HZ (input) Figure 30: Read Bytes Sequence (ex: 2 bytes) Note that it is compulsory to toggle NSS_DATA back high between each byte read. 5.2.2. FIFO 5.2.2.1. Overview and Shift Register (SR) In Buffered and Packet modes of operation, both data to be transmitted and that has been received are stored in a configurable FIFO (First In First Out) device. It is accessed via the SPI Data interface and provides several interrupts for transfer management. The FIFO is 1 byte (8 bits) wide hence it only performs byte (parallel) operations, whereas the demodulator functions serially. A shift register is therefore employed to interface the two devices. In transmit mode it takes bytes from the FIFO and outputs them serially (MSB first) at the programmed bit rate to the modulator. Similarly, in Rx the shift register gets bit by bit data from the demodulator and writes them byte by byte to the FIFO. This is illustrated in figure below. byte1 byte0 Data Tx/Rx 1 MSB LSB FIFO 8 SR (8bits) Figure 31: FIFO and Shift Register (SR) 5.2.2.2. Size Selection The FIFO width is programmable, to 16, 32, 48 or 64 bytes via MCParam_Fifo_size Rev 7 - Sept 2nd, 2008 Page 38 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.2.2.3. Interrupt Sources and Flags All interrupt sources and flags are configured in the IRQParam section of the configuration register, with the exception of Fifo_threshold : /Fifoempty: /Fifoempty interrupt source is low when byte 0, i.e. whole FIFO, is empty. Otherwise it is high. Note that when retrieving data from the FIFO, /Fifoempty is updated on NSS_DATA falling edge, i.e. when /Fifoempty is updated to low state the currently started read operation must be completed. In other words, /Fifoempty state must be checked after each read operation for a decision on the next one (/Fifoempty = 1: more byte(s) to read; /Fifoempty = 0: no more byte to read). Write_byte: Write_byte interrupt source goes high for 1 bit period each time a new byte is transferred from the SR to the FIFO (i.e. each time a new byte is received) Fifofull: Fifofull interrupt source is high when the last FIFO byte, i.e. the whole FIFO, is full. Otherwise it is low. Fifo_overrun_clr: Fifo_overrun_clr flag is set when a new byte is written by the user (in Tx or Standby modes) or the SR (in Rx mode) while the FIFO is already full. Data is lost and the flag should be cleared by writing a 1, note that the FIFO will also be cleared. Tx_done: Tx_done interrupt source goes high when FIFO is empty and the SR's last bit has been send to the modulator (i.e. the last bit of the packet has been sent). One bit period delay is required after the rising edge of Tx_done to ensure correct RF transmission of the last bit. In practice this may not require special care in the uC software due to IRQ processing time. Fifo_threshold: Fifo_threshold interrupt source's behavior depends on the running mode (Tx, Rx or Stby mode) and the threshold itself can be programmed via MCParam_Fifo_thresh (B value). This behavior is illustrated in Figure 32. IRQ source 1 0 B B+1 B+2 # of bytes in FIFO Tx Rx & Stby Figure 32: FIFO Threshold IRQ Source Behavior 5.2.2.4. FIFO Clearing Table 16 below summarizes the status of the FIFO when switching between different modes Table 16: Status of FIFO when Switching Between Different Modes of the Chip From Stby Stby Rx Rx Tx Tx Any To Tx Rx Tx Stby Rx Stby Sleep FIFO Status Cleared Not cleared Cleared Cleared Not cleared Cleared Not cleared Cleared Comments In Buffered mode, FIFO cannot be written in Stby before Tx In Packet mode, FIFO can be written in Stby before Tx In Packet & Buffered modes FIFO can be read in Stby after Rx Rev 7 - Sept 2nd, 2008 Page 39 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.2.3. Sync Word Recognition 5.2.3.1. Overview Sync word recognition (also called Pattern recognition in previous products) is activated by setting RXParam_Sync_on. The bit synchronizer must also be activated. The block behaves like a shift register; it continuously compares the incoming data with its internally programmed Sync word and asserts the Sync IRQ source on each occasion that a match is detected. This is illustrated in Figure 33. Rx DATA Bit N-x = (NRZ) Sync_value[x] Bit N-1 = Bit N = Sync_value[1] Sync_value[0] DCLK SYNC Figure 33: Sync Word Recognition During the comparison of the demodulated data, the first bit received is compared with bit 7 (MSB) of byte at address 22 and the last bit received is compared with bit 0 (LSB) of the last byte whose address is determined by the length of the Sync word. When the programmed Sync word is detected the user can assume that this incoming packet is for the node and can be processed accordingly. 5.2.3.2. Configuration Size: Sync word size can be set to 8, 16, 24 or 32 bits via RXParam_Sync_size. In Packet mode this field is also used for Sync word generation in Tx mode. Error tolerance: The number of errors tolerated in the Sync word recognition can be set to 0, 1, 2 or 3 via RXParam_Sync_tol. Value: The Sync word value is configured in SYNCParam_Sync_value. In Packet mode this field is also used for Sync word generation in Tx mode. 5.2.4. Packet Handler The packet handler is the block used in Packet mode. Its functionality is fully described in section 5.5. 5.2.5. Control The control block configures and controls the full chip's behavior according to the settings programmed in the configuration registers. Rev 7 - Sept 2nd, 2008 Page 40 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.3. Continuous Mode 5.3.1. General Description As illustrated in Figure 34, in Continuous mode the NRZ data to (from) the (de)modulator is directly accessed by the uC on the bidirectional DATA pin (20). The SPI Data, FIFO and packet handler are thus inactive. Tx/Rx SX1211 DATA CONTROL IRQ_0 IRQ_1(DCLK) Data Rx SYNC RECOG. SPI NSS_CONFIG CONFIG SCK MOSI MISO Datapath Figure 34: Continuous Mode Conceptual View 5.3.2. Tx Processing In Tx mode, a synchronous data clock for an external uC is provided on IRQ_1 pin. Its timing with respect to the data is illustrated in Figure 35. DATA is internally sampled on the rising edge of DCLK so the uC can change logic state anytime outside the greyed out setup/hold zone. The use of DCLK is compulsory in FSK and optional in OOK. T_DATA T_DATA DATA (NRZ) DCLK Figure 35: Tx Processing in Continuous Mode Rev 7 - Sept 2nd, 2008 Page 41 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.3.3. Rx Processing If the bit synchronizer is disabled, the raw demodulator output is made directly available on DATA pin and no DCLK signal is provided. Conversely, if the bit synchronizer is enabled, synchronous cleaned data and clock are made available respectively on DATA and IRQ_1 pins. DATA is sampled on the rising edge of DCLK and updated on the falling edge as illustrated in Figure 36. DATA (NRZ) DCLK Figure 36: Rx Processing in Continuous Mode Note that in Continuous mode it is always recommended to enable the bit synchronizer to clean the DATA signal even if the DCLK signal is not used by the uC. (bit synchronizer is automatically enabled in Buffered and Packet mode). 5.3.4. Interrupt Signals Mapping The tables below give the description of the interrupts available in Continuous mode. Rx_stby_irq_0 00 (d) 01 1x IRQ_0 Rx Sync RSSI DCLK IRQ_1 Table 17: Interrupt Mapping in Continuous Rx Mode Note: In Continuous mode, no interrupt is available in Stby mode Tx DCLK IRQ_0 IRQ_1 Table 18: Interrupt Mapping in Continuous Tx Mode Rev 7 - Sept 2nd, 2008 Page 42 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.3.5. uC Connections SX1211 DATA IRQ_0 IRQ_1 (DCLK) NSS_CONFIG SCK MOSI MISO uC Figure 37: uC Connections in Continuous Mode Note that some connections may not be needed depending on the application: IRQ_0: if Sync and RSSI interrupts are not used. In this case, leave floating. IRQ_1: if the chip is never used in Tx FSK mode (DCLK connection is not compulsory in Rx and Tx OOK modes). In this case, leave floating. MISO: if no read register access is needed. In this case, pull-up to VDD through a 100 k resistor. In addition, NSS_DATA pin (unused in continuous mode) should be pulled-up to VDD through a 100 k Please refer to Table 13 for SX1211's pins configuration resistor. 5.3.6. Continuous Mode Example Configure all data processing related registers listed below appropriately. In this example we assume that both Bit synchronizer and Sync word recognition are on. Table 19: Relevant Configuration Registers in Continuous Mode (data processing related only) MCParam IRQParam RXParam SYNCParam Data_mode_x Rx_stby_irq_0 Sync_on Sync_size Sync_tol Sync_value Tx X Rx X X X X X X Description Defines data operation mode ( Continuous) Defines IRQ_0 source in Rx mode Enables Sync word recognition Defines Sync word size Defines the error tolerance on Sync word recognition Defines Sync word value Tx Mode: Go to Tx mode (and wait for Tx to be ready, see Figure 50) Send all packet's bits on DATA pin synchronously with DCLK signal provided on IRQ_1 Go to Sleep mode Rx Mode: Program Rx interrupts: IRQ_0 mapped to Sync (Rx_stby_irq_0="00") and IRQ_1 mapped to DCLK (Bit synchronizer enabled) Go to Rx mode (note that Rx is not ready immediately, see Figure 49) Wait for Sync interrupt Get all packet bits on DATA pin synchronously with DCLK signal provided on IRQ_1 Go to Sleep mode Rev 7 - Sept 2nd, 2008 Page 43 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.4. Buffered Mode 5.4.1. General Description As illustrated in Figure 38, for Buffered mode operation the NRZ data to (from) the (de)modulator is not directly accessed by the uC but stored in the FIFO and accessed via the SPI Data interface. This frees the uC for other tasks between processing data from the SX1211, furthermore it simplifies software development and reduces uC performance requirements (speed, reactivity). Note that in this mode the packet handler stays inactive. An important feature is also the ability to empty the FIFO in Stby mode, ensuring low power consumption and adding greater software flexibility. SX1211 CONTROL IRQ_0 IRQ_1 Data Rx SYNC RECOG. FIFO (+SR) SPI NSS_CONFIG CONFIG Tx DATA NSS_DATA SCK MOSI MISO Datapath Figure 38: Buffered Mode Conceptual View Note that Bit Synchronizer is automatically enabled in Buffered mode. The Sync word recognition must be enabled (RXParam_Sync_on=1) independently of the FIFO filling method selected (IRQParam_Fifo_fill_method). 5.4.2. Tx Processing After entering Tx in Buffered mode, the chip expects the uC to write into the FIFO, via the SPI Data interface, all the data bytes to be transmitted (preamble, Sync word, payload...). Actual transmission of first byte will start either when the FIFO is not empty (i.e. first byte written by the uC) or when the FIFO is full depending on bit IRQParam_Tx_start_irq_0. In Buffered mode the packet length is not limited, i.e. as long as there are bytes inside the FIFO they are sent. When the last byte is transferred to the SR, /Fifoempty IRQ source is asserted to warn the uC, at that time FIFO can still be filled with additional bytes if needed. When the last bit of the last byte has left the SR (i.e. 8 bit periods later), the Tx_done interrupt source is asserted and the user can exit Tx mode after waiting at least 1 bit period from the last bit processed by modulator. Rev 7 - Sept 2nd, 2008 Page 44 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING If the transmitter is switched off (for example due to entering another chip mode) during transmission it will stop immediately, even if there is still unsent data. Figure 39 illustrates Tx processing with a 16 byte FIFO depth and Tx_start_irq_0=0. Please note that in this example the packet length is equal to FIFO size, but this does not need to be the case, the uC can use the FIFO interrupts anytime during Tx to manage FIFO contents and write additional bytes. Start condition (Cf. Tx_start_irq_0) Fifofull /Fifoempty Tx_done from SPI Data 15 FIFO 0 b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 XXX b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 b10 b11 b12 b13 b14 b15 XXX Data Tx (from SR) Figure 39: Tx processing in Buffered Mode (FIFO size = 16, Tx_start_irq_0=0) 5.4.3. Rx Processing After entering Rx in Buffered mode, the chip requires the uC to retrieve the received data from the FIFO. The FIFO will actually start being filled with received bytes either; when a Sync word has been detected (in this case only the bytes following the Sync word are filled into the FIFO) or when the Fifo_fill bit is asserted by the user - depending on the state of bit, IRQParam_Fifo_fill_method. In Buffered mode, the packet length is not limited i.e. as long as Fifo_fill is set, the received bytes are shifted into the FIFO. The uC software must therefore manage the transfer of the FIFO contents by interrupt and ensure reception of the correct number of bytes. (In this mode, even if the remote transmitter has stopped, the demodulator will output random bits from noise) When the FIFO is full, Fifofull IRQ source is asserted to alert the uC, that at that time, the FIFO can still be unfilled without data loss. If the FIFO is not unfilled, once the SR is also full (i.e. 8 bits periods later) Fifo_overrun_clr is asserted and SR's content is lost. Figure 40 illustrates an Rx processing with a 16 bytes FIFO size and Fifo_fill_method=0. Please note that in the illustrative example of section 5.4.6, the uC does not retrieve any byte from the FIFO through SPI Data, causing overrun. Rev 7 - Sept 2nd, 2008 Page 45 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Data Rx (to SR) "noisy" data Start condition (Cf. Fifo_fill_method) /Fifoempty Fifofull Fifo_overrun_clr Write_byte 15 Preamble Sync b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 b10 b11 b12 b13 b14 b15 b16 FIFO b5 b6 b7 b9 b8 b10 b11 b12 b13 b14 b15 b4 b1 b2 b3 0 b0 Figure 40: Rx Processing in Buffered Mode (FIFO size=16, Fifo_fill_method=0) 5.4.4. Interrupt Signals Mapping The tables below describe the interrupts available in Buffered mode. Rx_stby_irq_x 00 (d) 01 10 11 00 (d) 01 10 11 IRQ_0 IRQ_1 Rx Write_byte /Fifoempty Sync Fifofull RSSI Fifo_threshold Stby /Fifoempty Fifofull Fifo_threshold Table 20: Interrupt Mapping in Buffered Rx and Stby Modes Tx IRQ_0 IRQ_1 Tx_irq_1=0 (d) Tx_irq_1=1 /Fifoempty Fifofull Tx_done Table 21: Interrupt Mapping in Buffered Tx Mode Rev 7 - Sept 2nd, 2008 Page 46 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.4.5. uC Connections SX1211 IRQ_0 IRQ_1 NSS_CONFIG NSS_DATA SCK MOSI MISO uC Figure 41: uC Connections in Buffered Mode Note that depending upon the application, some uC connections may not be needed: IRQ_0: if none of the relevant IRQ sources are used. In this case, leave floating. IRQ_1: if none of the relevant IRQ sources are used. In this case, leave floating. MISO: if no read register access is needed and the chip is used in Tx mode only. In this case, pull up to VDD through a 100 k resistor. In addition, DATA pin (unused in buffered mode) should be pulled-up to VDD through a 100 k Please refer to Table 13 for the SX1211's pin configuration. resistor. 5.4.6. Buffered Mode Example Configure all data processing related registers listed below appropriately. In this example we assume Sync word recognition is on and Fifo_fill_method=0. Tx X X X Rx X X X X X X X X X X X Description Defines data operation mode ( Buffered) Defines FIFO size Defines FIFO threshold Defines IRQ_0 source in Rx & Stby modes Defines IRQ_1 source in Rx & Stby modes Defines IRQ_1 source in Tx mode Defines FIFO filling method Controls FIFO filling status Defines Tx start condition and IRQ_0 source Defines Sync word size Defines the error tolerance on Sync word detection Defines Sync word value MCParam IRQParam RXParam SYNCParam Data_mode_x Fifo_size Fifo_thresh Rx_stby_irq_0 Rx_stby_irq_1 Tx_irq_1 Fifo_fill_method Fifo_fill Tx_start_irq_0 Sync_size Sync_tol Sync_value X Table 22: Relevant Configuration Registers in Buffered Mode (data processing related only) Tx Mode: Program Tx start condition and IRQs: Start Tx when FIFO is not empty (Tx_start_irq_0=1) and IRQ_1 mapped to Tx_done (Tx_irq_1=1) Go to Tx mode (and wait for Tx to be ready, see Figure 50) Rev 7 - Sept 2nd, 2008 Page 47 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Write packet bytes into FIFO. Tx starts when the first byte is written (Tx_start_irq_0=1). We assume the FIFO is being filled via SPI Data faster than being unfilled by SR. Wait for Tx_done interrupt (+1 bit period) Go to Sleep mode Rx Mode: Program Rx/Stby interrupts: IRQ_0 mapped to /Fifoempty (Rx_stby_irq_0=10) and IRQ_1 mapped to Fifo_threshold (Rx_stby_irq_1=11). Configure Fifo_thresh to an appropriate value (ex: to detect packet end if its length is known) Go to Rx mode (note that Rx is not ready immediately, Cf section 7.3.1). Wait for Fifo_threshold interrupt (i.e. Sync word has been detected and FIFO filled up to the defined threshold). If it is packet end, go to Stby (SR's content is lost). Read packet bytes from FIFO until /Fifoempty goes low (or correct number of bytes is read). Go to Sleep mode. Rev 7 - Sept 2nd, 2008 Page 48 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.5. Packet Mode 5.5.1. General Description Similar to Buffered mode operation, in Packet mode the NRZ data to (from) the (de)modulator is not directly accessed by the uC but stored in the FIFO and accessed via the SPI Data interface. In addition, the SX1211's packet handler performs several packet oriented tasks such as Preamble and Sync word generation, CRC calculation/check, whitening/dewhitening of data, address filtering, etc. This simplifies still further software and reduces uC overhead by performing these repetitive tasks within the RF chip itself. Another important feature is ability to fill and empty the FIFO in Stby mode, ensuring optimum power consumption and adding more flexibility for the software. SX1211 CONTROL IRQ_0 IRQ_1 Data Rx SYNC RECOG. PACKET HANDLER FIFO (+SR) SPI NSS_CONFIG CONFIG Tx DATA NSS_DATA SCK MOSI MISO Datapath Figure 42: Packet Mode Conceptual View Note that Bit Synchronizer and Sync word recognition are automatically enabled in Packet mode. 5.5.2. Packet Format Two types of packet formats are supported: fixed length and variable length, selectable by the PKTParam_Pkt_format bit. The maximum size of the payload is limited by the size of the FIFO selected (16, 32, 48 or 64 bytes). 5.5.2.1. Fixed Length Packet Format In applications where the packet length is fixed in advance, this mode of operation may be of interest to minimize RF overhead (no length byte field is required). All nodes, whether Tx only, Rx only, or Tx/Rx should be programmed with the same packet length value. The length of the payload is set by the PKTParam_Payload_length register and is limited by the size of the FIFO selected. Rev 7 - Sept 2nd, 2008 Page 49 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING The length stored in this register relates only to the payload which includes the message and the optional address byte. In this mode, the payload must contain at least one byte, i.e. address or message byte. An illustration of a fixed length packet is shown in Figure 43. It contains the following fields: Preamble (1010...). Sync word (Network ID). Optional Address byte (Node ID). Message data. Optional 2-bytes CRC checksum. Optional DC free data coding CRC checksum calculation Preamble 1 to 4 bytes Sync Word 1 to 4 bytes Address byte Message 0 to (FIFO size) bytes CRC 2-bytes Payload/FIFO Fields added by the packet handler in Tx and processed and removed in Rx Optional User provided fields which are part of the payload Message part of the payload Figure 43: Fixed Length Packet Format 5.5.2.2. Variable Length Packet Format This mode is necessary in applications where the length of the packet is not known in advance and can vary over time. It is then necessary for the transmitter to send the length information together with each packet in order for the receiver to operate properly. In this mode the length of the payload, indicated by the length byte in Figure 44, is given by the first byte of the FIFO and is limited only by the width of the FIFO selected. Note that the length byte itself is not included in its calculation. In this mode, the payload must contain at least 2 bytes, i.e. length + address or message byte. An illustration of a variable length packet is shown in Figure 44. It contains the following fields: Preamble (1010...). Sync word (Network ID). Length byte Optional Address byte (Node ID). Message data. Optional 2-bytes CRC checksum. Rev 7 - Sept 2nd, 2008 Page 50 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Optional DC free data coding CRC checksum calculation Length Preamble 1 to 4 bytes Sync Word 1 to 4 bytes Length byte Address byte Message 0 to (FIFO size - 1) bytes CRC 2-bytes Payload/FIFO Fields added by the packet handler in Tx and processed and removed in Rx Optional User provided fields which are part of the payload Message part of the payload Figure 44: Variable Length Packet Format 5.5.3. Tx Processing In Tx mode the packet handler dynamically builds the packet by performing the following operations on the payload available in the FIFO: Add a programmable number of preamble bytes Add a programmable Sync word Optionally calculating CRC over complete payload field (optional length byte + optional address byte + message) and appending the 2 bytes checksum. Optional DC-free encoding of the data (Manchester or whitening). Only the payload (including optional address and length fields) is to be provided by the user in the FIFO. Assuming that the chip is already in Tx mode then, depending on IRQParam_Tx_start_irq_0 bit, packet transmission (starting with programmed preamble) will start either after the first byte is written into the FIFO (Tx_start_irq_0=1) or after the number of bytes written reaches the user defined threshold (Tx_start_irq_0=0). The FIFO can also be fully or partially filled in Stby mode via PKTParam_Fifo_stby_access. In this case, the start condition will only be checked when entering Tx mode. At the end of the transmission (Tx_done = 1), the user must explicitly exit Tx mode if required. (e.g. back to Stby) Note that while in Tx mode, before and after actual packet transmission (not enough bytes or Tx_done), additional preamble bytes are automatically sent to the modulator. When the start condition is met, the current additional preamble byte is completely sent before the transmission of the next packet (i.e. programmed preamble) is started. 5.5.4. Rx Processing In Rx mode the packet handler extracts the user payload to the FIFO by performing the following operations: Receiving the preamble and stripping it off. Detecting the Sync word and stripping it off. Optional DC-free decoding of data. Optionally checking the address byte. Optionally checking CRC and reflecting the result on CRC_status bit and CRC_OK IRQ source. Only the payload (including optional address and length fields) is made available in the FIFO. Payload_ready and CRC_OK interrupts (the latter only if CRC is enabled) can be generated to indicate the end of the packet reception. Rev 7 - Sept 2nd, 2008 Page 51 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING By default, if the CRC check is enabled and fails for the current packet, then the FIFO is automatically cleared and neither of the two interrupts are generated and new packet reception is started. This autoclear function can be disabled via PKTParam_CRC_autoclr bit and, in this case, even if CRC fails, the FIFO is not cleared and only Payload_ready IRQ source is asserted. Once fully received, the payload can also be fully or partially retrieved in Stby mode via PKTParam_Fifo_stby_access. At the end of the reception, although the FIFO automatically stops being filled, it is still up to the user to explicitly exit Rx mode if required. (e.g. go to Stby to get payload). FIFO must be empty for a new packet reception to start. 5.5.5. Packet Filtering SX1211's packet handler offers several mechanisms for packet filtering ensuring that only useful packets are made available to the uC, reducing significantly system power consumption and software complexity. 5.5.5.1. Sync Word Based Sync word filtering/recognition is automatically enabled in Packet mode. It is used for identifying the start of the payload and also for network identification. As previously described, the Sync word recognition block is configured (size, error tolerance, value) via RXParam_Sync_size, RXParam_Sync_tol and SYNCParam configuration registers. This information is used, both for appending Sync word in Tx, and filtering packets in Rx. Every received packet which does not start with this locally configured Sync word is automatically discarded and no interrupt is generated. When the Sync word is detected, payload reception automatically starts and Sync IRQ source is asserted. 5.5.5.2. Address Based Address filtering can be enabled via the PKTParam_Adrs_filt bits. It adds another level of filtering, above Sync word, typically useful in a multi-node networks where a network ID is shared between all nodes (Sync word) and each node has its own ID (address). Three address based filtering options are available: Adrs_filt = 01: Received address field is compared with internal register Node_Adrs. If they match then the packet is accepted and processed, otherwise it is discarded. Adrs_filt = 10: Received address field is compared with internal register Node_Adrs and the constant 0x00. If either is a match, the received packet is accepted and processed, otherwise it is discarded. This additional check with a constant is useful for implementing broadcast in a multi-node networks. Adrs_filt = 11: Received address field is compared with internal register Node_Adrs and the constants 0x00 & 0xFF. If any of the three matches, then the received packet is accepted and processed, otherwise it is discarded. These additional checks with constants are useful for implementing broadcast commands of all nodes. Please note that the received address byte, as part of the payload, is not stripped off the packet and is made available in the FIFO. In addition, Node_Adrs and Adrs_filt only apply to Rx. On Tx side, if address filtering is expected, the address byte should simply be put into the FIFO like any other byte of the payload. 5.5.5.3. Length Based In variable length Packet mode, PKTParam_Payload_length must be programmed with the maximum length permitted. If received length byte is smaller than this maximum then the packet is accepted and processed, otherwise it is discarded. Rev 7 - Sept 2nd, 2008 Page 52 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Please note that the received length byte, as part of the payload, is not stripped off the packet and is made available in the FIFO. To disable this function the user should set the value of the PKTParam_Payload_length to the value of the FIFO size selected. 5.5.5.4. CRC Based The CRC check is enabled by setting bit PKTParam_CRC_on. It is used for checking the integrity of the message. On Tx side a two byte CRC checksum is calculated on the payload part of the packet and appended to the end of the message. On Rx side the checksum is calculated on the received payload and compared with the two checksum bytes received. The result of the comparison is stored in the PKTParam_CRC_status bit and CRC_OK IRQ source. By default, if the CRC check fails then the FIFO is automatically cleared and no interrupt is generated. This filtering function can be disabled via PKTParam_CRC_autoclr bit and in this case, even if CRC fails, the FIFO is not cleared and only Payload_ready interrupt goes high. Please note that in both cases, the two CRC checksum bytes are stripped off by the packet handler and only the payload is made available in the FIFO. The CRC is based on the CCITT polynomial as shown in Figure 45. This implementation also detects errors due to leading and trailing zeros. data input CRC Polynomial =X16 + X12 + X5 + 1 X15 X14 X13 X12 X11 *** X5 X4 *** X0 Figure 45: CRC Implementation 5.5.6. DC-Free Data Mechanisms The payload to be transmitted may contain long sequences of 1's and 0's, which introduces a DC bias in the transmitted signal. The radio signal thus produced has a non uniform power distribution over the occupied channel bandwidth. It also introduces data dependencies in the normal operation of the demodulator. Thus it is useful if the transmitted data is random and DC free. For such purposes, two techniques are made available in the packet handler: Manchester encoding and data whitening. Please note that only one of the two methods should be enabled at a time. 5.5.6.1. Manchester Encoding Manchester encoding/decoding is enabled by setting bit PKTParam_Manchester_on and can only be used in Packet mode. The NRZ data is converted to Manchester code by coding `1' as "10" and `0' as "01". In this case, the maximum chip rate is the maximum bit rate given in the specifications section and the actual bit rate is half the chip rate. Rev 7 - Sept 2nd, 2008 Page 53 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Manchester encoding and decoding is only applied to the payload and CRC checksum while preamble and Sync word are kept NRZ. However, the chip rate from preamble to CRC is the same and defined by MCParam_BR (Chip Rate = Bit Rate NRZ = 2 x Bit Rate Manchester). Manchester encoding/decoding is thus made transparent for the user, who still provides/retrieves NRZ data to/from the FIFO. 1/BR ...Sync 1/BR RF chips @ BR User/NRZ bits Manchester OFF User/NRZ bits Manchester ON ... ... ... 1 1 1 1 1 1 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 1 1 1 0 0 0 0 0 1 1 Payload... 0 1 1 0 0 1 1 1 0 0 1 1 1 0 0 ... ... ... t Figure 46: Manchester Encoding/Decoding 5.5.6.2. Data Whitening Another technique called whitening or scrambling is widely used for randomizing the user data before radio transmission. The data is whitened using a random sequence on the Tx side and de-whitened on the Rx side using the same sequence. Comparing to Manchester technique it has the advantage of keeping NRZ datarate i.e. actual bit rate is not halved. The whitening/de-whitening process is enabled by setting bit PKTParam_Whitening_on. A 9-bit LFSR is used to generate a random sequence. The payload and 2-byte CRC checksum is then XORed with this random sequence as shown in Figure 47. The data is de-whitened on the receiver side by XORing with the same random sequence. Payload whitening/de-whitening is thus made transparent for the user, who still provides/retrieves NRZ data to/from the FIFO. L F S R P o ly n o m ia l = X 9 + X 5 + 1 X8 X7 X6 X5 X4 X3 X2 X1 X0 T ran sm it d ata W hite ne d d ata Figure 47: Data Whitening 5.5.7. Interrupt Signal Mapping Tables below give the description of the interrupts available in Packet mode. Rev 7 - Sept 2nd, 2008 Page 54 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Table 23: Interrupt Mapping in Rx and Stby in Packet Mode Rx_stby_irq_x 00 (d) 01 10 11 00 (d) 01 10 11 Rx Payload_ready Write_byte /Fifoempty Sync or Adrs_match* CRC_OK Fifofull RSSI Fifo_threshold Stby /Fifoempty Fifofull Fifo_threshold IRQ_0 IRQ_1 *The latter if Address filtering is enabled Tx Fifo_threshold /Fifoempty Fifofull Tx_done IRQ_0 IRQ_1 Tx_start_irq_0=0 (d) Tx_start_irq_0=1 Tx_irq_1=0 (d) Tx_irq_1=1 Table 24: Interrupt Mapping in Tx Packet Mode 5.5.8. uC Connections SX1211 IRQ_0 IRQ_1 NSS_CONFIG NSS_DATA SCK MOSI MISO uC Figure 48: uC Connections in Packet Mode Note that depending upon the application, some uC connections may not be needed: IRQ_0: if none of the relevant IRQ sources are used. In this case, leave floating. IRQ_1: if none of the relevant IRQ sources are used. In this case, leave floating. MISO: if no read register access is needed and the chip is used in Tx mode only. In this case, pull up to VDD through a 100 k resistor. In addition, DATA pin (unused in packet mode) should be pulled-up to VDD through a 100 k Please refer to Table 13 for the SX1211's pin configuration. resistor. Rev 7 - Sept 2nd, 2008 Page 55 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 5.5.9. Packet Mode Example Configure all data processing related registers listed below appropriately. In this example we assume CRC is enabled with autoclear on. Table 25: Relevant Configuration Registers in Packet Mode (data processing related only) Data_mode_x Fifo_size Fifo_thresh Rx_stby_irq_0 Rx_stby_irq_1 Tx_irq_1 Tx_start_irq_0 Sync_size Sync_tol Sync_value Manchester_on Payload_length Node_adrs Pkt_format Preamble_size Whitening_on CRC_on Adrs_filt CRC_autoclr Fifo_stby_access Tx X X X Rx X X X X X Description Defines data operation mode ( Packet) Defines FIFO size Defines FIFO threshold Defines IRQ_0 source in Rx & Stby modes Defines IRQ_1 source in Rx & Stby modes Defines IRQ_1 source in Tx mode Defines Tx start condition and IRQ_0 source Defines Sync word size Defines the error tolerance on Sync word detection Defines Sync word value Enables Manchester encoding/decoding Length in fixed format, max Rx length in variable format Defines node address for Rx address filtering Defines packet format (fixed or variable length) Defines the size of preamble to be transmitted Enables whitening/de-whitening process Enables CRC calculation/check Enables and defines address filtering Enables FIFO autoclear if CRC failed Defines FIFO access in Stby mode MCParam IRQParam RXParam SYNCParam X X X X X (1) X X X X X X X X X X X X X X X X X PKTParam X (1) fixed format only Tx Mode: Program Tx start condition and IRQs: Start Tx when FIFO not empty (Tx_start_irq_0=1) and IRQ_1 mapped to Tx_done (Tx_irq_1=1) Go to Stby mode Write all payload bytes into FIFO (Fifo_stby_access=0, Stby interrupts can be used if needed) Go to Tx mode. When Tx is ready (automatically handled) Tx starts (Tx_start_irq_0=1). Wait for Tx_done interrupt (+1 bit period) Go to Sleep mode Rx Mode: Program Rx/Stby interrupts: IRQ_0 mapped to /Fifoempty (Rx_stby_irq_0=10) and IRQ_1 mapped to CRC_OK (Rx_stby_irq_1=00) Go to Rx (note that Rx is not ready immediately, see section 7.3.1 Wait for CRC_OK interrupt Go to Stby Read payload bytes from FIFO until /Fifoempty goes low. (Fifo_stby_access =1) Go to Sleep mode 5.5.10. Additional Information If the number of bytes filled for transmission is greater than the actual length of the packet to be transmitted and Tx_start_irq_0 = 1, then the FIFO is cleared after the packet has been transmitted. Thus the extra bytes in the Rev 7 - Sept 2nd, 2008 Page 56 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING FIFO are lost. On the other hand if Tx_start_irq_0 = 0 then the extra bytes are kept into the FIFO. This opens up the possibility of transmitting more than one packet by filling the FIFO with multiple packet messages. It is not possible to receive multiple packets. Once a packet has been received and filled into the FIFO all its content needs to be read i.e. the FIFO must be empty for a new packet reception to be initiated. The Payload_ready interrupt goes high when the last payload byte is available in the FIFO and remains high until all its data are read. Similar behavior is applicable to Adrs_match and CRC_OK interrupts. The CRC result is available in the CRC_status bit as soon as the CRC_successful and Payload_ready interrupt sources are triggered. In Rx mode, CRC_status is cleared when the complete payload has been read from the FIFO. If the payload is read in Stby mode, then CRC_status is cleared when the user goes back to Rx mode and a new Sync word is detected. The Fifo_fill_method and Fifo_fill bits don't have any meaning in the Packet mode and should be set to their default values only. Rev 7 - Sept 2nd, 2008 Page 57 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 6. Configuration and Status Registers 6.1. General Description Table 26 sums-up the control and status registers of the SX1211: Table 26: Registers List Name MCParam IRQParam RXParam SYNCParam TXParam OSCParam PKTParam Size 13 x 8 3x8 6x8 4x8 1x8 1x8 4x8 Address 0 - 12 13 - 15 16 - 21 22 - 25 26 27 28 - 31 Description Main parameters common to transmit and receive modes Interrupt registers Receiver parameters Pattern Transmitter parameters Crystal oscillator parameters Packet handler parameters 6.2. Main Configuration Register - MCParam The detailed description of the MCParam register is given in Table 27. Table 27: MCParam Register Description Name Bits Address (d) RW Description Transceiver mode: 000 sleep mode - Sleep 001 stand-by mode - Stby (d) 010 frequency synthesizer mode - FS 011 receive mode - Rx 100 transmit mode - Tx Frequency band: 00 902 - 915 MHz 01 915 - 928 MHz (d) 10 950 - 960 MHz or 863 - 870 MHz (Application Circuit dependant) Fine VCO trimming: 00 Vtune determined by tank inductors values (d) 01 Vtune + 60 mV typ. 10 Vtune + 120 mV typ. 11 Vtune + 180 mV typ. Selection between the two sets of frequency dividers of the PLL, Ri/Pi/Si 0 R1/P1/S1 selected(d) 1 R2/P2/S2 selected Modulation type: 01 OOK 10 FSK (d) Data operation mode LSB (refer to Data_Mode_1 (Bit 2 Addr 1) OOK demodulator threshold type: 00 fixed threshold mode 01 peak mode (d) 10 average mode 11 reserved Chip_mode 7-5 0 r/w Freq_band 4-3 0 r/w VCO_trim 2-1 0 r/w RPS_select 0 0 r/w Modul_select Data_mode_0 7-6 5 1 1 r/w r/w OOK_thresh_type 4-3 1 r/w Rev 7 - Sept 2nd, 2008 Page 58 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Data operation mode's MSB. Cf. Data_mode_0 (Bit 5 Addr 1) Data_mode_1 Data_mode_0 Data Operation Bit 2 addr 1 Bit 5 addr 1 Mode 0 0 Continuous (d) 0 1 Buffered 1 x Packet Gain on the IF chain: 00 maximal gain (0dB) (d) 01 -4.5 dB -9dB 10 11 -13.5 dB Single side frequency deviation in FSK Transmit mode: Refer to sections 3.3.4 and 3.3.5 Fdev = Data_mode_1 2 1 r/w IF_gain 1-0 1 r/w Freq_dev 7-0 2 r/w f XTAL , 0 D 255, where D is the value in the register. 32 (D + 1) Res BR 7 3 r/w (d): D = "00000011" => Fdev = 100 kHz Reserved (d): "0" Bit Rate = f XTAL 64 (C + 1) , 0 C 127, where C is the value in the register. 6-0 3 r/w (d): C = "0000111" => Bit Rate = 25 kb/s NRZ OOK_ floor_thresh 7-0 4 r/w Floor threshold in OOK Rx mode. By default 6 dB. (d): "00001100" assuming 0.5 dB RSSI step FIFO size selection: 00 16 bytes (d) 01 32 bytes 10 48 bytes 11 64 bytes FIFO threshold for interrupt source (Cf section 5.2.2.3) (d): B = "001111" R counter, active when RPS_select="0" (d):77h; default values of R1, P1, S1 generate 915.0 MHz in FSK mode P counter, active when RPS_select="0" (d): 64h; default values of R1, P1, S1 generate 915.0 MHz in FSK mode S counter, active when RPS_select="0" (d): 32h; default values of R1, P1, S1 generate 915.0 MHz in FSK mode R counter, active when RPS_select="1" (d): 74h; default values of R2, P2, S2 generate 920.0 MHz in FSK mode P counter, active when RPS_select="1" (d): 62h; default values of R2, P2, S2 generate 920.0 MHz in FSK mode S counter, active when RPS_select="1" (d): 32h; default values of R2, P2, S2 generate 920.0 MHz in FSK mode Reserved (d): "001" Ramp control of the rise and fall times of the Tx PA regulator output voltage in OOK mode: 00 3us 01 8.5 us 10 15 us 11 23 us (d) Reserved (d):"000" Fifo_size 7:6 5 r/w Fifo_thresh R1 P1 S1 R2 P2 S2 Res 5-0 7-0 7-0 7-0 7-0 7-0 7-0 7-5 5 6 7 8 9 10 11 12 r/w r/w r/w r/w r/w r/w r/w r/w PA_ramp 4-3 12 r/w Res 2-0 12 r/w Rev 7 - Sept 2nd, 2008 Page 59 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 6.3. Interrupt Configuration Parameters - IRQParam The detailed description of the IRQParam register is given in Table 28. Table 28: IRQParam Register Description Name Bits Address (d) RW Description IRQ_0 source in Rx and Standby modes: If Data_mode(1:0) = 00 (Continuous mode): 00 Sync (d) RSSI 01 Sync 10 Sync 11 If Data_mode(1:0) = 01 (Buffered mode): 00 - (d) 01 Write_byte 10 /Fifoempty* 11 Sync If Data_mode(1:0) = 1x (Packet mode): 00 Payload_ready (d) 01 Write_byte /Fifoempty* 10 11 Sync or Adrs_match (the latter if address filtering is enabled) *also available in Standby mode (Cf sections 5.4.4 and 5.5.7) IRQ_1 source in Rx and Standby modes: If Data_mode(1:0) = 00 (Continuous mode): xx DCLK If Data_mode(1:0) = 01 (Buffered mode): 00 - (d) 01 Fifofull* 10 RSSI 11 Fifo_threshold* If Data_mode(1:0) = 1x (Packet mode): 00 CRC_ok (d) 01 Fifofull* 10 RSSI 11 Fifo_threshold* *also available in Standby mode (Cf sections 5.4.4 and 5.5.7) IRQ_1 source in Tx mode: If Data_mode(1:0) = 00 (Continuous mode): x DCLK If Data_mode(1:0) = 01 (Buffered mode) or 1x (Packet mode): 0 Fifofull (d) 1 Tx_done Fifofull IRQ source Goes high when FIFO is full. /Fifoempty IRQ source Goes low when FIFO is empty Goes high when an overrun error occurred. Writing a 1 clears flag and FIFO FIFO filling method (Buffered mode only): Rx_stby_irq_0 7-6 13 r/w Rx_stby_irq_1 5-4 13 r/w Tx_irq_1 3 13 r/w Fifofull /Fifoempty Fifo_overrun_clr Fifo_fill_method Rev 7 - Sept 2nd, 2008 2 1 0 7 13 13 13 14 r r r/w/ c r/w Page 60 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 0 Automatically starts when a sync word is detected (d) 1 Manually controlled by Fifo_fill FIFO filling status/control (Buffered mode only): If Fifo_fill_method = `0': (d) Fifo_fill 6 14 r/w/ c Goes high when FIFO is being filled (sync word has been detected) Writing `1' clears the bit and waits for a new sync word (if Fifo_overrun_clr=0) If Fifo_fill_method = `1': 0 Stop filling the FIFO Start filling the FIFO 1 Tx_done IRQ source Goes high when the last bit has left the shift register. Tx start condition and IRQ_0 source: Tx_done 5 14 r If Data_mode(1:0) = 01 (Buffered mode): 0 1 Tx_start_irq_0 4 14 r/w Tx starts if FIFO is full, IRQ_0 mapped to /Fifoempty (d) Tx starts if FIFO is not empty, IRQ_0 mapped to /Fifoempty If Data_mode(1:0) = 1x (Packet mode): 0 Start transmission when the number of bytes in FIFO is greater than or equal to the threshold set by MCParam_Fifo_thresh parameter (Cf section 5.2.2.3), IRQ_0 mapped to Fifo_threshold (d) 1 Tx starts if FIFO is not empty, IRQ_0 mapped to /Fifoempty (d): "0", should be set to "1". Note: "0" disables the RSSI IRQ source. It can be left enabled at any time, and the user can choose to map this interrupt to IRQ0/IRQ1 or not. RSSI IRQ source: Goes high when a signal above RSSI_irq_thresh is detected Writing `1' clears the bit PLL status: 0 not locked 1 locked Writing a `1' clears the bit PLL_lock detect flag mapped to pin 23: 0 Lock detect disabled, pin 23 is High-Z 1 Lock detect enabled(d) RSSI threshold for interrupt (coded as RSSI) (d): "00000000" Res 3 14 r/w r/w/ c r/w/ c RSSI_irq 2 14 PLL_locked 1 14 PLL_lock_en RSSI_irq_thresh 0 7-0 14 15 r/w Rev 7 - Sept 2nd, 2008 Page 61 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 6.4. Receiver Configuration parameters - RXParam The detailed description of the RXParam register is given in Table 29. Table 29: RXParam Register Description Name Bits Address (d) RW Description Typical single sideband bandwidth of the passive low-pass filter. 65 kHz PassiveFilt = 0000 0001 82 kHz 109 kHz 0010 0011 137 kHz 157 kHz 0100 0101 184 kHz 211 kHz 0110 0111 234 kHz 1000 262 kHz 321 kHz 1001 1010 378 kHz (d) 1011 414 kHz 1100 458 kHz 1101 514 kHz 1110 676 kHz 1111 987 kHz Sets the receiver bandwidth. For BW information please refer to sections 3.4.5 (FSK) and 3.4.6 (OOK). PassiveFilt 7-4 16 r/w ButterFilt 3-0 16 r/w f c = f 0 + 200kHz. f xtal MHz 1 + Val ( ButterFilt ) . 12.8MHz 8 (d): "0011" => fC -f0 = 100 kHz Central frequency of the polyphase filter (100kHz recommended): PolypFilt_center 7-4 17 r/w f 0 = 200kHz. Fxtal MHz 1 + Val ( PolypFilt _ center ) . 12.8MHz 8 Res PolypFilt_on 3-0 7 17 18 r/w r/w Bitsync_off 6 18 r/w Sync_on 5 18 r/w Sync_size 4-3 18 r/w Sync_tol 2-1 18 r/w Res Rev 7 - Sept 2nd, 2008 0 18 r/w (d):"0011" => f0 = 100 kHz Reserved (d): "1000" Enable of the polyphase filter, in OOK Rx mode: 0 off (d) 1 on Bit synchronizer: control in Continuous Rx mode: 0 on (d) 1 off Sync word recognition: 0 off (d) 1 on Sync word size: 00 8 bits 01 16 bits 10 24 bits 11 32 bits (d) Number of errors tolerated in the Sync word recognition: 00 0 error (d) 01 1 error 10 2 errors 11 3 errors Reserved (d):"0" Page 62 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Name Res RSSI_val Bits 7-0 7-0 Address (d) 19 20 RW r/w r Description Reserved (d): "00000111" RSSI output, 0.5 dB / bit Note: READ-ONLY (not to be written) Size of each decrement of the RSSI threshold in the OOK demodulator 000 0.5 dB (d) 100 3.0 dB 1.0 dB 101 4.0 dB 001 010 1.5 dB 110 5.0 dB 2.0 dB 111 6.0 dB 011 Period of decrement of the RSSI threshold in the OOK demodulator: 000 once in each chip period (d) 001 once in 2 chip periods once in 4 chip periods 010 011 once in 8 chip periods twice in each chip period 100 101 4 times in each chip period 8 times in each chip period 110 111 16 times in each chip period Cutoff frequency of the averaging for the average mode of the OOK threshold in demodulator 00 fC BR / 8. (d) 01 Reserved 10 Reserved 11 fC BR / 32. OOK_thresh_step 7-5 21 r/w OOK_thresh_dec _period 4-2 21 r/w OOK_avg_thresh _cutoff 1-0 21 r/w 6.5. Sync Word Parameters - SYNCParam The detailed description of the SYNCParam register is given in Table 30. Table 30: SYNCParam Register Description Name Sync_value(31:24) Sync_value(23:16) Sync_value(15:8) Sync_value(7:0) Bits 7-0 7-0 7-0 7-0 Address (d) 22 23 24 25 RW r/w Description st 1 Byte of Sync word (d): "00000000" nd 2 Byte of Sync word (only used if Sync_size 00) (d): "00000000" rd 3 Byte of Sync word (only used if Sync_size = 1x) (d): "00000000" th 4 Byte of Sync word (only used if Sync_size = 11) (d): "00000000" Rev 7 - Sept 2nd, 2008 Page 63 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 6.6. Transmitter Parameters - TXParam The detailed description of the TXParam register is given in Table 31. Table 31: TXParam Register Description Name InterpFilt Bits 7-4 Address (d) 26 RW r/w Description Tx Interpolation filter cut off frequency: fc = 200kHz. Pout 3-1 26 r/w Fxtal MHz 1 + Val ( InterpFiltTx ) . 12.8MHz 8 Res 0 26 r/w (d): "0111" => fC = 200 kHz Tx output power (1 step 3 dB): 13 dBm 000 13 dBm -1 step (d) 001 010 13 dBm - 2 steps 13 dBm - 3 steps 011 100 13 dBm - 4 steps 101 13 dBm - 5 steps 110 13 dBm - 6 steps 111 13 dBm - 7 steps Reserved (d): "0" 6.7. Oscillator Parameters - OSCParam The detailed description of the OSCParam register is given in Table 32. Table 32: OSCParam Register Description Name Clkout_on Bits 7 Address (d) 27 RW r/w Description Clkout control 0 Disabled Enabled, Clk frequency set by Clkout_freq (d) 1 Frequency of the signal provided on CLKOUT: fclkout = f xtal if Clkout_freq = "00000" Clkout_freq 6-2 27 r/w fclkout = Res 1-0 27 r/w f xtal otherwise 2 Clkout _ freq (d): 01111 (= 427 kHz) Reserved (d): "00" Rev 7 - Sept 2nd, 2008 Page 64 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 6.8. Packet Handling Parameters - PKTParam The detailed description of the PKTParam register is given in Table 33. Table 33: PKTParam Register Description Name Manchester_on Bits 7 Address (d) 28 RW r/w Description Enable Manchester encoding/decoding: off (d) 0 on 1 If Pkt_format=0, payload length. If Pkt_format=1, max length in Rx, not used in Tx. (d): "0000000" Node's local address for filtering of received packets. (d): 00h Packet format: 0 fixed length (d) 1 variable length Size of the preamble to be transmitted: 00 1 byte 01 2 bytes 10 3 bytes (d) 4 bytes 11 Whitening/dewhitening process: 0 off (d) 1 on CRC calculation/check: 0 off 1 on (d) Address filtering of received packets: 00 off (d) 01 Node_adrs accepted, else rejected. Node_adrs & 0x00 accepted, else rejected. 10 11 Node_adrs & 0x00 & 0xFF accepted, else rejected. CRC check result for current packet (READ ONLY): 0 Fail 1 Pass FIFO auto clear if CRC failed for current packet: 0 on (d) 1 off FIFO access in standby mode: 0 Write (d) 1 Read Reserved (d): "000000" Payload_length 6-0 28 r/w Node_adrs Pkt_format 7-0 7 29 30 r/w r/w Preamble_size 6-5 30 r/w Whitening_on 4 30 r/w CRC_on 3 30 r/w Adrs_filt 2-1 30 r/w CRC_status 0 30 r CRC_autoclr 7 31 r/w Fifo_stby_access 6 31 r/w Res 5-0 31 r/w Rev 7 - Sept 2nd, 2008 Page 65 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7. Application Information 7.1. Crystal Resonator Specification Table 34 shows the crystal resonator specification for the crystal reference oscillator circuit of the SX1211. This specification covers the full range of operation of the SX1211 and is employed in the reference design (see section 7.5.3). Table 34: Crystal Resonator Specification Name Fxtal Cload Rm Co Fxtal Fxtal(T) Description Nominal frequency Load capacitance for Fxtal Motional resistance Shunt capacitance Calibration tolerance at 25+/-3 C Stability over temperature range [-40 ; +85 C C] Ageing tolerance in first 5 years Min. 9 10 1 -15 -2 0 -2 Typ. 12.800 15 Max. 15 16.5 100 7 +15 +20 +2 Unit MHz pF ohms pF ppm ppm ppm/year Fxtal(t) Note that the initial frequency tolerance, temperature stability and ageing performance should be chosen in accordance with the target operating temperature range and the receiver bandwidth selected. 7.2. Software for Frequency Calculation The R1, P1, S1, and R2, P2, S2 dividers are configured over the SPI interface and programmed by 8 bits each, at addresses 6 to 11. The frequency pairs may hence be switched in a single SPI cycle. 7.2.1. GUI To aid the user with calculating appropriate R, P and S values, software is available to perform the frequency calculation. The SX1211 PLL frequency Calculator Software can be downloaded from the Semtech website. 7.2.2. .dll for Automatic Production Bench The Dynamically Linked Library (DLL) used by the software to perform these calculations is also provided, free of charge, to users, for inclusion in automatic production testing. Key benefits of this are: No hand trimming of the reference frequency required: the actual reference frequency of the Device Under Test (DUT) can be easily measured (e.g. from the CLKOUT output of the SX1211) and the tool will calculate the best frequencies to compensate for the crystal initial error. Channel plans can be calculated and stored in the application's memory, then adapted to the actual crystal oscillator frequency. 7.3. Switching Times and Procedures As an ultra-low power device, the SX1211 can be configured for low minimum average power consumption. To minimize consumption the following optimized transitions between modes are shown. Rev 7 - Sept 2nd, 2008 Page 66 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.3.1. Optimized Receive Cycle The lowest-power Rx cycle is the following: SX1211 IDD IDDR 3.0mA typ. IDDFS 1.3mA typ. IDDST 65uA typ. IDDSL 100nA typ. Rx time Time SX1211 can be put in Any other mode Wait TS_RE Receiver is ready : -RSSI sampling is valid after a 1/Fdev period -Received data is valid Wait TS_FS Set SX1211 in Rx mode Wait for Receiver settling Wait TS_OSC Set SX1211 in FS mode Wait for PLL settling Set SX1211 in Standby mode Wait for XO settling Figure 49: Optimized Rx Cycle Note: If the lock detect indicator is available on an external interrupt pin of the companion uC, it can be used to optimize TS_FS, without having to wait the maximum specified TS_FS. Rev 7 - Sept 2nd, 2008 Page 67 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.3.2. Optimized Transmit Cycle SX1211 IDD IDDT 16mA typ. @1dBm IDDFS 1.3mA typ. IDDST 65uA typ. IDDSL 100nA typ. Tx time Time SX1211 can be put in Any other mode Wait TS_TR Data transmission can start in Continuous and Buffered modes Wait TS_FS Set SX1211 in Tx mode Packet mode starts its operation Wait TS_OSC Set SX1211 in FS mode Wait for PLL settling Set SX1211 in Standby mode Wait for XO settling Figure 50: Optimized Tx Cycle Note: As stated in the preceding section, TS_FS time can be improved by using the external lock detector pin as external interrupt trigger. Rev 7 - Sept 2nd, 2008 Page 68 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.3.3. Transmitter Frequency Hop Optimized Cycle SX1211 IDD IDDT 16mA typ. @1dBm IDDFS 1.3mA typ. Time Wait TS_TR SX1211 is now ready for data transmission Wait TS_HOP Set SX1211 back in Tx mode 1. Set R2/P2/S2 2. Set SX1211 in FS mode, change MCParam_Band if needed, then switch from R1/P1/S1 to R2/P2/S2 SX1211 is in Tx mode On channel 1 (R1/P1/S1) Figure 51: Tx Hop Cycle Rev 7 - Sept 2nd, 2008 Page 69 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.3.4. Receiver Frequency Hop Optimized Cycle SX1211 IDD IDDR 3mA typ IDDFS 1.3mA typ. Time Wait TS_RE SX1211 is now ready for data reception Wait TS_HOP Set SX1211 back in Rx mode 1. Set R2/P2/S2 2. Set SX1211 in FS mode, change MCParam_Band if needed, then switch from R1/P1/S1 to R2/P2/S2 SX1211 is in Rx mode On channel 1 (R1/P1/S1) Figure 52: Rx Hop Cycle Note: it is also possible to move from one channel to the other one without having to switch off the receiver. This method is faster, and overall draws more current. For timing information, please refer to TS_RE_HOP on Table 8. Rev 7 - Sept 2nd, 2008 Page 70 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.3.5. Rx Tx and Tx Rx Jump Cycles SX1211 IDD IDDT 16mA typ. @1dBm IDDR 3.0mA typ. Time Wait TS_RE SX1211 is ready to receive data Set SX1211 in Rx mode Wait TS_TR SX1211 is now ready for data transmission SX1211 is in Rx mode Set SX1211 in Tx mode Figure 53: Rx Tx Rx Cycle Rev 7 - Sept 2nd, 2008 Page 71 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.4. Reset of the Chip A power-on reset of the SX1211 is triggered at power up. Additionally, a manual reset can be issued by controlling pin 13. 7.4.1. POR If the application requires the disconnection of VDD from the SX1211, despite of the extremely low Sleep Mode current, the user should wait for 10 ms from of the end of the POR cycle before commencing communications over the SPI bus. Pin 13 (TEST8) should be left floating during the POR sequence. VDD Pin 13 (output) Undefined Wait for 10 ms Chip is ready from this point on Figure 54: POR Timing Diagram Please note that any CLKOUT activity can also be used to detect that the chip is ready. 7.4.2. Manual Reset A manual reset of the SX1211 is possible even for applications in which VDD cannot be physically disconnected. Pin 13 should be pulled high for a hundred microseconds, and then released. The user should then wait for 5 ms before using the chip. VDD > 100 us Wait for 5 ms Chip is ready from this point on Pin 13 (input) High-Z ''1'' High-Z Figure 55: Manual Reset Timing Diagram Please note that while pin 13 is driven high, an over current consumption of up to ten milliamps can be seen on VDD. Rev 7 - Sept 2nd, 2008 Page 72 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.5. Reference Design It is recommended that this reference design (i.e. schematics, placement, layout, BOM,) is replicated in the final application board to guarantee optimum performance. 7.5.1. Application Schematic Figure 56: Reference Design Circuit Schematic The reference design area is represented by the dashed rectangle. C12 is a DC blocking capacitor which protects the SAW filter. It has been added for debug purposes could be removed for a direct antenna connection if there is no DC bias is expected at the antenna port. Please note that C10 and C11 are not used. 7.5.2. PCB Layout As illustrated in figures below, the layout has the following characteristics: very compact (9x19mm) => can be easily inserted even on very small PCBs standard PCB technology (2 layers, 1.6mm, std via & clearance) => low cost Its performance is quasi-insensitive to dielectric thickness => minimal design effort to transfer to other PCB technologies (thickness, # of layers, etc...) Rev 7 - Sept 2nd, 2008 Page 73 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING The layers description is illustrated in Figure 57: Signal (35um) Isolation (FR4, 1.6mm) Ground plane Figure 57: Reference Design`s Stackup The layout itself is illustrated in Figure 58. Please contact Semtech for gerber files. 19mm 9mm Figure 58: Reference Design Layout (top view) 7.5.3. Bill Of Material Table 35: Reference Design BOM Ref U1 U2 Q1 Value 868MHz 915MHz SX1211 869 MHz 915 MHz 12.8 MHz Tol (+/-) Techno Size TQFN-32 3.8*3.8 mm 5.0*3.2 mm Comment Plotted in section 7.5.4 Fundamental, Cload=15 pF Transceiver IC SAW Filter 15 ppm at 25 C AT-cut 20 ppm over -40/+85 C 2ppm/year max R1 1 1% R2 6.8 k 1% C1 1uF 15% X5R C2 1uF 15% X5R C3 220 nF 10% X7R C4 47 nF 10% X7R C5 100 nF 10% X7R C6 10 nF 10% X7R C7 680 pF 5% NPO C8 1.8 pF 0.25 pF NPO C9 22 pF 5% NPO L1, L2 8.2 nH 6.8 nH 0.2 nH Wire wound L3 100 nH 5% Wire wound L4 8.2 nH 5% Multilayer C10, C11 NC C12* 47pF 5% NPO *Not part of the ref. design (not required for direct antenna connection). 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 PA regulator Loop filter VDD decoupling Top regulator decoupling Digital regulator decoupling PA regulator decoupling VCO regulator decoupling Loop Filter Loop Filter Matching DC block and L4 adjust VCO tank inductors PA Choke Matching DC block Note: for battery powered applications, a high value capacitance should be implemented in parallel with C1 (typically 10 F) to offer a low impedance voltage source during startup sequences. Rev 7 - Sept 2nd, 2008 Page 74 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.5.4. SAW Filter Plot The following screenshot shows the plot of the SAW filter used on the reference design: 0 -10 -20 Attenuation [dB] -30 -40 -50 -60 -70 -80 400 600 800 1000 1200 Frequency [MHz] 1400 1600 1800 2000 Figure 59: 915 MHz SAW Filter Plot 0 -10 -20 Attenuation [dB] -30 -40 -50 -60 -70 -80 400 600 800 1000 1200 Frequency [MHz] 1400 1600 1800 2000 Figure 60: 869 MHz SAW Filter Plot 7.5.5. Ordering Information for Tools The modules described in section 7.5 can be ordered through your Semtech representative for evaluation purpose: Table 36: Tools Ordering Information Part Number SM1211E868 SM1211E915 SX1211SK868 SX1211SK915 Rev 7 - Sept 2nd, 2008 Description 2 layer RF module, 868 MHz band 2 layer RF module, 915 MHz band Full evalulation kit, including 2 SM1211E868, controller boards, antennas and cables Full evalulation kit, including 2 SM1211E915, controller boards, antennas and cables Page 75 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6. Reference Design Performance All the measurements visible on section 7.6 typical figures obtained under the following conditions, unless otherwise noted: Nominal VDD = 3.3 V Tests performed at room temperature: 25 +/-3 C C Center frequency 869 MHz or 915 MHz {R, P, S} triplets are those calculated by the software described in section 3.2.8. All register settings are default, except for those stated in the relevant sub-sections Maximum Output Power programmed on Pout tests All sensitivities are evaluated in Continuous mode, demodulating a PN15 sequence, BER=0.1% FSK sensitivities measured at 25kbps, Fdev=+/-50 kHz OOK sensitivities measured at 8kbps, with Fo=100 kHz. IF2 set to 100 kHz. On all Adjacent Channel Rejection (ACR), Blocking and Spurious Response Frequency tests, the unwanted signal is unmodulated. Bill of Materials as shown in section 7.5.3. In particular, a SAW filter is used (see its performance on section 7.5.4) The filter settings described on Table 37 and Table 38 were used for the measurements of section 7.6.5. Table 37: FSK Rx Filters vs. Bit Rate Bit Rate Fdev Filter Setting Addr 16 Hex FF E9 D6 B5 A4 A3 A3 72 72 72 72 41 41 41 41 41 41 Fdev + BR/2 kHz 250 166.7 125 100 83.3 71.4 62.5 55.6 50 45.5 41.7 41 40.5 39.6 38.3 35.8 34.3 Rx 3 dB BW Programmed kHz 400 250 175 150 125 100 100 75 75 75 75 50 50 50 50 50 50 Actual kHz 306 214 158 137 116 96 96 69 69 69 69 47 47 47 47 47 47 +/- ppm 62 53 37 41 36 27 37 15 21 26 30 7 7 8 10 12 14 Max. drift kbps 100 66.67 50 40 33.33 28.57 25 22.22 20 18.18 16.67 15.38 14.29 12.5 10 5 2 +/- kHz 200 133 100 80 67 57 50 44 40 36 33 33 33 33 33 33 33 Table 38: OOK Rx Filters vs. Bit Rate Bit Rate FO + BR Filter Setting Addr 16 Hex C1 C1 A0 A0 A0 A0 A0 Rx 3 dB BW Programmed kHz 150 150 125 125 125 125 125 Actual kHz 154 154 129 129 129 129 129 +/- ppm 41 46 22 23 27 30 30 Max. drift kbps 16.67 12.5 9.52 8 4.76 2.41 1.56 kHz 117 113 110 108 105 102 102 Rev 7 - Sept 2nd, 2008 Page 76 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.1. Sensitivity Flatness Sensitivity over the Frequency Band -90.0 -92.0 Sensitivity @ BER=0.1% -94.0 -96.0 -98.0 -100.0 -102.0 -104.0 -106.0 863 14.0 12.0 10.0 8.0 6.0 4.0 2.0 0.0 -2.0 870 SAW Ripple [dB] 864 865 866 867 868 869 Frequency [MHz] Sensitivity SAW Ripple Figure 61: Sensitivity Across the 868 MHz Band Sensitivity over the Frequency Band -90.0 -92.0 -94.0 Sensitivity [dBm] -96.0 -98.0 -100.0 -102.0 -104.0 -106.0 902 14.0 12.0 10.0 8.0 6.0 4.0 2.0 0.0 -2.0 928 SAW Ripple [dB] 904 906 908 910 912 914 916 918 920 922 924 926 Frequency [MHz] Sensitivity SAW Ripple Figure 62: Sensitivity Across the 915 MHz Band Notes: Measured in FSK mode only. OOK sensitivity characteristics will be similar. The sensitivity difference along the band remains inside the ripple performance of the SAW filter (the nominal passband of the 869 MHz SAW filter is 868 - 870 MHz) The SAW filter ripple response is referenced to its insertion loss at 869 MHz and 915 MHz for each filter. Rev 7 - Sept 2nd, 2008 Page 77 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.2. Sensitivity vs. LO Drift Sensitivity Loss vs. LO Drift 6.0 5.0 4.0 Sensitivity Loss [dB] 3.0 2.0 1.0 0.0 -1.0 -25 -20 -15 -10 -5 0 LO Drift [kHz] 5 10 15 20 25 Figure 63: FSK Sensitivity Loss vs. LO Drift Sensitivity Loss vs. LO Drift 6.0 5.0 4.0 Sensitivity Loss [dB] 3.0 2.0 1.0 0.0 -1.0 -100 -80 -60 -40 -20 0 LO Drift [kHz] 20 40 60 80 100 Figure 64: OOK Sensitivity Loss vs. LO Drift Notes: In FSK Mode, the default filter setting ("A3" at address $16) is kept, leading to Fc=96 kHz typ. In OOK Mode, "F3" is set at address $16, leading to (Fc-Fo)=95 kHz typ. The above ensures that the channel filter is wide enough, therefore characterizing the demodulator response, and NOT the filter response. Rev 7 - Sept 2nd, 2008 Page 78 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.3. Sensitivity vs. Receiver BW Sensitivity vs. Fc 1.0 0.0 50 Sensitivity Improvement [dB] => -1.0 100 150 200 250 300 -2.0 -3.0 -4.0 -5.0 -6.0 Fc of Active Filter [kHz] Figure 65: FSK Sensitivity vs. Rx BW Sensitivity Change vs. (Fc-Fo) 1.0 0.0 0 Sensitivity Improvement [dB] => -1.0 50 100 150 200 250 300 350 -2.0 -3.0 -4.0 -5.0 -6.0 Fc-Fo [kHz] Figure 66: OOK Sensitivity Change vs. Rx BW Rev 7 - Sept 2nd, 2008 Page 79 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.4. Sensitivity Stability over Temperature and Voltage Sensitivity Stability 1.5 1.0 Sensitivity Improvement [dB] => 0.5 0.0 2.10 -0.5 2.40 2.70 3.00 3.30 3.60 85 C 25 C 0 C -40 C -1.0 -1.5 -2.0 -2.5 VDD [V] Figure 67: Sensitivity Stability Note: The sensitivity performance is very stable over the VDD range, and the effect of high temperature is minimal. 7.6.5. Sensitivity vs. Bit Rate Sensitivity Change over BR 8.0 6.0 Sensitivity Improvement [dB] => 4.0 2.0 0.0 0 -2.0 -4.0 25 50 75 100 -6.0 -8.0 Bit Rate [kb/s] Figure 68: FSK Sensitivity vs. BR Rev 7 - Sept 2nd, 2008 Page 80 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Sensitivity Change over the BR 2.0 1.5 1.0 0.5 0.0 1.5 -0.5 -1.0 -1.5 -2.0 -2.5 Bit Rate [kbps] 4 6.5 9 11.5 14 16.5 Sensitivity Improvement [dB] => Figure 69: OOK Sensitivity vs. BR 7.6.6. Adjacent Channel Rejection ACR in FSK Mode 70 60 50 ACR [dB] 40 30 20 10 0 -1000 -800 -600 -400 -200 0 Offset [kHz] 200 400 600 800 1000 Figure 70: ACR in FSK Mode Rev 7 - Sept 2nd, 2008 Page 81 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING ACR in OOK Mode 60 50 40 30 ACR [dB] 20 10 0 -300 -200 -100 -10 0 100 200 300 -20 Offset [kHz] Figure 71: ACR in OOK Mode Notes: In FSK mode, the unwanted signal is unmodulated (as described in the EN 300-220 V2.1.1).Co-Channel Rejection (CCR, Offset = 0kHz) is positive due to the DC cancellation process of the zero-IF architecture In OOK mode, the polyphase filter efficiency is limited, thus limiting the adjacent channel rejection at 2xFo distance. 7.6.7. Output Power Flatness Pout Over the Frequency Band 12.0 4.0 10.0 2.0 6.0 -2.0 4.0 -4.0 2.0 -6.0 0.0 863 864 865 866 867 868 869 -8.0 870 Frequency [MHz] Pout SAW Ripple Figure 72: Pout for 869 MHz Band Operation Rev 7 - Sept 2nd, 2008 Page 82 of 92 SAW Ripple [dB] 8.0 Pout [dBm] 0.0 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Pout over the Frequency Band 12.00 4.0 10.00 2.0 6.00 -2.0 4.00 -4.0 2.00 -6.0 0.00 902 904 906 908 910 912 914 916 918 920 922 924 926 -8.0 928 Frequency [MHz] Pout SAW Ripple Figure 73: Pout for 915 MHz Band Operation Notes: As noted in section 7.5.4, the 869 MHz SAW filter does not cover the whole European 863 - 870 MHz frequency band when used in a 50 ohms environment. Hence the output power degradation at the lowest frequencies. For applications in the 863 - 870 MHz band it is recommended that an appropriate SAW filter be implemented or that the SAW response tuned by external matching. The SAW filter ripple references are the insertion loss of each SAW at 869 MHz and 915 MHz. 7.6.8. Pout and IDD vs. PA Setting Pout & IDD vs. TXParam_Pout Setting 12.0 28.00 26.00 8.0 24.00 4.0 Pout [dBm] 22.00 20.00 0.0 18.00 -4.0 16.00 14.00 -8.0 12.00 -12.0 0 1 2 3 4 5 6 7 TXParam_Pout [d] Pout IDD 10.00 Figure 74: Pout and IDD at all PA Settings, 869 MHz Rev 7 - Sept 2nd, 2008 Page 83 of 92 SAW Ripple [dB] 8.00 Pout [dBm] 0.0 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING Pout & IDD vs. TXParam_Pout Setting 12.0 10.0 8.0 6.0 4.0 Pout [dBm] 2.0 0.0 -2.0 -4.0 -6.0 -8.0 -10.0 -12.0 0 1 2 3 4 5 6 7 TXParam_Pout [d] Pout IDD 14.0 12.0 10.0 24.0 IDD [mA] 22.0 20.0 18.0 16.0 30.0 28.0 26.0 Figure 75: Pout and IDD at all PA Settings, 915 MHz Note: +10dBm typ. Output power is achievable, even at SAW filter's output. 7.6.9. Pout Stability over Temperature and Voltage Pout Stability 1.0 0.5 Pout Improvement [dB] => 0.0 2.1 2.4 2.7 3.0 3.3 3.6 85 C -0.5 25 C -40 C 0 C -1.0 -1.5 -2.0 VDD [V] Figure 76: Pout Stability The output power is not sensitive to the supply voltage, and it decreases slightly when temperature rises. Rev 7 - Sept 2nd, 2008 Page 84 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.10. Transmitter Spectral Purity Figure 77: 869 MHz Spectral Purity DC-1GHz Figure 78: 869 MHz Spectral Purity 1-6GHz Rev 7 - Sept 2nd, 2008 Page 85 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.11. OOK Channel Bandwidth The OOK bit rate ranges form 1.56 to 16.7 kbps. It is interesting to note that, for the lowest bit rates, a channel spacing approaching 200 kHz is achievable: Figure 79: OOK Spectrum - 2kbps Figure 80: OOK Spectrum - 8kbps Figure 81: OOK Spectrum - 16.7kbps Notes: The test conditions are: Fdev=100 kHz, TXParam_InterpFilt = 200 kHz Rev 7 - Sept 2nd, 2008 Page 86 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.12. FSK Spectrum in Europe Figure 82 shows the minimal spectral occupation achievable in the European band, keeping in mind that the minimum frequency deviation that a SX1211 receiver can accept is 33 kHz. If the companion receiver can bear smaller frequency deviations, the range of modulation bandwidth can be further decreased. Figure 82: FSK - 1.56kbps - +/-33 kHz The default configuration of the SX1211 yields the bandwidth visible on Figure 83: Figure 83: FSK - 25 kbps - +/-50 kHz Figure 84 shows the maximal bit rate and frequency deviation that can fit in the 868 to 868.6 MHz European subband: Figure 84: FSK - 40 kbps - +/-40 kHz Rev 7 - Sept 2nd, 2008 Page 87 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.13. Digital Modulation Schemes FCC Part 15.247 allows for systems employing digital modulation techniques to transmit up to 1 W, provided that the 6 dB bandwidth of the signal is at least 500 kHz and that the power spectral density does not exceed 8dBm in any 3 kHz bandwidth. The SX1211 can actually meet these constraints whilst transmitting at the maximum output power of the device of typ. 10dBm, thanks to the built-in whitening process described in section 5.5.6.2: Figure 85: DTS 6dB Bandwidth Figure 86: DTS Power Spectral Density Conditions: Pout = +10.6dBm Fdev = +/-200kHz BR=100 kbps (Chip rate=100kCps, as data whitening is enabled) Packet mode, data whitening enabled Note: Manchester encoding allows meeting an even lower power spectral density, at the expense of the bit rate efficiency. Rev 7 - Sept 2nd, 2008 Page 88 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 7.6.14. Current Stability over Temperature and Voltage Sleep Mode Current 1200 Standby Mode Current 100 90 1000 80 800 Isleep [nA] 85 C 600 25 C 0C -40 C 400 70 60 85 C 50 40 30 20 10 25 C 0C -40 C 200 0 2.1 2.4 2.7 VDD [V] 3 3.3 3.6 Istby [uA] 0 2.1 2.4 2.7 VDD [V] 3 3.3 3.6 FS Mode Current 2.00 1.80 1.60 3.00 4.00 3.50 Rx Mode Current 1.40 1.20 Ifs [mA] 1.00 0.80 0.60 1.00 2.50 25 C 0C -40 C Irx [mA] 85 C 85 C 2.00 1.50 25 C 0C -40 C 0.40 0.20 0.00 2.1 2.4 2.7 VDD [V] 3 3.3 3.6 0.50 0.00 2.1 2.4 2.7 VDD [V] 3 3.3 3.6 Tx Mode Current (Max Output Power) 30.0 25.0 20.0 Itx [mA] TXLVL=000 85 C 15.0 25 C -40 C 0 C 10.0 5.0 0.0 2.1 2.4 2.7 VDD [V] 3.0 3.3 3.6 Figure 87: IDD vs. Temp and VDD Rev 7 - Sept 2nd, 2008 Page 89 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 8. Packaging Information 8.1. Package Outline Drawing SX1211 is available in a 32-lead TQFN package as shown in Figure 88 below. Figure 88: Package Outline Drawing 8.2. PCB Land Pattern Figure 89: PCB Land Pattern Rev 7 - Sept 2nd, 2008 Page 90 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 8.3. Tape & Reel Specification Direction of Feed Carrier Tape Tape Width(W) Pocket Pitch (P) Ao/Bo Ko 1.10 +/-0.1 Reel Size Reel Reel Width 12.4 Min.Trail er Length 400 Min. Leader Length 400 QTY per Reel 3000 12 8 5.25 +/-0.3 +/-0.1 +/-0.2 Notes: *all dimensions in mm *single sprocket holes 330.2 Figure 90: Tape & Reel Dimensions Rev 7 - Sept 2nd, 2008 Page 91 of 92 www.semtech.com SX1211 ADVANCED COMMUNICATIONS & SENSING 9. Revision History Revision 5 Increase maximum Bit Rate in FSK Update minimum XO frequency Add the manual reset description Insert decoupling recommendation for battery operated systems Add Tools ordering information Revision 6 Update SPI speed Clarify default fc value in Table 29 Clarify MISO state in SPI timing figures Improve ESD rating description Revision 7 Describe PLL_LOCK pin state in Table 13 Improve note in section 5.4.1 Clarify Table 5 measurement conditions Clarify /Fifoempty interrupt source behavior Correct Vtune in Figure 5 Adjust VCO tuning range in section 3.2.5.2 10. Contact Information Semtech Corporation Advanced Communication and Sensing Products Division 200 Flynn Road, Camarillo, CA 93012 Phone (805) 498-2111 Fax: (805) 498-3804 (c) Semtech 2008 All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Semtech. assumes no responsibility or liability whatsoever for any failure or unexpected operation resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified range. SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER'S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. Rev 7 - Sept 2nd, 2008 Page 92 of 92 www.semtech.com |
Price & Availability of SX1211I084T
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |