![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Power Amplifier Product Features * Small size by using simple matching circuit board * High Efficiency * Single Supply Voltage * High Linearity, 10W Power * Heat sink 99.9% copper, gold plate * High Productivity * Low Manufacturing Cost * GaAs MESFET RFM0415-10 Application * TRS * RF Sub-Systems * Base Station Package : DP-36 Description The power amplifier module is designed for base stations and cell extenders as cellular and TRS, GSM , IMT-2000, ISM, MMDS frequency systems. GaAs MESFET is used and attached on a copper sub carrier. It is connected by using bias and in/out matching circuit method with gold wire bonding. The bias and matching circuit are designed much simpler than other circuits for silicon IC's, LDMOS because GaAs MESFET is operated by low supply voltage whereas others are operated by high supply voltage. For better thermal conductivity, enhanced mode PCB was used in the 99.9% copper gold plate heat sink. This simplicity results cost competitiveness and performance enhancement. Specifications PARAMETER Frequency Range (MHz) Small Signal Gain (dB) Gain Flatness (Max.) Gain Variation Over Temp VSWR (Input) Output P1dB Vcc / Idc OIP3 @ tone / 27 dBm Noise Figure (Typ.) Shut Down (On/Off) In/Out Connectors Operating Temp Range Dimensions (WxLxH) NOTE * RFM : Internally Matched Module * RFH : Housing Type : RF Connector : SMA Female Min Typ 380 ~ 450 16 0.5dB @ 50MHz BW 0.5dB 2:1 Max 1.0dB 37dBm 48 dBm 38 dBm 9V / 1.2A 49 dBm 5 dB 5V @ 25 / 0V SMA Female (50 ) -20C ~ +70C Dimensions in mm Functional Diagram 29.0 x 30.2 x 9.0 [mm] (RFM) 48.0 x 54.2 x 22.0 [mm] (RFH) Tel : 82-31-250-5011 rfsales@rfhic.com All specifications may change without notice. Version 5.4 Power Amplifier RFM0415-10 Performance Charts (Vd=9V, Id=1.2A, T=25) Tel : 82-31-250-5011 rfsales@rfhic.com All specifications may change without notice. Version 5.4 Power Amplifier Package Dimensions (Type: DP-36) RFM0415-10 Pin NO 1 2 3 Function GND RF IN GND Pin NO 6 5 4 Installation Guideline It can be easily removed with solder wick and other removable material. RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC's liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. Tel : 82-31-250-5011 rfsales@rfhic.com All specifications may change without notice. Version 5.4 9 9 Function Vcc RF OUT E/N |
Price & Availability of RFM0415-10
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |