|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger Rev. 01 -- 11 October 2006 Product data sheet 1. General description The 74HC2G14; 74HCT2G14 is a high-speed Si-gate CMOS device. The 74HC2G14; 74HCT2G14 provides two inverting buffers with Schmitt trigger action which accept standard input signals. They are capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. The inputs switch at different points for positive and negative-going signals. The difference between the positive voltage VT+ and the negative voltage VT- is defined as the input hysteresis voltage VH. 2. Features I I I I Wide supply voltage range from 2.0 V to 6.0 V Complies with JEDEC standard no. 7A High noise immunity ESD protection: N HBM JESD22-A114-D exceeds 2000 V N MM JESD22-A115-A exceeds 200 V Low power dissipation Balanced propagation delays Unlimited input rise and fall times Multiple package options Specified from -40 C to +85 C and -40 C to +125 C I I I I I 3. Applications I Wave and pulse shaper for highly noisy environments I Astable multivibrators I Monostable multivibrators NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 4. Ordering information Table 1. Ordering information Package Temperature range Name 74HC2G14GW 74HC2G14GV 74HCT2G14GW 74HCT2G14GV -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C SC-88 SC-74 SC-88 SC-74 Description plastic surface-mounted package; 6 leads plastic surface-mounted package (TSOP6); 6 leads plastic surface-mounted package; 6 leads plastic surface-mounted package (TSOP6); 6 leads Version SOT363 SOT457 SOT363 SOT457 Type number 5. Marking Table 2. Marking Marking code HK H14 TK T14 Type number 74HC2G14GW 74HC2G14GV 74HCT2G14GW 74HCT2G14GV 6. Functional diagram 1 1A 1Y 6 1 6 1A 1Y 3 2A 2Y 4 3 mnb083 4 2A 2Y mnb084 mnb082 Fig 1. Logic symbol Fig 2. IEC logic symbol Fig 3. Logic diagram 7. Pinning information 7.1 Pinning 74HC2G14 74HCT2G14 1A GND 1 2 6 5 1Y VCC 2Y 2A 3 001aad868 4 Fig 4. Pin configuration 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 2 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 7.2 Pin description Table 3. Symbol 1A GND 2A 2Y VCC 1Y Pin description Pin 1 2 3 4 5 6 Description data input ground (0 V) data input data output supply voltage data output 8. Functional description Table 4. Input nA L H [1] H = HIGH voltage level; L = LOW voltage level. Function table[1] Output nY H L 9. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC IIK IOK IO ICC IGND Tstg Ptot [1] [2] Parameter supply voltage input clamping current output clamping current output current supply current ground current storage temperature total power dissipation Conditions VI < -0.5 V or VI > VCC + 0.5 V VO < -0.5 V or VO > VCC + 0.5 V VO = -0.5 V to VCC + 0.5 V [1] [1] [1] [1] [1] Min -0.5 -65 [2] Max +7.0 20 20 25 +50 -50 +150 250 Unit V mA mA mA mA mA C mW - The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed. For SC-88 and SC-74 packages: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K. 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 3 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 10. Recommended operating conditions Table 6. Symbol VCC VI VO Tamb VCC VI VO Tamb Recommended operating conditions Parameter supply voltage input voltage output voltage ambient temperature supply voltage input voltage output voltage ambient temperature Conditions Min 2.0 0 0 -40 4.5 0 0 -40 Typ 5.0 +25 5.0 +25 Max 6.0 VCC VCC +125 5.5 VCC VCC +125 Unit V V V C V V V C Type 74HC2G14 Type 74HCT2G14 11. Static characteristics Table 7. Static characteristics for 74HC2G14 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Tamb = 25 C VOH HIGH-level output voltage VI = VIH or VIL IO = -20 A; VCC = 2.0 V IO = -20 A; VCC = 4.5 V IO = -20 A; VCC = 6.0 V IO = -4.0 mA; VCC = 4.5 V IO = -5.2 mA; VCC = 6.0 V VOL LOW-level output voltage VI = VIH or VIL IO = 20 A; VCC = 2.0 V IO = 20 A; VCC = 4.5 V IO = 20 A; VCC = 6.0 V IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6.0 V II ICC CI input leakage current supply current input capacitance VI = GND or VCC; VCC = 6.0 V VI = GND or VCC; IO = 0 A; VCC = 6.0 V 2.0 pF 0 0 0 0.15 0.16 0.1 0.1 0.1 0.26 0.26 0.1 1.0 V V V V V A A 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.32 5.81 V V V V V Parameter Conditions Min Typ Max Unit 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 4 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger Table 7. Static characteristics for 74HC2G14 ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VOH Parameter HIGH-level output voltage Conditions VI = VIH or VIL IO = -20 A; VCC = 2.0 V IO = -20 A; VCC = 4.5 V IO = -20 A; VCC = 6.0 V IO = -4.0 mA; VCC = 4.5 V IO = -5.2 mA; VCC = 6.0 V; VOL LOW-level output voltage VI = VIH or VIL IO = 20 A; VCC = 2.0 V IO = 20 A; VCC = 4.5 V IO = 20 A; VCC = 6.0 V IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6.0 V II ICC input leakage current supply current VI = GND or VCC; VCC = 6.0 V VI = GND or VCC; IO = 0 A; VCC = 6.0 V Tamb = -40 C to +125 C VOH HIGH-level output voltage VI = VIH or VIL IO = -20 A; VCC = 2.0 V IO = -20 A; VCC = 4.5 V IO = -20 A; VCC = 6.0 V IO = -4.0 mA; VCC = 4.5 V IO = -5.2 mA; VCC = 6.0 V; VOL LOW-level output voltage VI = VIH or VIL IO = 20 A; VCC = 2.0 V IO = 20 A; VCC = 4.5 V IO = 20 A; VCC = 6.0 V IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6.0 V II ICC input leakage current supply current VI = GND or VCC; VCC = 6.0 V VI = GND or VCC; IO = 0 A; VCC = 6.0 V 0.1 0.1 0.1 0.4 0.4 1.0 20.0 V V V V V A A 1.9 4.4 5.9 3.7 5.2 V V V V V 0.1 0.1 0.1 0.33 0.33 1.0 10.0 V V V V V A A 1.9 4.4 5.9 4.13 5.63 V V V V V Min Typ Max Unit Tamb = -40 C to +85 C 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 5 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger Table 8. Static characteristics for 74HCT2G14 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Tamb = 25 C VOH HIGH-level output voltage VI = VIH or VIL IO = -20 A; VCC = 4.5 V IO = -4.0 mA; VCC = 4.5 V VOL LOW-level output voltage VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V II ICC ICC CI VOH input leakage current supply current additional supply current input capacitance HIGH-level output voltage VI = VIH or VIL IO = -20 A; VCC = 4.5 V IO = -4.0 mA; VCC = 4.5 V VOL LOW-level output voltage VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V II ICC ICC input leakage current supply current additional supply current VI = GND or VCC; VCC = 5.5 V VI = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 2.1 V; VCC = 4.5 V to 5.5 V; IO = 0 A VI = VIH or VIL IO = -20 A; VCC = 4.5 V IO = -4.0 mA; VCC = 4.5 V VOL LOW-level output voltage VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V II ICC ICC input leakage current supply current additional supply current VI = GND or VCC; VCC = 5.5 V VI = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 2.1 V; VCC = 4.5 V to 5.5 V; IO = 0 A 0.1 0.4 1.0 20.0 410 V V A A A 4.4 3.7 V V 0.1 0.33 1.0 10.0 375 V V A A A 4.4 4.13 V V VI = GND or VCC; VCC = 5.5 V VI = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 2.1 V; VCC = 4.5 V to 5.5 V; IO = 0 A 0 0.15 2.0 0.1 0.26 0.1 1.0 300 V V A A A pF 4.4 4.18 4.5 4.32 V V Parameter Conditions Min Typ Max Unit Tamb = -40 C to +85 C Tamb = -40 C to +125 C VOH HIGH-level output voltage 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 6 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 12. Dynamic characteristics Table 9. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 6. Symbol Parameter Conditions Min 74HC2G14 tpd propagation delay nA to nY; see Figure 5 VCC = 2.0 V; CL = 50 pF VCC = 4.5 V; CL = 50 pF VCC = 6.0 V; CL = 50 pF tt transition time nY; see Figure 5 VCC = 2.0 V; CL = 50 pF VCC = 4.5 V; CL = 50 pF VCC = 6.0 V; CL = 50 pF CPD power dissipation capacitance propagation delay transition time power dissipation capacitance tpd is the same as tPLH and tPHL tt is the same as tTLH and tTHL CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi x N + (CL x VCC2 x fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; (CL x VCC2 x fo) = sum of the outputs. [2] [1] 25 C Typ Max -40 C to +125 C Min Max (85 C) Max (125 C) Unit [3] 53 16 13 20 7 5 10 125 25 21 75 15 13 - - 155 31 26 95 19 16 - 190 38 32 110 22 19 - ns ns ns ns ns ns pF VI = GND to VCC - 74HCT2G14 tpd tt CPD nA to nY; see Figure 5 VCC = 4.5 V; CL = 50 pF nY; see Figure 5 VCC = 4.5 V; CL = 50 pF VI = GND to VCC - 1.5 V [3] [2] [1] - 21 6 10 32 15 - - 40 19 - 48 22 - ns ns pF [1] [2] [3] 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 7 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 13. Waveforms VI nA input GND t PHL VOH nY output VOL t THL VM VM 10% VM VM t PLH 90% t TLH mna722 Measurement points are given in Table 10. VOL and VOH are typical voltage output drop that occur with the output load. Fig 5. The data input (nA) to output (nY) propagation delays and output transition times Table 10. Type 74HC2G14 74HCT2G14 Measurement points Input VM 0.5VCC 1.3 V VI GND to VCC GND to 3.0 V tr = tf 6.0 ns 6.0 ns Output VM 0.5VCC 1.3 V VCC VI D.U.T RT CL VO RL = 1 k VCC PULSE GENERATOR open 50 pF mgk563 Test data is given in Table 11. Definitions test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. Fig 6. Load circuitry for switching times Table 11. Type 74HC2G14 74HCT2G14 Test data Input VI GND to VCC GND to 3.0 V tr, tf 6 ns 6 ns Test tPHL, tPLH open open 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 8 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 14. Transfer characteristics Table 12. Transfer characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 6. Symbol Parameter Conditions Min 74HC2G14 VT+ positive-going threshold voltage see Figure 7, Figure 8 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VT- negative-going threshold voltage see Figure 7, Figure 8 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VH hysteresis voltage (VT+ - VT-); see Figure 7, Figure 8 and Figure 9 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V 74HCT2G14 VT+ positive-going threshold voltage see Figure 7 and Figure 8 VCC = 4.5 V VCC = 5.5 V VT- negative-going threshold voltage see Figure 7 and Figure 8 VCC = 4.5 V VCC = 5.5 V VH hysteresis voltage (VT+ - VT-); see Figure 7, Figure 8 and Figure 10 VCC = 4.5 V VCC = 5.5 V 0.40 0.40 0.71 0.67 0.40 0.40 V V 0.50 0.60 0.87 1.11 1.20 1.40 0.50 0.60 1.20 1.40 1.20 1.40 V V 1.20 1.40 1.58 1.78 1.90 2.10 1.20 1.40 1.90 2.10 1.90 2.10 V V 0.30 0.60 0.80 0.60 1.13 1.40 1.00 1.40 1.70 0.30 0.60 0.80 1.00 1.40 1.70 1.00 1.40 1.70 V V V 0.30 1.13 1.50 0.60 1.47 2.06 0.90 2.00 2.60 0.30 1.13 1.50 0.90 2.00 2.60 0.90 2.00 2.60 V V V 1.00 2.30 3.00 1.18 2.60 3.46 1.50 3.15 4.20 1.00 2.30 3.00 1.50 3.15 4.20 1.50 3.15 4.20 V V V 25 C Typ Max -40 C to +125 C Min Max (85 C) Max (125 C) Unit 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 9 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 15. Waveforms transfer characteristics VO VT+ VI VT- VH VH VT- VT+ VI mna207 VO mna208 Fig 7. Transfer characteristic Fig 8. Definition of VT+, VT- and VH 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 10 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 100 ICC (A) mna028 1.0 ICC (mA) 0.8 mna029 0.6 50 0.4 0.2 0 0 1.0 VI (V) 2.0 0 0 2.5 VI (V) 5.0 a. VCC = 2.0 V 1.6 ICC (mA) b. VCC = 4.5 V mna030 0.8 0 0 3.0 VI (V) 6.0 c. VCC = 6.0 V Fig 9. Typical 74HC2G14 transfer characteristics 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 11 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 2.0 ICC (mA) mna031 3.0 ICC (mA) mna032 2.0 1.0 1.0 0 0 2.5 VI (V) 5.0 0 0 3.0 VI (V) 6.0 a. VCC = 4.5 V. Fig 10. Typical 74HCT2G14 transfer characteristics b. VCC = 5.5 V. 16. Application information The slow input rise and fall times cause additional power dissipation, this can be calculated using the following formula: Padd = fi x (tr x ICC(AV) + tf x ICC(AV)) x VCC where: Padd = additional power dissipation (W); fi = input frequency (MHz); tr = input rise time (ns); 10 % to 90 %; tf = input fall time (ns); 90 % to 10 %; ICC(AV) = average additional supply current (A). ICC(AV) differs with positive or negative input transitions, as shown in Figure 11 and Figure 12. An example of a relaxation circuit using the 74HC2G14/74HCT2G14 is shown in Figure 13. 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 12 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 200 ICC(AV) (mA) mna036 150 positive-going edge 100 50 negative-going edge 0 0 2.0 4.0 VCC (V) 6.0 (1) Positive-going edge. (2) Negative-going edge. Fig 11. ICC(AV) as a function of VCC for 74HC2G14; linear change of VI between 0.1VCC to 0.9VCC 200 ICC(AV) (A) 150 mna058 positive-going edge 100 50 negative-going edge 0 0 2 4 VCC (V) 6 (1) Positive-going edge. (2) Negative-going edge. Fig 12. ICC(AV) as a function of VCC for 74HCT2G14; linear change of VI between 0.1VCC to 0.9VCC 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 13 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger R C mna035 For 74HC2G14: f = -- --------------------For 74HCT2G14: f = -- ------------------------ 1 T 1 0.8 x RC 1 T 1 0.67 x RC Fig 13. Relaxation oscillator 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 14 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 17. Package outline Plastic surface-mounted package; 6 leads SOT363 D B E A X y HE vMA 6 5 4 Q pin 1 index A A1 1 e1 e 2 bp 3 wM B detail X Lp c 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.8 A1 max 0.1 bp 0.30 0.20 c 0.25 0.10 D 2.2 1.8 E 1.35 1.15 e 1.3 e1 0.65 HE 2.2 2.0 Lp 0.45 0.15 Q 0.25 0.15 v 0.2 w 0.2 y 0.1 OUTLINE VERSION SOT363 REFERENCES IEC JEDEC JEITA SC-88 EUROPEAN PROJECTION ISSUE DATE 04-11-08 06-03-16 Fig 14. Package outline SOT363 (SC-88) 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 15 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger Plastic surface-mounted package (TSOP6); 6 leads SOT457 D B E A X y HE vMA 6 5 4 Q pin 1 index A A1 c 1 2 3 Lp e bp wM B detail X 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.9 A1 0.1 0.013 bp 0.40 0.25 c 0.26 0.10 D 3.1 2.7 E 1.7 1.3 e 0.95 HE 3.0 2.5 Lp 0.6 0.2 Q 0.33 0.23 v 0.2 w 0.2 y 0.1 OUTLINE VERSION SOT457 REFERENCES IEC JEDEC JEITA SC-74 EUROPEAN PROJECTION ISSUE DATE 05-11-07 06-03-16 Fig 15. Package outline SOT457 (SC-74) 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 16 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 18. Abbreviations Table 13. Acronym CMOS ESD HBM MM DUT Abbreviations Description Complementary Metal Oxide Semiconductor ElectroStatic Discharge Human Body Model Machine Model Device Under Test 19. Revision history Table 14. Revision history Release date 20061011 Data sheet status Product data sheet Change notice Supersedes Document ID 74HC_HCT2G14_1 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 17 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 20. Legal information 20.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 20.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 20.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or 20.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 21. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com 74HC_HCT2G14_1 (c) NXP B.V. 2006. All rights reserved. Product data sheet Rev. 01 -- 11 October 2006 18 of 19 NXP Semiconductors 74HC2G14; 74HCT2G14 Dual inverting Schmitt trigger 22. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 12 13 14 15 16 17 18 19 20 20.1 20.2 20.3 20.4 21 22 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 4 Dynamic characteristics . . . . . . . . . . . . . . . . . . 7 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Transfer characteristics. . . . . . . . . . . . . . . . . . . 9 Waveforms transfer characteristics . . . . . . . . 10 Application information. . . . . . . . . . . . . . . . . . 12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Contact information. . . . . . . . . . . . . . . . . . . . . 18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2006. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 11 October 2006 Document identifier: 74HC_HCT2G14_1 |
Price & Availability of 74HC2G14 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |