![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Features 1.3 GHz Operation Low SSB Phase Noise Floor: -135 dBc/Hz at 100 KHz Offset Differential Input/Single Ended Output Output Buffer Amplifiers 8-Lead SOIC SMT Package Typical Applications This Phase Frequency Detector is a key component in low phase noise frequency synthesis applications such as: * VSAT 10 FREQ. DIVIDER & DETECTORS - SMT * Pt-Pt and Pt-MPt Radios * LMDS * Sonnet Functional Diagram General Description The HMC403S8G is a digital phase-frequency detector intended for use in low noise phaselocked loop applications. Its combination of high frequency of operation along with its low phase noise floor make possible synthesizers with wide loop bandwidth and low N resulting in fast switching and very low phase noise. When used in conjunction with a differential loop amplifier, the HMC403S8G generates an output voltage that can be used to phase lock a VCO to a reference oscillator. The device is available in a small outline 8-lead SOIC plastic package. Electrical Specifications, TA = +25 C, Vcc = 5V Parameter Maximum Input Frequency Minimum Input Frequency Input Power Range Output Voltage Sine Wave Input [1] Fin = 0.1 to 1.3 GHz | ZLoad | 1k @ 100 kHz Offset with 800 MHz Input -10 740 Conditions Min. 1.3 0.1 +10 Typ. Max. Units GHz GHz dBm mV, Pk - Pk dBc/Hz mA SSB Phase Noise Supply Current -135 86 1. Detector will operate down to DC for square-wave input signal. 10 - 66 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Error Voltage vs. Phase Difference, Pin= 0 dBm, T= 25 C * 0.6 250MHz Error Voltage vs. Phase Difference, Pin= 0 dBm, Fin= 800 MHz * 0.6 0.4 +25 C +85 C -40 C 0.4 ERROR VOLTAGE (Vdc) 0.2 0 -0.2 -0.4 -0.6 - -/2 0 /2 PHASE DIFFERENCE (rad) ERROR VOLTAGE (Vdc) 800MHz 1.3GHz 0.2 0 -0.2 -0.4 -0.6 - -/2 0 /2 PHASE DIFFERENCE (rad) 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 67 Test Circuit: * Error Voltage data taken using test circuit above. Loop filter gain has been subtracted from the result. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz SSB Phase Noise Performance, Pin= 0 dBm, T= 25 C 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 2 10 250 MHz 800 MHz 1.3 GHz SSB Phase Noise Performance, Pin= 0 dBm, Fin= 800 MHz 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 2 10 SSB PHASE NOISE (dBc/Hz) 10 FREQ. DIVIDER & DETECTORS - SMT 10 3 10 4 10 5 10 6 SSB PHASE NOISE (dBc/Hz) +25 C +85 C -40 C 10 3 10 4 10 5 10 6 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Supply Current vs. Supply Voltage 100 95 SUPPLY CURRENT (mA) 90 85 80 75 70 65 60 4.75 +25 C +85 C -40 C 5.00 SUPPLY VOLTAGE (Vdc) 5.25 Typical DC Characteristics -40C Symbol Characteristics Min. Icc Power Supply Current Output High Voltage Output Low Voltage 75 Typ. 85 Max. 92 Min. 79 Typ. 86 Max. 92 Min. 79 Typ. 86 Max. 92 mA +25C +85C Unit Voh 1.652 1.867 2.086 1.761 1.981 2.214 1.955 2.19 2.411 V Vol 1.012 1.107 1.286 1.081 1.241 1.414 1.275 1.45 1.631 V 10 - 68 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Absolute Maximum Ratings RF Input (Vcc = +5V) Vcc Surge Current (Pins ND & NU) DC Current (Pins ND & NU) Storage Temperature Operating Temperature +13 dBm +5.5V 4 mA 2 mA -65 to +150 C -40 to +85 C 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 69 Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Pin Description Pin Number Function Description Interface Schematic 10 FREQ. DIVIDER & DETECTORS - SMT 1 R Reference input. 2 NR Reference input complement. 3 V VCO input. 4 NV VCO input complement. 5 GND Ground: Backside of package has exposed metal ground slug which must be connected to ground. 6 ND Down output complement (Device will be permanently damaged if pin is instantaneously shorted to ground. A minimum load impedance magnitude of 1k is required.) 7 NU Up output complement. (Device will be permanently damaged if pin is instantaneously shorted to ground. A minimum load impedance magnitude of 1k is required.) 8 Vcc Supply Voltage. 10 - 70 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Application Circuit 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 71 Note: Pins NU and ND should only be probed with high impedance probes. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Evaluation PCB 10 FREQ. DIVIDER & DETECTORS - SMT List of Materials Item J1 - J4 J5 - J6 C1 C2 - C6 R1 - R2 U1 PCB* Description PC Mount SMA RF Connector DC Pin 4.7 F Capacitor 1000 pF Capacitor, 0402 Pkg. 1000 Ohm Resistor, 0402 Pkg. HMC403S8G 104741 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. * Circuit Board Material: Rogers 4350 10 - 72 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.0703 HMC403S8G HBT DIGITAL PHASE-FREQUENCY DETECTOR, DC - 1.3 GHz Notes: 10 FREQ. DIVIDERS & DETECTORS - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 73 |
Price & Availability of HMC403S8G
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |