![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
TVR2B,TVR2G,TVR2J TOSHIBA Fast Recovery Diode Silicon Diffused Type TVR2B,TVR2G,TVR2J TV Applications (fast recovery) * * * * Average Forward Current: IF (AV) = 0.5 A (Ta = 50C) Repetitive Peak Reverse Voltage: VRRM = 100 to 600 V Reverse Recovery Time: trr = 5 to 20 s Plastic Mold Type. Unit: mm Maximum Ratings (Ta = 25C) Characteristics TVR2B Repetitive peak reverse voltage TVR2G TVR2J TVR2B Reverse voltage (DC) TVR2G TVR2J Average forward current (Ta = 50C) Peak one cycle surge forward current (non repetitive) Junction temperature Storage temperature range IF (AV) IFSM Tj Tstg VR VRRM Symbol Rating 100 400 600 50 300 500 0.5 30 (50 Hz) 33 (60 Hz) -40 to 125 -40 to 125 A A C C V V Unit JEDEC JEITA TOSHIBA DO-41 3-3C1A Weight: 0.3 g (typ.) Electrical Characteristics (Ta = 25C) Characteristics Peak forward voltage Repetitive peak reverse current Reverse recovery time Forward recovery voltage Symbol VFM IRRM trr Vfr Test Condition IFM = 1.0 A VRRM = Rated IF = 20 mA, IR = 1 mA IF = 0.1 A, tr = 100 ns, tw = 5 s Min 5 Typ. Max 1.4 10 20 6 Unit V A s V Note1: Note2: Soldering: 5 mm is the minimum to be kept between case and soldering part. Lead bending: 5 mm is the minimum to be kept from the case when bend the lead wire. Marking Part No. (or abbreviation code) Lot No. A line indicates lead (Pb)-free package or lead (Pb)-free finish. Abbreviation Code VR2B VR2G VR 2J Part No. TVR2B TVR2G TVR2J VR2J 1 2004-08-10 TVR2B,TVR2G,TVR2J Handling Precaution The maximum ratings denote the absolute maximum ratings, which are rated values and must not be exceeded during operation, even for an instant. The following are the general derating methods that we recommend when you design a circuit with a device. VRRM: We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the maximum rating of VRRM for a DC circuit and be no greater than 50% of that of VRRM for an AC circuit. VRRM has a temperature coefficient of 0.1%/C. Take this temperature coefficient into account designing a device at low temperature. We recommend that the worst case current be no greater than 80% of the maximum rating of IF(AV). Carry out adequate heat design. If you can't design a circuit with excellent heat radiation, set the margin by using an allowable Tamax-IF(AV) curve. IF(AV): This rating specifies the non-repetitive peak current in one cycle of a 50-Hz sine wave, condition angle 180. Therefore, this is only applied for an abnormal operation, which seldom occurs during the lifespan of the device. We recommend that a device be used at a Tj of below 100C under the worst load and heat radiation conditions. Thermal resistance between junction and ambient fluctuates depending on the device's mounting condition. When using a device, design a circuit board and a soldering land size to match the appropriate thermal resistance value. Please refer to the Rectifiers databook for further information. 2 2004-08-10 TVR2B,TVR2G,TVR2J Ta max - IF (AV) 200 50 Surge forward current (non-repetitive) (A) Tj = 25C 40 Maximum allowable temperature Ta max (C) 120 Resistive and inductive load 80 Capacitive load 40 Peak surge forward current IFSM 160 30 20 60 Hz 10 50 Hz 0 1 0 0 0.1 0.2 0.3 0.4 0.5 0.6 3 10 30 100 Average forward current IF (AV) (A) Number of cycles 3 2004-08-10 TVR2B,TVR2G,TVR2J RESTRICTIONS ON PRODUCT USE * The information contained herein is subject to change without notice. 030619EAA * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. 4 2004-08-10 |
Price & Availability of TVR2J
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |