|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
SPECIFICATION FOR LCD MODULE Model No. TM122AACW7 Prepared by: Checked by : Verified by : Approved by: Date: Date: Date: Date: TIANMA MICROELECTRONICS CO., LTD Ver 1.0 REVISION RECORD Date Ref. Page Revision No. Revision Items Check & Approval 1/22 Ver 1.0 1 General Specifications: 1.1 Display type: TN 1.2 Display color: Blue-Black Display color*1: Gray Background*2: 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/16 Duty 1/5 Bias 1.6 Backlight: LED 1.7 Controller: S6A0069X01-C0CX(KS0066UP-00CC) 1.8 Display Fonts: 5 x 7 dots+Cursor(1 Character) 1.9 Data Transfer: 8 Bit Parallel 1.10 Operating Temperature: -30----+80 Storage Temperature: -40----+85 1.11 Outline Dimensions: Refer to outline drawing on next page 1.12 Dot Matrix: 12 Characters X 2 Lines 1.13 Dot Size: 0.45X0.60(mm) 1.14 Dot Pitch: 0.55X0.70 (mm) 1.15 Weight: Approx. 30g *1 Color tone is slightly changed by temperature and driving voltage. *2 Color tone will be changed by backlight. 2/22 Ver 1.0 2 Outline Drawing 3/22 Ver 1.0 3 LCD Module Part Numbering System T M 122 A A C W 7 MODIFICATION CODE DESIGNATOR TEMPERATURE RANGE W:WIDE TEMPERATURE RANGE BACKLIGHT TYPE C: TRANSFLECTIVE, LED BACKLIGHT LCD TYPE A: TN/ POSITIVE MODULE SERIES MODULE TYPE 3 DIGITS INDICATING 12 CHARACTERS X 2 LINES T: TIANMA M: MODULE 4/22 Ver 1.0 4 Circuit Block Diagram 5/22 Ver 1.0 5 Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol VDD VSS VLCD TOP Min. -0.3 -0.3 -30 Max. 7.0 V 13.0 +80 Unit Remark No Condensation TST -40 +85 6/22 Ver 1.0 6 Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Symbol Min. Supply Voltage (Logic) Supply Voltage (LCD Drive) High VDD VSS 4.5 Typ. 5.0 Max. 5.5 Unit V VLCD VIH VDD=5.0V VIL VDD=5.0V IDD (VDD-VSS=5.0V) ILED - 7.0 - V Input Signal Voltage 0.7VDD - VDD+0.3 V Low -0.3 - 0.2 VDD V Supply current (Logic) Supply current (LED) - - 1.2 110 mA mA 7/22 Ver 1.0 6.2 Interface Signals Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Symbol Vss/K Vdd V0 RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 A Level 0V 5.0V -5.0V H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L 4.2V Description Ground and Power supply voltage for LED(-) Power supply voltage for logic and LCD(+) Power supply voltage for LCD(-) H:Select data register register Selects read or write H: Read operation Data bit 0 Data bit 1 Data bit 2 Data bit 3 Data bit 4 Data bit 5 Data bit 6 Data bit 7 Power supply voltage for LED(+) L: Write operation Starts data read/write L: Select instruction 8/22 Ver 1.0 6.3 Interface Timing Chart AC Characteristics(VDD=4.5V~5.5V,Ta=-30~+85 ) 9/22 Ver 1.0 10/22 Ver 1.0 6.4 Instruction Code 11/22 Ver 1.0 6.5 Character generator ROM(KS0066U-00) 12/22 Ver 1.0 7 Optical Characteristics 7.1 Optical Characteristics Item Symbol Condition Min. Typ. Ta=25 Max. Unit x y=0 -35 -- 10 Deg Viewing Angle y Cr2 x=0 -30 -- 30 Contrast Ratio Turn on Turn off Cr x =0 y=0 3.0 - - Ton x =0 y=0 - - 150 ms Response Time Toff - - 150 13/22 Ver 1.0 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top Bottom 7.2.2 Definition of Contrast Ratio Bottom Contrast Ratio = B2/B1 = Measuring Conditions: 1) Ambient Temperature: 25 7.2.3 Definition of Response time unselected state brightness selected state brightness ; 2) Frame frequency: 84.3Hz Turn off time: t o f f = t d + t f Turn on time: t o n = t d + t r Measuring Condition: 2) Frame frequency: 84.3Hz 1) Operating Voltage: 7.0V 14/22 Ver 1.0 8 Reliability 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage 3 4 5 6 Content of Test Endurance test applying the high storage temperature for a long time Endurance test applying the low storage temperature for a long time Endurance test applying the High Temperature electric stress (voltage current) 70 Operation and the thermal stress to the 240H element for a long time Endurance test applying the Low Temperature -20 electric stress under low Operation 240H temperature for a long time 90%RH 60 Endurance test applying the high High Temperature temperature and high humidity 240H /Humidity Storage storage for a long time Restore 4H at 25 Endurance test applying the low and high temperature cycle -30 /80 Temperature 25 80 25 -30 10 cycles Cycle 30min 5min 30min 5min (c) Restore 4H at 25 1 cycle Vibration Test (package state) Shock Test (package state) Atmospheric Pressure Test Endurance test applying the vibration during transportation Endurance test applying the shock during transportation Endurance test applying the atmospheric pressure during transportation by air Ta=25 Test condition 80 240H Restore 4H at 25 -30 240H Restore 4H at 25 7 8 9 10Hz~500Hz, 100m/s2, 120min Half- sine wave, 300m/s2, 18ms 25kPa 16H Restore 2H 15/22 Ver 1.0 8.2 Failure Judgment Criterion Criterion Item Basic Specification Electrical specification Mechanical Specification Optical Characteristic Note Remark Test Item No. 123456789 Failure Judgement Criterion Out of the basic Specification Out of the electrical specification Out of the mechanical specification Out of the optical specification For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification 16/22 Ver 1.0 9 QUALITY LEVEL Examination At Ta=25 or Test (unless otherwise stated) Min. Inspection Max. Unit IL AQL Under normal Major External illumi-nation and 1.0 Visual eyesight condition, the See Appendix A II Minor Inspection dis-tance between eyes 2.5 and LCD is 25cm. Under normal Major Display illumi-nation and 1.0 See Appendix B II Defects eyesight condition, Minor display on inspection. 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828 17/22 Ver 1.0 10 Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 18/22 Ver 1.0 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: 40 Temperature : 0 80% Relatively humidity: 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 19/22 Ver 1.0 Appendix A Inspection items and criteria for appearance defects Items Leakage Rainbow Wrong polarizer attachment Polarizer Bubble between polarizer and glass Scratches of polarizer Black spot (in viewing area) Contents Criteria Not permitted According to the limit specimen Not permitted Not counted <0.3mm Max. 3 defects allowed 0.3mm 0.5mm According to the limit specimen Not counted Max. 3 spots allowed X<0.2mm X=(a+b)/2 0.2mm X 0.5mm Max. 3 spots (lines) allowed Black line (in viewing area) Not counted a<0.02mm Max. 3 lines allowed 0.02mm a 0.05mm b 2.0mm Progressive cracks Not permitted 20/22 Ver 1.0 Appendix B Inspection items and criteria for display defects Items Contents Critera Not permitted Not permitted Not permitted According to the limit specimen According to the limit specimen Not counted X<0.1mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Not counted A<0.1mm Max.2 dots allowed 0.1mm A 0.2mm D<0.25mm Max.3 dots allowed 0.1mm X 0.2mm Max.3 dots allowed Open segment or open common Short Wrong viewing angle Contrast radio uneven Crosstalk Not counted Black spot (in viewing area) X<0.1mm X=(a+b)/2 Black line (in viewing area) Not counted a<0.02mm Max.3 spots allowed 0.1mm X 0.2mm Max.3 spots (lines) allowed Max.3 lines allowed 0.02mm a 0.05mm b 0.5mm 21/22 Ver 1.0 Appendix B Inspection items and criteria for display defects (continued) Items Content Critera Not counted x 0.1mm Max. 2 defects allowed 0.1mm x 0.2mm x=(a+b)/2 Not counted a 0.1mm Max. 1 defects allowed 0.1mm a 0.2mm D>0 Max.3 defects allowed Transformation of segment Max.2 defects allowed 0.8W a 1.2W a=measured value of width W=nominal value of width 22/22 Ver 1.0 |
Price & Availability of TM122AACW7 | |
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |