![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Si91822 New Product Vishay Siliconix Micropower 300-mA CMOS LDO Regulator With Error Flag/Power-On-Reset FEATURES Low 150-mV Dropout at 300-mA Load Guaranteed 300-mA Output Current 600-mA Peak Output Current Capability Uses Low ESR Ceramic Output Capacitor Fast Load and Line Transient Response Only 100-mV(rms) Noise With Noise Bypass Capacitor D 1-mA Maximum Shutdown Current D Built-in Short Circuit and Thermal Protection D Out-Of-Regulation Error Flag (Power Good or POR) D D D D D D D Fixed1.215-V, 1.5-V, 1.8-V, 2.0-V, 2.5-V, 2.8-V, 3.0-V, 3.3-V, 5.0-V, or Adjustable Output Voltage Options D Other Output Voltages Available by Special Order APPLICATIONS D Cellular Phones D Laptop and Palm Computers D PDA, Digital Still Cameras DESCRIPTION The Si91822 is a 300-mA CMOS LDO (low dropout) voltage regulator. The device features ultra low ground current and dropout voltage to prolong battery life in portable electronics. The Si91822 offers line/load transient response and ripple rejection superior to that of bipolar or BiCMOS LDO regulators. The device is designed to maintain regulation while delivering 600-mA peak current. This is useful for systems that have high surge current upon turn-on. The Si91822 is designed to drive the lower cost ceramic, as well as tantalum, output capacitors. The device is guaranteed stable from maximum load current down to 0-mA load. In addition, an external noise bypass capacitor connected to the device's CNOISE pin will lower the LDO's output noise for low noise applications. The Si91822 also includes an out-of-regulation error flag. When the output voltage is 5% below its nominal output voltage, the error flag output goes low. If a capacitor is connected to the device's delay pin, the error flag output pin will generate a delayed power-on-reset signal. TYPICAL APPLICATIONS CIRCUITS 1 2 3 4 CNOISE DELAY GND VIN SD ERROR SENSE/ADJ VOUT 8 7 6 5 2.2 mF 1 2 3 4 CNOISE DELAY GND VIN SD ERROR 8 7 6 5 VOUT VIN 2.2 mF GND SENSE/ADJ VOUT VIN 2.2 mF GND VOUT 2.2 mF Si91822 Si91822 FIGURE 1. Fixed Output 1 2 0.1 mF 3 4 CNOISE DELAY GND VIN SD ERROR SENSE/ADJ VOUT 8 7 6 5 FIGURE 2. Adjustable Output ON/OFF POR 1 MW VOUT 0.1 mF VIN 2.2 mF GND Si91822 2.2 mF FIGURE 3. Low Noise, Full Features Application Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 1 Si91822 Vishay Siliconix ABSOLUTE MAXIMUM RATINGS Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 V SD Input Voltage, VSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VIN Output Current, IOUT . . . . . . . . 300 mA Continuous, Short Circuit Protected Output Voltage, VOUT . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VO(nom) + 0.3 V Maximum Junction Temperature, TJ(max) . . . . . . . . . . . . . . . . . . . . . . . 150_C Storage Temperature, TSTG . . . . . . . . . . . . . . . . . . . . . . . . . . -55_C to 150_C ESD (Human Body Model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV Power Dissipation (Package)b 8-Pin MSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 846 mW Thermal Impedance (QJA) 8-Pin MSOPa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130_C/W Notes a. Device mounted with all leads soldered or welded to PC board. b. Derate 7.7 mW/_C above TA = 25_C New Product Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 V to 6 V Output Voltage, VOUT (Adjustable Version) . . . . . . . . . . . . . . . 1.215 V to 5 V SD Input Voltage, VSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to VIN CIN = 2.2 mF, COUT = 2.2 mF (ceramic, X5R or X7R type) , CNOISE = 0.1 mF (ceramic) COUT Range = 1 mF to 10 mF ("10%, x5R or x7R type) CIN w COUT Operating Ambient Temperature, TA . . . . . . . . . . . . . . . . . . . . -40_C to 85_C Operating Junction Temperature, TJ . . . . . . . . . . . . . . . . . . . -40_C to 135_C SPECIFICATIONS Test Conditions Unless Otherwise Specified Parameter Symbol VIN = VOUT(nom) + 1 V, IOUT = 1 mA CIN = 2.2 mF, COUT = 2.2 mF, VSD = 1.5 V Limits -40 to 85_C Tempa Minb Typc Maxb Unit Output Voltage Range Output Voltage Accuracy (Fixed Versions) Feedback Voltage (ADJ Version) VOUT Adjustable Version 1 mA v IOUT v 300 mA Full Room Full Room 1.215 -1.5 -2.5 1.191 1.179 1.215 5 1.5 2.5 1.239 1.251 V % VO(nom) VADJ Full From VIN = VOUT + 1 V to VOUT + 2 V V Line Regulation (VADJ v VOUT v 4 V) DVOUT Line Regulation (4 V v VOUT v 5 V) V IN 100 VOUT Full -0.18 0.18 %/V From VIN = 5.5 V to 6 V IOUT = 10 mA Full -0.18 0.18 Room Room Room 5 85 150 20 180 350 500 mV Dropout Voltaged (@VOUT(nom) w 2 V) VIN - VOUT Dropout Voltaged (@VOUT(nom) t 2 V, VIN w 2 V) IOUT = 200 mA IOUT = 300 mA IOUT = 200 mA IOUT = 300 mA IOUT = 0 mA IOUT = 200 mA Full Room Room Full Room Room 150 1000 170 290 250 375 525 Ground Pin Current IGND Full Room 1500 1500 m mA IOUT = 300 mA Full 2800 Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 2 Si91822 New Product SPECIFICATIONS Test Conditions Unless Otherwise Specified Parameter Symbol VIN = VOUT(nom) + 1 V, IOUT = 1 mA CIN = 2.2 mF, COUT = 2.2 mF, VSD = 1.5 V Vishay Siliconix Limits -40 to 85_C Tempa Minb Typc Maxa Unit mA nA mA Shutdown Supply Current ADJ Pin Current Peak Output Current Output Noise Voltage IIN(off) IADJ IO(peak) eN VSD = 0 V ADJ = 1.2 V VOUT w 0.95 x VOUT(nom), tpw = 2 ms BW = 50 Hz to 100 kHz IOUT = 150 mA w/o CNOISE CNOISE = 0.1 mF f = 1 kHz Room Room Room Room Room Room Room Room Room Room Room Room 600 0.1 5 1 100 200 100 60 60 40 10 mV m (rms) Ripple Rejection DVOUT/DVIN IOUT = 150 mA f = 10 kHz f = 100 kHz dB Dynamic Line Regulation Dynamic Load Regulation VOUT Turn-On-Time DVO(line) DVO(load) tON VIN : VOUT(nom) + 1 V to VOUT(nom) + 2 V tR/tF = 5 ms, IOUT = 300 mA IOUT : 1 mA to 150 mA, tR/tF = 2 ms VIN = 4.3 V VOUT = 3.3 V w/o CNOISE Cap CNOISE = 0.1 mF mV 30 5 2 ms mS Thermal Shutdown Thermal Shutdown Junction Temp Thermal Hysteresis Short Circuit Current tJ(s/d) tHYST ISC VOUT = 0 V Room Room Room 165 20 800 _C _ mA Shutdown Input VIH SD Input Voltage VIL IIH IIL VHYST High = Regulator ON (Rising) Low = Regulator OFF (Falling) VSD = 0 V, Regulator OFF VSD = 6 V, Regulator ON Full Full Room Room Full 0.01 1.0 100 1.5 VIN 0.4 V SD Input Currente Shutdown Hysteresis mA m mV Error Output Output High Leakage Output Low Voltageg Out-of-Regulation Error Flag Threshold Voltageg Hysteresis g Delay Pin Current Source IOFF VOL VTH VHYST IDELAY ERROR = VOUT(nom) ISINK = 2 mA Full Full Full Room Room 1.2 0.93 x VOUT 0.95 x VOUT 2% x VOUT 2.2 3.0 mA 0.01 2 0.4 0.97 x VOUT V mA Notes a. Room = 25_C, Full = -40 to 85_C. b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Typical values for dropout voltage at VOUT w 2 V are measured at VOUT = 3.3 V, while typical values for dropout voltage at VOUT < 2 V are measured at VOUT = 1.8 V. d. Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the output voltage measured with a 1-V differential, provided that VIN does not not drop below 2.0 V. When VOUT(nom) is less than 2.0 V, the output will be in regulation when 2.0 V - VOUT(nom) is greater than the dropout voltage specified. e. The device's shutdown pin includes a typical 6-MW internal pull-down resistor connected to ground. f. VOUT is defined as the output voltage of the DUT at 1 mA. g. The Error Output (Low) function is guaranteed for VIN w2.0 V. Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 3 Si91822 Vishay Siliconix TIMING WAVEFORMS New Product VIN tON VNOM 0.95 VNOM VOUT ERROR tDELAY FIGURE 4. Timing Diagram for Power-Up PIN CONFIGURATION MSOP-8 CNOISE DELAY GND VIN 1 2 3 4 8 7 6 5 SD ERROR SENSE or ADJ VOUT Top View PIN DESCRIPTION Pin Number 1 2 3 4 5 6 7 8 Name CNOISE DELAY GND VIN VOUT SENSE or ADJ ERROR SD Function Noise bypass pin. For low noise applications, a 0.01-mF or larger ceramic capacitor should be connected from this pin to ground. Capacitor connected from this pin to ground will allow a delayed power-on-reset signal at the ERROR (Pin 7) output. Refer to Figure 4. Ground pin. Local ground for CNOISE and COUT. Input supply pin. Bypass this pin with a 2.2-mF ceramic or tantalum capacitor to ground. Output voltage. Connect COUT between this pin and ground. For fixed output voltage versions, this pin should be connected to VOUT (Pin 5). For adjustable output voltage version, this voltage feedback pin sets the output voltage via an external resistor divider. This open drain output is an error flag output which goes low when VOUT drops 5% below its nominal voltage. This pin also provides a power-on-reset signal if a capacitor is connected to the DELAY pin. By applying less than 0.4 V to this pin, the device will be turned off. Connect this pin to VIN if unused. Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 4 Si91822 New Product ORDERING INFORMATION Part Number SI91822DH-12-T1 Si91822DH-15-T1 Si91822DH-18-T1 Si91822DH-20-T1 Si91822DH-25-T1 Si91822DH-28-T1 Si91822DH-30-T1 Si91822DH-33-T1 Si91822DH-50-T1 Si91822DH-AD-T1 Vishay Siliconix Marking 1822 1215 1822 1500 1822 1800 1822 2000 1822 2500 1822 2800 1822 3000 1822 3300 1822 5000 Voltage 1.215 V 1.50 V 1.80 V 2.00 V 2.50 V Temperature Package Eval Kit -40 to 85_C _ Si91822DB MSOP-8 Temperature Range -40 to 85_C Board Type Surface Mount 2.80 V 3.00 V 3.30 V 5.00 V 1822 Adjustable ADJ Additional voltage options are available. TYPICAL CHARACTERISTICS (INTERNALLY REGULATED, 25_C UNLESS NOTED) Dropout Voltage vs. Load Current 300 VOUT = 3.3 V 3.5 3.0 RLOAD = 16.5 W 2.5 V DROP (mV) 200 V OUT (V) 2.0 1.5 1.0 50 0.5 0.0 0 100 200 300 ILOAD (mA) 400 500 600 0 1 2 3 VIN (V) 4 5 6 Dropout Characteristic 250 150 100 0 Dropout Voltage vs. Temperature 200 175 150 V DROP (mV) 125 100 75 50 50 25 0 -50 IOUT = 10 mA IOUT = 0 mA -25 0 25 50 75 100 Junction Temperature (_C) 125 150 0 1.0 VOUT = 3.3 V IOUT = 350 mA 250 IOUT = 300 mA Dropout Voltage (mV) 200 300 Dropout Voltage vs. VOUT IOUT = 350 mA 150 IOUT = 300 mA 100 IOUT = 10 mA 1.5 2.0 2.5 3.0 VOUT 3.5 4.0 4.5 5.0 Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 5 Si91822 Vishay Siliconix New Product TYPICAL CHARACTERISTICS (INTERNALLY REGULATED, 25_C UNLESS NOTED) Normalized Output Voltage vs. Load Current 0.30 0.15 0.00 -0.4 -0.15 -0.30 -0.45 -0.60 -0.75 0 50 100 150 200 250 300 350 400 Load Current (mA) -1.0 V OUT (%) -0.0 IOUT = 0 mA -0.2 IOUT = 100 mA Normalized VOUT vs. Temperature Output Voltage (%) -0.6 IOUT = 200 mA -0.8 IOUT = 300 mA IOUT = 350 mA -1.2 -40 -20 0 20 40 60 80 100 120 140 Junction Temperature (_C) GND Current vs. Load Current 0.0 VOUT = 5 V -0.3 250 300 No Load GND Pin Current vs. Input Voltage 200 I GND ( mA) I GND ( mA) -0.6 25_C -0.9 85_C 150 25_C 100 -1.2 -40_C 50 -1.5 0 50 100 150 200 250 300 350 Load Current (mA) 0 0 1 2 3 4 5 6 7 Input Voltage (V) Power Supply Rejection 0 CIN = 10 mF COUT = 2.2 mF ILOAD = 150 mA -20 I GND ( mA) 2000 GND Pin Current vs. Temperature and Load VOUT = 5 V IOUT = 350 mA 1500 Gain (dB) IOUT = 200 mA 1000 -40 -60 500 IOUT = 0 mA -80 10 100 1000 10000 100000 1000000 Frequency (Hz) 0 -40 -20 0 20 40 60 80 100 120 140 Junction Temperature (_C) www.vishay.com 6 Document Number: 71671 S-04932--Rev. A, 15-Oct-01 Si91822 New Product TYPICAL WAVEFORMS Load Transient Response-1 Load Transient Response-2 Vishay Siliconix VOUT 10 mV/div VOUT 10 mV/div ILOAD 100 mA/div ILOAD 100 mA/div 5.00 ms/div VOUT = 3.3 V COUT = 2.2 mF ILOAD = 1 to 150 mA trise = 2 msec 5.00 ms/div VOUT = 3.3 V COUT = 2.2 mF ILOAD = 150 to 1 mA tfall = 2 msec Load Transient Response-3 Load Transient Response-4 VOUT 10 mV/div VOUT 10 mV/div ILOAD 100 mA/div ILOAD 100 mA/div 5.00 ms/div VOUT = 3.3 V COUT = 1.0 mF ILOAD = 1 to 150 mA trise = 2 msec 5.00 ms/div VOUT = 3.3 V COUT = 1.0 mF ILOAD = 150 to 1 mA tfall = 2 msec LineTransient Response-1 VOUT 1 V/div VIN 2 V/div LineTransient Respons-2 VOUT 10 mV/div VOUT 10 mV/div 5.00 ms/div VINSTEP = 4.3 to 5.3 V VOUT = 3.3 V COUT = 2.2 mF CIN = 10 mF ILOAD = 350 mA trise = 5 msec 5.00 ms/div VINSTEP = 5.3 to 4.3 V VOUT = 3.3 V COUT = 2.2 mF CIN = 10 mF ILOAD = 350 mA tfall = 5 msec Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 7 Si91822 Vishay Siliconix TYPICAL WAVEFORMS Turn-On Sequence Turn-Off Sequence New Product VIN CH-3 2 V/div VIN 2 V/div VOUT 2 V/div VOUT CH-1 2 V/div Cdelay 2 V/div ERROR 2 V/div Cdelay CH-4 2 V/div ERROR CH-2 2 V/div VIN = 4.2 V VOUT = 3.3 V Cdelay = 0.1 mF CNOISE = 0.1 mF ILOAD = 350 mA 5.00 ms/div VIN = 4.2 V VOUT = 3.3 V Cdelay = 0.1 mF CNOISE = 0.1 mF ILOAD = 350 mA 10.00 ms/div Output Noise 10.0 Noise Spectrum mV 500 mV/div Hz 0.01 1 ms/div VIN = 4.2 V VOUT = 3.3 V IOUT = 150 mA CNOISE = 0.1 mF BW = 10 Hz to 1 MHz 100 Hz VIN = 4.1 V VOUT = 3.3 V/10 mA CNOISE = 0.1 mF 1 MHz www.vishay.com 8 Document Number: 71671 S-04932--Rev. A, 15-Oct-01 Si91822 New Product BLOCK DIAGRAMS Vishay Siliconix Switches shown for device in normal operating mode (SD = HIGH) 6 VIN CIN 2.2 mF 4 SENSE 1 CNOISE 8 SD ON RFB2 OFF 6 MW RFB1 + + - + - 60 mV 2 mA 2 CDELAY 0.1 mF ERROR + 3 GND 1.215 V VREF - - + 7 To VIN 5 COUT 2.2 mF REXT VOUT FIGURE 5. 300-mA CMOS LDO Regulator (Fixed Output) 6 VIN CIN 2.2 mF 4 ADJ 1 CNOISE R2 VADJ 8 SD ON OFF 6 MW 60 mV + + - + - 2 mA 2 CDELAY 0.1 mF ERROR + 3 GND 1.215 V VREF - - + 7 To VIN 5 COUT 2.2 mF REXT VOUT R1 FIGURE 6. 300-mA CMOS LDO Regulator (Adjustable Output) Document Number: 71671 S-04932--Rev. A, 15-Oct-01 www.vishay.com 9 Si91822 Vishay Siliconix DETAILED DESCRIPTION The Si91822 is a low drop out, low quiescent current, and very linear regulator family with very fast transient response. It is primarily designed for battery powered applications where battery run time is at a premium. The low quiescent current allows extended standby time while low drop out voltage enables the system to fully utilize battery power before recharge. The Si91822 is a very fast regulator with bandwidth exceeding 50 kHz while maintaining low quiescent current at light load conditions. With this bandwidth, the Si91822 is the fastest LDO available today. The Si91822 is stable with any output capacitor type from 1 mF to 10.0 mF. However, X5R or X7R ceramic capacitors are recommended for best output noise and transient performance. VIN VIN is the input supply pin. The bypass capacitor for this pin is not critical as long as the input supply has low enough source impedance. For practical circuits, a 1.0-mF or larger ceramic capacitor is recommended. When the source impedance is not low enough and/or the source is several inches from the Si91822, then a larger input bypass capacitor is needed. It is required that the equivalent impedance (source impedance, wire, and trace impedance in parallel with input bypass capacitor impedance) must be smaller than the input impedance of the Si91822 for stable operation. When the source impedance, wire, and trace impedance are unknown, it is recommended that an input bypass capacitor be used of a value that is equal to or greater than the output capacitor. VOUT VOUT is the output voltage of the regulator. Connect a bypass capacitor from VOUT to ground. The output capacitor can be any value from 1.0 mF to 10.0 mF. A ceramic capacitor with X5R or X7R dielectric type is recommended for best output noise, line transient, and load transient performance. GND Ground is the common ground connection for VIN and VOUT. It is also the local ground connection for CNOISE, DELAY, SENSE or ADJ, and SD. SENSE or ADJ SENSE is used to sense the output voltage. Connect SENSE to VOUT for the fixed voltage version. For the adjustable output version, use a resistor divider R1 and R2, connect R1 from VOUT to ADJ and R2 from ADJ to ground. R2 should be in the 25-kW to 150-kW range for low power consumption, while maintaining adequate noise immunity. www.vishay.com New Product The formula below calculates the value of R1, given the desired output voltage and the R2 value, V OUT * VADJ R2 VADJ (1) R1 + VADJ is nominally 1.215 V. SHUTDOWN (SD) SD controls the turning on and off of the Si91822. VOUT is guaranteed to be on when the SD pin voltage equals or is greater than 1.5 V. VOUT is guaranteed to be off when theSD pin voltage equals or is less than 0.4 V. During shutdown mode, the Si91822 will draw less than 2-mA current from the source. To automatically turn on VOUT whenever the input is applied, tie the SD pin to VIN. ERROR ERROR is an open drain output that goes low when VOUT is less than 5% of its normal value. As with any open drain output, an external pull up resistor is needed. When a capacitor is connected from DELAY to GROUND, the error signal transition from low to high is delayed (see Delay section). This delayed error signal can be used as the power-on reset signal for the application system. (Refer to Figure 4.) The ERROR pin is disconnected if not used. DELAY A capacitor from DELAY to GROUND sets the time delay for ERROR going from low to high state. The time delay can be calculated using the following formula: Tdelay + VADJ Cdelay Idelay (2) The DELAY pin should be an open circuit if not used. CNOISE For low noise application, connect a high frequency ceramic capacitor from CNOISE to ground. A 0.01-mF or a 0.1-mF X5R or X7R is recommended. Document Number: 71671 S-04932--Rev. A, 15-Oct-01 10 |
Price & Availability of SI91822DH-12-T1
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |