![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
WAN PLL IDT82V3280 Version 2 June 19, 2006 6024 Silver Creek Valley Road, San Jose, CA 95138 Telephone: (800) 345-7015 * TWX: 910-338-2070 * FAX: (408) 284-2775 Printed in U.S.A. (c) 2006 Integrated Device Technology, Inc. DISCLAIMER Integrated Device Technology, Inc. reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. IDT does not assume any responsibility for use of any circuitry described other than the circuitry embodied in an IDT product. The Company makes no representations that circuitry described herein is free from patent infringement or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent, patent rights or other rights, of Integrated Device Technology, Inc. LIFE SUPPORT POLICY Integrated Device Technology's products are not authorized for use as critical components in life support devices or systems unless a specific written agreement pertaining to such intended use is executed between the manufacturer and an officer of IDT. 1. Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any components of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Table of Contents FEATURES .............................................................................................................................................................................. 9 HIGHLIGHTS.................................................................................................................................................................................................... 9 MAIN FEATURES ............................................................................................................................................................................................ 9 OTHER FEATURES ......................................................................................................................................................................................... 9 APPLICATIONS....................................................................................................................................................................... 9 DESCRIPTION....................................................................................................................................................................... 10 FUNCTIONAL BLOCK DIAGRAM ........................................................................................................................................ 11 1 PIN ASSIGNMENT ........................................................................................................................................................... 12 2 PIN DESCRIPTION .......................................................................................................................................................... 13 3 FUNCTIONAL DESCRIPTION ......................................................................................................................................... 19 RESET ........................................................................................................................................................................................................... 19 MASTER CLOCK .......................................................................................................................................................................................... 19 INPUT CLOCKS & FRAME SYNC SIGNAL ................................................................................................................................................. 20 3.3.1 Input Clocks .................................................................................................................................................................................... 20 3.3.2 Frame SYNC Input Signals ............................................................................................................................................................ 20 3.4 INPUT CLOCK PRE-DIVIDER ...................................................................................................................................................................... 21 3.5 INPUT CLOCK QUALITY MONITORING ..................................................................................................................................................... 23 3.5.1 LOS Monitoring .............................................................................................................................................................................. 23 3.5.2 Activity Monitoring ......................................................................................................................................................................... 23 3.5.3 Frequency Monitoring ................................................................................................................................................................... 24 3.6 T0 / T4 DPLL INPUT CLOCK SELECTION .................................................................................................................................................. 25 3.6.1 External Fast Selection (T0 only) .................................................................................................................................................. 25 3.6.2 Forced Selection ............................................................................................................................................................................ 26 3.6.3 Automatic Selection ....................................................................................................................................................................... 26 3.7 SELECTED INPUT CLOCK MONITORING .................................................................................................................................................. 27 3.7.1 T0 / T4 DPLL Locking Detection ................................................................................................................................................... 27 3.7.1.1 Fast Loss .......................................................................................................................................................................... 27 3.7.1.2 Coarse Phase Loss .......................................................................................................................................................... 27 3.7.1.3 Fine Phase Loss ............................................................................................................................................................... 27 3.7.1.4 Hard Limit Exceeding ....................................................................................................................................................... 27 3.7.2 Locking Status ............................................................................................................................................................................... 27 3.7.3 Phase Lock Alarm (T0 only) .......................................................................................................................................................... 28 3.8 SELECTED INPUT CLOCK SWITCH ........................................................................................................................................................... 29 3.8.1 Input Clock Validity ........................................................................................................................................................................ 29 3.8.2 Selected Input Clock Switch ......................................................................................................................................................... 29 3.8.2.1 Revertive Switch ............................................................................................................................................................... 29 3.8.2.2 Non-Revertive Switch (T0 only) ........................................................................................................................................ 30 3.8.3 Selected / Qualified Input Clocks Indication ................................................................................................................................ 30 3.9 SELECTED INPUT CLOCK STATUS VS. DPLL OPERATING MODE ....................................................................................................... 31 3.9.1 T0 Selected Input Clock vs. DPLL Operating Mode .................................................................................................................... 31 3.9.2 T4 Selected Input Clock vs. DPLL Operating Mode .................................................................................................................... 33 3.10 T0 / T4 DPLL OPERATING MODE ............................................................................................................................................................... 34 3.10.1 T0 DPLL Operating Mode .............................................................................................................................................................. 34 3.10.1.1 Free-Run Mode ................................................................................................................................................................ 34 3.10.1.2 Pre-Locked Mode ............................................................................................................................................................. 34 3.10.1.3 Locked Mode .................................................................................................................................................................... 34 3.1 3.2 3.3 Table of Contents 3 June 19, 2006 IDT82V3280 WAN PLL 3.11 3.12 3.13 3.14 3.15 3.16 3.17 4.1 5.1 5.2 5.3 5.4 5.5 3.10.1.3.1 Temp-Holdover Mode .................................................................................................................................... 34 3.10.1.4 Lost-Phase Mode ............................................................................................................................................................. 34 3.10.1.5 Holdover Mode ................................................................................................................................................................. 34 3.10.1.5.1 Automatic Instantaneous ............................................................................................................................... 35 3.10.1.5.2 Automatic Slow Averaged ............................................................................................................................. 35 3.10.1.5.3 Automatic Fast Averaged .............................................................................................................................. 35 3.10.1.5.4 Manual ........................................................................................................................................................... 35 3.10.1.5.5 Holdover Frequency Offset Read .................................................................................................................. 35 3.10.1.6 Pre-Locked2 Mode ........................................................................................................................................................... 35 3.10.2 T4 DPLL Operating Mode .............................................................................................................................................................. 35 3.10.2.1 Free-Run Mode ................................................................................................................................................................ 35 3.10.2.2 Locked Mode .................................................................................................................................................................... 35 3.10.2.3 Holdover Mode ................................................................................................................................................................. 35 T0 / T4 DPLL OUTPUT ................................................................................................................................................................................. 37 3.11.1 PFD Output Limit ............................................................................................................................................................................ 37 3.11.2 Frequency Offset Limit .................................................................................................................................................................. 37 3.11.3 PBO (T0 only) ................................................................................................................................................................................. 37 3.11.4 Phase Offset Selection (T0 only) .................................................................................................................................................. 37 3.11.5 Four Paths of T0 / T4 DPLL Outputs ............................................................................................................................................. 37 3.11.5.1 T0 Path ............................................................................................................................................................................. 37 3.11.5.2 T4 Path ............................................................................................................................................................................. 38 T0 / T4 APLL ................................................................................................................................................................................................. 39 OUTPUT CLOCKS & FRAME SYNC SIGNALS ........................................................................................................................................... 39 3.13.1 Output Clocks ................................................................................................................................................................................. 39 3.13.2 Frame SYNC Output Signals ......................................................................................................................................................... 42 MASTER / SLAVE CONFIGURATION ......................................................................................................................................................... 44 INTERRUPT SUMMARY ............................................................................................................................................................................... 45 T0 AND T4 SUMMARY ................................................................................................................................................................................. 45 POWER SUPPLY FILTERING TECHNIQUES ............................................................................................................................................. 46 MASTER / SLAVE APPLICATION ............................................................................................................................................................... 47 4 TYPICAL APPLICATION ................................................................................................................................................. 47 5 MICROPROCESSOR INTERFACE .................................................................................................................................. 48 EPROM MODE .............................................................................................................................................................................................. 49 MULTIPLEXED MODE .................................................................................................................................................................................. 50 INTEL MODE ................................................................................................................................................................................................. 52 MOTOROLA MODE ...................................................................................................................................................................................... 54 SERIAL MODE .............................................................................................................................................................................................. 56 6 JTAG ................................................................................................................................................................................ 58 7 PROGRAMMING INFORMATION .................................................................................................................................... 59 7.1 7.2 REGISTER MAP ............................................................................................................................................................................................ 59 REGISTER DESCRIPTION ........................................................................................................................................................................... 65 7.2.1 Global Control Registers ............................................................................................................................................................... 65 7.2.2 Interrupt Registers ......................................................................................................................................................................... 74 7.2.3 Input Clock Frequency & Priority Configuration Registers ....................................................................................................... 79 7.2.4 Input Clock Quality Monitoring Configuration & Status Registers ......................................................................................... 102 7.2.5 T0 / T4 DPLL Input Clock Selection Registers ........................................................................................................................... 116 7.2.6 T0 / T4 DPLL State Machine Control Registers ......................................................................................................................... 120 7.2.7 T0 / T4 DPLL & APLL Configuration Registers .......................................................................................................................... 122 7.2.8 Output Configuration Registers .................................................................................................................................................. 136 7.2.9 PBO & Phase Offset Control Registers ...................................................................................................................................... 146 7.2.10 Synchronization Configuration Registers ................................................................................................................................. 148 JUNCTION TEMPERATURE ...................................................................................................................................................................... 149 8 THERMAL MANAGEMENT ........................................................................................................................................... 149 8.1 Table of Contents 4 June 19, 2006 IDT82V3280 WAN PLL 9 ELECTRICAL SPECIFICATIONS .................................................................................................................................. 150 9.1 9.2 9.3 8.2 8.3 EXAMPLE OF JUNCTION TEMPERATURE CALCULATION ................................................................................................................... 149 HEATSINK EVALUATION .......................................................................................................................................................................... 149 9.4 9.5 9.6 9.7 ABSOLUTE MAXIMUM RATING ................................................................................................................................................................ 150 RECOMMENDED OPERATION CONDITIONS .......................................................................................................................................... 150 I/O SPECIFICATIONS ................................................................................................................................................................................. 151 9.3.1 AMI Input / Output Port ................................................................................................................................................................ 151 9.3.1.1 Structure ......................................................................................................................................................................... 151 9.3.1.2 I/O Level ......................................................................................................................................................................... 151 9.3.1.3 Over-Voltage Protection ................................................................................................................................................. 153 9.3.2 CMOS Input / Output Port ............................................................................................................................................................ 153 9.3.3 PECL / LVDS Input / Output Port ................................................................................................................................................ 154 9.3.3.1 PECL Input / Output Port ................................................................................................................................................ 154 9.3.3.2 LVDS Input / Output Port ................................................................................................................................................ 156 JITTER & WANDER PERFORMANCE ....................................................................................................................................................... 157 OUTPUT WANDER GENERATION ............................................................................................................................................................ 160 INPUT / OUTPUT CLOCK TIMING ............................................................................................................................................................. 161 OUTPUT CLOCK TIMING ........................................................................................................................................................................... 162 ORDERING INFORMATION .......................................................................................................................................... 167 Table of Contents 5 June 19, 2006 List of Tables Table 1: Table 2: Table 3: Table 4: Table 5: Table 6: Table 7: Table 8: Table 9: Table 10: Table 11: Table 12: Table 13: Table 14: Table 15: Table 16: Table 17: Table 18: Table 19: Table 20: Table 21: Table 22: Table 23: Table 24: Table 25: Table 26: Table 27: Table 28: Table 29: Table 30: Table 31: Table 32: Table 33: Table 34: Table 35: Table 36: Table 37: Table 38: Table 39: Table 40: Table 41: Table 42: Table 43: Table 44: Table 45: Table 46: Table 47: Table 48: Pin Description ............................................................................................................................................................................................. 13 Related Bit / Register in Chapter 3.2 ........................................................................................................................................................... 19 Related Bit / Register in Chapter 3.3 ........................................................................................................................................................... 20 Related Bit / Register in Chapter 3.4 ........................................................................................................................................................... 22 Related Bit / Register in Chapter 3.5 ........................................................................................................................................................... 24 Input Clock Selection for T0 Path ................................................................................................................................................................ 25 Input Clock Selection for T4 Path ................................................................................................................................................................ 25 External Fast Selection ................................................................................................................................................................................ 25 Related Bit / Register in Chapter 3.6 ........................................................................................................................................................... 26 Coarse Phase Limit Programming (the selected input clock of 2 kHz, 4 kHz or 8 kHz) .............................................................................. 27 Coarse Phase Limit Programming (the selected input clock of other than 2 kHz, 4 kHz and 8 kHz) .......................................................... 27 Related Bit / Register in Chapter 3.7 ........................................................................................................................................................... 28 Conditions of Qualified Input Clocks Available for T0 & T4 Selection ......................................................................................................... 29 Related Bit / Register in Chapter 3.8 ........................................................................................................................................................... 30 T0 DPLL Operating Mode Control ............................................................................................................................................................... 31 T4 DPLL Operating Mode Control ............................................................................................................................................................... 33 Related Bit / Register in Chapter 3.9 ........................................................................................................................................................... 33 Frequency Offset Control in Temp-Holdover Mode ..................................................................................................................................... 34 Frequency Offset Control in Holdover Mode ............................................................................................................................................... 35 Holdover Frequency Offset Read ................................................................................................................................................................ 35 Related Bit / Register in Chapter 3.10 ......................................................................................................................................................... 36 Related Bit / Register in Chapter 3.11 ......................................................................................................................................................... 38 Related Bit / Register in Chapter 3.12 ......................................................................................................................................................... 39 Outputs on OUT1 ~ OUT7 if Derived from T0/T4 DPLL Outputs ................................................................................................................ 40 Outputs on OUT1 ~ OUT7 if Derived from T0/T4 APLL .............................................................................................................................. 41 Outputs on OUT8 & OUT9 ........................................................................................................................................................................... 41 Synchronization Control ............................................................................................................................................................................... 42 Related Bit / Register in Chapter 3.13 ......................................................................................................................................................... 43 Device Master / Slave Control ..................................................................................................................................................................... 44 Related Bit / Register in Chapter 3.15 ......................................................................................................................................................... 45 Microprocessor Interface ............................................................................................................................................................................. 48 Access Timing Characteristics in EPROM Mode ......................................................................................................................................... 49 Read Timing Characteristics in Multiplexed Mode ....................................................................................................................................... 50 Write Timing Characteristics in Multiplexed Mode ....................................................................................................................................... 51 Read Timing Characteristics in Intel Mode .................................................................................................................................................. 52 Write Timing Characteristics in Intel Mode .................................................................................................................................................. 53 Read Timing Characteristics in Motorola Mode ........................................................................................................................................... 54 Write Timing Characteristics in Motorola Mode ........................................................................................................................................... 55 Read Timing Characteristics in Serial Mode ................................................................................................................................................ 56 Write Timing Characteristics in Serial Mode ................................................................................................................................................ 57 JTAG Timing Characteristics ....................................................................................................................................................................... 58 Register List and Map .................................................................................................................................................................................. 59 Power Consumption and Maximum Junction Temperature ....................................................................................................................... 149 Thermal Data ............................................................................................................................................................................................. 149 Absolute Maximum Rating ......................................................................................................................................................................... 150 Recommended Operation Conditions ........................................................................................................................................................ 150 AMI Input / Output Port Electrical Characteristics ...................................................................................................................................... 152 CMOS Input Port Electrical Characteristics ............................................................................................................................................... 153 List of Tables 6 June 19, 2006 IDT82V3280 WAN PLL Table 49: Table 50: Table 51: Table 52: Table 53: Table 54: Table 55: Table 56: Table 57: Table 58: Table 59: Table 60: Table 61: Table 62: Table 63: CMOS Input Port with Internal Pull-Up Resistor Electrical Characteristics ................................................................................................ CMOS Input Port with Internal Pull-Down Resistor Electrical Characteristics ........................................................................................... CMOS Output Port Electrical Characteristics ............................................................................................................................................ PECL Input / Output Port Electrical Characteristics ................................................................................................................................... LVDS Input / Output Port Electrical Characteristics ................................................................................................................................... Output Clock Jitter Generation .................................................................................................................................................................. Output Clock Phase Noise ......................................................................................................................................................................... Input Jitter Tolerance (155.52 MHz) .......................................................................................................................................................... Input Jitter Tolerance (1.544 MHz) ............................................................................................................................................................ Input Jitter Tolerance (2.048 MHz) ............................................................................................................................................................ Input Jitter Tolerance (8 kHz) .................................................................................................................................................................... T0 DPLL Jitter Transfer & Damping Factor ............................................................................................................................................... T4 DPLL Jitter Transfer & Damping Factor ............................................................................................................................................... Input/Output Clock Timing 3 ...................................................................................................................................................................... Output Clock Timing .................................................................................................................................................................................. 153 153 153 155 156 157 158 158 158 158 158 159 159 161 162 List of Tables 7 June 19, 2006 List of Figures Figure 1. Functional Block Diagram ............................................................................................................................................................................ 11 Figure 2. Pin Assignment (Top View) .......................................................................................................................................................................... 12 Figure 3. Pre-Divider for An Input Clock ..................................................................................................................................................................... 21 Figure 4. Input Clock Activity Monitoring ..................................................................................................................................................................... 23 Figure 5. External Fast Selection ................................................................................................................................................................................ 25 Figure 6. Qualified Input Clocks for Automatic Selection ............................................................................................................................................ 26 Figure 7. T0 Selected Input Clock vs. DPLL Automatic Operating Mode ................................................................................................................... 32 Figure 8. T4 Selected Input Clock vs. DPLL Automatic Operating Mode ................................................................................................................... 33 Figure 9. On Target Frame Sync Input Signal Timing ................................................................................................................................................. 42 Figure 10. 0.5 UI Early Frame Sync Input Signal Timing ............................................................................................................................................. 42 Figure 11. 0.5 UI Late Frame Sync Input Signal Timing .............................................................................................................................................. 43 Figure 12. 1 UI Late Frame Sync Input Signal Timing ................................................................................................................................................. 43 Figure 13. Physical Connection Between Two Devices .............................................................................................................................................. 44 Figure 14. IDT82V3280 Power Decoupling Scheme ................................................................................................................................................... 46 Figure 15. Typical Application ...................................................................................................................................................................................... 47 Figure 16. EPROM Access Timing Diagram ............................................................................................................................................................... 49 Figure 17. Multiplexed Read Timing Diagram ............................................................................................................................................................. 50 Figure 18. Multiplexed Write Timing Diagram .............................................................................................................................................................. 51 Figure 19. Intel Read Timing Diagram ......................................................................................................................................................................... 52 Figure 20. Intel Write Timing Diagram ......................................................................................................................................................................... 53 Figure 21. Motorola Read Timing Diagram .................................................................................................................................................................. 54 Figure 22. Motorola Write Timing Diagram .................................................................................................................................................................. 55 Figure 23. Serial Read Timing Diagram (CLKE Asserted Low) ................................................................................................................................... 56 Figure 24. Serial Read Timing Diagram (CLKE Asserted High) .................................................................................................................................. 56 Figure 25. Serial Write Timing Diagram ....................................................................................................................................................................... 57 Figure 26. JTAG Interface Timing Diagram ................................................................................................................................................................. 58 Figure 27. 64 kHz + 8 kHz Signal Structure .............................................................................................................................................................. 151 Figure 28. 64 kHz + 8 kHz + 0.4 kHz Signal Structure .............................................................................................................................................. 151 Figure 29. 64 kHz + 8 kHz / 64 kHz + 8 kHz + 0.4 kHz Signal Input Level ................................................................................................................ 151 Figure 30. 64 kHz + 8 kHz / 64 kHz + 8 kHz + 0.4 kHz Signal Output Level ............................................................................................................. 151 Figure 31. AMI Input / Output Port Line Termination (Recommended) ..................................................................................................................... 152 Figure 32. Recommended PECL Input Port Line Termination .................................................................................................................................. 154 Figure 33. Recommended PECL Output Port Line Termination ................................................................................................................................ 154 Figure 34. Recommended LVDS Input Port Line Termination .................................................................................................................................. 156 Figure 35. Recommended LVDS Output Port Line Termination ................................................................................................................................ 156 Figure 36. Output Wander Generation ...................................................................................................................................................................... 160 Figure 37. Input / Output Clock Timing ...................................................................................................................................................................... 161 List of Figures 8 June 19, 2006 WAN PLL IDT82V3280 FEATURES HIGHLIGHTS * The first single PLL chip: * Features 0.5 mHz to 560 Hz bandwidth * Exceeds GR-253-CORE (OC-12) and ITU-T G.813 (STM-16/ Option I) jitter generation requirements * Provides node clocks for Cellular and WLL base-station (GSM and 3G networks) * Provides clocks for DSL access concentrators (DSLAM), especially for Japan TCM-ISDN network timing based ADSL equipments Provides an integrated single-chip solution for Synchronous Equipment Timing Source, including Stratum 2, 3E, 3, SMC, 4E and 4 clocks Employs DPLL and APLL to feature excellent jitter performance and minimize the number of the external components Integrates T0 DPLL and T4 DPLL; T4 DPLL locks independently or locks to T0 DPLL Supports Forced or Automatic operating mode switch controlled by an internal state machine; the primary operating modes are FreeRun, Locked and Holdover Supports programmable DPLL bandwidth (0.5 mHz to 560 Hz in 19 steps) and damping factor (1.2 to 20 in 5 steps) Supports 1.1X10-5 ppm absolute holdover accuracy and 4.4X10-8 ppm instantaneous holdover accuracy Supports PBO to minimize phase transients on T0 DPLL output to be no more than 0.61 ns Supports phase absorption when phase-time changes on T0 selected input clock are greater than a programmable limit over an interval of less than 0.1 seconds Supports programmable input-to-output phase offset adjustment Limits the phase and frequency offset of the outputs Supports manual and automatic selected input clock switch * * * * * * * * * * MAIN FEATURES * * * * * * * * * * * Supports automatic hitless selected input clock switch on clock failure Supports three types of input clock sources: recovered clock from STM-N or OC-n, PDH network synchronization timing and external synchronization reference timing Provides a 2 kHz, 4 kHz or 8 kHz frame sync input signal, and a 2 kHz and an 8 kHz frame sync output signals Provides 14 input clocks whose frequency cover from 2 kHz to 622.08 MHz Provides 9 output clocks whose frequency cover from 1 Hz to 622.08 MHz Provides output clocks for BITS, GPS, 3G, GSM, etc. Supports AMI, PECL/LVDS and CMOS input/output technologies Supports master clock calibration Supports Master/Slave application (two chips used together) to enable system protection against single chip failure Meets Telcordia GR-1244-CORE, GR-253-CORE, GR-1377CORE, ITU-T G.812, ITU-T G.813 and ITU-T G.783 criteria Multiple microprocessor interface modes: EPROM, Multiplexed, Intel, Motorola and Serial IEEE 1149.1 JTAG Boundary Scan Single 3.3 V operation with 5 V tolerant CMOS I/Os 100-pin TQFP package, Green package options available BITS / SSU SMC / SEC (SONET / SDH) DWDM cross-connect and transmission equipments Central Office Timing Source and Distribution Core and access IP switches / routers Gigabit and Terabit IP switches / routers IP and ATM core switches and access equipments Cellular and WLL base-station node clocks Broadband and multi-service access equipments Any other telecom equipments that need synchronous equipment system timing OTHER FEATURES * * * * * * * * * * * * * * APPLICATIONS IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. 9 2006 Integrated Device Technology, Inc. June 19, 2006 DSC-6772/2 IDT82V3280 WAN PLL DESCRIPTION The IDT82V3280 is an integrated, single-chip solution for the Synchronous Equipment Timing Source for Stratum 2, 3E, 3, SMC, 4E and 4 clocks in SONET / SDH equipments, DWDM and Wireless base station, such as GSM, 3G, DSL concentrator, Router and Access Network applications. The device supports three types of input clock sources: recovered clock from STM-N or OC-n, PDH network synchronization timing and external synchronization reference timing. Based on ITU-T G.783 and Telcordia GR-253-CORE, the device consists of T0 and T4 paths. The T0 path is a high quality and highly configurable path to provide system clock for node timing synchronization within a SONET / SDH network. The T4 path is simpler and less configurable for equipment synchronization. The T4 path locks independently from the T0 path or locks to the T0 path. An input clock is automatically or manually selected for T0 and T4 each for DPLL locking. Both the T0 and T4 paths support three primary operating modes: Free-Run, Locked and Holdover. In Free-Run mode, the DPLL refers to the master clock. In Locked mode, the DPLL locks to the selected input clock. In Holdover mode, the DPLL resorts to the fre- quency data acquired in Locked mode. Whatever the operating mode is, the DPLL gives a stable performance without being affected by operating conditions or silicon process variations. If the DPLL outputs are processed by T0/T4 APLL, the outputs of the device will be in a better jitter/wander performance. The device provides programmable DPLL bandwidths: 0.5 mHz to 560 Hz in 19 steps and damping factors: 1.2 to 20 in 5 steps. Different settings cover all SONET / SDH clock synchronization requirements. A high stable input is required for the master clock in different applications. The master clock is used as a reference clock for all the internal circuits in the device. It can be calibrated within 741 ppm. All the read/write registers are accessed through a microprocessor interface. The device supports five microprocessor interface modes: EPROM, Multiplexed, Intel, Motorola and Serial. In general, the device can be used in Master/Slave application. In this application, two devices should be used together to enable system protection against single chip failure. See Chapter 4 Typical Application for details. Description 10 June 19, 2006 IDT82V3280 10 OUT1 MUX Divider OUT1 T4 DPLL 77.76 MHz Divider 10 OUT2 MUX OUT2 GSM/GPS/16E1/16T1 Functional Block Diagram 10 T4 Input Selector MUX T4 PFD & LPF 16E1/16T1 OUT3 MUX Divider OUT3 Input 10 OUT4 MUX Priority Priority Priority Priority Priority Priority Priority Priority Priority Priority Priority Priority Priority Divider 12E1/24T1/E3/T3 Divider OUT4 Input Pre-Divider IN1 IN2 Input Pre-Divider Input Pre-Divider Input Pre-Divider Input Pre-Divider 10 T0 77.76 MHz Monitors T0 8 kHz 8 k Divider T4 APLL IN3 IN4 IN5 IN6 T4 APLL MUX Input Pre-Divider OUT5 MUX Divider OUT5 FUNCTIONAL BLOCK DIAGRAM Input Pre-Divider IN7 IN8 Input Pre-Divider Input Pre-Divider 10 77.76 MHz Input Pre-Divider Input Pre-Divider OUT6 MUX Divider OUT6 Input Pre-Divider Figure 1. Functional Block Diagram 11 GSM/OBSAI/16E1/16T1 Priority Selection IN9 IN10 IN11 IN12 IN13 T0 APLL MUX Input Pre-Divider T0 APLL 10 OUT7 MUX Divider IN14 PBO Phase Offset T0 Input Selector T0 PFD & LPF 12E1/24T1/E3/T3 16E1/16T1 Input Pre-Divider OUT7 EX_SYNC1 From T0 77.76 MHz From T4 77.76 MHz OUT8 MUX Auto Divider OUT8 Divider From T0 16E1/16T1 T0 DPLL From T4 16E1/16T1 OUT9 MUX Auto Divider OUT9 Auto Divider Auto Divider FRSYNC_8K MFRSYNC_2K Output APLL Microprocessor Interface JTAG June 19, 2006 OSCI WAN PLL IDT82V3280 WAN PLL 1 PIN ASSIGNMENT SONET/SDH MS/SL IC7 IC6 IC5 OUT9 OUT5 OUT4 AGND3 VDDA3 OUT3 OUT2 OUT1 DGND7 VDDD7 VDDD6 DGND6 AD0/SDO AD1 AD2 AD3 AD4 AD5 AD6 AD7 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 41 42 43 44 45 46 47 48 49 28 29 30 31 32 33 34 35 36 37 38 39 40 50 AGND TRST IC1 IC2 AGND1 VDDA1 TMS INT_REQ TCK OSCI DGND1 VDDD1 VDDD3 DGND3 DGND2 VDDD2 IC3 FF_SRCSW VDDA2 AGND2 TDO IC4 TDI IN1 IN2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 IDT82V3280 RDY RST ALE/SCLK RD WR CS A0/SDI A1/CLKE A2 A3 A4 A5 A6 DGND5 VDDD5 MPU_MODE0 MPU_MODE1 MPU_MODE2 IN14 IN13 IN12 IN11 IN10 IN9 IN8 Pin Assignment VDD_AMI OUT8_NEG OUT8_POS GND_AMI FRSYNC_8K MFRSYNC_2K GND_DIFF1 VDD_DIFF1 OUT6_POS OUT6_NEG OUT7_POS OUT7_NEG GND_DIFF2 VDD_DIFF2 IN5_POS IN5_NEG IN6_POS IN6_NEG NC EX_SYNC1 IN3 IN4 IN7 DGND4 VDDD4 Figure 2. Pin Assignment (Top View) 12 June 19, 2006 IDT82V3280 WAN PLL 2 Name PIN DESCRIPTION Pin No. I/O Type Global Control Signal OSCI 10 I CMOS OSCI: Crystal Oscillator Master Clock A nominal 12.8000 MHz clock provided by a crystal oscillator is input on this pin. It is the master clock for the device. FF_SRCSW: External Fast Selection Enable During reset, this pin determines the default value of the EXT_SW bit (b4, 0BH) 2. The EXT_SW bit determines whether the External Fast Selection is enabled. High: The default value of the EXT_SW bit (b4, 0BH) is `1' (External Fast selection is enabled); Low: The default value of the EXT_SW bit (b4, 0BH) is `0' (External Fast selection is disabled). After reset, this pin selects an input clock pair for the T0 DPLL if the External Fast selection is enabled: High: Pair IN3 / IN5 is selected. Low: Pair IN4 / IN6 is selected. After reset, the input on this pin takes no effect if the External Fast selection is disabled. MS/SL: Master / Slave Selection This pin, together with the MS_SL_CTRL bit (b0, 13H), controls whether the device is configured as the Master or as the Slave. Refer to Chapter 3.14 Master / Slave Configuration for details. The signal level on this pin is reflected by the MASTER_SLAVE bit (b1, 09H). SONET/SDH: SONET / SDH Frequency Selection During reset, this pin determines the default value of the IN_SONET_SDH bit (b2, 09H): High: The default value of the IN_SONET_SDH bit is `1' (SONET); Low: The default value of the IN_SONET_SDH bit is `0' (SDH). After reset, the value on this pin takes no effect. RST: Reset A low pulse of at least 50 s on this pin resets the device. After this pin is high, the device will still be held in reset state for 500 ms (typical). EX_SYNC1: External Sync Input 1 A 2 kHz, 4 kHz or 8 kHz signal is input on this pin. Input Clock IN1 IN2 IN3 24 25 46 IN1: Input Clock 1 I AMI A 64 kHz + 8 kHz or 64 kHz + 8 kHz + 0.4 kHz composite clock is input on this pin. IN2: Input Clock 2 I AMI A 64 kHz + 8 kHz or 64 kHz + 8 kHz + 0.4 kHz composite clock is input on this pin. IN3: Input Clock 3 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN4: Input Clock 4 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN5_POS / IN5_NEG: Positive / Negative Input Clock 5 A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, I PECL/LVDS 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz clock is differentially input on this pair of pins. Whether the clock signal is PECL or LVDS is automatically detected. Description 1 Table 1: Pin Description FF_SRCSW 18 I pull-down CMOS MS/SL 99 I pull-up CMOS SONET/SDH 100 I pull-down CMOS RST 74 I pull-up CMOS Frame Synchronization Input Signal EX_SYNC1 45 I pull-down CMOS IN4 47 IN5_POS IN5_NEG 40 41 Pin Description 13 June 19, 2006 IDT82V3280 WAN PLL Table 1: Pin Description (Continued) Name IN6_POS IN6_NEG Pin No. 42 43 I/O Type Description 1 IN7 48 IN8 51 IN9 52 IN10 53 IN11 54 IN12 55 IN13 56 IN14 57 IN6_POS / IN6_NEG: Positive / Negative Input Clock 6 A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, I PECL/LVDS 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz clock is differentially input on this pair of pins. Whether the clock signal is PECL or LVDS is automatically detected. IN7: Input Clock 7 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN8: Input Clock 8 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN9: Input Clock 9 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN10: Input Clock 10 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN11: Input Clock 11 A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, I CMOS 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. pull-down In Slave operation, the frequency of the T0 selected input clock IN11 is recommended to be 6.48 MHz. IN12: Input Clock 12 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN13: Input Clock 13 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. IN14: Input Clock 14 I CMOS A 2 kHz, 4 kHz, N x 8 kHz 3, 1.544 MHz (SONET) / 2.048 MHz (SDH), 6.48 MHz, 19.44 MHz, pull-down 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is input on this pin. Output Frame Synchronization Signal FRSYNC_8K: 8 kHz Frame Sync Output An 8 kHz signal is output on this pin. MFRSYNC_2K: 2 kHz Multiframe Sync Output A 2 kHz signal is output on this pin. Output Clock OUT1: Output Clock 1 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is output on this pin. OUT2: Output Clock 2 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is output on this pin. OUT3: Output Clock 3 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is output on this pin. FRSYNC_8K MFRSYNC_2K 30 31 O O CMOS CMOS OUT1 88 O CMOS OUT2 89 O CMOS OUT3 90 O CMOS Pin Description 14 June 19, 2006 IDT82V3280 WAN PLL Table 1: Pin Description (Continued) Name Pin No. I/O Type Description 1 OUT4 93 O OUT5 94 O OUT6_POS OUT6_NEG 34 O 35 OUT7_POS OUT7_NEG OUT8_POS OUT8_NEG OUT9 36 O 37 28 O 27 95 O OUT4: Output Clock 4 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, CMOS 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is output on this pin. OUT5: Output Clock 5 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, CMOS 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz or 155.52 MHz clock is output on this pin. OUT6_POS / OUT6_NEG: Positive / Negative Output Clock 6 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, PECL/LVDS 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz clock is differentially output on this pair of pins. OUT7_POS / OUT7_NEG: Positive / Negative Output Clock 7 A 1 Hz, 400 Hz, 2 kHz, 8 kHz, 64 kHz, N x E1 4, N x T1 5, N x 13.0 MHz 6, N x 3.84 MHz 7, PECL/LVDS 5 MHz, 10 MHz, 20 MHz, E3, T3, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz or 622.08 MHz clock is differentially output on this pair of pins. OUT8_POS / OUT8_NEG: Positive / Negative Output Clock 8 A 64 kHz + 8 kHz or 64 kHz + 8 kHz + 0.4 kHz composite clock is differentially output on this AMI pair of pins. CMOS OUT9: Output Clock 9 A 1.544 MHz (SONET) / 2.048 MHz (SDH) BITS/SSU clock is output on this pin. Microprocessor Interface CS: Chip Selection A transition from high to low must occur on this pin for each read or write operation and this pin should remain low until the operation is over. INT_REQ: Interrupt Request This pin is used as an interrupt request. The output characteristics are determined by the HZ_EN bit (b1, 0CH) and the INT_POL bit (b0, 0CH). MPU_MODE[2:0]: Microprocessor Interface Mode Selection The device supports five microprocessor interface modes: EPROM, Multiplexed, Intel, Motorola and Serial. During reset, these pins determine the default value of the MPU_SEL_CNFG[2:0] bits (b2~0, 7FH) as follows: 001 (EPROM mode); 010 (Multiplexed mode); 011 (Intel mode); 100 (Motorola mode); 101 (Serial mode); 110 - 111 (Reserved). After reset, these pins are general purpose inputs. The microprocessor interface mode is selected by the MPU_SEL_CNFG[2:0] bits (b2~0, 7FH). The value of these pins is always reflected by the MPU_PIN_STS[2:0] bits (b2~0, 02H). CS 70 I pull-up O CMOS INT_REQ 8 CMOS MPU_MODE0 MPU_MODE1 MPU_MODE2 60 59 58 I pull-down CMOS Pin Description 15 June 19, 2006 IDT82V3280 WAN PLL Table 1: Pin Description (Continued) Name A0 / SDI A1 / CLKE A2 A3 A4 A5 A6 AD0 / SDO AD1 AD2 AD3 AD4 AD5 AD6 AD7 Pin No. 69 68 67 66 65 64 63 83 82 81 80 79 78 77 76 I pull-up WR: Write Operation In Multiplexed and Intel modes, this pin is asserted low to initiate a write operation. In Motorola mode, this pin is asserted low to initiate a write operation or s asserted high to initiate a read operation. In EPROM and Serial modes, this pin should be connected to ground. RD: Read Operation In Multiplexed and Intel modes, this pin is asserted low to initiate a read operation. In EPROM, Motorola and Serial modes, this pin should be connected to ground. ALE: Address Latch Enable In Multiplexed mode, the address on AD[7:0] pins is sampled into the device on the falling edge of ALE. SCLK: Shift Clock In Serial mode, a shift clock is input on this pin. Data on SDI is sampled by the device on the rising edge of SCLK. Data on SDO is updated on the active edge of SCLK. The active edge is determined by the CLKE. In EPROM, Intel and Motorola modes, this pin should be connected to ground. I/O pull-down I pull-down CMOS CLKE: SCLK Active Edge Selection In Serial mode, this pin selects the active edge of SCLK to update the SDO: High - The falling edge; Low - The rising edge. In Multiplexed mode, A0/SDI, A1/CLKE and A[6:2] pins should be connected to ground. In Serial mode, A[6:2] pins should be connected to ground. AD[7:0]: Address / Data Bus In EPROM, Intel and Motorola modes, these pins are the bi-directional data bus of the microprocessor interface. In Multiplexed mode, these pins are the bi-directional address/data bus of the microprocessor interface. SDO: Serial Data Output In Serial mode, this pin is used as the serial data output. Data on this pin is serially clocked out of the device on the active edge of SCLK. In Serial mode, AD[7:1] pins should be connected to ground. I/O Type Description 1 A[6:0]: Address Bus In ERPOM, Intel and Motorola modes, these pins are the address bus of the microprocessor interface. SDI: Serial Data Input In Serial mode, this pin is used as the serial data input. Address and data on this pin are serially clocked into the device on the rising edge of SCLK. CMOS WR 71 CMOS RD 72 I pull-up CMOS ALE / SCLK 73 I pull-down CMOS Pin Description 16 June 19, 2006 IDT82V3280 WAN PLL Table 1: Pin Description (Continued) Name Pin No. I/O Type Description 1 RDY: Ready/Data Acknowledge In Multiplexed and Intel modes, a high level on this pin indicates that a read/write cycle is completed. A low level on this pin indicates that wait state must be inserted. In Motorola mode, a low level on this pin indicates that valid information on the data bus is ready for a read operation or acknowledges the acceptance of the written data during a write operation. In EPROM and Serial modes, this pin should be connected to ground. JTAG (per IEEE 1149.1) TRST 2 I pull-down I pull-up CMOS TRST: JTAG Test Reset (Active Low) A low signal on this pin resets the JTAG test port. This pin should be connected to ground when JTAG is not used. TMS: JTAG Test Mode Select The signal on this pin controls the JTAG test performance and is sampled on the rising edge of TCK. TCK: JTAG Test Clock The clock for the JTAG test is input on this pin. TDI and TMS are sampled on the rising edge of TCK and TDO is updated on the falling edge of TCK. If TCK is idle at a low level, all stored-state devices contained in the test logic will indefinitely retain their state. TDI: JTAG Test Data Input The test data is input on this pin. It is clocked into the device on the rising edge of TCK. TDO: JTAG Test Data Output The test data is output on this pin. It is clocked out of the device on the falling edge of TCK. TDO pin outputs a high impedance signal except during the process of data scanning. This pin can indicate the interrupt of T0 selected input clock fail, as determined by the LOS_FLAG_ON_TDO bit (b6, 0BH). Refer to Chapter 3.8.1 Input Clock Validity for details. Power & Ground VDDD1 VDDD2 VDDD3 VDDD4 VDDD5 VDDD6 VDDD7 VDDA1 VDDA2 VDDA3 VDD_AMI VDD_DIFF1 VDD_DIFF2 12 16 13 50 61 85 86 6 19 91 26 33 39 Power Power VDDDn: 3.3 V Digital Power Supply Each VDDDn should be paralleled with ground through a 0.1 F capacitor. RDY 75 O CMOS TMS 7 CMOS TCK 9 I pull-down I pull-up CMOS TDI 23 CMOS TDO 21 O CMOS VDDAn: 3.3 V Analog Power Supply Each VDDAn should be paralleled with ground through a 0.1 F capacitor. Power Power Power - VDD_AMI: 3.3 V Power Supply for AMI I/O VDD_DIFF1: 3.3 V Power Supply for OUT6 VDD_DIFF2: 3.3 V Power Supply for OUT7 Pin Description 17 June 19, 2006 IDT82V3280 WAN PLL Table 1: Pin Description (Continued) Name DGND1 DGND2 DGND3 DGND4 DGND5 DGND6 DGND7 AGND1 AGND2 AGND3 GND_DIFF1 GND_DIFF2 GND_AMI AGND IC1 IC2 IC3 IC4 IC5 IC6 IC7 NC Pin No. 11 15 14 49 62 84 87 5 20 92 32 38 29 1 3 4 17 22 96 97 98 44 Ground Ground I/O Type DGNDn: Digital Ground Description 1 AGNDn: Analog Ground Ground Ground Ground Ground - GND_DIFF: Ground for OUT6 GND_DIFF: Ground for OUT7 GND_AMI: Ground for AMI I/O AGND: Analog Ground Others IC: Internal Connected Internal Use. These pins should be left open for normal operation. - - NC: Not Connected Note: 1. All the unused input pins should be connected to ground; the output of all the unused output pins are don't-care. 2. The contents in the brackets indicate the position of the register bit/bits. 3. N x 8 kHz: 1 < N < 19440. 4. N x E1: N = 1, 2, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64. 5. N x T1: N = 1, 2, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96. 6. N x 13.0 MHz: N = 1, 2, 4. 7. N x 3.84 MHz: N = 1, 2, 4, 8, 16, 10, 20, 40. Pin Description 18 June 19, 2006 IDT82V3280 WAN PLL 3 3.1 FUNCTIONAL DESCRIPTION RESET 3.2 MASTER CLOCK The reset operation resets all registers and state machines to their default value or status. After power on, the device must be reset for normal operation. For a complete reset, the RST pin must be asserted low for at least 50 s. After the RST pin is pulled high, the device will still be in reset state for 500 ms (typical). If the RST pin is held low continuously, the device remains in reset state. A nominal 12.8000 MHz clock, provided by a crystal oscillator, is input on the OSCI pin. This clock is provided for the device as a master clock. The master clock is used as a reference clock for all the internal circuits. A better active edge of the master clock is selected by the OSC_EDGE bit to improve jitter and wander performance. In fact, an offset from the nominal frequency may input on the OSCI pin. This offset can be compensated by setting the NOMINAL_FREQ_VALUE[23:0] bits. The calibration range is within 741 ppm. The performance of the master clock should meet GR-1244-CORE, GR-253-CORE, ITU-T G.812 and G.813 criteria. Table 2: Related Bit / Register in Chapter 3.2 Bit NOMINAL_FREQ_VALUE[23:0] OSC_EDGE Register NOMINAL_FREQ[23:16]_CNFG, NOMINAL_FREQ[15:8]_CNFG, NOMINAL_FREQ[7:0]_CNFG DIFFERENTIAL_IN_OUT_OSCI_CNFG Address (Hex) 06, 05, 04 0A Functional Description 19 June 19, 2006 IDT82V3280 WAN PLL 3.3 3.3.1 INPUT CLOCKS & FRAME SYNC SIGNAL INPUT CLOCKS Altogether 14 clocks and 1 frame sync signal are input to the device. The device provides 14 input clock ports. According to the input port technology, the input ports support the following technologies: * AMI * PECL/LVDS * CMOS According to the input clock source, the following clock sources are supported: * T1: Recovered clock from STM-N or OC-n * T2: PDH network synchronization timing * T3: External synchronization reference timing IN1 and IN2 support the AMI input signal only and the clock source is from T3. The input clock is a 64 kHz + 8 kHz or 64 kHz + 8 kHz + 0.4 kHz composite clock. The 400HZ_SEL bit should be set to match the input frequency. Any input violation that does not meet the standard composite clock structure will induce an AMI violation. The AMI violation is indicated by the AMI1_VIOL 1 / AMI2_VIOL 1 bit. If the AMI1_VIOL 2 / AMI2_VIOL 2 bit is `1', the occurrence of an AMI violation will trigger an interrupt. IN3, IN4 and IN7 ~ IN14 support CMOS input signal only and the clock sources can be from T1, T2 or T3. IN5 and IN6 support PECL/LVDS input signal only and automatically detect whether the signal is PECL or LVDS. The clock sources can be from T1, T2 or T3. For SDH and SONET networks, the default frequency is different. SONET / SDH frequency selection is controlled by the IN_SONET_SDH bit. During reset, the default value of the IN_SONET_SDH bit is determined by the SONET/SDH pin: high for SONET and low for SDH. After reset, the input signal on the SONET/SDH pin takes no effect. 3.3.2 FRAME SYNC INPUT SIGNALS A 2 kHz, 4 kHz or 8 kHz frame sync signal is input on the EX_SYNC1 pin. It is a CMOS input. The input frequency should match the setting in the SYNC_FREQ[1:0] bits. The frame sync input signal is used for frame sync output signal synchronization. Refer to Chapter 3.13.2 Frame SYNC Output Signals for details. Table 3: Related Bit / Register in Chapter 3.3 Bit 400HZ_SEL AMI1_VIOL 1 AMI2_VIOL 1 AMI1_VIOL 2 AMI2_VIOL 2 IN_SONET_SDH SYNC_FREQ[1:0] Register IN1_CNFG IN2_CNFG INTERRUPT3_STS INTERRUPTS3_ENABLE_CNFG INPUT_MODE_CNFG Address (Hex) 14 15 0F 12 09 Functional Description 20 June 19, 2006 IDT82V3280 WAN PLL 3.4 INPUT CLOCK PRE-DIVIDER Each input clock is assigned an internal Pre-Divider. The Pre-Divider is used to divide the clock frequency down to the DPLL required frequency, which is no more than 38.88 MHz. For IN1 and IN2, the DPLL required frequency is fixed to 8 kHz (i.e., the corresponding IN_FREQ[3:0] bits are `0000'). The 8 kHz clock is extracted from the composite clock and the Pre-Divider is bypassed automatically. For IN3 ~ IN14, the DPLL required frequency is set by the corresponding IN_FREQ[3:0] bits. If the input clock is of 2 kHz, 4 kHz or 8 kHz, the Pre-Divider is bypassed automatically and the corresponding IN_FREQ[3:0] bits should be set to match the input frequency; the input clock can be inverted, as determined by the IN_2K_4K_8K_INV bit. Each Pre-Divider consists of a HF (High Frequency) Divider (only available for IN5 and IN6), a DivN Divider and a Lock 8k Divider, as shown in Figure 3. The HF Divider, which is only available for IN5 and IN6, should be used when the input clock is higher than (>) 155.52 MHz. The input clock can be divided by 4, 5 or can bypass the HF Divider, as determined by the IN5_DIV[1:0]/IN6_DIV[1:0] bits correspondingly. Either the DivN Divider or the Lock 8k Divider can be used or both can be bypassed, as determined by the DIRECT_DIV bit and the LOCK_8K bit. When the DivN Divider is used for INn (3 n 14), the division factor setting should observe the following order: 1. Select an input clock by the PRE_DIV_CH_VALUE[3:0] bits; 2. Write the lower eight bits of the division factor to the PRE_DIVN_VALUE[7:0] bits; 3. Write the higher eight bits of the division factor to the PRE_DIVN_VALUE[14:8] bits. Once the division factor is set for the input clock selected by the PRE_DIV_CH_VALUE[3:0] bits, it is valid until a different division factor is set for the same input clock. The division factor is calculated as follows: Division Factor = (the frequency of the clock input to the DivN Divider / the frequency of the DPLL required clock set by the IN_FREQ[3:0] bits) - 1 The DivN Divider can only divide the input clock whose frequency is lower than (<) 155.52 MHz. When the Lock 8k Divider is used, the input clock is divided down to 8 kHz automatically. The Pre-Divider configuration and the division factor setting depend on the input clock on one of the IN3 ~ IN14 pins and the DPLL required clock. Here is an example: The input clock on the IN6 pin is 622.08 MHz; the DPLL required clock is 6.48 MHz by programming the IN_FREQ[3:0] bits of register IN6 to `0010'. Do the following step by step to divide the input clock: 1. Use the HF Divider to divide the clock down to 155.52 MHz: 622.08 / 155.52 = 4, so set the IN6_DIV[1:0] bits to `01'; 2. Use the DivN Divider to divide the clock down to 6.48 MHz: Set the PRE_DIV_CH_VALUE[3:0] bits to `0110'; Set the DIRECT_DIV bit in Register IN6_CNFG to `1' and the LOCK_8K bit in Register IN6_CNFG to `0'; 155.52 / 6.48 = 24; 24 - 1 = 23, so set the PRE_DIVN_VALUE[14:0] bits to `10111'. Pre-Divider IN5_DIV[1:0] bits / IN6_DIV[1:0] bits Input Clock INn (14>n>3) HF Divider (for IN5 & IN6 only) DIRECT_DIV bit LOCK_8K bit DivN Divider Lock 8k Divider DPLL required clock Figure 3. Pre-Divider for An Input Clock Functional Description 21 June 19, 2006 IDT82V3280 WAN PLL Table 4: Related Bit / Register in Chapter 3.4 Bit IN5_DIV[1:0] IN6_DIV[1:0] IN_FREQ[3:0] IN_2K_4K_8K_INV DIRECT_DIV LOCK_8K PRE_DIV_CH_VALUE[3:0] PRE_DIVN_VALUE[14:0] Register IN5_IN6_HF_DIV_CNFG IN1_CNFG ~ IN14_CNFG FR_MFR_SYNC_CNFG IN3_CNFG ~ IN14_CNFG PRE_DIV_CH_CNFG PRE_DIVN[14:8]_CNFG, PRE_DIVN[7:0]_CNFG Address (Hex) 18 14 ~ 17, 19 ~ 22 74 16, 17, 19 ~ 22 23 25, 24 Functional Description 22 June 19, 2006 IDT82V3280 WAN PLL 3.5 INPUT CLOCK QUALITY MONITORING The qualities of all the input clocks are always monitored in the following aspects: * LOS (loss of signal) (only for IN1 and IN2) * Activity * Frequency LOS monitoring is only conducted on IN1 and IN2. Activity and frequency monitoring are conducted on all the input clocks. The qualified clocks are available for T0/T4 DPLL selection. The T0 and T4 selected input clocks have to be monitored further. Refer to Chapter 3.7 Selected Input Clock Monitoring for details. 3.5.1 LOS MONITORING IN1 and IN2 support the AMI input signal. LOS monitoring is conducted on IN1 and IN2. A LOS event occurs when the amplitude of the input clock falls below +0.6 Vp-p for 1 ms; the LOS event is cleared when the amplitude rises higher than +1 Vp-p. LOS status is indicated by the AMI1_LOS 1 / AMI2_LOS 1 bit. If the AMI1_LOS 2 / AMI2_LOS 2 bit is `1', the occurrence of LOS will trigger an interrupt. The input clock in LOS status is disqualified for clock selection for T0/ T4 DPLL. 3.5.2 ACTIVITY MONITORING Activity is monitored by using an internal leaky bucket accumulator, as shown in Figure 4. Each input clock is assigned an internal leaky bucket accumulator. The input clock is monitored for each period of 128 ms and the internal leaky bucket accumulator increases by 1 when an event is detected; it decreases by 1 if no event is detected within the period set by the decay rate. The event is that an input clock drifts outside (>) 500 ppm with respect to the master clock within a 128 ms period. There are four configurations (0 - 3) for a leaky bucket accumulator. The leaky bucket configuration for an input clock is selected by the corresponding BUCKET_SEL[1:0] bits. Each leaky bucket configuration consists of four elements: upper threshold, lower threshold, bucket size and decay rate. The bucket size is the capability of the accumulator. If the number of the accumulated events reach the bucket size, the accumulator will stop increasing even if further events are detected. The upper threshold is a point above which a no-activity alarm is raised. The lower threshold is a point below which the no-activity alarm is cleared. The decay rate is a certain period during which the accumulator decreases by 1 if no event is detected. The leaky bucket configuration is programmed by one of four groups of register bits: the BUCKET_SIZE_n_DATA[7:0] bits, the UPPER_ THRESHOLD_n_DATA[7:0] bits, the LOWER_THRESHOLD_n_ DATA[7:0] bits and the DECAY_RATE_n_DATA[1:0] bits respectively; `n' is 0 ~ 3. The no-activity alarm status of the input clock is indicated by the INn_NO_ACTIVITY_ALARM bit (14 n 1). The input clock with a no-activity alarm is disqualified for clock selection for T0/T4 DPLL. clock signal with events clock signal with no event Input Clock Decay Rate Leaky Bucket Accumulator Bucket Size Upper Threshold Lower Threshold 0 No-activity Alarm Indication Figure 4. Input Clock Activity Monitoring Functional Description 23 June 19, 2006 IDT82V3280 WAN PLL 3.5.3 FREQUENCY MONITORING Frequency is monitored by comparing the input clock with a reference clock. The reference clock can be derived from the master clock or the output of T0 DPLL, as determined by the FREQ_MON_CLK bit. A frequency hard alarm threshold is set for frequency monitoring. If the FREQ_MON_HARD_EN bit is `1', a frequency hard alarm is raised when the frequency of the input clock with respect to the reference clock is above the threshold; the alarm is cleared when the frequency is below the threshold. The frequency hard alarm threshold can be calculated as follows: Frequency Hard Alarm Threshold (ppm) = (ALL_FREQ_HARD_ THRESHOLD[3:0] + 1) X FREQ_MON_FACTOR[3:0] The input clock with a frequency hard alarm is disqualified for clock selection for T0/T4 DPLL. In addition, if the input clock is 2 kHz, 4 kHz or 8 kHz, its clock edges with respect to the reference clock are monitored. If any edge drifts outside 5%, the input clock is disqualified for clock selection for T0/T4 DPLL. The input clock is qualified if any edge drifts inside 5%. This function is supported only when the IN_NOISE_WINDOW bit is `1'. The frequency of each input clock with respect to the reference clock can be read by doing the following step by step: 1. Select an input clock by setting the IN_FREQ_READ_CH[3:0] bits; 2. Read the value in the IN_FREQ_VALUE[7:0] bits and calculate as follows: Input Clock Frequency (ppm) = IN_FREQ_VALUE[7:0] X FREQ_MON_FACTOR[3:0] If the FREQ_MON_HARD_EN bit is `1', the frequency hard alarm status of the input clock is indicated by the INn_FREQ_HARD_ALARM bit (14 n 1). When the FREQ_MON_HARD_EN bit is `0', no frequency hard alarm is raised even if the input clock is above the frequency hard alarm threshold. Table 5: Related Bit / Register in Chapter 3.5 Bit AMI1_LOS 1 AMI2_LOS 1 AMI1_LOS 2 AMI2_LOS 2 BUCKET_SIZE_n_DATA[7:0] (3 n 0) UPPER_THRESHOLD_n_DATA[7:0] (3 n 0) LOWER_THRESHOLD_n_DATA[7:0] (3 n 0) DECAY_RATE_n_DATA[1:0] (3 n 0) BUCKET_SEL[1:0] INn_NO_ACTIVITY_ALARM (14 n 1) INn_FREQ_HARD_ALARM (14 n 1) FREQ_MON_CLK FREQ_MON_HARD_EN ALL_FREQ_HARD_THRESHOLD[3:0] FREQ_MON_FACTOR[3:0] IN_NOISE_WINDOW IN_FREQ_READ_CH[3:0] IN_FREQ_VALUE[7:0] Note that the value set by the FREQ_MON_FACTOR[3:0] bits depends on the application. Register INTERRUPTS3_STS INTERRUPTS3_ENABLE_CNFG BUCKET_SIZE_0_CNFG ~ BUCKET_SIZE_3_CNFG UPPER_THRESHOLD_0_CNFG ~ UPPER_THRESHOLD_3_CNFG LOWER_THRESHOLD_0_CNFG ~ LOWER_THRESHOLD_3_CNFG DECAY_RATE_0_CNFG ~ DECAY_RATE_3_CNFG IN1_CNFG ~ IN14_CNFG IN1_IN2_STS ~ IN13_IN14_STS MON_SW_PBO_CNFG ALL_FREQ_MON_THRESHOLD_CNFG FREQ_MON_FACTOR_CNFG PHASE_MON_PBO_CNFG IN_FREQ_READ_CH_CNFG IN_FREQ_READ_STS Address (Hex) 0F 12 33, 37, 3B, 3F 31, 35, 39, 3D 32, 36, 3A, 3E 34, 38, 3C, 40 14 ~ 17, 19 ~ 22 43 ~ 49 0B 2F 2E 78 41 42 Functional Description 24 June 19, 2006 IDT82V3280 WAN PLL 3.6 T0 / T4 DPLL INPUT CLOCK SELECTION An input clock is selected for T0 DPLL and for T4 DPLL respectively. For T0 path, the EXT_SW bit and the T0_INPUT_SEL[3:0] bits determine the input clock selection, as shown in Table 6: Table 6: Input Clock Selection for T0 Path Control Bits EXT_SW 1 0 T0_INPUT_SEL[3:0] don't-care other than 0000 0000 Input Clock Selection External Fast selection Forced selection Automatic selection Automatic selection is done based on the results of input clocks quality monitoring and the related registers configuration. The selected input clock is attempted to be locked in T0/T4 DPLL. 3.6.1 EXTERNAL FAST SELECTION (T0 ONLY) The External Fast selection is supported by T0 path only. In External Fast selection, only IN3/IN5 and IN4/IN6 pairs are available for selection. Refer to Figure 5. The results of input clocks quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring) do not affect input clock selection. The T0 input clock selection is determined by the FF_SRCSW pin after reset (this pin determines the default value of the EXT_SW bit during reset, refer to Chapter 2 Pin Description), the IN3_SEL_PRIORITY[3:0] bits and the IN4_SEL_PRIORITY[3:0] bits, as shown in Figure 5 and Table 8: IN3_SEL_PRIORITY[3:0] bits IN3 IN5 attempted to be locked in T0 DPLL IN4 IN6 FF_SRCSW pin For T4 path, the T4 DPLL may lock to a T0 DPLL output or lock independently from T0 path, as determined by the T4_LOCK_T0 bit. When the T4 DPLL locks to the T0 DPLL output, the T4 selected input clock is a 77.76 MHz or 8 kHz signal from the T0 DPLL 77.76 MHz path (refer to Chapter 3.11.5.1 T0 Path), as determined by the T0_FOR_T4 bit. When the T4 path locks independently from the T0 path, the T4 DPLL input clock selection is determined by the T4_INPUT_SEL[3:0] bits. Refer to Table 7: Table 7: Input Clock Selection for T4 Path Control Bits - T4_INPUT_SEL[3:0] other than 0000 0000 Input Clock Selection Forced selection Automatic selection External Fast selection is done between IN3/IN5 and IN4/IN6 pairs. Forced selection is done by setting the related registers. Table 8: External Fast Selection Control Pin & Bits FF_SRCSW (after reset) high low IN3_SEL_PRIORITY[3:0] 0000 other than 0000 don't-care IN4_SEL_PRIORITY[3:0] bits Figure 5. External Fast Selection IN4_SEL_PRIORITY[3:0] don't-care 0000 other than 0000 the Selected Input Clock IN5 IN3 IN6 IN4 Functional Description 25 June 19, 2006 IDT82V3280 WAN PLL 3.6.2 FORCED SELECTION In Forced selection, the selected input clock is set by the T0_INPUT_SEL[3:0] / T4_INPUT_SEL[3:0] bits. The results of input clocks quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring) do not affect the input clock selection. 3.6.3 AUTOMATIC SELECTION In Automatic selection, the input clock selection is determined by its validity, priority and locking allowance configuration. The validity depends on the results of input clock quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring). Locking allowance is configured by the corresponding INn_VALID bit(14 n 1). Refer to Figure 6. In all the qualified input clocks, the one with the highest priority is selected. The priority is set by the corresponding INn_SEL_PRIORITY[3:0] bits (14 n 1). If more than one qualified input clock INn is available and has the same priority, the input clock with the smallest `n' is selected. Validity Priority Locking Allowance No No No Input Clock Quality Monitoring (LOS, Activity, Frequency) INn = '1', (14 > n > 1) INn_SEL_PRIORITY[3:0] '0000', (14 > n > 1) INn_VALID = '0', (14 > n > 1) Yes Yes All qualified input clocks are available for Automatic selection Yes Figure 6. Qualified Input Clocks for Automatic Selection Table 9: Related Bit / Register in Chapter 3.6 Bit EXT_SW T0_INPUT_SEL[3:0] T4_LOCK_T0 T0_FOR_T4 T4_INPUT_SEL[3:0] INn_SEL_PRIORITY[3:0] (14 n 1) INn_VALID (14 n 1) INn (14 n 1) T4_T0_SEL Register MON_SW_PBO_CNFG T0_INPUT_SEL_CNFG T4_INPUT_SEL_CNFG IN1_IN2_SEL_PRIORITY_CNFG ~ IN13_IN14_SEL_PRIORITY_CNFG REMOTE_INPUT_VALID1_CNFG, REMOTE_INPUT_VALID2_CNFG INPUT_VALID1_STS, INPUT_VALID2_STS T4_T0_REG_SEL_CNFG Address (Hex) 0B 50 51 26 ~ 2C * 4C, 4D 4A, 4B 07 Note: * The setting in the 26 ~ 2C registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit. Functional Description 26 June 19, 2006 IDT82V3280 WAN PLL 3.7 SELECTED INPUT CLOCK MONITORING 3.7.1.3 Fine Phase Loss The quality of the selected input clock is always monitored (refer to Chapter 3.5 Input Clock Quality Monitoring) and the DPLL locking status is always monitored. 3.7.1 T0 / T4 DPLL LOCKING DETECTION The following events is always monitored: * Fast Loss; * Coarse Phase Loss; * Fine Phase Loss; * Hard Limit Exceeding. 3.7.1.1 Fast Loss A fast loss is triggered when the selected input clock misses 2 consecutive clock cycles. It is cleared once an active clock edge is detected. For T0 path, the occurrence of the fast loss will result in T0 DPLL unlocked if the FAST_LOS_SW bit is `1'. For T4 path, the occurrence of the fast loss will result in T4 DPLL unlocked regardless of the FAST_LOS_SW bit. 3.7.1.2 Coarse Phase Loss The T0/T4 DPLL compares the selected input clock with the feedback signal. If the phase-compared result exceeds the coarse phase limit, a coarse phase loss is triggered. It is cleared once the phase-compared result is within the coarse phase limit. When the selected input clock is of 2 kHz, 4 kHz or 8 kHz, the coarse phase limit depends on the MULTI_PH_8K_4K_2K_EN bit, the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to Table 10. When the selected input clock is of other frequencies but 2 kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to Table 11. Table 10: Coarse Phase Limit Programming (the selected input clock of 2 kHz, 4 kHz or 8 kHz) MULTI_PH_8K_4K WIDE_EN _2K_EN 0 1 Coarse Phase Limit The T0/T4 DPLL compares the selected input clock with the feedback signal. If the phase-compared result exceeds the fine phase limit programmed by the PH_LOS_FINE_LIMT[2:0] bits, a fine phase loss is triggered. It is cleared once the phase-compared result is within the fine phase limit. The occurrence of the fine phase loss will result in T0/T4 DPLL unlocked if the FINE_PH_LOS_LIMT_EN bit is `1'. 3.7.1.4 Hard Limit Exceeding Two limits are available for this monitoring. They are DPLL soft limit and DPLL hard limit. When the frequency of the DPLL output with respect to the master clock exceeds the DPLL soft / hard limit, a DPLL soft / hard alarm will be raised; the alarm is cleared once the frequency is within the corresponding limit. The occurrence of the DPLL soft alarm does not affect the T0/T4 DPLL locking status. The DPLL soft alarm is indicated by the corresponding T0_DPLL_SOFT_FREQ_ALARM / T4_DPLL_SOFT_FREQ_ALARM bit. The occurrence of the DPLL hard alarm will result in T0/T4 DPLL unlocked if the FREQ_LIMT_PH_LOS bit is `1'. The DPLL soft limit is set by the DPLL_FREQ_SOFT_LIMT[6:0] bits and can be calculated as follows: DPLL Soft Limit (ppm) = DPLL_FREQ_SOFT_LIMT[6:0] X 0.724 The DPLL hard limit is set by the DPLL_FREQ_HARD_LIMT[15:0] bits and can be calculated as follows: DPLL Hard Limit (ppm) = DPLL_FREQ_HARD_LIMT[15:0] X 0.0014 3.7.2 LOCKING STATUS don't-care 1 UI 0 1 UI 1 set by the PH_LOS_COARSE_LIMT[3:0] bits The DPLL locking status depends on the locking monitoring results. The DPLL is in locked state if none of the following events is triggered during 2 seconds; otherwise, the DPLL is unlocked. * Fast Loss (the FAST_LOS_SW bit is `1'); * Coarse Phase Loss (the COARSE_PH_LOS_LIMT_EN bit is `1'); * Fine Phase Loss (the FINE_PH_LOS_LIMT_EN bit is `1'); * DPLL Hard Alarm (the FREQ_LIMT_PH_LOS bit is `1'). If the FAST_LOS_SW bit, the COARSE_PH_LOS_LIMT_EN bit, the FINE_PH_LOS_LIMT_EN bit or the FREQ_LIMT_PH_LOS bit is `0', the DPLL locking status will not be affected even if the corresponding event is triggered. If all these bits are `0', the DPLL will be in locked state in 2 seconds. The DPLL locking status is indicated by the T0_DPLL_LOCK / T4_DPLL_LOCK bit. The T4_STS 1 bit will be set when the locking status of the T4 DPLL changes (from `lock' to `unlock' or from `unlock' to `lock'). If the T4_STS 2 bit is `1', an interrupt will be generated. Table 11: Coarse Phase Limit Programming (the selected input clock of other than 2 kHz, 4 kHz and 8 kHz) WIDE_EN 0 1 Coarse Phase Limit 1 UI set by the PH_LOS_COARSE_LIMT[3:0] bits The occurrence of the coarse phase loss will result in T0/T4 DPLL unlocked if the COARSE_PH_LOS_LIMT_EN bit is `1'. Functional Description 27 June 19, 2006 IDT82V3280 WAN PLL 3.7.3 PHASE LOCK ALARM (T0 ONLY) A phase lock alarm will be raised when the selected input clock can not be locked in T0 DPLL within a certain period. This period can be calculated as follows: Period (sec.) = TIME_OUT_VALUE[5:0] X MULTI_FACTOR[1:0] * Be cleared when a `1' is written to the corresponding INn_PH_LOCK_ALARM bit; * Be cleared after the period (= TIME_OUT_VALUE[5:0] X MULTI_FACTOR[1:0] in second) which starts from when the alarm is raised. The selected input clock with a phase lock alarm is disqualified for T0 DPLL locking. Note that no phase lock alarm is raised if the T4 selected input clock can not be locked. The phase lock alarm is indicated by the corresponding INn_PH_LOCK_ALARM bit (14 n 1). The phase lock alarm can be cleared by the following two ways, as selected by the PH_ALARM_TIMEOUT bit: Table 12: Related Bit / Register in Chapter 3.7 Bit FAST_LOS_SW PH_LOS_FINE_LIMT[2:0] FINE_PH_LOS_LIMT_EN MULTI_PH_8K_4K_2K_EN WIDE_EN PH_LOS_COARSE_LIMT[3:0] COARSE_PH_LOS_LIMT_EN T0_DPLL_SOFT_FREQ_ALARM T4_DPLL_SOFT_FREQ_ALARM T0_DPLL_LOCK T4_DPLL_LOCK DPLL_FREQ_SOFT_LIMT[6:0] FREQ_LIMT_PH_LOS DPLL_FREQ_HARD_LIMT[15:0] T4_STS 1 T4_STS TIME_OUT_VALUE[5:0] MULTI_FACTOR[1:0] INn_PH_LOCK_ALARM (14 n 1) PH_ALARM_TIMEOUT T4_T0_SEL 2 Register PHASE_LOSS_FINE_LIMIT_CNFG Address (Hex) 5B * PHASE_LOSS_COARSE_LIMIT_CNFG 5A * OPERATING_STS 52 DPLL_FREQ_SOFT_LIMIT_CNFG DPLL_FREQ_HARD_LIMIT[15:8]_CNFG, DPLL_FREQ_HARD_LIMIT[7:0]_CNFG INTERRUPTS3_STS INTERRUPTS3_ENABLE_CNFG PHASE_ALARM_TIME_OUT_CNFG IN1_IN2_STS ~ IN13_IN14_STS INPUT_MODE_CNFG T4_T0_REG_SEL_CNFG 65 67, 66 0F 12 08 43 ~ 49 09 07 Note: * The setting in the 5A and 5B registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit. Functional Description 28 June 19, 2006 IDT82V3280 WAN PLL 3.8 SELECTED INPUT CLOCK SWITCH If the input clock is selected by External Fast selection or by Forced selection, it can be switched by setting the related registers (refer to Chapter 3.6.1 External Fast Selection (T0 only) & Chapter 3.6.2 Forced Selection) any time. In this case, whether the input clock is qualified for DPLL locking does not affect the clock switch. If the T4 selected input clock is a T0 DPLL output, it can only be switched by setting the T0_FOR_T4 bit. When the input clock is selected by Automatic selection, the input clock switch depends on its validity, priority and locking allowance configuration. If the current selected input clock is disqualified, a new qualified input clock may be switched to. 3.8.1 INPUT CLOCK VALIDITY For all the input clocks, the validity depends on the results of input clock quality monitoring (refer to Chapter 3.5 Input Clock Quality Monitoring). When all of the following conditions are satisfied, the input clock is valid; otherwise, it is invalid. * No LOS (the AMI1_LOS / AMI2_LOS bit is `0'); * No no-activity alarm (the INn_NO_ACTIVITY_ALARM bit is `0'); * No frequency hard alarm (the INn_FREQ_HARD_ALARM bit is `0'); * If the IN_NOISE_WINDOW bit is `1', all the edges of the input clock of 2 kHz, 4 kHz or 8 kHz drift inside 5%; if the IN_NOISE_WINDOW bit is `0', this condition is ignored. The validity qualification of the T0 selected input clock is different from that of the T4 selected input clock. The validity qualification of the T4 selected input clock is the same as the above. The T0 selected input clock is valid when all of the above and the following conditions are satisfied; otherwise, it is invalid. * No phase lock alarm, i.e., the INn_PH_LOCK_ALARM bit is `0'; * If the ULTR_FAST_SW bit is `1', the T0 selected input clock misses less than (<) 2 consecutive clock cycles; if the ULTR_FAST_SW bit is `0', this condition is ignored. The validities of all the input clocks are indicated by the INn 1 bit (14 n 1). When the input clock validity changes (from `valid' to `invalid' or from `invalid' to `valid'), the INn 2 bit will be set. If the INn 3 bit is `1', an interrupt will be generated. When the T0 selected input clock has failed, i.e., the validity of the T0 selected input clock changes from `valid' to `invalid', the T0_MAIN_REF_FAILED 1 bit will be set. If the T0_MAIN_REF_FAILED 2 bit is `1', an interrupt will be generated. This interrupt can also be indicated by hardware - the TDO pin, as determined by the LOS_FLAG_TO_TDO bit. When the TDO pin is used to indicate this interrupt, it will be set high when this interrupt is generated and will remain high until this interrupt is cleared. 3.8.2 SELECTED INPUT CLOCK SWITCH When the device is configured as Automatic input clock selection, T0 input clock switch is different from T4 input clock switch. For T0 path, Revertive and Non-Revertive switches are supported, as selected by the REVERTIVE_MODE bit. For T4 path, only Revertive switch is supported. The difference between Revertive and Non-Revertive switches is that whether the selected input clock is switched when another qualified input clock with a higher priority than the current selected input clock is available for selection. In Non-Revertive switch, input clock switch is minimized. Conditions of the qualified input clocks available for T0 selection are different from that for T4 selection, as shown in Table 13: Table 13: Conditions of Qualified Input Clocks Available for T0 & T4 Selection Conditions of Qualified Input Clocks Available for T0 & T4 Selection * Valid, i.e., the INn 1 bit is `1'; * Priority enabled, i.e., the corresponding INn_SEL_PRIORITY[3:0] bits T0 are not `0000'; * Locking to the input clock is allowed, i.e., the corresponding INn_VALID bit is `0'. * Valid (all the validity conditions listed in Chapter 3.8.1 Input Clock Validity are satisfied); * Priority enabled, i.e., the corresponding INn_SEL_PRIORITY[3:0] bits T4 are not `0000'; * Locking to the input clock is allowed, i.e., the corresponding INn_VALID bit is `0'. The input clock is disqualified if any of the above conditions is not satisfied. In summary, the selected input clock can be switched by: * External Fast selection (supported by T0 path only); * Forced selection; * Revertive switch; * Non-Revertive switch (supported by T0 path only); * T4 DPLL locked to T0 DPLL output (supported by T4 path only). 3.8.2.1 Revertive Switch In Revertive switch, the selected input clock is switched when another qualified input clock with a higher priority than the current selected input clock is available. The selected input clock is switched if any of the following is satisfied: * the selected input clock is disqualified; * another qualified input clock with a higher priority than the selected input clock is available. A qualified input clock with the highest priority is selected by revertive switch. If more than one qualified input clock INn is available and has the same priority, the input clock with the smallest `n' is selected. Functional Description 29 June 19, 2006 IDT82V3280 WAN PLL 3.8.2.2 Non-Revertive Switch (T0 only) In Non-Revertive switch, the T0 selected input clock is not switched when another qualified input clock with a higher priority than the current selected input clock is available. In this case, the selected input clock is switched and a qualified input clock with the highest priority is selected only when the T0 selected input clock is disqualified. If more than one qualified input clock is available and has the same priority, the input clock with the smallest `n' is selected. 3.8.3 SELECTED / QUALIFIED INPUT CLOCKS INDICATION The selected input clock is indicated by the CURRENTLY_SELECTED_INPUT[3:0] bits. Note if the T4 selected input clock is a T0 DPLL output, it can not be indicated by these bits. The qualified input clocks with the three highest priorities are indicated by HIGHEST_PRIORITY_VALIDATED[3:0] bits, the SECOND_ PRIORITY_VALIDATED[3:0] bits and the THIRD_PRIORITY _VALIDATED[3:0] bits respectively. If more than one input clock INn has the same priority, the input clock with the smallest `n' is indicated by the HIGHEST_PRIORITY_VALIDATED[3:0] bits. When the device is configured in Automatic selection and Revertive switch is enabled, the input clock indicated by the CURRENTLY_SELECTED_INPUT[3:0] bits is the same as the one indicated by the HIGHEST_PRIORITY_VALIDATED[3:0] bits; otherwise, they are not the same. When all the input clocks for T4 path changes to be unqualified, the INPUT_TO_T4 1 bit will be set. If the INPUT_TO_T4 2 bit is `1', an interrupt will be generated. Table 14: Related Bit / Register in Chapter 3.8 Bit T0_FOR_T4 INn 1 (14 n 1) INn 2 (14 n 1) INn AMI1_LOS AMI2_LOS 3 (14 n 1) Register T4_INPUT_SEL_CNFG INPUT_VALID1_STS, INPUT_VALID2_STS INTERRUPTS1_STS, INTERRUPTS2_STS INTERRUPTS1_ENABLE_CNFG, INTERRUPTS2_ENABLE_CNFG INTERRUPTS3_STS Address (Hex) 51 4A, 4B 0D, 0E 10, 11 0F INn_NO_ACTIVITY_ALARM (14 n 1) INn_FREQ_HARD_ALARM (14 n 1) INn_PH_LOCK_ALARM (14 n 1) IN_NOISE_WINDOW ULTR_FAST_SW LOS_FLAG_TO_TDO T0_MAIN_REF_FAILED 1 T0_MAIN_REF_FAILED 2 INPUT_TO_T4 1 2 IN1_IN2_STS ~ IN13_IN14_STS PHASE_MON_PBO_CNFG MON_SW_PBO_CNFG INTERRUPTS2_STS INTERRUPTS2_ENABLE_CNFG INTERRUPTS3_STS INTERRUPTS3_ENABLE_CNFG INPUT_MODE_CNFG IN1_IN2_SEL_PRIORITY_CNFG ~ IN13_IN14_SEL_PRIORITY_CNFG REMOTE_INPUT_VALID1_CNFG, REMOTE_INPUT_VALID2_CNFG PRIORITY_TABLE1_STS PRIORITY_TABLE2_STS T4_T0_REG_SEL_CNFG 43 ~ 49 78 0B 0E 11 0F 12 09 26 ~ 2C * 4C, 4D 4E * 4F * 07 INPUT_TO_T4 REVERTIVE_MODE INn_SEL_PRIORITY[3:0] (14 n 1) INn_VALID (14 n 1) CURRENTLY_SELECTED_INPUT[3:0] HIGHEST_PRIORITY_VALIDATED[3:0] SECOND_PRIORITY_VALIDATED[3:0] THIRD_PRIORITY_VALIDATED[3:0] T4_T0_SEL Note: * The setting in the 26 ~ 2C, 4E and 4F registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit. Functional Description 30 June 19, 2006 IDT82V3280 WAN PLL 3.9 SELECTED INPUT CLOCK STATUS VS. DPLL OPERATING MODE 3.9.1 T0 SELECTED INPUT CLOCK VS. DPLL OPERATING MODE by the The operating modes supported by T0 DPLL are more complex than the ones supported by T4 DPLL for T0 path is the main one. T0 DPLL supports three primary operating modes: Free-Run, Locked and Holdover, and three secondary, temporary operating modes: Pre-Locked, Pre-Locked2 and Lost-Phase. T4 DPLL supports three operating modes: Free-Run, Locked and Holdover. The operating modes of T0 DPLL and T4 DPLL can be switched automatically or by force, as controlled by the T0_OPERATING_MODE[2:0] / T4_OPERATING_ MODE[2:0] bits respectively. When the operating mode is switched by force, the operating mode switch is under external control and the status of the selected input clock takes no effect to the operating mode selection. The forced operating mode switch is applicable for special cases, such as testing. When the operating mode is switched automatically, the internal state machines for T0 and for T4 automatically determine the operating mode respectively. The T0 DPLL operating mode is controlled T0_OPERATING_MODE[2:0] bits, as shown in Table 15: Table 15: T0 DPLL Operating Mode Control T0_OPERATING_MODE[2:0] 000 001 010 100 101 110 111 T0 DPLL Operating Mode Automatic Forced - Free-Run Forced - Holdover Forced - Locked Forced - Pre-Locked2 Forced - Pre-Locked Forced - Lost-Phase When the operating mode is switched automatically, the operation of the internal state machine is shown in Figure 7. Whether the operating mode is under external control or is switched automatically, the current operating mode is always indicated by the T0_DPLL_OPERATING_MODE[2:0] bits. When the operating mode switches, the T0_OPERATING_MODE 1 bit will be set. If the T0_OPERATING_MODE 2 bit is `1', an interrupt will be generated. Functional Description 31 June 19, 2006 IDT82V3280 WAN PLL 1 Free-Run mode 3 2 4 Pre-Locked mode 5 10 Locked mode 6 Holdover mode 9 8 7 11 15 Pre-Locked2 mode 12 Lost-Phase mode 13 14 Figure 7. T0 Selected Input Clock vs. DPLL Automatic Operating Mode Notes to Figure 7: 1. Reset. 2. An input clock is selected. 3. The T0 selected input clock is disqualified AND No qualified input clock is available. 4. The T0 selected input clock is switched to another one. 5. The T0 selected input clock is locked (the T0_DPLL_LOCK bit is `1'). 6. The T0 selected input clock is disqualified AND No qualified input clock is available. 7. The T0 selected input clock is unlocked (the T0_DPLL_LOCK bit is `0'). 8. The T0 selected input clock is locked again (the T0_DPLL_LOCK bit is `1'). 9. The T0 selected input clock is switched to another one. 10. The T0 selected input clock is locked (the T0_DPLL_LOCK bit is `1'). 11. The T0 selected input clock is disqualified AND No qualified input clock is available. 12. The T0 selected input clock is switched to another one. 13. The T0 selected input clock is disqualified AND No qualified input clock is available. 14. An input clock is selected. 15. The T0 selected input clock is switched to another one. Functional Description 32 June 19, 2006 IDT82V3280 WAN PLL The causes of Item 4, 9, 12, 15 - `the T0 selected input clock is switched to another one' - are: (The T0 selected input clock is disqualified AND Another input clock is switched to) OR (In Revertive switch, a qualified input clock with a higher priority is switched to) OR (The T0 selected input clock is switched to another one by External Fast selection or Forced selection). Refer to Table 13 for details about the input clock qualification for T0 path. 3.9.2 T4 SELECTED INPUT CLOCK VS. DPLL OPERATING MODE by the Notes to Figure 8: 1. Reset. 2. An input clock is selected. 3. (The T4 selected input clock is disqualified) OR (A qualified input clock with a higher priority is switched to) OR (The T4 selected input clock is switched to another one by Forced selection) OR (When T4 DPLL locks to the T0 DPLL output, the T4 selected input clock is switched by setting the T0_FOR_T4 bit). 4. An input clock is selected. 5. No input clock is selected. Refer to Table 13 for details about the input clock qualification for T4 path. Table 17: Related Bit / Register in Chapter 3.9 Bit Register Address (Hex) 53 54 52 0E 11 51 The T4 DPLL operating mode is controlled T4_OPERATING_MODE[2:0] bits, as shown in Table 16: Table 16: T4 DPLL Operating Mode Control T4_OPERATING_MODE[2:0] 000 001 010 100 T4 DPLL Operating Mode Automatic Forced - Free-Run Forced - Holdover Forced - Locked When the operating mode is switched automatically, the operation of the internal state machine is shown in Figure 8: 1 Free-Run mode 2 T0_OPERATING_MODE[2:0] T0_OPERATING_MODE_CNFG T4_OPERATING_MODE[2:0] T4_OPERATING_MODE_CNFG T0_DPLL_OPERATING_MOD E[2:0] OPERATING_STS T0_DPLL_LOCK T0_OPERATING_MODE 1 T0_OPERATING_MODE T0_FOR_T4 2 INTERRUPTS2_STS INTERRUPTS2_ENABLE_CNFG T4_INPUT_SEL_CNFG Locked mode 3 Holdover mode 4 5 Figure 8. T4 Selected Input Clock vs. DPLL Automatic Operating Mode Functional Description 33 June 19, 2006 IDT82V3280 WAN PLL 3.10 T0 / T4 DPLL OPERATING MODE 3.10.1.1 Free-Run Mode The T0/T4 DPLL gives a stable performance in different applications without being affected by operating conditions or silicon process variations. It integrates a PFD (Phase & Frequency Detector), a LPF (Low Pass Filter) and a DCO (Digital Controlled Oscillator), which forms a closed loop. If no input clock is selected, the loop is not closed, and the PFD and LPF do not function. The PFD detects the phase error, including the fast loss, coarse phase loss and fine phase loss (refer to Chapter 3.7.1.1 Fast Loss to Chapter 3.7.1.3 Fine Phase Loss). The averaged phase error of the T0/ T4 DPLL feedback with respect to the selected input clock is indicated by the CURRENT_PH_DATA[15:0] bits. It can be calculated as follows: Averaged Phase Error (ns) = CURRENT_PH_DATA[15:0] X 0.61 In Free-Run mode, the T0 DPLL output refers to the master clock and is not affected by any input clock. The accuracy of the T0 DPLL output is equal to that of the master clock. 3.10.1.2 Pre-Locked Mode In Pre-Locked mode, the T0 DPLL output attempts to track the selected input clock. The Pre-Locked mode is a secondary, temporary mode. 3.10.1.3 Locked Mode In Locked mode, the T0 selected input clock is locked. The phase and frequency offset of the T0 DPLL output track those of the T0 selected input clock. In this mode, if the T0 selected input clock is in fast loss status and the FAST_LOS_SW bit is `1', the T0 DPLL is unlocked (refer to Chapter 3.7.1.1 Fast Loss) and will enter Lost-Phase mode when the operating mode is switched automatically; if the T0 selected input clock is in fast loss status and the FAST_LOS_SW bit is `0', the T0 DPLL locking status is not affected and the T0 DPLL will enter Temp-Holdover mode automatically. 3.10.1.3.1 Temp-Holdover Mode The T0 DPLL will automatically enter Temp-Holdover mode with a selected input clock switch or no qualified input clock available when the operating mode switch is under external control. In Temp-Holdover mode, the T0 DPLL has temporarily lost the selected input clock. The T0 DPLL operation in Temp-Holdover mode and that in Holdover mode are alike (refer to Chapter 3.10.1.5 Holdover Mode) except the frequency offset acquiring methods. See Chapter 3.10.1.5 Holdover Mode for details about the methods. The method is selected by the TEMP_HOLDOVER_MODE[1:0] bits, as shown in Table 18: Table 18: Frequency Offset Control in Temp-Holdover Mode TEMP_HOLDOVER_MODE[1:0] 00 01 10 11 Frequency Offset Acquiring Method the same as that used in Holdover mode Automatic Instantaneous Automatic Fast Averaged Automatic Slow Averaged The LPF filters jitters. Its 3 dB bandwidth and damping factor are programmable. A range of bandwidths and damping factors can be set to meet different application requirements. Generally, the lower the damping factor is, the longer the locking time is and the more the gain is. The DCO controls the DPLL output. The frequency of the DPLL output is always multiplied on the basis of the master clock. The phase and frequency offset of the DPLL output may be locked to those of the selected input clock. The current frequency offset with respect to the master clock is indicated by the CURRENT_DPLL_FREQ[23:0] bits, and can be calculated as follows: Current Frequency Offset (ppm) = CURRENT_DPLL_FREQ[23:0] X 0.000011 3.10.1 T0 DPLL OPERATING MODE The T0 DPLL loop is closed except in Free-Run mode and Holdover mode. For a closed loop, different bandwidths and damping factors can be used depending on DPLL locking stages: starting, acquisition and locked. In the first two seconds when the T0 DPLL attempts to lock to the selected input clock, the starting bandwidth and damping factor are used. They are set by the T0_DPLL_START_BW[4:0] bits and the T0_DPLL_START_DAMPING[2:0] bits respectively. During the acquisition, the acquisition bandwidth and damping factor are used. They are set by the T0_DPLL_ACQ_BW[4:0] bits and the T0_DPLL_ACQ_DAMPING[2:0] bits respectively. When the T0 selected input clock is locked, the locked bandwidth and damping factor are used. They are set by the T0_DPLL_LOCKED_BW[4:0] bits and the T0_DPLL_LOCKED_DAMPING[2:0] bits respectively. The corresponding bandwidth and damping factor are used when the T0 DPLL operates in different DPLL locking stages: starting, acquisition and locked, as controlled by the device automatically. Only the locked bandwidth and damping factor can be used regardless of the T0 DPLL locking stage, as controlled by the AUTO_BW_SEL bit. The device automatically controls the T0 DPLL to exit from TempHoldover mode. 3.10.1.4 Lost-Phase Mode In Lost-Phase mode, the T0 DPLL output attempts to track the selected input clock. The Lost-Phase mode is a secondary, temporary mode. 3.10.1.5 Holdover Mode In Holdover mode, the T0 DPLL resorts to the stored frequency data acquired in Locked mode to control its output. The T0 DPLL output is not Functional Description 34 June 19, 2006 IDT82V3280 WAN PLL phase locked to any input clock. The frequency offset acquiring method is selected by the MAN_HOLDOVER bit, the AUTO_AVG bit and the FAST_AVG bit, as shown in Table 19: Table 19: Frequency Offset Control in Holdover Mode MAN_HOLDOVER 0 1 AUTO_AVG 0 1 don't-care FAST_AVG don't-care 0 1 Frequency Offset Acquiring Method Automatic Instantaneous Automatic Slow Averaged Automatic Fast Averaged Manual 3.10.1.5.1 Automatic Instantaneous By this method, the T0 DPLL freezes at the operating frequency when it enters Holdover mode. The accuracy is 4.4X10-8 ppm. 3.10.1.5.2 Automatic Slow Averaged By this method, an internal IIR (Infinite Impulse Response) filter is employed to get the frequency offset. The IIR filter gives a 3 dB attenuation point corresponding to a period of 110 minutes. The accuracy is 1.1X10-5 ppm. 3.10.1.5.3 Automatic Fast Averaged By this method, an internal IIR (Infinite Impulse Response) filter is employed to get the frequency offset. The IIR filter gives a 3 dB attenuation point corresponding to a period of 8 minutes. The accuracy is 1.1X10-5 ppm. 3.10.1.5.4 Manual By this method, the frequency offset is set by T0_HOLDOVER_FREQ[23:0] bits. The accuracy is 1.1X10-5 ppm. the Table 20: Holdover Frequency Offset Read READ_AVG FAST_AVG 0 1 Offset Value Read from T0_HOLDOVER_FREQ[23:0] don't-care The value is equal to the one written to. The value is acquired by Automatic Slow Averaged 0 method, not equal to the one written to. The value is acquired by Automatic Fast Averaged 1 method, not equal to the one written to. The frequency offset in ppm is calculated as follows: Holdover Frequency Offset (ppm) = T0_HOLDOVER_FREQ[23:0] X 0.000011 3.10.1.6 Pre-Locked2 Mode In Pre-Locked2 mode, the T0 DPLL output attempts to track the selected input clock. The Pre-Locked2 mode is a secondary, temporary mode. 3.10.2 3.10.2.1 T4 DPLL OPERATING MODE Free-Run Mode The T4 path is simpler compared with the T0 path. In Free-Run mode, the T4 DPLL output refers to the master clock and is affected by any input clock. The accuracy of the T4 DPLL output is equal to that of the master clock. 3.10.2.2 Locked Mode In Locked mode, the T4 selected input clock may be locked in the T4 DPLL. When the T4 selected input clock is locked, the phase and frequency offset of the T4 DPLL output track those of the T4 selected input clock; when unlocked, the phase and frequency offset of the T4 DPLL output attempt to track those of the selected input clock. The T4 DPLL loop is closed in Locked mode. Its bandwidth and damping factor are set by the T4_DPLL_LOCKED_BW[1:0] bits and the T4_DPLL_LOCKED_DAMPING[2:0] bits respectively. 3.10.2.3 Holdover Mode In Holdover mode, the T4 DPLL resorts to the stored frequency data acquired in Locked mode to control its output. The T4 DPLL output is not The frequency offset of the T0 DPLL output is indicated by the CURRENT_DPLL_FREQ[23:0] bits. The device provides a reference for the value to be written to the T0_HOLDOVER_FREQ[23:0] bits. The value to be written can refer to the value read from the CURRENT_DPLL_FREQ[23:0] bits or the T0_HOLDOVER_FREQ[23:0] bits (refer to Chapter 3.10.1.5.5 Holdover Frequency Offset Read); or then be processed by external software filtering. 3.10.1.5.5 Holdover Frequency Offset Read The offset value, which is acquired by Automatic Slow Averaged, Automatic Fast Averaged and is set by related register bits, can be read from the T0_HOLDOVER_FREQ[23:0] bits by setting the READ_AVG bit and the FAST_AVG bit, as shown in Table 20. Functional Description 35 June 19, 2006 IDT82V3280 WAN PLL phase locked to any input clock. The T4 DPLL freezes at the operating frequency when it enters Holdover mode. The accuracy is 4.4X10-8 ppm. Table 21: Related Bit / Register in Chapter 3.10 Bit CURRENT_PH_DATA[15:0] CURRENT_DPLL_FREQ[23:0] T0_DPLL_START_BW[4:0] T0_DPLL_START_DAMPING[2:0] T0_DPLL_ACQ_BW[4:0] T0_DPLL_ACQ_DAMPING[2:0] T0_DPLL_LOCKED_BW[4:0] T0_DPLL_LOCKED_DAMPING[2:0] AUTO_BW_SEL FAST_LOS_SW TEMP_HOLDOVER_MODE[1:0] MAN_HOLDOVER AUTO_AVG FAST_AVG READ_AVG T0_HOLDOVER_FREQ[23:0] T4_DPLL_LOCKED_BW[1:0] T4_DPLL_LOCKED_DAMPING[2:0] T4_T0_SEL Register CURRENT_DPLL_PHASE[15:8]_STS, CURRENT_DPLL_PHASE[7:0]_STS CURRENT_DPLL_FREQ[23:16]_STS, CURRENT_DPLL_FREQ[15:8]_STS, CURRENT_DPLL_FREQ[7:0]_STS T0_DPLL_START_BW_DAMPING_CNFG T0_DPLL_ACQ_BW_DAMPING_CNFG T0_DPLL_LOCKED_BW_DAMPING_CNFG T0_BW_OVERSHOOT_CNFG PHASE_LOSS_FINE_LIMIT_CNFG Address (Hex) 69 *, 68 * 64 *, 63 *, 62 * 56 57 58 59 5B * T0_HOLDOVER_MODE_CNFG 5C T0_HOLDOVER_FREQ[23:16]_CNFG, T0_HOLDOVER_FREQ[15:8]_CNFG, T0_HOLDOVER_FREQ[7:0]_CNFG T4_DPLL_LOCKED_BW_DAMPING_CNFG T4_T0_REG_SEL_CNFG 5F, 5E, 5D 61 07 Note: * The setting in the 5B, 62 ~ 64, 68 and 69 registers is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit. Functional Description 36 June 19, 2006 IDT82V3280 WAN PLL 3.11 T0 / T4 DPLL OUTPUT The DPLL output is locked to the selected input clock. According to the phase-compared result of the feedback and the selected input clock, and the DPLL output frequency offset, the PFD output is limited and the DPLL output is frequency offset limited. 3.11.1 PFD OUTPUT LIMIT The PFD output is limited to be within 1 UI or within the coarse phase limit (refer to Chapter 3.7.1.2 Coarse Phase Loss), as determined by the MULTI_PH_APP bit. 3.11.2 FREQUENCY OFFSET LIMIT The DPLL output is limited to be within the DPLL hard limit (refer to Chapter 3.7.1.4 Hard Limit Exceeding). For T0 DPLL, the integral path value can be frozen when the DPLL hard limit is reached. This function, enabled by the T0_LIMT bit, will minimize the subsequent overshoot when T0 DPLL is pulling in. 3.11.3 PBO (T0 ONLY) The PBO function is only supported by the T0 path. When a PBO event is triggered, the phase offset of the selected input clock with respect to the T0 DPLL output is measured. The device then automatically accounts for the measured phase offset and compensates an appropriate phase offset into the DPLL output so that the phase transients on the T0 DPLL output are minimized. A PBO event is triggered if any one of the following conditions occurs: * T0 selected input clock switches (the PBO_EN bit is `1'); * T0 DPLL exits from Holdover mode or Free-Run mode (the PBO_EN bit is `1'); * Phase-time changes on the T0 selected input clock are greater than a programmable limit over an interval of less than 0.1 seconds (the PH_MON_PBO_EN bit is `1'). For the first two conditions, the phase transients on the T0 DPLL output are minimized to be no more than 0.61 ns with PBO. The PBO can also be frozen at the current phase offset by setting the PBO_FREZ bit. When the PBO is frozen, the device will ignore any further PBO events triggered by the above two conditions, and maintain the current phase offset. When the PBO is disabled, there may be a phase shift on the T0 DPLL output and the T0 DPLL output tracks back to 0 degree phase offset with respect to the T0 selected input clock. The last condition is specially for stratum 2 and 3E clocks. The PBO requirement specified in the Telcordia GR-1244-CORE is: `Input phasetime changes of 3.5 s or greater over an interval of less than 0.1 seconds or less shall be built-out by stratum 2 and 3E clocks to reduce the resulting clock phase-time change to less than 50 ns. Phase-time changes of 1.0 s or less over an interval of 0.1 seconds shall not be built-out.' Based on this requirement, phase-time changes of more than 1.0 s but less than 3.5 s that occur over an interval of less than 0.1 seconds may or may not be built-out. An integrated Phase Transient Monitor can be enabled by the PH_MON_EN bit to monitor the phase-time changes on the T0 selected input clock. When the phase-time changes are greater than a limit over an interval of less than 0.1 seconds, a PBO event is triggered and the phase transients on the DPLL output are absorbed. The limit is programmed by the PH_TR_MON_LIMT[3:0] bits, and can be calculated as follows: Limit (ns) = (PH_TR_MON_LIMT[3:0] + 7) X 156 The phase offset induced by PBO will never result in a coarse or fine phase loss. 3.11.4 PHASE OFFSET SELECTION (T0 ONLY) The phase offset of the T0 selected input clock with respect to the T0 DPLL output can be adjusted. If the device is configured as the Master, the PH_OFFSET_EN bit determines whether the input-to-output phase offset is enabled; if the device is configured as the Slave, the input-tooutput phase offset is always enabled. If enabled, the input-to-output phase offset can be adjusted by setting the PH_OFFSET[9:0] bits. The input-to-output phase offset can be calculated as follows: Phase Offset (ns) = PH_OFFSET[9:0] X 0.61 3.11.5 FOUR PATHS OF T0 / T4 DPLL OUTPUTS The T0 DPLL output and the T4 DPLL output are phase aligned with the T0 selected input clock and the T4 selected input clock respectively every 125 s period. Each DPLL has four output paths. 3.11.5.1 T0 Path The four paths for T0 DPLL output are as follows: * 77.76 MHz path - outputs a 77.76 MHz clock; * 16E1/16T1 path - outputs a 16E1 or 16T1 clock, as selected by the IN_SONET_SDH bit; * GSM/OBSAI/16E1/16T1 path - outputs a GSM, OBSAI, 16E1 or 16T1 clock, as selected by the T0_GSM_OBSAI_16E1_16T1_ SEL[1:0] bits; * 12E1/24T1/E3/T3 path - outputs a 12E1, 24T1, E3 or T3 clock, as selected by the T0_12E1_24T1_E3_T3_SEL[1:0] bits. T0 selected input clock is compared with a T0 DPLL output for DPLL locking. The output can only be derived from the 77.76 MHz path or the 16E1/16T1 path. The output path is automatically selected and the output is automatically divided to get the same frequency as the T0 selected input clock. The T0 DPLL 77.76 MHz output or an 8 kHz signal derived from it can be provided for the T4 DPLL input clock selection (refer to Chapter 3.6 T0 / T4 DPLL Input Clock Selection). T0 DPLL outputs are provided for T0/T4 APLL or device output process. Functional Description 37 June 19, 2006 IDT82V3280 WAN PLL 3.11.5.2 T4 Path The four paths for T4 DPLL output are as follows: * 77.76 MHz path - outputs a 77.76 MHz clock; * 16E1/16T1 path - outputs a 16E1 or 16T1 clock, as selected by the IN_SONET_SDH bit; * GSM/GPS/16E1/16T1 path - outputs a GSM, GPS, 16E1 or 16T1 clock, as selected by the T4_GSM_GPS_16E1_16T1_ SEL[1:0] bits; * 12E1/24T1/E3/T3 path - outputs a 12E1, 24T1, E3 or T3 clock, as selected by the T4_12E1_24T1_E3_T3_SEL[1:0] bits. T4 selected input clock is compared with a T4 DPLL output for DPLL locking. The output can be derived from the 77.76 MHz path or the Table 22: Related Bit / Register in Chapter 3.11 Bit MULTI_PH_APP T0_LIMT PBO_EN PBO_FREZ PH_MON_PBO_EN PH_MON_EN PH_TR_MON_LIMT[3:0] PH_OFFSET_EN PH_OFFSET[9:0] IN_SONET_SDH T0_GSM_OBSAI_16E1_16T1_SEL[1:0] T0_12E1_24T1_E3_T3_SEL[1:0] T4_GSM_GPS_16E1_16T1_SEL[1:0] T4_12E1_24T1_E3_T3_SEL[1:0] T4_TEST_T0_PH T4_T0_SEL 16E1/16T1 path. In this case, the output path is automatically selected and the output is automatically divided to get the same frequency as the T4 selected input clock. In addition, T4 selected input clock is compared with the T0 selected input clock to get the phase difference between T0 and T4 selected input clocks, as determined by the T4_TEST_T0_PH bit. T4 DPLL outputs are provided for T0/T4 APLL or device output process. Register PHASE_LOSS_COARSE_LIMIT_CNFG T0_BW_OVERSHOOT_CNFG MON_SW_PBO_CNFG PHASE_MON_PBO_CNFG PHASE_OFFSET[9:8]_CNFG PHASE_OFFSET[9:8]_CNFG, PHASE_OFFSET[7:0]_CNFG INPUT_MODE_CNFG T0_DPLL_APLL_PATH_CNFG T4_DPLL_APLL_PATH_CNFG T4_INPUT_SEL_CNFG T4_T0_REG_SEL_CNFG Address (Hex) 5A * 59 0B 78 7B 7B, 7A 09 55 60 51 07 Note: * The setting in the 5A register is either for T0 path or for T4 path, as determined by the T4_T0_SEL bit. Functional Description 38 June 19, 2006 IDT82V3280 WAN PLL 3.12 T0 / T4 APLL A T0 APLL and a T4 APLL are provided for a better jitter and wander performance of the device output clocks. The bandwidths of the T0/T4 APLL are set by the T0_APLL_BW[1:0] / T4_APLL_BW[1:0] bits respectively. The lower the bandwidth is, the better the jitter and wander performance of the T0/T4 APLL output are. The input of the T0/T4 APLL can be derived from one of the T0 and T4 DPLL outputs, as selected by the T0_APLL_PATH[3:0] / T4_APLL_PATH[3:0] bits respectively. Both the APLL and DPLL outputs are provided for selection for the device output. Table 23: Related Bit / Register in Chapter 3.12 Bit T0_APLL_BW[1:0] T4_APLL_BW[1:0] T0_APLL_PATH[3:0] T4_APLL_PATH[3:0] Register T0_T4_APLL_BW_CNFG T0_DPLL_APLL_PATH_CNFG T4_DPLL_APLL_PATH_CNFG Address (Hex) 6A 55 60 OUT6 and OUT7 output a PECL or LVDS signal, as selected by the OUT6_PECL_LVDS bit and the OUT7_PECL_LVDS bit respectively. OUT8 outputs an AMI signal. The outputs on OUT1 ~ OUT7 are variable, depending on the signals derived from the T0/T4 DPLL and T0/T4 APLL outputs, and the corresponding OUTn_PATH_SEL[3:0] bits (1 n 7). The derived signal can be from the T0/T4 DPLL and T0/T4 APLL outputs, as selected by the corresponding OUTn_PATH_SEL[3:0] bits (1 n 7). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the output frequency. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the output frequency. The output on OUT8 is derived from T0 or T4 DPLL 77.76 MHz path, as selected by the OUT8_PATH_SEL bit. After being divided automatically, the output is of 64 kHz + 8 kHz or 64 kHz + 8 kHz + 0.4 kHz, as selected by the 400HZ_SEL bit. Its duty cycle is 50:50 or 5:8, as determined by the AMI_OUT_DUTY bit. The output on OUT9 is derived from T0 or T4 DPLL 16E1/16T1 path, as selected by the OUT9_PATH_SEL bit. After being divided automatically, the output is of 2.048 MHz or 1.544 MHz, as selected by the IN_SONET_SDH bit. The outputs on OUT8 and OUT9 can be enabled or disabled, or may be affected by the status of the T4 input clock. It is determined by the OUT8_EN / OUT9_EN and T4_INPUT_FAIL 1 / T4_INPUT_FAIL 2 bits. Refer to Table 26. The outputs on OUT1 to OUT7 and OUT9 can be inverted, as determined by the corresponding OUTn_INV bit (1 n 7 or n = 9). All the output clocks derived from T0/T4 selected input clock are aligned with the T0/T4 selected input clock respectively every 125 s period. 3.13 OUTPUT CLOCKS & FRAME SYNC SIGNALS The device supports 9 output clocks and 2 frame sync output signals altogether. 3.13.1 OUTPUT CLOCKS The device provides 9 output clocks. According to the output port technology, the output ports support the following technologies: * AMI; * PECL/LVDS; * CMOS. OUT1 ~ OUT5 and OUT9 output a CMOS signal. Functional Description 39 June 19, 2006 IDT82V3280 WAN PLL Table 24: Outputs on OUT1 ~ OUT7 if Derived from T0/T4 DPLL Outputs OUTn_DIVIDER[3:0] (Output Divider) 1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 outputs on OUT1 ~ OUT7 if derived from T0/T4 DPLL outputs 2 77.76 MHz 12E1 16E1 24T1 16T1 E3 T3 GSM (26 MHz) OBSAI (30.72 MHz) GPS (40 MHz) Output is disabled (output low). 12E1 6E1 3E1 2E1 E1 E1 T1 64 kHz 8 kHz 2 kHz 400 Hz 1Hz Output is disabled (output high). 16E1 8E1 4E1 2E1 24T1 12T1 6T1 4T1 3T1 2T1 16T1 8T1 4T1 2T1 T1 E3 T3 13 MHz 15.36 MHz 20 10 5 Note: 1. 1 n 7. Each output is assigned a frequency divider. 2. E1 = 2.048 MHz, T1 = 1.544 MHz, E3 = 34.368 MHz, T3 = 44.736 MHz. The blank cell means the configuration is reserved. Functional Description 40 June 19, 2006 IDT82V3280 WAN PLL Table 25: Outputs on OUT1 ~ OUT7 if Derived from T0/T4 APLL OUTn_DIVIDER[3:0] (Output Divider) 1 77.76 MHz X 4 12E1 X 4 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 6.48 MHz E1 E1 T1 Output is disabled (output high). 622.08 MHz 3 outputs on OUT1 ~ OUT7 if derived from T0/T4 APLL output 2 16E1 X 4 24T1 X 4 16T1 X 4 E3 T3 GSM OBSAI (26 MHz X 2) (30.72 MHz X 10) GPS (40 MHz) Output is disabled (output low). 311.04 MHz 3 155.52 MHz 77.76 MHz 51.84 MHz 38.88 MHz 25.92 MHz 19.44 MHz 48E1 24E1 12E1 8E1 6E1 4E1 3E1 2E1 2E1 64E1 32E1 16E1 8E1 4E1 96T1 48T1 24T1 16T1 12T1 8T1 6T1 4T1 3T1 2T1 T1 2T1 64T1 32T1 16T1 8T1 4T1 61.44 MHz 4 30.72 MHz 4 15.36 MHz 4 7.68 MHz 4 3.84 MHz 4 E3 T3 52 MHz 26 MHz 13 MHz 153.6 MHz 76.8 MHz 38.4 MHz 20 MHz 10 MHz 5 MHz Note: 1. 1 n 7. Each output is assigned a frequency divider. 2. In the APLL, the selected T0/T4 DPLL output may be multiplied. E1 = 2.048 MHz, T1 = 1.544 MHz, E3 = 34.368 MHz, T3 = 44.736 MHz. The blank cell means the configuration is reserved. 3. The 622.08 MHz and 311.04 MHz differential signals are only output on OUT6 and OUT7. 4. The 61.44 MHz, 30.72 MHz, 15.36 MHz, 7.68 MHz and 3.84 MHz outputs are only derived from T0 APLL. Table 26: Outputs on OUT8 & OUT9 OUT8_EN / OUT9_EN T4_INPUT_FAIL 1 / T4_INPUT_FAIL 2 0 1 don't-care 0 1 Outputs on OUT8 & OUT9 Output is disabled (output low). Output is enabled. Output is enabled when the T4 selected input clock does not fail. Output is disabled (output low) when the T4 selected input clock fails. Functional Description 41 June 19, 2006 IDT82V3280 WAN PLL 3.13.2 FRAME SYNC OUTPUT SIGNALS An 8 kHz and a 2 kHz frame sync signals are output on the FRSYNC_8K and MFRSYNC_2K pins if enabled by the 8K_EN and 2K_EN bits respectively. They are CMOS outputs. The two frame sync signals are derived from the T0 APLL output and are aligned with the output clock. They can be synchronized to the frame sync input signal. If the frame sync input signal with respect to the T0 selected input clock is above a limit set by the SYNC_MON_LIMT[2:0] bits, an external sync alarm will be raised and EX_SYNC1 is disabled to synchronize the frame sync output signals. The external sync alarm is cleared once EX_SYNC1 with respect to the T0 selected input clock is within the limit. If it is within the limit, whether EX_SYNC1 is enabled to synchronize the frame sync output signal is determined by the AUTO_EXT_SYNC_EN bit and the EXT_SYNC_EN bit. Refer to Table 27 for details. When the frame sync input signal is enabled to synchronize the frame sync output signal, it should be adjusted to align itself with the T0 Table 27: Synchronization Control AUTO_EXT_SYNC_EN EXT_SYNC_EN don't-care 0 1 0 1 1 selected input clock. Nominally, the falling edge of EX_SYNC1 is aligned with the rising edge of the T0 selected input clock. EX_SYNC1 may be 0.5 UI early/late or 1 UI late due to the circuit and board wiring delays. Setting the sampling of EX_SYNC1 by the SYNC_PH1[1:0] bits will compensate this early/late. Refer to Figure 9 to Figure 12. The EX_SYNC_ALARM_MON bit indicates whether EX_SYNC1 is in external sync alarm status. The external sync alarm is indicated by the EX_SYNC_ALARM 1 bit. If the EX_SYNC_ALARM 2 bit is `1', the occurrence of the external sync alarm will trigger an interrupt. The 8 kHz and the 2 kHz frame sync output signals can be inverted by setting the 8K_INV and 2K_INV bits respectively. The frame sync outputs can be 50:50 duty cycle or pulsed, as determined by the 8K_PUL and 2K_PUL bits respectively. When they are pulsed, the pulse width is defined by the period of OUT3; and they are pulsed on the position of the falling or rising edge of the standard 50:50 duty cycle, as selected by the 2K_8K_PUL_POSITION bit. Synchronization Disabled Enabled Enabled if the T0 selected input clock is IN11; otherwise, disabled. T0 selected input clock EX_SYNC1 Frame sync output signals Output clocks T0 selected input clock EX_SYNC1 Frame sync output signals Output clocks Figure 9. On Target Frame Sync Input Signal Timing Figure 10. 0.5 UI Early Frame Sync Input Signal Timing Functional Description 42 June 19, 2006 IDT82V3280 WAN PLL T0 selected input clock EX_SYNC1 Frame sync output signals Output clocks T0 selected input clock EX_SYNC1 Frame sync output signals Output clocks Figure 11. 0.5 UI Late Frame Sync Input Signal Timing Table 28: Related Bit / Register in Chapter 3.13 Bit OUT6_PECL_LVDS OUT7_PECL_LVDS OUTn_PATH_SEL[3:0] (1 n 7) OUTn_DIVIDER[3:0] (1 n 7) OUT8_PATH_SEL 400HZ_SEL AMI_OUT_DUTY T4_INPUT_FAIL OUT8_EN OUT9_PATH_SEL OUT9_EN T4_INPUT_FAIL 2 IN_SONET_SDH AUTO_EXT_SYNC_EN EXT_SYNC_EN OUTn_INV (1 n 7 or n = 9) 8K_EN 2K_EN 8K_INV 2K_INV 8K_PUL 2K_PUL 2K_8K_PUL_POSITION SYNC_MON_LIMT[2:0] 1 Figure 12. 1 UI Late Frame Sync Input Signal Timing Register DIFFERENTIAL_IN_OUT_OSCI_CNFG OUT1_FREQ_CNFG ~ OUT7_FREQ_CNFG Address (Hex) 0A 6B ~ 71 OUT8_FREQ_CNFG 72 OUT9_FREQ_CNFG 73 INPUT_MODE_CNFG OUT9_FREQ_CNFG, OUT8_FREQ_CNFG 09 73, 72 FR_MFR_SYNC_CNFG 74 SYNC_PH1[1:0] EX_SYNC_ALARM_MON EX_SYNC_ALARM 1 EX_SYNC_ALARM 2 SYNC_MONITOR_CNFG SYNC_PHASE_CNFG OPERATING_STS INTERRUPTS3_STS INTERRUPTS3_ENABLE_CNFG 7C 7D 52 0F 12 Functional Description 43 June 19, 2006 IDT82V3280 WAN PLL 3.14 MASTER / SLAVE CONFIGURATION Master / Slave configuration is only supported by the T0 path of the device. Two devices should be used together in order to: * Enable system protection against single chip failure; * Guarantee no service interrupt during system maintenance, such as software or hardware upgrade. Of the two devices, one is configured as the Master and the other is configured as the Slave. The configuration is made by the MS/SL pin and the MS_SL_CTRL bit (b0, 13H), as shown in Table 29: Table 29: Device Master / Slave Control Master / Slave Control MS/SL pin High Low MS_SL_CTRL Bit 0 1 0 1 Result Master Slave Slave Master In this application, all the output clocks derived from the T0 selected input clock and the frame sync output signals from the two devices are at the same frequency offset and phase. Refer to Chapter 3.13.2 Frame SYNC Output Signals for details. The difference between the Master and the Slave is: in the Master, the IN11 should not be selected by the T0 DPLL; in the Slave, the following functions are automatically forced: * The T0 selected input clock is IN11; * T0 PBO is disabled; * T0 DPLL operates at the acquisition bandwidth and damping factor; * EX_SYNC1 is used for synchronization; * T0 DPLL operates in Locked mode. In the Slave, the corresponding registers of the above forced functions can still be configured, but their configuration does not take any effect. The frequency of the T0 selected input clock IN11 is recommended to be 6.48 MHz. Backplane connections Hardware control . . . EX_SYNC1 MS/SL IN1 . . . OUT1 one output OUT2 . clock . . . . . IN10 IN11 IN12 . IN14 . . Chip A OUT7 one output FRSYNC_8K/ frame sync MFRSYNC_2K signal . . . . . . EX_SYNC1 MS/SL IN1 . . . . . . IN10 IN11 IN12 . . . Chip B OUT1 OUT2 one output . clock . OUT7 . . . . IN14 one output FRSYNC_8K/ frame sync MFRSYNC_2K signal Backplane Backplane Figure 13. Physical Connection Between Two Devices Functional Description 44 June 19, 2006 IDT82V3280 WAN PLL 3.15 INTERRUPT SUMMARY 3.16 T0 AND T4 SUMMARY The interrupt sources of the device are as follows: * AMI violation * LOS * T4 DPLL locking status change * Input clocks for T0 path validity change * T0 selected input clock fail * Input clocks for T4 path change to be no qualified input clock available * T0 DPLL operating mode switch * External sync alarm All of the above interrupt events are indicated by the corresponding interrupt status bit. If the corresponding interrupt enable bit is set, any of the interrupts can be reported by the INT_REQ pin. The output characteristics on the INT_REQ pin are determined by the HZ_EN bit and the INT_POL bit. Interrupt events are cleared by writing a `1' to the corresponding interrupt status bit. The INT_REQ pin will be inactive only when all the pending enabled interrupts are cleared. In addition, the interrupt of T0 selected input clock fail can be reported by the TDO pin, as determined by the LOS_FLAG_TO_TDO bit. Table 30: Related Bit / Register in Chapter 3.15 Bit HZ_EN INT_POL LOS_FLAG_TO_TDO Register INTERRUPT_CNFG MON_SW_PBO_CNFG Address (Hex) 0C 0B The main features supported by the T0 path are as follows: * Phase lock alarm; * Forced or Automatic input clock selection/switch; * 3 primary and 3 secondary, temporary DPLL operating modes, switched automatically or under external control; * Automatic switch between starting, acquisition and locked bandwidths/damping factors; * Programmable DPLL bandwidths from 0.5 mHz to 560 Hz in 19 steps; * Programmable damping factors: 1.2, 2.5, 5, 10 and 20; * Fast loss, coarse phase loss, fine phase loss and hard limit exceeding monitoring; * Output phase and frequency offset limited; * Automatic Instantaneous, Automatic Slow Averaged, Automatic Fast Averaged or Manual holdover frequency offset acquiring; * PBO to minimize output phase transients; * Programmable output phase offset; * Low jitter multiple clock outputs with programmable polarity; * Low jitter 2 kHz and 8 kHz frame sync signal outputs with programmable pulse width and polarity; * Master / Slave application to enable system protection against single device failure. The main features supported by the T4 path are as follows: * Forced or Automatic input clock selection/switch; * Locking to T0 DPLL output; * 3 DPLL operating modes, switched automatically or under external control; * Programmable DPLL bandwidth: 18 Hz, 35 Hz, 70 Hz and 560 Hz; * Programmable damping factor: 1.2, 2.5, 5, 10 and 20; * Fast loss, coarse phase loss, fine phase loss and hard limit exceeding monitoring; * Output phase and frequency offset limited; * Automatic Instantaneous holdover frequency offset; * Low jitter multiple clock outputs with programmable polarity. Functional Description 45 June 19, 2006 IDT82V3280 WAN PLL 3.17 POWER SUPPLY FILTERING TECHNIQUES 3.3V SLF7028T-100M1R1 10 F 0.1 F 0.1 F 0.1 F 0.1 F IDT82V3280 VDDA 0.1 F 6, 19, 91 1, 5, 20, 92 11, 14, 15, 62, 84, 87 33, 39 VDD_DIFF 29 32, 38 AGND DGND GND_AMI GND_DIFF 3.3V SLF7028T-100M1R1 10 F 0.1 F 0.1 F 0.1 F 0.1 F 0.1 F 0.1 F 0.1 F 0.1 F VDD_AMI 26 VDDD 12, 13, 16, 50, 61, 85, 86 Figure 14. IDT82V3280 Power Decoupling Scheme To achieve optimum jitter performance, power supply filtering is required to minimize supply noise modulation of the output clocks. The common sources of power supply noise are switch power supplies and the high switching noise from the outputs to the internal PLL. The 82V3280 provides separate VDDA power pins for the internal analog PLL, VDD_DIFF for the differential output driver circuit and VDDD pins for the core logic as well as I/O driver circuits. To minimize switching power supply noise generated by the switching regulator, the power supply output should be filtering with sufficient bulk capacity to minimize ripple and 0.1 uF (0402 case size, ceramic) caps to filter out the switching transients. For the 82V3280, the decoupling for VDDA, VDD_DIFF, VDD_AMI and VDDD are handled individually. VDDD, VDD_AMI, VDD_DIFF and VDDA should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. Figure 14 illustrated how bypass capacitor and ferrite bead should be connected to power pins. The analog power supply VDDA and VDD_DIFF should have low impedance. This can be achieved by using one 10 uF (1210 case size, ceramic) and at least four 0.1 uF (0402 case size, ceramic) capacitors in parallel. The 0.1 uF (0402 case size, ceramic) capacitors must be placed right next to the VDDA and VDD_DIFF pins as close as possible. Note that the 10 uF capacitor must be of 1210 case size, and it must be ceramic for lowest ESR (Effective Series Resistance) possible. The 0.1 uF should be of case size 0402, this offers the lowest ESL (Effective Series Inductance) to achieve low impedance towards the high speed range. For VDDD and VDD_AMI, at least ten 0.1 uF (0402 case size, ceramic) and one 10 uF (1210 case size, ceramic) capacitors are recommended. The 0.1 uF capacitors should be placed as close to the VDDD pins as possible. Please refer to evaluation board schematic for details. Functional Description 46 June 19, 2006 IDT82V3280 WAN PLL 4 TYPICAL APPLICATION The device supports Master / Slave application, as shown in Figure 15: PRS (Primary Reference Source) BITS/SSU Timing Module Stratum 2/3E IDT82V3288 Typical 8 kHz/1.544 MHz/2.048 MHz BITS/SSU Timing Module Stratum 2/3E IDT82V3288 Line Timing Typical 19.44 MHz and other OC-N clock Stratum 2/3E/3/SMC/SEC Module IDT82V3280 Master/Slave Stratum 2/3E/3/SMC/SEC Module IDT82V3280 Line Timing Typical 19.44 MHz and other OC-N clock Central Clock Modules Typical 19.44 MHz and other OC-N clock Typical 19.44 MHz and other OC-N clock SDH/SONET or other Equipment Timing System 155.52 Mbit/s Line Card IDT82V3255 622.08 Mbit/s Line Card IDT82V3255 2.5 Gbit/s Line Card IDT82V3255 10 Gbit/s Line Card IDT82V3255 ... ... Figure 15. Typical Application 4.1 MASTER / SLAVE APPLICATION Master / Slave application is only supported by the T0 path of the device. In Master / Slave application, two devices should be used together. Of the two devices, one is configured as the Master and the other is configured as the Slave. Refer to Chapter 3.14 Master / Slave Configuration for details. Typical Application 47 June 19, 2006 IDT82V3280 WAN PLL 5 MICROPROCESSOR INTERFACE The microprocessor interface provides access to read and write the registers in the device. The microprocessor interface supports the following five modes: * EPROM mode; * Multiplexed mode; * Intel mode; * Motorola mode; * Serial mode. The microprocessor interface mode is selected by the MPU_SEL_CNFG[2:0] bits (b2~0, 7FH). The interface pins in different interface modes are listed in Table 31: Table 31: Microprocessor Interface MPU_SEL_CNFG[2:0] bits 001 010 011 100 101 Microprocessor Interface Mode ERPOM Multiplexed Intel Motorola Serial Interface Pins CS, A[6:0], AD[7:0] CS, ALE, WR, RD, AD[7:0], RDY CS, WR, RD, A[6:0], AD[7:0], RDY CS, WR, A[6:0], AD[7:0], RDY CS, SCLK, SDI, SDO, CLKE Microprocessor Interface 48 June 19, 2006 IDT82V3280 WAN PLL 5.1 EPROM MODE In this mode, the device is used with an EPROM. The configuration data will be automatically read from the EPROM after the device is powered on. CS A[6:0] tacc AD[7:0] High-Z address data High-Z Figure 16. EPROM Access Timing Diagram Table 32: Access Timing Characteristics in EPROM Mode Symbol tacc Parameter Min Typ Max 920 Unit ns CS to valid data delay time Microprocessor Interface 49 June 19, 2006 IDT82V3280 WAN PLL 5.2 MULTIPLEXED MODE tpw3 ALE tsu1 CS tsu2 WR RD td1 AD[7:0] address td2 tpw2 data th3 td5 td6 Figure 17. Multiplexed Read Timing Diagram tT th1 tpw1 th2 td4 RDY High-Z High-Z Table 33: Read Timing Characteristics in Multiplexed Mode Symbol T tin tout tsu1 tsu2 td1 td2 td4 td5 td6 tpw1 tpw2 tpw3 th1 th2 th3 tT tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid address to ALE falling edge setup time Valid CS to Valid RD setup time Valid RD to valid data delay time Valid CS to valid RDY delay time 13 10 13 13 4.5T + 10 * 4.5T + 10 2 3 0 0 0 >T 2 0 3.5T + 10 Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns RD rising edge to AD[7:0] high impedance delay time RD rising edge to RDY low delay time CS rising edge to RDY release delay time Valid RD pulse width low Valid RDY pulse width low Valid ALE pulse width high Valid address after ALE falling edge hold time Valid CS after RD rising edge hold time Valid RD after RDY rising edge hold time Time between ALE falling edge and RD falling edge Time between consecutive Read-Read or Read-Write accesses (RD rising edge to ALE rising edge) Note: * Timing with RDY. If RDY is not used, tpw1 is 3.5T + 10. Microprocessor Interface 50 June 19, 2006 IDT82V3280 WAN PLL tpw3 ALE tsu1 CS th1 tT RD WR tsu2 tpw1 th2 tsu3 AD[7:0] address td2 RDY High-Z tpw2 data th3 th4 td5 High-Z td6 Figure 18. Multiplexed Write Timing Diagram Table 34: Write Timing Characteristics in Multiplexed Mode Symbol T tin tout tsu1 tsu2 tsu3 td2 td5 td6 tpw1 tpw2 tpw3 th1 th2 th3 th4 tT tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid address to ALE falling edge setup time Valid CS to valid WR setup time Valid data to WR rising edge setup time Valid CS to valid RDY delay time 2 0 3 13 13 13 1.5T + 10 1.5T + 10 2 3 0 0 9 0 >7T Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns WR rising edge to RDY low delay time CS rising edge to RDY release delay time Valid WR pulse width low Valid RDY pulse width low Valid ALE pulse width high Valid address after ALE falling edge hold time Valid CS after WR rising edge hold time Valid WR after RDY rising edge hold time Valid data after WR rising edge hold time Time between ALE falling edge and WR falling edge Time between consecutive Write-Read or Write-Write accesses (WR rising edge to ALE rising edge) Microprocessor Interface 51 June 19, 2006 IDT82V3280 WAN PLL 5.3 INTEL MODE CS WR tsu2 RD tsu1 A[6:0] High-Z AD[7:0] td2 RDY High-Z td6 Figure 19. Intel Read Timing Diagram Table 35: Read Timing Characteristics in Intel Mode Symbol T tin tout tsu1 tsu2 td1 td2 td4 td5 td6 tpw1 tpw2 th1 th2 th3 tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid address to valid CS setup time Valid CS to valid RD setup time Valid RD to valid data delay time Valid CS to valid RDY delay time 13 10 13 13 4.5T + 10 * 4.5T + 10 0 0 0 >T 0 0 3.5T + 10 Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns tpw1 th2 th1 address td1 data tpw2 th3 td5 High-Z td4 High-Z RD rising edge to AD[7:0] high impedance delay time RD rising edge to RDY low delay time CS rising edge to RDY release delay time Valid RD pulse width low Valid RDY pulse width low Valid address after RD rising edge hold time Valid CS after RD rising edge hold time Valid RD after RDY rising edge hold time Time between consecutive Read-Read or Read-Write accesses (RD rising edge to RD falling edge, or RD rising edge to WR falling edge) Note: * Timing with RDY. If RDY is not used, tpw1 is 3.5T + 10. Microprocessor Interface 52 June 19, 2006 IDT82V3280 WAN PLL CS tsu2 WR tpw1 th2 RD tsu1 A[6:0] address tsu3 AD[7:0] td2 RDY High-Z td6 Figure 20. Intel Write Timing Diagram Table 36: Write Timing Characteristics in Intel Mode Symbol T tin tout tsu1 tsu2 tsu3 td2 td5 td6 tpw1 tpw2 th1 th2 th3 th4 tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid address to valid CS setup time Valid CS to valid WR setup time Valid data before WR rising edge setup time Valid CS to valid RDY delay time 0 0 3 13 13 13 1.5T + 10 1.5T + 10 0 0 0 9 >7T Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns th1 th4 data tpw2 th3 td5 High-Z WR rising edge to RDY low delay time CS rising edge to RDY release delay time Valid WR pulse width low Valid RDY pulse width low Valid address after WR rising edge hold time Valid CS after WR rising edge hold time Valid WR after RDY rising edge hold time Valid data after WR rising edge hold time Time between consecutive Write-Read or Write-Write accesses (WR rising edge to WR falling edge, or WR rising edge to RD falling edge) Microprocessor Interface 53 June 19, 2006 IDT82V3280 WAN PLL 5.4 MOTOROLA MODE CS tsu2 WR tsu1 A[6:0] AD[7:0] High-Z td2 RDY High-Z address td1 tpw1 th2 th1 td3 data tpw2 th3 td4 tr1 High-Z High-Z Figure 21. Motorola Read Timing Diagram Table 37: Read Timing Characteristics in Motorola Mode Symbol T tin tout tsu1 tsu2 td1 td2 td3 td4 tpw1 tpw2 th1 th2 th3 tr1 tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid address to valid CS setup time Valid WR to valid CS setup time Valid CS to valid data delay time Valid CS to valid RDY delay time 13 10 13 4.5T + 10 * 4.5T + 10 0 0 0 3 >T 0 0 3.5T + 10 Min Typ 12.86 5 5 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Max Unit CS rising edge to AD[7:0] high impedance delay time CS rising edge to RDY release delay time Valid CS pulse width low Valid RDY pulse width high Valid address after CS rising edge hold time Valid WR after CS rising edge hold time Valid CS after RDY falling edge hold time RDY release time Time between consecutive Read-Read or Read-Write accesses (CS rising edge to CS falling edge) Note: * Timing with RDY. If RDY is not used, tpw1 is 3.5T +10. Microprocessor Interface 54 June 19, 2006 IDT82V3280 WAN PLL tpw1 CS tsu2 WR tsu1 A[6:0] address tsu3 AD[7:0] td2 RDY High-Z Figure 22. Motorola Write Timing Diagram Table 38: Write Timing Characteristics in Motorola Mode Symbol T tin tout tsu1 tsu2 tsu3 td2 td4 tpw1 tpw2 th1 th2 th3 th4 tr1 tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid address to valid CS setup time Valid WR to valid CS setup time Valid data before CS rising edge setup time Valid CS to valid RDY delay time 0 0 3 13 13 1.5T + 10 1.5T + 10 0 0 0 9 3 > 7T Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns th2 th1 th4 data tpw2 th3 td4 tr1 High-Z CS rising edge to RDY release delay time Valid CS pulse width low Valid RDY pulse width high Valid address after valid CS rising edge hold time Valid WR after valid CS rising edge hold time Valid CS after RDY falling edge hold time Valid data after valid CS rising edge hold time RDY release time Time between consecutive Write-Write or Write-Read accesses (CS rising edge to CS falling edge) Microprocessor Interface 55 June 19, 2006 IDT82V3280 WAN PLL 5.5 SERIAL MODE In a read operation, the active edge of SCLK is selected by CLKE. When CLKE is asserted low, data on SDO will be clocked out on the ris- ing edge of SCLK. When CLKE is asserted high, data on SDO will be clocked out on the falling edge of SCLK. In a write operation, data on SDI will be clocked in on the rising edge of SCLK. CS tsu2 SCLK tsu1 SDI th1 tpw1 A0 A1 A2 A3 A4 A5 A6 tpw2 th2 R/W td1 SDO High-Z D0 D1 D2 D3 D4 D5 D6 td2 D7 Figure 23. Serial Read Timing Diagram (CLKE Asserted Low) CS th2 SCLK SDI R/W A0 A1 A2 A3 A4 A5 A6 td1 High-Z td2 D0 D1 D2 D3 D4 D5 D6 D7 SDO Figure 24. Serial Read Timing Diagram (CLKE Asserted High) Table 39: Read Timing Characteristics in Serial Mode Symbol T tin tout tsu1 tsu2 td1 td2 tpw1 tpw2 th1 th2 tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid SDI to valid SCLK setup time Valid CS to valid SCLK setup time Valid SCLK to valid data delay time 4 14 10 10 3.5T + 5 3.5T + 5 6 5 10 Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns ns ns CS rising edge to SDO high impedance delay time SCLK pulse width low SCLK pulse width high Valid SDI after valid SCLK hold time Valid CS after valid SCLK hold time (CLKE = 0/1) Time between consecutive Read-Read or Read-Write accesses (CS rising edge to CS falling edge) Microprocessor Interface 56 June 19, 2006 IDT82V3280 WAN PLL CS tsu2 SCLK tsu1 SDI SDO R/W A0 A1 A2 tpw2 th2 th1 tpw1 A3 A4 A5 A6 D0 D1 D2 D3 D4 D5 D6 D7 High-Z Figure 25. Serial Write Timing Diagram Table 40: Write Timing Characteristics in Serial Mode Symbol T tin tout tsu1 tsu2 tpw1 tpw2 th1 th2 tTI Parameter One cycle time of the master clock Delay of input pad Delay of output pad Valid SDI to valid SCLK setup time Valid CS to valid SCLK setup time SCLK pulse width low SCLK pulse width high Valid SDI after valid SCLK hold time Valid CS after valid SCLK hold time Time between consecutive Write-Write or Write-Read accesses (CS rising edge to CS falling edge) 4 14 3.5T 3.5T 6 5 10 Min Typ 12.86 5 5 Max Unit ns ns ns ns ns ns ns ns ns ns Microprocessor Interface 57 June 19, 2006 IDT82V3280 WAN PLL 6 JTAG This device is compliant with the IEEE 1149.1 Boundary Scan standard except the following: * The output boundary scan cells do not capture data from the core and the device does not support EXTEST instruction; * The TRST pin is set low by default and JTAG is disabled in order to be consistent with other manufacturers. The JTAG interface timing diagram is shown in Figure 26. tTCK TCK tS TMS TDI tH tD TDO Figure 26. JTAG Interface Timing Diagram Table 41: JTAG Timing Characteristics Symbol tTCK tS tH tD Parameter TCK period TMS / TDI to TCK setup time TCK to TMS / TDI Hold Time TCK to TDO delay time Min 100 25 25 50 Typ Max Unit ns ns ns ns JTAG 58 June 19, 2006 IDT82V3280 WAN PLL 7 PROGRAMMING INFORMATION The access of the Multi-word Registers is different from that of the Single-word Registers. Take the registers (04H, 05H and 06H) for an example, the write operation for the Multi-word Registers follows a fixed sequence. The register (04H) is configured first and the register (06H) is configured last. The three registers are configured continuously and should not be interrupted by any operation. The crystal calibration configuration will take effect after all the three registers are configured. During read operation, the register (04H) is read first and the register (06H) is read last. The crystal calibration reading should be continuous and not be interrupted by any operation. Certain bit locations within the device register map are designated as Reserved. To ensure proper and predictable operation, bits designated as Reserved should not be written by the users. In addition, their value should be masked out from any testing or error detection methods that are implemented. After reset, all the registers are set to their default values. The registers are read or written via the microprocessor interface. Before any write operation, the value in register PROTECTION_CNFG is recommended to be confirmed to make sure whether the write operation is enabled. The device provides 3 register protection modes: * Protected mode: no other registers can be written except register PROTECTION_CNFG itself; * Fully Unprotected mode: all the writable registers can be written; * Single Unprotected mode: one more register can be written besides register PROTECTION_CNFG. After write operation (not including writing a `1' to clear a bit to `0'), the device automatically switches to Protected mode. Writing `0' to the registers will take no effect if the registers are cleared by writing `1'. T0 and T4 paths share some registers, whose addresses are 26H ~ 2CH, 4EH, 4FH, 5AH, 5BH, 62H ~ 64H, 68H and 69H. The names of shared registers are marked with a *. Before register read/write operation, register T4_T0_REG_SEL_CNFG is recommended to be confirmed to make sure whether the register operation is available for T0 or T4 path. Table 42: Register List and Map Address (Hex) 00 01 02 04 Register Name Bit 7 Bit 6 Bit 5 7.1 REGISTER MAP Table 42 is the map of all the registers, sorted in an ascending order of their addresses. Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reference Page P 65 P 66 Global Control Registers ID[7:0] - Device ID 1 ID[15:8] - Device ID 2 MPU_PIN_STS - MPU_MODE[2:0] Pins Status NOMINAL_FREQ[7:0]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 1 NOMINAL_FREQ[15:8]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 2 NOMINAL_FREQ[23:16]_CNFG Crystal Oscillator Frequency Offset Calibration Configuration 3 T4_T0_REG_SEL_CNFG - T0 / T4 Registers Selection Configuration PHASE_ALARM_TIME_OUT_CNFG Phase Lock Alarm Time-Out Configuration ID[7:0] ID[15:8] MPU_PIN_STS[2:0] P 66 P 66 NOMINAL_FREQ_VALUE[7:0] 05 NOMINAL_FREQ_VALUE[15:8] P 66 06 07 08 NOMINAL_FREQ_VALUE[23:16] T4_T0_SE L - P 67 P 67 P 68 MULTI_FACTOR[1:0] TIME_OUT_VALUE[5:0] IN_SONET MASTER_ REVERTIV _SDH SLAVE E_MODE OSC_EDG OUT7_PE OUT6_PE E CL_LVDS CL_LVDS 09 0A PH_ALAR AUTO_EX EXT_SYN INPUT_MODE_CNFG - Input Mode M_TIMEO T_SYNC_ C_EN Configuration UT EN DIFFERENTIAL_IN_OUT_OSCI_CNF G - Differential Input / Output Port & Master Clock Configuration SYNC_FREQ[1:0] P 69 - - P 70 Programming Information 59 June 19, 2006 IDT82V3280 WAN PLL Table 42: Register List and Map (Continued) Address (Hex) 0B 13 7E 7F Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reference Page P 71 P 72 P 72 P 73 0C 0D 0E 0F 10 11 12 14 15 16 17 18 19 1A 1B 1C 1D 1E FREQ_MO LOS_FLA MON_SW_PBO_CNFG - Frequency PBO_FRE ULTR_FAS FREQ_MO PBO_EN N_HARD_ EXT_SW G_TO_TD Monitor, Input Clock Selection & PBO Z T_SW N_CLK EN O Control MS_SL_C MS_SL_CTRL_CNFG - Master Slave TRL Control PROTECTION_CNFG - Register ProPROTECTION_DATA[7:0] tection Mode Configuration MPU_SEL_CNFG - Microprocessor MPU_SEL_CNFG[2:0] Interface Mode Configuration Interrupt Registers INTERRUPT_CNFG - Interrupt ConfigHZ_EN INT_POL uration INTERRUPTS1_STS - Interrupt Status IN[8:1] 1 T0_OPER T0_MAIN_ INTERRUPTS2_STS - Interrupt Status IN[14:9] ATING_MO REF_FAIL 2 ED DE AMI1_VIO INPUT_TO AMI2_VIO INTERRUPTS3_STS - Interrupt Status EX_SYNC AMI1_LOS AMI2_LOS T4_STS L _T4 L 3 _ALARM INTERRUPTS1_ENABLE_CNFG IN[8:1] Interrupt Control 1 T0_OPER T0_MAIN_ INTERRUPTS2_ENABLE_CNFG ATING_MO REF_FAIL IN[14:9] Interrupt Control 2 DE ED INTERRUPTS3_ENABLE_CNFG - EX_SYNC INPUT_TO AMI2_VIO AMI1_VIO T4_STS AMI2_LOS AMI1_LOS Interrupt Control 3 _ALARM _T4 L L Input Clock Frequency & Priority Configuration Registers 400HZ_SE IN1_CNFG - Input Clock 1 ConfiguraBUCKET_SEL[1:0] IN_FREQ[3:0] L tion 400HZ_SE IN2_CNFG - Input Clock 2 ConfiguraBUCKET_SEL[1:0] IN_FREQ[3:0] L tion IN3_CNFG - Input Clock 3 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN4_CNFG - Input Clock 4 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN5_IN6_HF_DIV_CNFG - Input Clock 5 & 6 High Frequency Divider ConfiguIN6_DIV[1:0] IN5_DIV[1:0] ration IN5_CNFG - Input Clock 5 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN6_CNFG - Input Clock 6 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN7_CNFG - Input Clock 7 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN8_CNFG - Input Clock 8 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN9_CNFG - Input Clock 9 Configura- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] tion IV IN10_CNFG - Input Clock 10 Configu- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] ration IV P 74 P 74 P 75 P 76 P 77 P 77 P 78 P 79 P 79 P 80 P 81 P 82 P 83 P 84 P 85 P 86 P 87 P 88 Programming Information 60 June 19, 2006 IDT82V3280 WAN PLL Table 42: Register List and Map (Continued) Address (Hex) 1F 20 21 22 23 24 25 26 Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reference Page P 89 P 90 P 91 P 92 P 93 P 93 P 94 P 95 27 28 29 2A 2B 2C 2E 2F 31 32 33 34 IN11_CNFG - Input Clock 11 Configu- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] ration IV IN12_CNFG - Input Clock 12 Configu- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] ration IV IN13_CNFG - Input Clock 13 Configu- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] ration IV IN14_CNFG - Input Clock 14 Configu- DIRECT_D LOCK_8K BUCKET_SEL[1:0] IN_FREQ[3:0] ration IV PRE_DIV_CH_CNFG - DivN Divider PRE_DIV_CH_VALUE[3:0] Channel Selection PRE_DIVN[7:0]_CNFG - DivN Divider PRE_DIVN_VALUE[7:0] Division Factor Configuration 1 PRE_DIVN[14:8]_CNFG DivN PRE_DIVN_VALUE[14:8] Divider Division Factor Configuration 2 IN1_IN2_SEL_PRIORITY_CNFG Input Clock 1 & 2 Priority Configuration IN2_SEL_PRIORITY[3:0] IN1_SEL_PRIORITY[3:0] * IN3_IN4_SEL_PRIORITY_CNFG Input Clock 3 & 4 Priority Configuration IN4_SEL_PRIORITY[3:0] IN3_SEL_PRIORITY[3:0] * IN5_IN6_SEL_PRIORITY_CNFG Input Clock 5 & 6 Priority Configuration IN6_SEL_PRIORITY[3:0] IN5_SEL_PRIORITY[3:0] * IN7_IN8_SEL_PRIORITY_CNFG Input Clock 7 & 8 Priority Configuration IN8_SEL_PRIORITY[3:0] IN7_SEL_PRIORITY[3:0] * IN9_IN10_SEL_PRIORITY_CNFG Input Clock 9 & 10 Priority ConfiguraIN10_SEL_PRIORITY[3:0] IN9_SEL_PRIORITY[3:0] tion * IN11_IN12_SEL_PRIORITY_CNFG Input Clock 11 & 12 Priority ConfiguraIN12_SEL_PRIORITY[3:0] IN11_SEL_PRIORITY[3:0] tion * IN13_IN14_SEL_PRIORITY_CNFG Input Clock 13 & 14 Priority ConfiguraIN14_SEL_PRIORITY[3:0] IN13_SEL_PRIORITY[3:0] tion * Input Clock Quality Monitoring Configuration & Status Registers FREQ_MON_FACTOR_CNFG - FacFREQ_MON_FACTOR[3:0] tor of Frequency Monitor Configuration ALL_FREQ_MON_THRESHOLD_CN FG - Frequency Monitor Threshold for ALL_FREQ_HARD_THRESHOLD[3:0] All Input Clocks Configuration UPPER_THRESHOLD_0_CNFG Upper Threshold for Leaky Bucket UPPER_THRESHOLD_0_DATA[7:0] Configuration 0 LOWER_THRESHOLD_0_CNFG Lower Threshold for Leaky Bucket LOWER_THRESHOLD_0_DATA[7:0] Configuration 0 BUCKET_SIZE_0_CNFG - Bucket BUCKET_SIZE_0_DATA[7:0] Size for Leaky Bucket Configuration 0 DECAY_RATE_0_CNFG - Decay Rate DECAY_RATE_0_DATA for Leaky Bucket Configuration 0 [1:0] P 96 P 97 P 98 P 99 P 100 P 101 P 102 P 102 P 103 P 103 P 103 P 104 Programming Information 61 June 19, 2006 IDT82V3280 WAN PLL Table 42: Register List and Map (Continued) Address (Hex) 35 Register Name UPPER_THRESHOLD_1_CNFG Upper Threshold for Leaky Bucket Configuration 1 LOWER_THRESHOLD_1_CNFG Lower Threshold for Leaky Bucket Configuration 1 BUCKET_SIZE_1_CNFG - Bucket Size for Leaky Bucket Configuration 1 DECAY_RATE_1_CNFG - Decay Rate for Leaky Bucket Configuration 1 UPPER_THRESHOLD_2_CNFG Upper Threshold for Leaky Bucket Configuration 2 LOWER_THRESHOLD_2_CNFG Lower Threshold for Leaky Bucket Configuration 2 BUCKET_SIZE_2_CNFG - Bucket Size for Leaky Bucket Configuration 2 DECAY_RATE_2_CNFG - Decay Rate for Leaky Bucket Configuration 2 UPPER_THRESHOLD_3_CNFG Upper Threshold for Leaky Bucket Configuration 3 LOWER_THRESHOLD_3_CNFG Lower Threshold for Leaky Bucket Configuration 3 BUCKET_SIZE_3_CNFG - Bucket Size for Leaky Bucket Configuration 3 DECAY_RATE_3_CNFG - Decay Rate for Leaky Bucket Configuration 3 IN_FREQ_READ_CH_CNFG - Input Clock Frequency Read Channel Selection IN_FREQ_READ_STS - Input Clock Frequency Read Value IN1_IN2_STS - Input Clock 1 & 2 Status IN3_IN4_STS - Input Clock 3 & 4 Status IN5_IN6_STS - Input Clock 5 & 6 Status IN7_IN8_STS - Input Clock 7 & 8 Status IN9_IN10_STS - Input Clock 9 & 10 Status Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reference Page P 104 UPPER_THRESHOLD_1_DATA[7:0] 36 37 38 39 LOWER_THRESHOLD_1_DATA[7:0] BUCKET_SIZE_1_DATA[7:0] DECAY_RATE_1_DATA [1:0] P 104 P 105 P 105 P 105 UPPER_THRESHOLD_2_DATA[7:0] 3A 3B 3C 3D LOWER_THRESHOLD_2_DATA[7:0] BUCKET_SIZE_2_DATA[7:0] DECAY_RATE_2_DATA [1:0] P 106 P 106 P 106 P 107 UPPER_THRESHOLD_3_DATA[7:0] 3E 3F 40 41 42 43 LOWER_THRESHOLD_3_DATA[7:0] BUCKET_SIZE_3_DATA[7:0] IN_FREQ_VALUE[7:0] IN2_FREQ _HARD_A LARM IN4_FREQ _HARD_A LARM IN6_FREQ _HARD_A LARM IN8_FREQ _HARD_A LARM IN10_FRE Q_HARD_ ALARM IN2_NO_A CTIVITY_A LARM IN4_NO_A CTIVITY_A LARM IN6_NO_A CTIVITY_A LARM IN8_NO_A CTIVITY_A LARM IN10_NO_ ACTIVITY_ ALARM IN2_PH_L OCK_ALA RM IN4_PH_L OCK_ALA RM IN6_PH_L OCK_ALA RM IN8_PH_L OCK_ALA RM IN10_PH_ LOCK_AL ARM IN1_FREQ _HARD_A LARM IN3_FREQ _HARD_A LARM IN5_FREQ _HARD_A LARM IN7_FREQ _HARD_A LARM IN9_FREQ _HARD_A LARM IN1_NO_A CTIVITY_A LARM IN3_NO_A CTIVITY_A LARM IN5_NO_A CTIVITY_A LARM IN7_NO_A CTIVITY_A LARM IN9_NO_A CTIVITY_A LARM IN1_PH_L OCK_ALA RM IN3_PH_L OCK_ALA RM IN5_PH_L OCK_ALA RM IN7_PH_L OCK_ALA RM IN9_PH_L OCK_ALA RM DECAY_RATE_3_DATA [1:0] P 107 P 107 P 108 P 108 P 109 P 109 IN_FREQ_READ_CH[3:0] 44 - - P 110 45 - - P 111 46 - - P 112 47 - - P 113 Programming Information 62 June 19, 2006 IDT82V3280 WAN PLL Table 42: Register List and Map (Continued) Address (Hex) 48 Register Name IN11_IN12_STS - Input Clock 11 & 12 Status IN13_IN14_STS - Input Clock 13 & 14 Status Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 IN11_FRE Q_HARD_ ALARM IN13_FRE Q_HARD_ ALARM Bit 1 IN11_NO_ ACTIVITY_ ALARM IN13_NO_ ACTIVITY_ ALARM Bit 0 IN11_PH_L OCK_ALA RM IN13_PHA SE_LOCK _ALARM Reference Page P 114 49 IN12_FRE IN12_NO_ IN12_PH_ Q_HARD_ ACTIVITY_ LOCK_AL ALARM ALARM ARM IN14_FRE IN14_NO_ IN14_PHA Q_HARD_ ACTIVITY_ SE_LOCK ALARM ALARM _ALARM T0 / T4 DPLL Input Clock Selection Registers P 115 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A INPUT_VALID1_STS - Input Clocks IN[8:1] Validity 1 INPUT_VALID2_STS - Input Clocks IN[14:9] Validity 2 REMOTE_INPUT_VALID1_CNFG IN8_VALID IN7_VALID IN6_VALID IN5_VALID IN4_VALID IN3_VALID IN2_VALID IN1_VALID Input Clocks Validity Configuration 1 REMOTE_INPUT_VALID2_CNFG IN14_VALI IN13_VALI IN12_VALI IN11_VALI IN10_VALI IN9_VALID Input Clocks Validity Configuration 2 D D D D D PRIORITY_TABLE1_STS - Priority HIGHEST_PRIORITY_VALIDATED[3:0] CURRENTLY_SELECTED_INPUT[3:0] Status 1 * SECOND_HIGHEST_PRIORITY_VALIDATED[3:0 PRIORITY_TABLE2_STS - Priority THIRD_HIGHEST_PRIORITY_VALIDATED[3:0] ] Status 2 * T0_INPUT_SEL_CNFG - T0 Selected T0_INPUT_SEL[3:0] Input Clock Configuration T4_LOCK_ T0_FOR_T T4_TEST_ T4_INPUT_SEL_CNFG - T4 Selected T4_INPUT_SEL[3:0] T0 4 T0_PH Input Clock Configuration T0 / T4 DPLL State Machine Control Registers T0_DPLL_ T4_DPLL_ EX_SYNC T0_DPLL_ T4_DPLL_ OPERATING_STS - DPLL Operating T0_DPLL_OPERATING_MODE[2:0] SOFT_FRE SOFT_FRE _ALARM_ LOCK LOCK Status Q_ALARM Q_ALRAM MON T0_OPERATING_MODE_CNFG - T0 T0_OPERATING_MODE[2:0] DPLL Operating Mode Configuration T4_OPERATING_MODE_CNFG - T4 T4_OPERATING_MODE[2:0] DPLL Operating Mode Configuration T0 / T4 DPLL & APLL Configuration Registers T0_GSM_OBSAI_16E1 T0_12E1_24T1_E3_T3 T0_DPLL_APLL_PATH_CNFG - T0 T0_APLL_PATH[3:0] _16T1_SEL[1:0] _SEL[1:0] DPLL & APLL Path Configuration T0_DPLL_START_BW_DAMPING_C NFG - T0 DPLL Start Bandwidth & T0_DPLL_START_DAMPING[2:0] T0_DPLL_START_BW[4:0] Damping Factor Configuration T0_DPLL_ACQ_BW_DAMPING_CNF G - T0 DPLL Acquisition Bandwidth & T0_DPLL_ACQ_DAMPING[2:0] T0_DPLL_ACQ_BW[4:0] Damping Factor Configuration T0_DPLL_LOCKED_BW_DAMPING_ CNFG - T0 DPLL Locked Bandwidth & T0_DPLL_LOCKED_DAMPING[2:0] T0_DPLL_LOCKED_BW[4:0] Damping Factor Configuration T0_BW_OVERSHOOT_CNFG - T0 AUTO_BW T0_LIMT DPLL Bandwidth Overshoot Configu_SEL ration MULTI_PH PHASE_LOSS_COARSE_LIMIT_CNF COARSE_ MULTI_PH _8K_4K_2 PH_LOS_COARSE_LIMT[3:0] G - Phase Loss Coarse Detector Limit PH_LOS_L WIDE_EN _APP K_EN Configuration * IMT_EN P 116 P 116 P 116 P 117 P 117 P 118 P 118 P 119 P 120 P 121 P 121 P 122 P 123 P 124 P 125 P 126 P 127 Programming Information 63 June 19, 2006 IDT82V3280 WAN PLL Table 42: Register List and Map (Continued) Address (Hex) 5B 5C 5D Register Name PHASE_LOSS_FINE_LIMIT_CNFG Phase Loss Fine Detector Limit Configuration * T0_HOLDOVER_MODE_CNFG - T0 DPLL Holdover Mode Configuration T0_HOLDOVER_FREQ[7:0]_CNFG T0 DPLL Holdover Frequency Configuration 1 T0_HOLDOVER_FREQ[15:8]_CNFG - T0 DPLL Holdover Frequency Configuration 2 T0_HOLDOVER_FREQ[23:16]_CNFG - T0 DPLL Holdover Frequency Configuration 3 T4_DPLL_APLL_PATH_CNFG - T4 DPLL & APLL Path Configuration T4_DPLL_LOCKED_BW_DAMPING_ CNFG - T4 DPLL Locked Bandwidth & Damping Factor Configuration CURRENT_DPLL_FREQ[7:0]_STS DPLL Current Frequency Status 1 * CURRENT_DPLL_FREQ[15:8]_STS DPLL Current Frequency Status 2 * CURRENT_DPLL_FREQ[23:16]_STS - DPLL Current Frequency Status 3 * DPLL_FREQ_SOFT_LIMIT_CNFG DPLL Soft Limit Configuration DPLL_FREQ_HARD_LIMIT[7:0]_CNF G - DPLL Hard Limit Configuration 1 DPLL_FREQ_HARD_LIMIT[15:8]_CN FG - DPLL Hard Limit Configuration 2 CURRENT_DPLL_PHASE[7:0]_STS DPLL Current Phase Status 1 * CURRENT_DPLL_PHASE[15:8]_STS - DPLL Current Phase Status 2 * T0_T4_APLL_BW_CNFG - T0 / T4 APLL Bandwidth Configuration OUT1_FREQ_CNFG - Output Clock 1 Frequency Configuration OUT2_FREQ_CNFG - Output Clock 2 Frequency Configuration OUT3_FREQ_CNFG - Output Clock 3 Frequency Configuration OUT4_FREQ_CNFG - Output Clock 4 Frequency Configuration OUT5_FREQ_CNFG - Output Clock 5 Frequency Configuration OUT6_FREQ_CNFG - Output Clock 6 Frequency Configuration Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reference Page P 128 P 129 P 129 FINE_PH_ FAST_LOS PH_LOS_FINE_LIMT[2:0] LOS_LIMT _SW _EN READ_AV TEMP_HOLDOVER_M MAN_HOL AUTO_AV FAST_AVG G ODE[1:0] DOVER G T0_HOLDOVER_FREQ[7:0] 5E T0_HOLDOVER_FREQ[15:8] P 130 5F 60 61 62 63 64 65 66 67 68 69 6A T0_HOLDOVER_FREQ[23:16] T4_APLL_PATH[3:0] T4_DPLL_LOCKED_DAMPING[2:0] T4_GSM_GPS_16E1_1 T4_12E1_24T1_E3_T3 6T1_SEL[1:0] _SEL[1:0] T4_DPLL_LOCKED_B W[1:0] P 130 P 131 P 132 P 132 P 132 P 133 P 133 P 133 P 134 P 134 P 134 T4_APLL_BW[1:0] P 135 CURRENT_DPLL_FREQ[7:0] CURRENT_DPLL_FREQ[15:8] CURRENT_DPLL_FREQ[23:16] FREQ_LIM T_PH_LOS DPLL_FREQ_SOFT_LIMT[6:0] DPLL_FREQ_HARD_LIMT[7:0] DPLL_FREQ_HARD_LIMT[15:8] CURRENT_PH_DATA[7:0] CURRENT_PH_DATA[15:8] T0_APLL_BW[1:0] - Output Configuration Registers 6B 6C 6D 6E 6F 70 OUT1_PATH_SEL[3:0] OUT2_PATH_SEL[3:0] OUT3_PATH_SEL[3:0] OUT4_PATH_SEL[3:0] OUT5_PATH_SEL[3:0] OUT6_PATH_SEL[3:0] OUT1_DIVIDER[3:0] OUT2_DIVIDER[3:0] OUT3_DIVIDER[3:0] OUT4_DIVIDER[3:0] OUT5_DIVIDER[3:0] OUT6_DIVIDER[3:0] P 136 P 137 P 138 P 139 P 140 P 141 Programming Information 64 June 19, 2006 IDT82V3280 WAN PLL Table 42: Register List and Map (Continued) Address (Hex) 71 72 Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reference Page P 142 P 143 73 74 78 7A 7B 7C 7D OUT7_FREQ_CNFG - Output Clock 7 OUT7_PATH_SEL[3:0] OUT7_DIVIDER[3:0] Frequency Configuration OUT8_FREQ_CNFG - Output Clock 8 T4_INPUT AMI_OUT_ 400HZ_SE OUT8_PAT OUT9_INV OUT7_INV OUT6_INV OUT8_EN Frequency Configuration & Output _FAIL DUTY L H_SEL Clock 6, 7 & 9 Invert Configuration OUT9_FREQ_CNFG - Output Clock 9 T4_INPUT OUT9_PAT OUT5_INV OUT4_INV OUT3_INV OUT2_INV OUT1_INV OUT9_EN Frequency Configuration & Output _FAIL H_SEL Clock 1 ~ 5 Invert Configuration 2K_8K_PU FR_MFR_SYNC_CNFG - Frame Sync IN_2K_4K_ 8K_EN 2K_EN L_POSITI 8K_INV 8K_PUL 2K_INV 2K_PUL & Multiframe Sync Output Configura8K_INV ON tion PBO & Phase Offset Control Registers PHASE_MON_PBO_CNFG - Phase IN_NOISE PH_MON_ PH_MON_ PH_TR_MON_LIMT[3:0] Transient Monitor & PBO Configura_WINDOW EN PBO_EN tion PHASE_OFFSET[7:0]_CNFG - Phase PH_OFFSET[7:0] Offset Configuration 1 PHASE_OFFSET[9:8]_CNFG - Phase PH_OFFS PH_OFFSET[9:8] Offset Configuration 2 ET_EN Synchronization Configuration Registers SYNC_MONITOR_CNFG - Sync MonSYNC_MON_LIMT[2:0] itor Configuration SYNC_PHASE_CNFG - Sync Phase SYNC_PH1[1:0] Configuration P 144 P 145 P 146 P 146 P 147 P 148 P 148 7.2 7.2.1 REGISTER DESCRIPTION GLOBAL CONTROL REGISTERS ID[7:0] - Device ID 1 Address: 00H Type: Read Default Value: 10001000 7 ID7 Bit 7-0 Name ID[7:0] Refer to the description of the ID[15:8] bits (b7~0, 01H). 6 ID6 5 ID5 4 ID4 3 ID3 Description 2 ID2 1 ID1 0 ID0 Programming Information 65 June 19, 2006 IDT82V3280 WAN PLL ID[15:8] - Device ID 2 Address: 01H Type: Read Default Value: 00010001 7 ID15 Bit 7-0 6 ID14 Name ID[15:8] 5 ID13 4 ID12 3 ID11 Description The value in the ID[15:0] bits are pre-set, representing the identification number for the IDT82V3280. 2 ID10 1 ID9 0 ID8 MPU_PIN_STS - MPU_MODE[2:0] Pins Status Address: 02H Type: Read Default Value: XXXXXXXX 7 Bit 7-3 2-0 Name 6 5 4 3 2 MPU_PIN_STS2 Description 1 MPU_PIN_STS1 0 MPU_PIN_STS0 Reserved. These bits indicate the value of the MPU_MODE[2:0] pins. MPU_PIN_STS[2:0] The default value of these bits is determined by the MPU_MODE[2:0] pins during reset. NOMINAL_FREQ[7:0]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 1 Address: 04H Type: Read / Write Default Value: 00000000 7 NOMINAL_FRE Q_VALUE7 Bit 7-0 6 NOMINAL_FRE Q_VALUE6 Name 5 NOMINAL_FRE Q_VALUE5 4 NOMINAL_FRE Q_VALUE4 3 NOMINAL_FRE Q_VALUE3 2 NOMINAL_FRE Q_VALUE2 1 NOMINAL_FRE Q_VALUE1 0 NOMINAL_FRE Q_VALUE0 Description NOMINAL_FREQ_VALUE[7:0] Refer to the description of the NOMINAL_FREQ_VALUE[23:16] bits (b7~0, 06H). NOMINAL_FREQ[15:8]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 2 Address: 05H Type: Read / Write Default Value: 00000000 7 NOMINAL_FRE Q_VALUE15 Bit 7-0 6 NOMINAL_FRE Q_VALUE14 Name 5 NOMINAL_FRE Q_VALUE13 4 NOMINAL_FRE Q_VALUE12 3 NOMINAL_FRE Q_VALUE11 2 NOMINAL_FRE Q_VALUE10 1 NOMINAL_FRE Q_VALUE9 0 NOMINAL_FRE Q_VALUE8 Description NOMINAL_FREQ_VALUE[15:8] Refer to the description of the NOMINAL_FREQ_VALUE[23:16] bits (b7~0, 06H). Programming Information 66 June 19, 2006 IDT82V3280 WAN PLL NOMINAL_FREQ[23:16]_CNFG - Crystal Oscillator Frequency Offset Calibration Configuration 3 Address: 06H Type: Read / Write Default Value: 00000000 7 NOMINAL_FRE Q_VALUE23 Bit 6 NOMINAL_FRE Q_VALUE22 Name 5 NOMINAL_FRE Q_VALUE21 4 NOMINAL_FRE Q_VALUE20 3 NOMINAL_FRE Q_VALUE19 2 NOMINAL_FRE Q_VALUE18 1 NOMINAL_FRE Q_VALUE17 0 NOMINAL_FRE Q_VALUE16 Description 7-0 The NOMINAL_FREQ_VALUE[23:0] bits represent a 2's complement signed integer. If the value is multiplied by 0.0000884, the calibration value for the master clock in ppm will be gotten. For example, the frequency offset on OSCI is +3 ppm. Though -3 ppm should be compensated, the calibration value is NOMINAL_FREQ_VALUE[23:16] calculated as +3 ppm: 3 / 0.0000884 = 33937 (Dec.) = 8490 (Hex); So `008490' should be written into these bits. The calibration range is within 741 ppm. T4_T0_REG_SEL_CNFG - T0 / T4 Registers Selection Configuration Address: 07H Type: Read / Write Default Value: XXX0XXXX 7 Bit 7-5 4 3-0 Name T4_T0_SEL 6 5 4 T4_T0_SEL 3 Description Reserved. A part of the registers are shared by T0 and T4 paths. These registers are addressed 26H ~ 2CH, 4EH, 4FH, 5AH, 5BH, 62H ~ 64H, 68H and 69H. This bit determines whether the register configuration is available for T0 or T4 path. 0: T0 path (default). 1: T4 path. Reserved. 2 1 0 - Programming Information 67 June 19, 2006 IDT82V3280 WAN PLL PHASE_ALARM_TIME_OUT_CNFG - Phase Lock Alarm Time-Out Configuration Address: 08H Type: Read / Write Default Value: 00110010 7 MULTI_FACTO R1 Bit 6 MULTI_FACTO R0 Name 5 TIME_OUT_VA LUE5 4 TIME_OUT_VA LUE4 3 TIME_OUT_VA LUE3 2 TIME_OUT_VA LUE2 1 TIME_OUT_VA LUE1 0 TIME_OUT_VAL UE0 Description 7-6 5-0 These bits determine a factor which has a relationship with a period in seconds. A phase lock alarm will be raised if the T0 selected input clock is not locked in T0 DPLL within this period. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', the phase lock alarm will be cleared after this period (starting from when the alarm is raised). Refer to the description of the TIME_OUT_VALUE[5:0] bits (b5~0, 08H). MULTI_FACTOR[1:0] 00: 2 (default) 01: 4 10: 8 11: 16 These bits represent an unsigned integer. If the value in these bits is multiplied by the value in the MULTI_FACTOR[1:0] bits (b7~6, 08H), a period in seconds will be gotten. TIME_OUT_VALUE[5:0] A phase lock alarm will be raised if the T0 selected input clock is not locked in T0 DPLL within this period. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', the phase lock alarm will be cleared after this period (starting from when the alarm is raised). Programming Information 68 June 19, 2006 IDT82V3280 WAN PLL INPUT_MODE_CNFG - Input Mode Configuration Address: 09H Type: Read / Write Default Value: 10100XX0 7 AUTO_EXT_SY NC_EN Bit 7 6 EXT_SYNC_EN 5 PH_ALARM_TI MEOUT 4 SYNC_FREQ1 3 SYNC_FREQ0 2 IN_SONET_SD H 1 MASTER_SLAV E 0 REVERTIVE_M ODE Name Description AUTO_EXT_SYNC_EN Refer to the description of the EXT_SYNC_EN bit (b6, 09H). This bit, together with the AUTO_EXT_SYNC_EN bit (b7, 09H), determines whether EX_SYNC1 is enabled to synchronize the frame sync output signals. AUTO_EXT_SYNC_EN don't-care 0 1 EXT_SYNC_EN 0 1 1 Synchronization Disabled (default) Enabled Enabled if the T0 selected input clock is IN11; otherwise, disabled. 6 EXT_SYNC_EN 5 4-3 2 1 0 This bit determines how to clear the phase lock alarm. 0: The phase lock alarm will be cleared when a `1' is written to the corresponding INn_PH_LOCK_ALARM bit (b4/0, PH_ALARM_TIMEOUT 43H~49H). 1: The phase lock alarm will be cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. (default) These bits set the frequency of the frame sync signal input on the EX_SYNC1 pin. 00: 8 kHz (default) SYNC_FREQ[1:0] 01: 8 kHz. 10: 4 kHz. 11: 2 kHz. This bit selects the SDH or SONET network type. 0: SDH. The DPLL required clock is 2.048 MHz when the IN_FREQ[3:0] bits (b3~0, 14H~17H & 19H~22H) are `0001'; the T0/T4 DPLL output from the 16E1/16T1 path is 16E1; and OUT9 outputs a 2.048 MHz signal if enabled. IN_SONET_SDH 1: SONET. The DPLL required clock is 1.544 MHz when the IN_FREQ[3:0] bits (b3~0, 14H~17H & 19H~22H) are `0001'; the T0/T4 DPLL output from the 16E1/16T1 path is 16T1; and OUT9 outputs a 1.544 MHz signal if enabled. The default value of this bit is determined by the SONET/SDH pin during reset. This bit is read only. It indicates the value of the MS/SL pin. MASTER_SLAVE Its default value is determined by the MS/SL pin during reset. This bit selects Revertive or Non-Revertive switch for T0 path. REVERTIVE_MODE 0: Non-Revertive switch. (default) 1: Revertive switch. Programming Information 69 June 19, 2006 IDT82V3280 WAN PLL DIFFERENTIAL_IN_OUT_OSCI_CNFG - Differential Input / Output Port & Master Clock Configuration Address: 0AH Type: Read / Write Default Value: XXXXX001 7 Bit 7-3 2 6 Name Reserved. This bit selects a better active edge of the master clock. OSC_EDGE 0: The rising edge. (default) 1: The falling edge. This bit selects a port technology for OUT7. OUT7_PECL_LVDS 0: LVDS. (default) 1: PECL. This bit selects a port technology for OUT6. OUT6_PECL_LVDS 0: LVDS. 1: PECL. (default) 5 4 3 2 OSC_EDGE Description 1 OUT7_PECL_LVDS 0 OUT6_PECL_LVDS 1 0 Programming Information 70 June 19, 2006 IDT82V3280 WAN PLL MON_SW_PBO_CNFG - Frequency Monitor, Input Clock Selection & PBO Control Address: 0BH Type: Read / Write Default Value: 100X01X1 7 FREQ_MON_C LK Bit 7 6 LOS_FLAG_TO _TDO Name FREQ_MON_CLK 5 ULTR_FAST_SW 4 EXT_SW 3 PBO_FREZ 2 PBO_EN 1 0 FREQ_MON_H ARD_EN Description 6 5 4 3 2 1 0 The bit selects a reference clock for input clock frequency monitoring. 0: The output of T0 DPLL. 1: The master clock. (default) The bit determines whether the interrupt of T0 selected input clock fail - is reported by the TDO pin. 0: Not reported. TDO pin is used as JTAG test data output which complies with IEEE 1149.1. (default) LOS_FLAG_TO_TDO 1: Reported. TDO pin mimics the state of the T0_MAIN_REF_FAILED bit (b6, 0EH) and does not strictly comply with IEEE 1149.1. This bit determines whether the T0 selected input clock is valid when missing 2 consecutive clock cycles or more. ULTR_FAST_SW 0: Valid. (default) 1: Invalid. This bit determines the T0 input clock selection. 0: Forced selection or Automatic selection, as controlled by the T0_INPUT_SEL[3:0] bits (b3~0, 50H). EXT_SW 1: External Fast selection. The default value of this bit is determined by the FF_SRCSW pin during reset. This bit is valid only when the PBO is enabled by the PBO_EN bit (b2, 0BH). It determines whether PBO is frozen at the current phase offset when a PBO event is triggered. PBO_FREZ 0: Not frozen. (default) 1: Frozen. Further PBO events are ignored and the current phase offset is maintained. This bit determines whether PBO is enabled when the T0 selected input clock switch or the T0 DPLL exiting from Holdover mode or Free-Run mode occurs. PBO_EN 0: Disabled. 1: Enabled. (default) Reserved. This bit determines whether the frequency hard alarm is enabled when the frequency of the input clock with respect to the reference clock is above the frequency hard alarm threshold. The reference clock can be the output of T0 DPLL or the masFREQ_MON_HARD_EN ter clock, as determined by the FREQ_MON_CLK bit (b7, 0BH). 0: Disabled. 1: Enabled. (default) Programming Information 71 June 19, 2006 IDT82V3280 WAN PLL MS_SL_CTRL_CNFG - Master Slave Control Address: 13H Type: Read / Write Default Value: XXXXXXX0 7 Bit 7-1 Name Reserved. These bits, together with the MS/SL pin, control whether the device is configured as the Master or as the Slave. Master/Slave Control MS/SL pin 0 MS_SL_CTRL High Low The default value of this bit is `0'. MS_SL_CTRL Bit 0 1 0 1 Result Master Slave Slave Master 6 5 4 3 Description 2 1 0 MS_SL_CTRL PROTECTION_CNFG - Register Protection Mode Configuration Address: 7EH Type: Read / Write Default Value: 10000101 7 PROTECTION_ DATA7 Bit 6 PROTECTION_ DATA6 Name 5 PROTECTION_ DATA5 4 PROTECTION_ DATA4 3 PROTECTION_ DATA3 2 PROTECTION_ DATA2 1 PROTECTION_ DATA1 0 PROTECTION_ DATA0 Description 7-0 These bits select a register write protection mode. 00000000 - 10000100, 10000111 - 11111111: Protected mode. No other registers can be written except this register. PROTECTION_DATA[7:0] 10000101: Fully Unprotected mode. All the writable registers can be written. (default) 10000110: Single Unprotected mode. One more register can be written besides this register. After write operation (not including writing a `1' to clear the bit to `0'), the device automatically switches to Protected mode. Programming Information 72 June 19, 2006 IDT82V3280 WAN PLL MPU_SEL_CNFG - Microprocessor Interface Mode Configuration Address: 7FH Type: Read / Write Default Value: XXXXXXXX 7 Bit 7-3 6 Name 5 4 3 2 MPU_SEL_CNFG2 Description 1 MPU_SEL_CNFG1 0 MPU_SEL_CNFG0 2-0 Reserved. These bits select a microprocessor interface mode: 000: Reserved. 001: ERPOM mode. 010: Multiplexed mode. MPU_SEL_CNFG[2:0] 011: Intel mode. 100: Motorola mode. 101: Serial mode. 110, 111: Reserved. The default value of these bits are determined by the MPU_MODE[2:0] pins during reset. Programming Information 73 June 19, 2006 IDT82V3280 WAN PLL 7.2.2 INTERRUPT REGISTERS INTERRUPT_CNFG - Interrupt Configuration Address: 0CH Type: Read / Write Default Value: XXXXXX10 7 Bit 7-2 1 Name HZ_EN 6 5 4 3 Description Reserved. This bit determines the output characteristics of the INT_REQ pin. 0: The output on the INT_REQ pin is high/low when the interrupt is active; the output is the opposite when the interrupt is inactive. 1: The output on the INT_REQ pin is high/low when the interrupt is active; the output is in high impedance state when the interrupt is inactive. (default) This bit determines the active level on the INT_REQ pin for an active interrupt indication. 0: Active low. (default) 1: Active high. 2 1 HZ_EN 0 INT_POL 0 INT_POL INTERRUPTS1_STS - Interrupt Status 1 Address: 0DH Type: Read / Write Default Value: 11111111 7 IN8 Bit Name 6 IN7 5 IN6 4 IN5 3 IN4 Description This bit indicates the validity changes (from `valid' to `invalid' or from `invalid' to `valid') for the corresponding INn; i.e., whether there is a transition (from `0' to `1' or from `1' to `0') on the corresponding INn bit (b7~0, 4AH). Here n is any one of 8 to 1. 0: Has not changed. 1: Has changed. (default) This bit is cleared by writing a `1'. 2 IN3 1 IN2 0 IN1 7-0 INn Programming Information 74 June 19, 2006 IDT82V3280 WAN PLL INTERRUPTS2_STS - Interrupt Status 2 Address: 0EH Type: Read / Write Default Value: 00111111 7 T0_OPERATING _MODE Bit 6 T0_MAIN_REF_F AILED Name 5 IN14 4 IN13 3 IN12 Description 2 IN11 1 IN10 0 IN9 7 6 5-0 This bit indicates the operating mode switch for T0 DPLL; i.e., whether the value in the T0_DPLL_OPERATING_MODE[2:0] bits (b2~0, 52H) changes. T0_OPERATING_MODE 0: Has not switched. (default) 1: Has switched. This bit is cleared by writing a `1'. This bit indicates whether the T0 selected input clock has failed. The T0 selected input clock fails when its validity changes from `valid' to `invalid'; i.e., when there is a transition from `1' to `0' on the corresponding INn bit (4AH, 4BH). T0_MAIN_REF_FAILED 0: Has not failed. (default) 1: Has failed. This bit is cleared by writing a `1'. This bit indicates the validity changes (from `valid' to `invalid' or from `invalid' to `valid') for the corresponding INn for T0 path, i.e., whether there is a transition (from `0' to `1' or from `1' to `0') on the corresponding INn bit (b5~0, 4BH). Here n is any one of 14 to 9. INn 0: Has not changed. 1: Has changed. (default) This bit is cleared by writing a `1'. Programming Information 75 June 19, 2006 IDT82V3280 WAN PLL INTERRUPTS3_STS - Interrupt Status 3 Address: 0FH Type: Read / Write Default Value: 11X10000 7 EX_SYNC_ALARM Bit 6 T4_STS Name 5 4 INPUT_TO_T4 3 AMI2_VIOL Description 2 AMI2_LOS 1 AMI1_VIOL 0 AMI1_LOS 7 6 5 4 3 2 1 0 This bit indicates whether an external sync alarm is raised; i.e., whether there is a transition from `0' to `1' on the EX_SYNC_ALARM_MON bit (b7, 52H). EX_SYNC_ALARM 0: Has not occurred. 1: Has occurred. (default) This bit is cleared by writing a `1'. This bit indicates the T4 DPLL locking status changes (from `locked' to `unlocked' or from `unlocked' to `locked'); i.e., whether there is a transition (from `0' to `1' or from `1' to `0') on the T4_DPLL_LOCK bit (b6, 52H). T4_STS 0: Has not changed. 1: Has changed. (default) This bit is cleared by writing a `1'. Reserved. This bit indicates whether all the input clocks for T4 path changes to be unqualified; i.e., whether the HIGHEST_PRIORITY_VALIDATED[3:0] bits (b7~4, 4EH) are set to `0000' when these bits are available for T4 path. INPUT_TO_T4 0: Has not changed. 1: Has changed. (default) This bit is cleared by writing a `1'. This bit indicates whether IN2 has an AMI violation. 0: Has no AMI violation. (default) AMI2_VIOL 1: Has an AMI violation. This bit is cleared by writing a `1'. This bit indicates whether IN2 has a LOS error. 0: Has no LOS error. (default) AMI2_LOS 1: Has a LOS error. This bit is cleared by writing a `1'. This bit indicates whether IN1 has an AMI violation. 0: Has no AMI violation. (default) AMI1_VIOL 1: Has an AMI violation. This bit is cleared by writing a `1'. This bit indicates whether IN1 has a LOS error. 0: Has no LOS error. (default) AMI1_LOS 1: Has a LOS error. This bit is cleared by writing a `1'. Programming Information 76 June 19, 2006 IDT82V3280 WAN PLL INTERRUPTS1_ENABLE_CNFG - Interrupt Control 1 Address: 10H Type: Read / Write Default Value: 00000000 7 IN8 Bit 7-0 Name INn 6 IN7 5 IN6 4 IN5 3 IN4 Description This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the input clock validity changes (from `valid' to `invalid' or from `invalid' to `valid'), i.e., when the corresponding INn bit (b7~0, 0DH) is `1'. Here n is any one of 8 to 1. 0: Disabled. (default) 1: Enabled. 2 IN3 1 IN2 0 IN1 INTERRUPTS2_ENABLE_CNFG - Interrupt Control 2 Address: 11H Type: Read / Write Default Value: 00000000 7 T0_OPERATING _MODE Bit 7 6 T0_MAIN_REF_F AILED Name 5 IN14 4 IN13 3 IN12 Description 2 IN11 1 IN10 0 IN9 6 5-0 This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the T0 DPLL operating mode switches, i.e., when the T0_OPERATING_MODE bit (b7, 0EH) is `1'. T0_OPERATING_MODE 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the T0 selected input clock has failed; i.e., when the T0_MAIN_REF_FAILED bit (b6, 0EH) is `1'. T0_MAIN_REF_FAILED 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the input clock validity changes (from `valid' to `invalid' or from `invalid' to `valid'), i.e., when the corresponding INn bit (b5~0, 0EH) is `1'. Here n INn is any one of 14 to 9. 0: Disabled. (default) 1: Enabled. Programming Information 77 June 19, 2006 IDT82V3280 WAN PLL INTERRUPTS3_ENABLE_CNFG - Interrupt Control 3 Address: 12H Type: Read / Write Default Value: 00X00000 7 EX_SYNC_ALARM Bit 7 6 T4_STS Name 5 4 INPUT_TO_T4 3 AMI2_VIOL Description 2 AMI2_LOS 1 AMI1_VIOL 0 AMI1_LOS 6 5 4 3 2 1 0 This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when an external sync alarm has occurred, i.e., when the EX_SYNC_ALARM bit (b7, 0FH) is `1'. EX_SYNC_ALARM 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when the T4 DPLL locking status changes (from `locked' to `unlocked' or from `unlocked' to `locked'), i.e., when the T4_STS bit (b6, 0FH) is `1'. T4_STS 0: Disabled. (default) 1: Enabled. Reserved. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when all the input clocks for T4 path change to be unqualified, i.e., when the INPUT_TO_T4 bit (b4, 0FH) is `1'. INPUT_TO_T4 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when IN2 has AMI violation, i.e., when the AMI2_VIOL bit (b3, 0FH) is `1'. AMI2_VIOL 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when IN2 has LOS error, i.e., when the AMI2_LOS bit (b2, 0FH) is `1'. AMI2_LOS 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when IN1 has AMI violation, i.e., when the AMI1_VIOL bit (b1, 0FH) is `1'. AMI1_VIOL 0: Disabled. (default) 1: Enabled. This bit controls whether the interrupt is enabled to be reported on the INT_REQ pin when IN1 has LOS error, i.e., when the AMI1_LOS bit (b0, 0FH) is `1'. AMI1_LOS 0: Disabled. (default) 1: Enabled. Programming Information 78 June 19, 2006 IDT82V3280 WAN PLL 7.2.3 INPUT CLOCK FREQUENCY & PRIORITY CONFIGURATION REGISTERS IN1_CNFG - Input Clock 1 Configuration Address: 14H Type: Read / Write Default Value: X0000000 7 Bit 7 6 6 400HZ_SEL Name 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 Description 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 5-4 3-0 Reserved. This bit should be set to match the clock input on IN1: 400HZ_SEL 0: 64 kHz + 8 kHz. (default) 1: 64 kHz + 8 kHz + 0.4 kHz. These bits select one of the four groups of leaky bucket configuration registers for IN1: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN1: IN_FREQ[3:0] 0000: 8 kHz. (default) 0001 ~ 1111: Reserved. IN2_CNFG - Input Clock 2 Configuration Address: 15H Type: Read / Write Default Value: X0000000 7 Bit 7 6 6 400HZ_SEL Name 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description 5-4 3-0 Reserved. This bit should be set to match the clock input on IN2: 400HZ_SEL 0: 64 kHz + 8 kHz. (default) 1: 64 kHz + 8 kHz + 0.4 kHz. These bits select one of the four groups of leaky bucket configuration registers for IN2: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN2: IN_FREQ[3:0] 0000: 8 kHz. (default) 0001 ~ 1111: Reserved. Programming Information 79 June 19, 2006 IDT82V3280 WAN PLL IN3_CNFG - Input Clock 3 Configuration Address: 16H Type: Read / Write Default Value: 00000000 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 16H). This bit, together with the DIRECT_DIV bit (b7, 16H), determines whether the DivN Divider or the Lock 8k Divider is used for IN3: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN3: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN3: 0000: 8 kHz. (default) 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN3, the required frequency should not be set higher than that of the input clock. Programming Information 80 June 19, 2006 IDT82V3280 WAN PLL IN4_CNFG - Input Clock 4 Configuration Address: 17H Type: Read / Write Default Value: 00000000 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 17H). This bit, together with the DIRECT_DIV bit (b7, 17H), determines whether the DivN Divider or the Lock 8k Divider is used for IN4: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN4: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN4: 0000: 8 kHz. (default) 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For the IN4, the required frequency should not be set higher than that of the input clock. Programming Information 81 June 19, 2006 IDT82V3280 WAN PLL IN5_IN6_HF_DIV_CNFG - Input Clock 5 & 6 High Frequency Divider Configuration Address: 18H Type: Read / Write Default Value: 00XXXX00 7 IN6_DIV1 Bit 6 IN6_DIV0 Name 5 4 3 Description These bits determine whether the HF Divider is used and what the division factor is for IN6 frequency division: 00: Bypassed. (default) 01: Divided by 4. 10: Divided by 5. 11: Reserved. Reserved. These bits determine whether the HF Divider is used and what the division factor is for IN5 frequency division: 00: Bypassed. (default) 01: Divided by 4. 10: Divided by 5. 11: Reserved. 2 1 IN5_DIV1 0 IN5_DIV0 7-6 IN6_DIV[1:0] 5-2 - 1-0 IN5_DIV[1:0] Programming Information 82 June 19, 2006 IDT82V3280 WAN PLL IN5_CNFG - Input Clock 5 Configuration Address: 19H Type: Read / Write Default Value: 00000011 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 19H). This bit, together with the DIRECT_DIV bit (b7, 19H), determines whether the DivN Divider or the Lock 8k Divider is used for IN5: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN5: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN5: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. (default) 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. The required frequency should not be set higher than that of the input clock. Programming Information 83 June 19, 2006 IDT82V3280 WAN PLL IN6_CNFG - Input Clock 6 Configuration Address: 1AH Type: Read / Write Default Value: 00000011 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 1AH). This bit, together with the DIRECT_DIV bit (b7, 1AH), determines whether the DivN Divider or the Lock 8k Divider is used for IN6: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN6: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN6: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. (default) 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN6, the required frequency should not be set higher than that of the input clock. Programming Information 84 June 19, 2006 IDT82V3280 WAN PLL IN7_CNFG - Input Clock 7 Configuration Address: 1BH Type: Read / Write Default Value: 00000011 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 1BH). This bit, together with the DIRECT_DIV bit (b7, 1BH), determines whether the DivN Divider or the Lock 8k Divider is used for IN7: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN7: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN7: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. (default) 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN7, the required frequency should not be set higher than that of the input clock. Programming Information 85 June 19, 2006 IDT82V3280 WAN PLL IN8_CNFG - Input Clock 8 Configuration Address: 1CH Type: Read / Write Default Value: 00000011 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 1CH). This bit, together with the DIRECT_DIV bit (b7, 1CH), determines whether the DivN Divider or the Lock 8k Divider is used for IN8: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 0 0 1 1 6 LOCK_8K 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN8: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN8: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. (default) 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN8, the required frequency should not be set higher than that of the input clock. Programming Information 86 June 19, 2006 IDT82V3280 WAN PLL IN9_CNFG - Input Clock 9 Configuration Address: 1DH Type: Read / Write Default Value: 00000011 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 1DH). This bit, together with the DIRECT_DIV bit (b7, 1DH), determines whether the DivN Divider or the Lock 8k Divider is used for IN9: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN9: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN9: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. (default) 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN9, the required frequency should not be set higher than that of the input clock. Programming Information 87 June 19, 2006 IDT82V3280 WAN PLL IN10_CNFG - Input Clock 10 Configuration Address: 1EH Type: Read / Write Default Value: 00000011 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 1EH). This bit, together with the DIRECT_DIV bit (b7, 1EH), determines whether the DivN Divider or the Lock 8k Divider is used for IN10: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN10: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN10: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. (default) 0100: 25.92 MHz. IN_FREQ[3:0] 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN10, the required frequency should not be set higher than that of the input clock. Programming Information 88 June 19, 2006 IDT82V3280 WAN PLL IN11_CNFG - Input Clock 11 Configuration Address: 1FH Type: Read / Write Default Value: 0000XXXX 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 1FH). This bit, together with the DIRECT_DIV bit (b7, 1FH), determines whether the DivN Divider or the Lock 8k Divider is used for IN11: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN11: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN11: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). 0010: 6.48 MHz. 0011: 19.44 MHz. 0100: 25.92 MHz. 0101: 38.88 MHz. IN_FREQ[3:0] 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN11, the required frequency should not be set higher than that of the input clock. The default value of these bits depends on the device application as follows: In Master / Slave application, when the device is configured as the Master, the default value is `0001'; when the device is configured as the Slave, the default value is `0010'. Programming Information 89 June 19, 2006 IDT82V3280 WAN PLL IN12_CNFG - Input Clock 12 Configuration Address: 20H Type: Read / Write Default Value: 00000001 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 20H). This bit, together with the DIRECT_DIV bit (b7, 20H), determines whether the DivN Divider or the Lock 8k Divider is used for IN12: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN12: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN12: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). (default) 0010: 6.48 MHz. 0011: 19.44 MHz. IN_FREQ[3:0] 0100: 25.92 MHz. 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN12, the required frequency should not be set higher than that of the input clock. Programming Information 90 June 19, 2006 IDT82V3280 WAN PLL IN13_CNFG - Input Clock 13 Configuration Address: 21H Type: Read / Write Default Value: 00000001 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 21H). This bit, together with the DIRECT_DIV bit (b7, 21H), determines whether the DivN Divider or the Lock 8k Divider is used for IN13: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN13: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN13: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). (default) 0010: 6.48 MHz. 0011: 19.44 MHz. IN_FREQ[3:0] 0100: 25.92 MHz. 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN13, the required frequency should not be set higher than that of the input clock. Programming Information 91 June 19, 2006 IDT82V3280 WAN PLL IN14_CNFG - Input Clock 14 Configuration Address: 22H Type: Read / Write Default Value: 00000001 7 DIRECT_DIV Bit 7 6 LOCK_8K Name DIRECT_DIV 5 BUCKET_SEL1 4 BUCKET_SEL0 3 IN_FREQ3 2 IN_FREQ2 1 IN_FREQ1 0 IN_FREQ0 Description Refer to the description of the LOCK_8K bit (b6, 22H). This bit, together with the DIRECT_DIV bit (b7, 22H), determines whether the DivN Divider or the Lock 8k Divider is used for IN14: DIRECT_DIV bit LOCK_8K bit 0 1 0 1 Used Divider Both bypassed (default) Lock 8k Divider DivN Divider Reserved 6 LOCK_8K 0 0 1 1 5-4 3-0 These bits select one of the four groups of leaky bucket configuration registers for IN14: 00: Group 0; the addresses of the configuration registers are 31H ~ 34H. (default) BUCKET_SEL[1:0] 01: Group 1; the addresses of the configuration registers are 35H ~ 38H. 10: Group 2; the addresses of the configuration registers are 39H ~ 3CH. 11: Group 3; the addresses of the configuration registers are 3DH ~ 40H. These bits set the DPLL required frequency for IN14: 0000: 8 kHz. 0001: 1.544 MHz (when the IN_SONET_SDH bit (b2, 09H) is `1') / 2.048 MHz (when the IN_SONET_SDH bit (b2, 09H) is `0'). (default) 0010: 6.48 MHz. 0011: 19.44 MHz. IN_FREQ[3:0] 0100: 25.92 MHz. 0101: 38.88 MHz. 0110 ~ 1000: Reserved. 1001: 2 kHz. 1010: 4 kHz. 1011 ~ 1111: Reserved. For IN14, the required frequency should not be set higher than that of the input clock. Programming Information 92 June 19, 2006 IDT82V3280 WAN PLL PRE_DIV_CH_CNFG - DivN Divider Channel Selection Address: 23H Type: Read / Write Default Value: XXXX0000 7 Bit 7-4 6 5 Name 4 3 PRE_DIV_CH_VALUE3 2 PRE_DIV_CH_VALUE2 1 PRE_DIV_CH_VALUE1 0 PRE_DIV_CH_VALUE0 Description 3-0 Reserved. This register is an indirect address register for Register 24H and 25H. These bits select an input clock. The value set in the PRE_DIVN_VALUE[14:0] bits (25H, 24H) is available for the selected input clock. 0000: Reserved. (default) 0001, 0010: Reserved. PRE_DIV_CH_VALUE[3:0] 0011: IN3. 0100: IN4. ...... 1101: IN13. 1110: IN14. 1111: Reserved. PRE_DIVN[7:0]_CNFG - DivN Divider Division Factor Configuration 1 Address: 24H Type: Read / Write Default Value: 00000000 7 PRE_DIVN_VA LUE7 Bit 7-0 6 PRE_DIVN_VA LUE6 Name 5 PRE_DIVN_VA LUE5 4 PRE_DIVN_VA LUE4 3 PRE_DIVN_VA LUE3 2 PRE_DIVN_VA LUE2 1 PRE_DIVN_VA LUE1 0 PRE_DIVN_VA LUE0 Description PRE_DIVN_VALUE[7:0] Refer to the description of the PRE_DIVN_VALUE[14:8] bits (b6~0, 25H). Programming Information 93 June 19, 2006 IDT82V3280 WAN PLL PRE_DIVN[14:8]_CNFG - DivN Divider Division Factor Configuration 2 Address: 25H Type: Read / Write Default Value: X0000000 7 Bit 7 6 PRE_DIVN_VAL UE14 Name 5 PRE_DIVN_VAL UE13 4 PRE_DIVN_VAL UE12 3 PRE_DIVN_VAL UE11 2 PRE_DIVN_VAL UE10 1 PRE_DIVN_VAL UE9 0 PRE_DIVN_VAL UE8 Description Reserved. If the value in the PRE_DIVN_VALUE[14:0] bits is plus 1, the division factor for an input clock will be gotten. The input clock is selected by the PRE_DIV_CH_VALUE[3:0] bits (b3~0, 23H). A value from `0' to `4BEF' (Hex) can be written into, corresponding to a division factor from 1 to 19440. The others are reserved. So the DivN Divider only supports an input clock whose frequency is lower than (<) 155.52 MHz. The division factor setting should observe the following order: 1. Write the lower eight bits of the division factor to the PRE_DIVN_VALUE[7:0] bits; 2. Write the higher eight bits of the division factor to the PRE_DIVN_VALUE[14:8] bits. 6-0 PRE_DIVN_VALUE[14:8] Programming Information 94 June 19, 2006 IDT82V3280 WAN PLL IN1_IN2_SEL_PRIORITY_CNFG - Input Clock 1 & 2 Priority Configuration * Address: 26H Type: Read / Write Default Value: T0 - 00110010 / T4 - 00000000 7 IN2_SEL_PRIO RITY3 Bit 6 IN2_SEL_PRIO RITY2 Name 5 IN2_SEL_PRIO RITY1 4 IN2_SEL_PRIO RITY0 3 IN1_SEL_PRIO RITY3 2 IN1_SEL_PRIO RITY2 1 IN1_SEL_PRIO RITY1 0 IN1_SEL_PRIO RITY0 Description 7-4 3-0 These bits set the priority of the corresponding INn. Here n is 2: 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. (T0 default) 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. INn_SEL_PRIORITY[3:0] 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. These bits set the priority of the corresponding INn. Here n is 1: 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. (T0 default) 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. INn_SEL_PRIORITY[3:0] 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. Programming Information 95 June 19, 2006 IDT82V3280 WAN PLL IN3_IN4_SEL_PRIORITY_CNFG - Input Clock 3 & 4 Priority Configuration * Address: 27H Type: Read / Write Default Value: T0 - 01010100 / T4 - 00000000 7 IN4_SEL_PRIO RITY3 Bit 6 IN4_SEL_PRIO RITY2 Name 5 IN4_SEL_PRIO RITY1 4 IN4_SEL_PRIO RITY0 3 IN3_SEL_PRIO RITY3 2 IN3_SEL_PRIO RITY2 Description These bits set the priority of the corresponding INn. Here n is 4. 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. (T0 default) 0110: Priority 6. 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. These bits set the priority of the corresponding INn. Here n is 3. 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. (T0 default) 0101: Priority 5. 0110: Priority 6. 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. 1 IN3_SEL_PRIO RITY1 0 IN3_SEL_PRIO RITY0 7-4 INn_SEL_PRIORITY[3:0] 3-0 INn_SEL_PRIORITY[3:0] Programming Information 96 June 19, 2006 IDT82V3280 WAN PLL IN5_IN6_SEL_PRIORITY_CNFG - Input Clock 5 & 6 Priority Configuration * Address: 28H Type: Read / Write Default Value: T0/T4 - 01110110 7 IN6_SEL_PRIO RITY3 Bit 6 IN6_SEL_PRIO RITY2 Name 5 IN6_SEL_PRIO RITY1 4 IN6_SEL_PRIO RITY0 3 IN5_SEL_PRIO RITY3 2 IN5_SEL_PRIO RITY2 Description These bits set the priority of the corresponding INn. Here n is 6. 0000: Disable INn for automatic selection. 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. 0111: Priority 7. (default) 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. These bits set the priority of the corresponding INn. Here n is 5. 0000: Disable INn for automatic selection. 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. (default) 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. 1 IN5_SEL_PRIO RITY1 0 IN5_SEL_PRIO RITY0 7-4 INn_SEL_PRIORITY[3:0] 3-0 INn_SEL_PRIORITY[3:0] Programming Information 97 June 19, 2006 IDT82V3280 WAN PLL IN7_IN8_SEL_PRIORITY_CNFG - Input Clock 7 & 8 Priority Configuration * Address: 29H Type: Read / Write Default Value: 10011000 7 IN8_SEL_PRIO RITY3 Bit 6 IN8_SEL_PRIO RITY2 Name 5 IN8_SEL_PRIO RITY1 4 IN8_SEL_PRIO RITY0 3 IN7_SEL_PRIO RITY3 2 IN7_SEL_PRIO RITY2 1 IN7_SEL_PRIO RITY1 0 IN7_SEL_PRIO RITY0 Description 7-4 3-0 These bits set the priority of the corresponding INn. Here n is 8. 0000: Disable INn for automatic selection. 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. INn_SEL_PRIORITY[3:0] 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. (default) 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. These bits set the priority of the corresponding INn. Here n is 7. 0000: Disable INn for automatic selection. 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. INn_SEL_PRIORITY[3:0] 0111: Priority 7. 1000: Priority 8. (default) 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. Programming Information 98 June 19, 2006 IDT82V3280 WAN PLL IN9_IN10_SEL_PRIORITY_CNFG - Input Clock 9 & 10 Priority Configuration * Address: 2AH Type: Read / Write Default Value: 10111010 7 IN10_SEL_PRI ORITY3 Bit 6 IN10_SEL_PRI ORITY2 Name 5 IN10_SEL_PRI ORITY1 4 IN10_SEL_PRI ORITY0 3 IN9_SEL_PRIO RITY3 2 IN9_SEL_PRIO RITY2 Description These bits set the priority of the corresponding INn. Here n is 10. 0000: Disable INn for automatic selection. 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. (default) 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. These bits set the priority of the corresponding INn. Here n is 9. 0000: Disable INn for automatic selection. 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. (default) 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. 1 IN9_SEL_PRIO RITY1 0 IN9_SEL_PRIO RITY0 7-4 INn_SEL_PRIORITY[3:0] 3-0 INn_SEL_PRIORITY[3:0] Programming Information 99 June 19, 2006 IDT82V3280 WAN PLL IN11_IN12_SEL_PRIORITY_CNFG - Input Clock 11 & 12 Priority Configuration * Address: 2BH Type: Read / Write Default Value: 11011100 (T0 Master)/11010001 (T0 Slave) 00000000 (T4) 7 IN12_SEL_PRI ORITY3 Bit 6 IN12_SEL_PRI ORITY2 Name 5 IN12_SEL_PRI ORITY1 4 IN12_SEL_PRI ORITY0 3 IN11_SEL_PRI ORITY3 2 IN11_SEL_PRI ORITY2 Description 1 IN11_SEL_PRI ORITY1 0 IN11_SEL_PRI ORITY0 7-4 3-0 These bits set the priority of the corresponding INn. Here n is 12: 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. INn_SEL_PRIORITY[3:0] 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. (T0 Master/Slave default) 1110: Priority 14. 1111: Priority 15. These bits set the priority of the corresponding INn. Here n is 11: 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. (T0 Slave default) 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. INn_SEL_PRIORITY[3:0] 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. (T0 Master default) 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. Programming Information 100 June 19, 2006 IDT82V3280 WAN PLL IN13_IN14_SEL_PRIORITY_CNFG - Input Clock 13 & 14 Priority Configuration * Address: 2CH Type: Read / Write Default Value: 11111110 (T0) 00000000 (T4) 7 IN14_SEL_PRI ORITY3 Bit 6 IN14_SEL_PRI ORITY2 Name 5 IN14_SEL_PRI ORITY1 4 IN14_SEL_PRI ORITY0 3 IN13_SEL_PRI ORITY3 2 IN13_SEL_PRI ORITY2 Description These bits set the priority of the corresponding INn. Here n is 14: 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. 1111: Priority 15. (T0 default) These bits set the priority of the corresponding INn. Here n is 13: 0000: Disable INn for automatic selection. (T4 default) 0001: Priority 1. 0010: Priority 2. 0011: Priority 3. 0100: Priority 4. 0101: Priority 5. 0110: Priority 6. 0111: Priority 7. 1000: Priority 8. 1001: Priority 9. 1010: Priority 10. 1011: Priority 11. 1100: Priority 12. 1101: Priority 13. 1110: Priority 14. (T0 default) 1111: Priority 15. 1 IN13_SEL_PRI ORITY1 0 IN13_SEL_PRI ORITY0 7-4 INn_SEL_PRIORITY[3:0] 3-0 INn_SEL_PRIORITY[3:0] Programming Information 101 June 19, 2006 IDT82V3280 WAN PLL 7.2.4 INPUT CLOCK QUALITY MONITORING CONFIGURATION & STATUS REGISTERS FREQ_MON_FACTOR_CNFG - Factor of Frequency Monitor Configuration Address: 2EH Type: Read / Write Default Value: XXXX1011 7 Bit 7-4 6 Name 5 4 3 FREQ_MON_F ACTOR3 2 FREQ_MON_F ACTOR2 1 FREQ_MON_F ACTOR1 0 FREQ_MON_F ACTOR0 Description 3-0 Reserved. These bits determine a factor. The factor has a relationship with the frequency hard alarm threshold in ppm (refer to the description of the ALL_FREQ_HARD_THRESHOLD[3:0] bits (b3~0, 2FH)) and with the frequency of the input clock with respect to the master clock in ppm (refer to the description of the IN_FREQ_VALUE[7:0] bits (b7~0, 42H)). The factor represents the accuracy of the frequency monitor and should be set according to the requirements of different applications. 0000: 0.0032. 0001: 0.0064. 0010: 0.0127. 0011: 0.0257. FREQ_MON_FACTOR[3:0] 0100: 0.0514. 0101: 0.103. 0110: 0.206. 0111: 0.412. 1000: 0.823. 1001: 1.646. 1010: 3.292. 1011: 3.81. (default) 1100 - 1111: 4.6. ALL_FREQ_MON_THRESHOLD_CNFG - Frequency Monitor Threshold for All Input Clocks Configuration Address: 2FH Type: Read / Write Default Value: XXXX0011 7 Bit 7-4 6 Name 5 4 3 ALL_FREQ_HARD_ THRESHOLD3 2 ALL_FREQ_HARD_ THRESHOLD2 1 ALL_FREQ_HARD_ THRESHOLD1 0 ALL_FREQ_HARD_ THRESHOLD0 Description 3-0 Reserved. These bits represent an unsigned integer. The frequency hard alarm threshold in ppm can be calculated as follows: ALL_FREQ_HARD_THRESHOLD[3:0] Frequency Hard Alarm Threshold (ppm) = (ALL_FREQ_HARD_THRESHOLD[3:0] + 1) X FREQ_MON_FACTOR[3:0] (b3~0, 2EH) This threshold is symmetrical about zero. Programming Information 102 June 19, 2006 IDT82V3280 WAN PLL UPPER_THRESHOLD_0_CNFG - Upper Threshold for Leaky Bucket Configuration 0 Address: 31H Type: Read / Write Default Value: 00000110 7 UPPER_THRE SHOLD_0_DAT A7 Bit 7-0 6 UPPER_THRE SHOLD_0_DAT A6 Name UPPER_THRESHOLD_0_DATA[7:0] 5 UPPER_THRE SHOLD_0_DAT A5 4 UPPER_THRE SHOLD_0_DAT A4 3 UPPER_THRE SHOLD_0_DAT A3 2 UPPER_THRE SHOLD_0_DAT A2 Description These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumulated events is above this threshold, a no-activity alarm is raised. 1 UPPER_THRE SHOLD_0_DAT A1 0 UPPER_THRE SHOLD_0_DAT A0 LOWER_THRESHOLD_0_CNFG - Lower Threshold for Leaky Bucket Configuration 0 Address: 32H Type: Read / Write Default Value: 00000100 7 LOWER_THRE SHOLD_0_DAT A7 Bit 7-0 6 LOWER_THRE SHOLD_0_DAT A6 Name LOWER_THRESHOLD_0_DATA[7:0] 5 LOWER_THRE SHOLD_0_DAT A5 4 LOWER_THRE SHOLD_0_DAT A4 3 LOWER_THRE SHOLD_0_DAT A3 2 LOWER_THRE SHOLD_0_DAT A2 Description These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated events is below this threshold, the no-activity alarm is cleared. 1 LOWER_THRE SHOLD_0_DAT A1 0 LOWER_THRE SHOLD_0_DAT A0 BUCKET_SIZE_0_CNFG - Bucket Size for Leaky Bucket Configuration 0 Address: 33H Type: Read / Write Default Value: 00001000 7 BUCKET_SIZE _0_DATA7 Bit 7-0 6 BUCKET_SIZE _0_DATA6 Name BUCKET_SIZE_0_DATA[7:0] 5 BUCKET_SIZE _0_DATA5 4 BUCKET_SIZE _0_DATA4 3 BUCKET_SIZE _0_DATA3 2 BUCKET_SIZE _0_DATA2 1 BUCKET_SIZE _0_DATA1 0 BUCKET_SIZE _0_DATA0 Description These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach the bucket size, the accumulator will stop increasing even if further events are detected. Programming Information 103 June 19, 2006 IDT82V3280 WAN PLL DECAY_RATE_0_CNFG - Decay Rate for Leaky Bucket Configuration 0 Address: 34H Type: Read / Write Default Value: XXXXXX01 7 Bit 7-2 6 Name 5 4 3 2 Description 1 DECAY_RATE_ 0_DATA1 0 DECAY_RATE_ 0_DATA0 1-0 Reserved. These bits set a decay rate for the internal leaky bucket accumulator: 00: The accumulator decreases by 1 in every 128 ms with no event detected. DECAY_RATE_0_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default) 10: The accumulator decreases by 1 in every 512 ms with no event detected. 11: The accumulator decreases by 1 in every 1024 ms with no event detected. UPPER_THRESHOLD_1_CNFG - Upper Threshold for Leaky Bucket Configuration 1 Address: 35H Type: Read / Write Default Value: 00000110 7 UPPER_THRE SHOLD_1_DAT A7 Bit 7-0 6 UPPER_THRE SHOLD_1_DAT A6 Name UPPER_THRESHOLD_1_DATA[7:0] 5 UPPER_THRE SHOLD_1_DAT A5 4 UPPER_THRE SHOLD_1_DAT A4 3 UPPER_THRE SHOLD_1_DAT A3 2 UPPER_THRE SHOLD_1_DAT A2 Description These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumulated events is above this threshold, a no-activity alarm is raised. 1 UPPER_THRE SHOLD_1_DAT A1 0 UPPER_THRE SHOLD_1_DAT A0 LOWER_THRESHOLD_1_CNFG - Lower Threshold for Leaky Bucket Configuration 1 Address: 36H Type: Read / Write Default Value: 00000100 7 LOWER_THRE SHOLD_1_DAT A7 Bit 7-0 6 LOWER_THRE SHOLD_1_DAT A6 Name 5 LOWER_THRE SHOLD_1_DAT A5 4 LOWER_THRE SHOLD_1_DAT A4 3 LOWER_THRE SHOLD_1_DAT A3 2 LOWER_THRE SHOLD_1_DAT A2 Description 1 LOWER_THRE SHOLD_1_DAT A1 0 LOWER_THRE SHOLD_1_DAT A0 These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated LOWER_THRESHOLD_1_DATA[7:0] events is below this threshold, the no-activity alarm is cleared. Programming Information 104 June 19, 2006 IDT82V3280 WAN PLL BUCKET_SIZE_1_CNFG - Bucket Size for Leaky Bucket Configuration 1 Address: 37H Type: Read / Write Default Value: 00001000 7 BUCKET_SIZE _1_DATA7 Bit 7-0 6 BUCKET_SIZE _1_DATA6 Name BUCKET_SIZE_1_DATA[7:0] 5 BUCKET_SIZE _1_DATA5 4 BUCKET_SIZE _1_DATA4 3 BUCKET_SIZE _1_DATA3 2 BUCKET_SIZE _1_DATA2 Description These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach the bucket size, the accumulator will stop increasing even if further events are detected. 1 BUCKET_SIZE _1_DATA1 0 BUCKET_SIZE _1_DATA0 DECAY_RATE_1_CNFG - Decay Rate for Leaky Bucket Configuration 1 Address: 38H Type: Read / Write Default Value: XXXXXX01 7 Bit 7-2 6 Name 5 4 3 2 Description 1 DECAY_RATE_ 1_DATA1 0 DECAY_RATE_ 1_DATA0 1-0 Reserved. These bits set a decay rate for the internal leaky bucket accumulator: 00: The accumulator decreases by 1 in every 128 ms with no event detected. DECAY_RATE_1_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default) 10: The accumulator decreases by 1 in every 512 ms with no event detected. 11: The accumulator decreases by 1 in every 1024 ms with no event detected. UPPER_THRESHOLD_2_CNFG - Upper Threshold for Leaky Bucket Configuration 2 Address: 39H Type: Read / Write Default Value: 00000110 7 UPPER_THRE SHOLD_2_DAT A7 Bit 7-0 6 UPPER_THRE SHOLD_2_DAT A6 Name 5 UPPER_THRE SHOLD_2_DAT A5 4 UPPER_THRE SHOLD_2_DAT A4 3 UPPER_THRE SHOLD_2_DAT A3 2 UPPER_THRE SHOLD_2_DAT A2 Description 1 UPPER_THRE SHOLD_2_DAT A1 0 UPPER_THRE SHOLD_2_DAT A0 These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumuUPPER_THRESHOLD_2_DATA[7:0] lated events is above this threshold, a no-activity alarm is raised. Programming Information 105 June 19, 2006 IDT82V3280 WAN PLL LOWER_THRESHOLD_2_CNFG - Lower Threshold for Leaky Bucket Configuration 2 Address: 3AH Type: Read / Write Default Value: 00000100 7 LOWER_THRE SHOLD_2_DAT A7 Bit 7-0 6 LOWER_THRE SHOLD_2_DAT A6 Name LOWER_THRESHOLD_2_DATA[7:0] 5 LOWER_THRE SHOLD_2_DAT A5 4 LOWER_THRE SHOLD_2_DAT A4 3 LOWER_THRE SHOLD_2_DAT A3 2 LOWER_THRE SHOLD_2_DAT A2 Description These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated events is below this threshold, the no-activity alarm is cleared. 1 LOWER_THRE SHOLD_2_DAT A1 0 LOWER_THRE SHOLD_2_DAT A0 BUCKET_SIZE_2_CNFG - Bucket Size for Leaky Bucket Configuration 2 Address: 3BH Type: Read / Write Default Value: 00001000 7 BUCKET_SIZE _2_DATA7 Bit 7-0 6 BUCKET_SIZE _2_DATA6 Name BUCKET_SIZE_2_DATA[7:0] 5 BUCKET_SIZE _2_DATA5 4 BUCKET_SIZE _2_DATA4 3 BUCKET_SIZE _2_DATA3 2 BUCKET_SIZE _2_DATA2 1 BUCKET_SIZE _2_DATA1 0 BUCKET_SIZE _2_DATA0 Description These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach the bucket size, the accumulator will stop increasing even if further events are detected. DECAY_RATE_2_CNFG - Decay Rate for Leaky Bucket Configuration 2 Address: 3CH Type: Read / Write Default Value: XXXXXX01 7 Bit 7-2 6 Name 5 4 3 Description 2 1 DECAY_RATE_ 2_DATA1 0 DECAY_RATE_ 2_DATA0 1-0 Reserved. These bits set a decay rate for the internal leaky bucket accumulator: 00: The accumulator decreases by 1 in every 128 ms with no event detected. DECAY_RATE_2_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default) 10: The accumulator decreases by 1 in every 512 ms with no event detected. 11: The accumulator decreases by 1 in every 1024 ms with no event detected. Programming Information 106 June 19, 2006 IDT82V3280 WAN PLL UPPER_THRESHOLD_3_CNFG - Upper Threshold for Leaky Bucket Configuration 3 Address: 3DH Type: Read / Write Default Value: 00000110 7 UPPER_THRE SHOLD_3_DAT A7 Bit 7-0 6 UPPER_THRE SHOLD_3_DAT A6 Name UPPER_THRESHOLD_3_DATA[7:0] 5 UPPER_THRE SHOLD_3_DAT A5 4 UPPER_THRE SHOLD_3_DAT A4 3 UPPER_THRE SHOLD_3_DAT A3 2 UPPER_THRE SHOLD_3_DAT A2 Description These bits set an upper threshold for the internal leaky bucket accumulator. When the number of the accumulated events is above this threshold, a no-activity alarm is raised. 1 UPPER_THRE SHOLD_3_DAT A1 0 UPPER_THRE SHOLD_3_DAT A0 LOWER_THRESHOLD_3_CNFG - Lower Threshold for Leaky Bucket Configuration 3 Address: 3EH Type: Read / Write Default Value: 00000100 7 LOWER_THRE SHOLD_3_DAT A7 Bit 7-0 6 LOWER_THRE SHOLD_3_DAT A6 Name LOWER_THRESHOLD_3_DATA[7:0] 5 LOWER_THRE SHOLD_3_DAT A5 4 LOWER_THRE SHOLD_3_DAT A4 3 LOWER_THRE SHOLD_3_DAT A3 2 LOWER_THRE SHOLD_3_DAT A2 Description These bits set a lower threshold for the internal leaky bucket accumulator. When the number of the accumulated events is below this threshold, the no-activity alarm is cleared. 1 LOWER_THRE SHOLD_3_DAT A1 0 LOWER_THRE SHOLD_3_DAT A0 BUCKET_SIZE_3_CNFG - Bucket Size for Leaky Bucket Configuration 3 Address: 3FH Type: Read / Write Default Value: 00001000 7 BUCKET_SIZE _3_DATA7 Bit 7-0 6 BUCKET_SIZE _3_DATA6 Name BUCKET_SIZE_3_DATA[7:0] 5 BUCKET_SIZE _3_DATA5 4 BUCKET_SIZE _3_DATA4 3 BUCKET_SIZE _3_DATA3 2 BUCKET_SIZE _3_DATA2 1 BUCKET_SIZE _3_DATA1 0 BUCKET_SIZE _3_DATA0 Description These bits set a bucket size for the internal leaky bucket accumulator. If the number of the accumulated events reach the bucket size, the accumulator will stop increasing even if further events are detected. Programming Information 107 June 19, 2006 IDT82V3280 WAN PLL DECAY_RATE_3_CNFG - Decay Rate for Leaky Bucket Configuration 3 Address: 40H Type: Read / Write Default Value: XXXXXX01 7 Bit 7-2 6 Name 5 4 3 Description 2 1 DECAY_RATE_ 3_DATA1 0 DECAY_RATE_ 3_DATA0 1-0 Reserved. These bits set a decay rate for the internal leaky bucket accumulator: 00: The accumulator decreases by 1 in every 128 ms with no event detected. DECAY_RATE_3_DATA[1:0] 01: The accumulator decreases by 1 in every 256 ms with no event detected. (default) 10: The accumulator decreases by 1 in every 512 ms with no event detected. 11: The accumulator decreases by 1 in every 1024 ms with no event detected. IN_FREQ_READ_CH_CNFG - Input Clock Frequency Read Channel Selection Address: 41H Type: Read / Write Default Value: XXXX0000 7 Bit 7-4 6 Name 5 4 3 IN_FREQ_READ _CH3 2 IN_FREQ_READ _CH2 Description 1 IN_FREQ_READ _CH1 0 IN_FREQ_READ _CH0 3-0 Reserved. These bits select an input clock, the frequency of which with respect to the reference clock can be read. 0000: Reserved. (default) 0001: IN1. 0010: IN2. IN_FREQ_READ_CH[3:0] ...... 1101: IN13. 1110: IN14. 1111: Reserved. Programming Information 108 June 19, 2006 IDT82V3280 WAN PLL IN_FREQ_READ_STS - Input Clock Frequency Read Value Address: 42H Type: Read Default Value: 00000000 7 IN_FREQ_VAL UE7 Bit 7-0 6 IN_FREQ_VAL UE6 Name 5 IN_FREQ_VAL UE5 4 IN_FREQ_VAL UE4 3 IN_FREQ_VAL UE3 2 IN_FREQ_VAL UE2 1 IN_FREQ_VAL UE1 0 IN_FREQ_VAL UE0 Description These bits represent a 2's complement signed integer. If the value is multiplied by the value in the FREQ_MON_FACTOR[3:0] bits (b3~0, 2EH), the frequency of an input clock with respect to the reference clock in ppm will IN_FREQ_VALUE[7:0] be gotten. The input clock is selected by the IN_FREQ_READ_CH[3:0] bits (b3~0, 41H). The value in these bits is updated every 16 seconds, starting when an input clock is selected. IN1_IN2_STS - Input Clock 1 & 2 Status Address: 43H Type: Read Default Value: X110X110 7 Bit 7 6 6 IN2_FREQ_HA RD_ALARM Name IN2_FREQ_HARD_ALARM 5 IN2_NO_ACTIV ITY_ALARM 4 IN2_PH_LOCK _ALARM 3 2 IN1_FREQ_HA RD_ALARM Description Reserved. This bit indicates whether IN2 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN2 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN2 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN1 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN1 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN1 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 1 IN1_NO_ACTIV ITY_ALARM 0 IN1_PH_LOCK _ALARM 5 IN2_NO_ACTIVITY_ALARM 4 IN2_PH_LOCK_ALARM 3 2 IN1_FREQ_HARD_ALARM 1 IN1_NO_ACTIVITY_ALARM 0 IN1_PH_LOCK_ALARM Programming Information 109 June 19, 2006 IDT82V3280 WAN PLL IN3_IN4_STS - Input Clock 3 & 4 Status Address: 44H Type: Read Default Value: X110X110 7 6 IN4_FREQ_HAR D_ALARM 5 IN4_NO_ACTIVI TY_ALARM 4 IN4_PH_LOCK_ ALARM 3 2 IN3_FREQ_HAR D_ALARM 1 IN3_NO_ACTIVI TY_ALARM 0 IN3_PH_LOCK_ ALARM Bit 7 6 Name IN4_FREQ_HARD_ALARM Description Reserved. This bit indicates whether IN4 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN4 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN4 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN3 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN3 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN3 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 5 IN4_NO_ACTIVITY_ALARM 4 IN4_PH_LOCK_ALARM 3 2 IN3_FREQ_HARD_ALARM 1 IN3_NO_ACTIVITY_ALARM 0 IN3_PH_LOCK_ALARM Programming Information 110 June 19, 2006 IDT82V3280 WAN PLL IN5_IN6_STS - Input Clock 5 & 6 Status Address: 45H Type: Read Default Value: X110X110 7 Bit 7 6 6 IN6_FREQ_HAR D_ALARM Name IN6_FREQ_HARD_ALARM 5 IN6_NO_ACTIVI TY_ALARM 4 IN6_PH_LOCK_ ALARM 3 2 IN5_FREQ_HAR D_ALARM Description Reserved. This bit indicates whether IN6 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN6 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN6 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN5 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN5 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN5 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 1 IN5_NO_ACTIVI TY_ALARM 0 IN5_PH_LOCK_ ALARM 5 IN6_NO_ACTIVITY_ALARM 4 IN6_PH_LOCK_ALARM 3 2 IN5_FREQ_HARD_ALARM 1 IN5_NO_ACTIVITY_ALARM 0 IN5_PH_LOCK_ALARM Programming Information 111 June 19, 2006 IDT82V3280 WAN PLL IN7_IN8_STS - Input Clock 7 & 8 Status Address: 46H Type: Read Default Value: X110X110 7 Bit 7 6 6 IN8_FREQ_HA RD_ALARM Name IN8_FREQ_HARD_ALARM 5 IN8_NO_ACTIV ITY_ALARM 4 IN8_PH_LOCK _ALARM 3 2 IN7_FREQ_HA RD_ALARM Description Reserved. This bit indicates whether IN8 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN8 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN8 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN7 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN7 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN7 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 1 IN7_NO_ACTIV ITY_ALARM 0 IN7_PH_LOCK _ALARM 5 IN8_NO_ACTIVITY_ALARM 4 IN8_PH_LOCK_ALARM 3 2 IN7_FREQ_HARD_ALARM 1 IN7_NO_ACTIVITY_ALARM 0 IN7_PH_LOCK_ALARM Programming Information 112 June 19, 2006 IDT82V3280 WAN PLL IN9_IN10_STS - Input Clock 9 & 10 Status Address: 47H Type: Read Default Value: X110X110 7 6 IN10_FREQ_HA RD_ALARM 5 IN10_NO_ACTI VITY_ALARM 4 IN10_PH_LOCK _ALARM 3 2 IN9_FREQ_HAR D_ALARM 1 IN9_NO_ACTIVI TY_ALARM 0 IN9_PH_LOCK_ ALARM Bit 7 6 Name IN10_FREQ_HARD_ALARM Description Reserved. This bit indicates whether IN10 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN10 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN10 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN9 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN9 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN9 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 5 IN10_NO_ACTIVITY_ALARM 4 IN10_PH_LOCK_ALARM 3 2 IN9_FREQ_HARD_ALARM 1 IN9_NO_ACTIVITY_ALARM 0 IN9_PH_LOCK_ALARM Programming Information 113 June 19, 2006 IDT82V3280 WAN PLL IN11_IN12_STS - Input Clock 11 & 12 Status Address: 48H Type: Read Default Value: X110X110 7 Bit 7 6 6 IN12_FREQ_H ARD_ALARM Name IN12_FREQ_HARD_ALARM 5 IN12_NO_ACTI VITY_ALARM 4 IN12_PH_LOC K_ALARM 3 2 IN11_FREQ_H ARD_ALARM Description Reserved. This bit indicates whether IN12 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN12 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN12 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN11 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN11 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN11 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 1 IN11_NO_ACTI VITY_ALARM 0 IN11_PH_LOCK _ALARM 5 IN12_NO_ACTIVITY_ALARM 4 IN12_PH_LOCK_ALARM 3 2 IN11_FREQ_HARD_ALARM 1 IN11_NO_ACTIVITY_ALARM 0 IN11_PH_LOCK_ALARM Programming Information 114 June 19, 2006 IDT82V3280 WAN PLL IN13_IN14_STS - Input Clock 13 & 14 Status Address: 49H Type: Read Default Value: X110X110 7 Bit 7 6 6 IN14_FREQ_H ARD_ALARM Name IN14_FREQ_HARD_ALARM 5 IN14_NO_ACTI VITY_ALARM 4 IN14_PH_LOC K_ALARM 3 2 IN13_FREQ_H ARD_ALARM Description Reserved. This bit indicates whether IN14 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN14 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN14 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. Reserved. This bit indicates whether IN13 is in frequency hard alarm status. 0: No frequency hard alarm. 1: In frequency hard alarm status. (default) This bit indicates whether IN13 is in no-activity alarm status. 0: No no-activity alarm. 1: In no-activity alarm status. (default) This bit indicates whether IN13 is in phase lock alarm status. 0: No phase lock alarm. (default) 1: In phase lock alarm status. If the PH_ALARM_TIMEOUT bit (b5, 09H) is `0', this bit is cleared by writing `1' to this bit; if the PH_ALARM_TIMEOUT bit (b5, 09H) is `1', this bit is cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0] (b7~6, 08H) in second) which starts from when the alarm is raised. 1 IN13_NO_ACTI VITY_ALARM 0 IN13_PH_LOC K_ALARM 5 IN14_NO_ACTIVITY_ALARM 4 IN14_PH_LOCK_ALARM 3 2 IN13_FREQ_HARD_ALARM 1 IN13_NO_ACTIVITY_ALARM 0 IN13_PH_LOCK_ALARM Programming Information 115 June 19, 2006 IDT82V3280 WAN PLL 7.2.5 T0 / T4 DPLL INPUT CLOCK SELECTION REGISTERS INPUT_VALID1_STS - Input Clocks Validity 1 Address: 4AH Type: Read Default Value: 00000000 7 IN8 Bit 7-0 Name INn 6 IN7 5 IN6 4 IN5 3 IN4 Description This bit indicates the validity of the corresponding INn. Here n is any one of 8 to 1. 0: Invalid. (default) 1: Valid. 2 IN3 1 IN2 0 IN1 INPUT_VALID2_STS - Input Clocks Validity 2 Address: 4BH Type: Read Default Value: XX000000 7 Bit 7-6 5-0 Name INn 6 5 IN14 4 IN13 3 IN12 Description Reserved. This bit indicates the validity of the corresponding INn. Here n is any one of 14 to 9. 0: Invalid. (default) 1: Valid. 2 IN11 1 IN10 0 IN9 REMOTE_INPUT_VALID1_CNFG - Input Clocks Validity Configuration 1 Address: 4CH Type: Read / Write Default Value: 11111111 7 IN8_VALID Bit 7-0 6 IN7_VALID Name INn_VALID 5 IN6_VALID 4 IN5_VALID 3 IN4_VALID Description This bit controls whether the corresponding INn is allowed to be locked for automatic selection. Here n is any one of 8 to 1. 0: Enabled. 1: Disabled. (default) 2 IN3_VALID 1 IN2_VALID 0 IN1_VALID Programming Information 116 June 19, 2006 IDT82V3280 WAN PLL REMOTE_INPUT_VALID2_CNFG - Input Clocks Validity Configuration 2 Address: 4DH Type: Read / Write Default Value: XX111111 7 Bit 7-6 5-0 Name INn_VALID 6 5 IN14_VALID 4 IN13_VALID 3 IN12_VALID 2 IN11_VALID 1 IN10_VALID 0 IN9_VALID Description Reserved. This bit controls whether the corresponding INn is allowed to be locked for automatic selection. Here n is any one of 14 to 9. 0: Enabled. 1: Disabled. (default) PRIORITY_TABLE1_STS - Priority Status 1 * Address: 4EH Type: Read Default Value: 00000000 7 HIGHEST_PRI ORITY_VALIDA TED3 Bit 6 HIGHEST_PRI ORITY_VALIDA TED2 Name 5 HIGHEST_PRI ORITY_VALIDA TED1 4 HIGHEST_PRI ORITY_VALIDA TED0 3 CURRENTLY_S ELECTED_INP UT3 2 CURRENTLY_S ELECTED_INP UT2 Description 1 CURRENTLY_S ELECTED_INP UT1 0 CURRENTLY_S ELECTED_INP UT0 7-4 3-0 These bits indicate a qualified input clock with the highest priority. 0000: No input clock is qualified. (default) 0001: IN1. 0010: IN2. ...... HIGHEST_PRIORITY_VALIDATED[3:0] 1101: IN13. 1110: IN14. 1111: Reserved. Note that the input clock is indicated by these bits only when the corresponding INn (b7-0, 4CH) or INn (b5-0, 4DH) bit is `0'. These bits indicate the T0/T4 selected input clock. 0000: No input clock is selected; or the T4 selected input clock is the T0 DPLL output. (default) 0001: IN1 is selected. 0010: IN2 is selected. ...... CURRENTLY_SELECTED_INPUT[3:0] 1101: IN13 is selected. 1110: IN14 is selected. 1111: Reserved. Note that the input clock is indicated by these bits only when the corresponding INn (b7-0, 4CH) or INn (b5-0, 4DH) bit is `0'. Programming Information 117 June 19, 2006 IDT82V3280 WAN PLL PRIORITY_TABLE2_STS - Priority Status 2 * Address: 4FH Type: Read Default Value: 00000000 7 THIRD_HIGHE ST_PRIORITY_ VALIDATED3 Bit 6 THIRD_HIGHE ST_PRIORITY_ VALIDATED2 5 THIRD_HIGHE ST_PRIORITY_ VALIDATED1 Name 4 THIRD_HIGHE ST_PRIORITY_ VALIDATED0 3 SECOND_HIGH EST_PRIORITY _VALIDATED3 2 SECOND_HIGH EST_PRIORITY _VALIDATED2 Description 1 SECOND_HIGH EST_PRIORITY _VALIDATED1 0 SECOND_HIGH EST_PRIORITY _VALIDATED0 7-4 3-0 These bits indicate a qualified input clock with the third highest priority. 0000: No input clock is qualified. (default) 0001: IN1. 0010: IN2. ...... THIRD_HIGHEST_PRIORITY_VALIDATED[3:0] 1101: IN13. 1110: IN14. 1111: Reserved. Note that the input clock is indicated by these bits only when the corresponding INn (b7-0, 4CH) or INn (b5-0, 4DH) bit is `0'. These bits indicate a qualified input clock with the second highest priority. 0000: No input clock is qualified. (default) 0001: IN1. 0010: IN2. ...... SECOND_HIGHEST_PRIORITY_VALIDATED[3:0] 1101: IN13. 1110: IN14. 1111: Reserved. Note that the input clock is indicated by these bits only when the corresponding INn (b7-0, 4CH) or INn (b5-0, 4DH) bit is `0'. T0_INPUT_SEL_CNFG - T0 Selected Input Clock Configuration Address: 50H Type: Read / Write Default Value: XXXX0000 7 Bit 7-4 6 Name 5 4 3 T0_INPUT_SEL3 2 T0_INPUT_SEL2 1 T0_INPUT_SEL1 0 T0_INPUT_SEL0 Description 3-0 Reserved. This bit determines T0 input clock selection. It is valid only when the EXT_SW bit (b4, 0BH) is `0'. 0000: Automatic selection. (default) 0001: Forced selection - IN1 is selected. 0010: Forced selection - IN2 is selected. T0_INPUT_SEL[3:0] ...... 1101: Forced selection - IN13 is selected. 1110: Forced selection - IN14 is selected. 1111: Reserved. Programming Information 118 June 19, 2006 IDT82V3280 WAN PLL T4_INPUT_SEL_CNFG - T4 Selected Input Clock Configuration Address: 51H Type: Read / Write Default Value: X0000000 7 Bit 7 6 6 T4_LOCK_T0 Name 5 T0_FOR_T4 4 T4_TEST_T0_PH 3 T4_INPUT_SEL3 2 T4_INPUT_SEL2 1 T4_INPUT_SEL1 0 T4_INPUT_SEL0 Description 5 4 3-0 Reserved. This bit determines whether the T4 DPLL locks to a T0 DPLL output or locks independently from the T0 DPLL. T4_LOCK_T0 0: Independently from the T0 path. (default) 1: Locks to a 77.76 MHz or 8 kHz signal from the T0 DPLL 77.76 MHz path. This bit is valid only when the T4_LOCK_T0 bit (b6, 51H) is `1'. It determines whether a 77.76 MHz or 8 kHz signal from the T0 DPLL 77.76 MHz path is selected by the T4 DPLL. T0_FOR_T4 0: 77.76 MHz. (default) 1: 8 kHz. This bit determines whether T4 selected input clock is compared with the feedback signal of the T4 DPLL for T4 DPLL locking or is compared with the T0 selected input clock to get the phase difference between T0 and T4 selected input clocks. T4_TEST_T0_PH 0: The T4 DPLL output. (default) 1: The T0 selected input clock. These bits are valid only when the T4_LOCK_T0 bit (b6, 51H) is `0'. They determines the T4 DPLL input clock selection. 0000: Automatic selection. (default) 0001: Forced selection - IN1 is selected. 0010: Forced selection - IN2 is selected. T4_INPUT_SEL[3:0] ...... 1101: Forced selection - IN13 is selected. 1110: Forced selection - IN14 is selected. 1111: Reserved. Programming Information 119 June 19, 2006 IDT82V3280 WAN PLL 7.2.6 T0 / T4 DPLL STATE MACHINE CONTROL REGISTERS OPERATING_STS - DPLL Operating Status Address: 52H Type: Read Default Value: 10000001 7 EX_SYNC_ALA RM_MON Bit 7 6 T4_DPLL_LO CK Name EX_SYNC_ALARM_MON 5 T0_DPLL_SOFT _FREQ_ALARM 4 T4_DPLL_SOFT _FREQ_ALARM 3 T0_DPLL_LO CK 2 T0_DPLL_OPER ATING_MODE2 Description 1 T0_DPLL_OPER ATING_MODE1 0 T0_DPLL_OPER ATING_MODE0 6 5 4 3 2-0 This bit indicates whether the frame sync input signal is in external sync alarm status. 0: No external sync alarm. 1: In external sync alarm status. (default) This bit indicates the T4 DPLL locking status. T4_DPLL_LOCK 0: Unlocked. (default) 1: Locked. This bit indicates whether the T0 DPLL is in soft alarm status. T0_DPLL_SOFT_FREQ_ALARM 0: No T0 DPLL soft alarm. (default) 1: In T0 DPLL soft alarm status. This bit indicates whether the T4 DPLL is in soft alarm status. T4_DPLL_SOFT_FREQ_ALARM 0: No T4 DPLL soft alarm. (default) 1: In T4 DPLL soft alarm status. This bit indicates the T0 DPLL locking status. T0_DPLL_LOCK 0: Unlocked. (default) 1: Locked. These bits indicate the current operating mode of T0 DPLL. 000: Reserved. 001: Free-Run. (default) 010: Holdover. T0_DPLL_OPERATING_MODE[2:0] 011: Reserved. 100: Locked. 101: Pre-Locked2. 110: Pre-Locked. 111: Lost-Phase. Programming Information 120 June 19, 2006 IDT82V3280 WAN PLL T0_OPERATING_MODE_CNFG - T0 DPLL Operating Mode Configuration Address: 53H Type: Read / Write Default Value: XXXXX000 7 Bit 7-3 6 Name Reserved. These bits control the T0 DPLL operating mode. 000: Automatic. (default) 001: Forced - Free-Run. 010: Forced - Holdover. T0_OPERATING_MODE[2:0] 011: Reserved. 100: Forced - Locked. 101: Forced - Pre-Locked2. 110: Forced - Pre-Locked. 111: Forced - Lost-Phase. 5 4 3 2 T0_OPERATING_MODE2 1 T0_OPERATING_MODE1 Description 0 T0_OPERATING_MODE0 2-0 T4_OPERATING_MODE_CNFG - T4 DPLL Operating Mode Configuration Address: 54H Type: Read / Write Default Value: XXXXX000 7 Bit 7-3 6 Name Reserved. These bits control the T4 DPLL operating mode. 000: Automatic. (default) 001: Forced - Free-Run. T4_OPERATING_MODE[2:0] 010: Forced - Holdover. 011: Reserved. 100: Forced - Locked. 101, 110, 111: Reserved. 5 4 3 2 T4_OPERATING_MODE2 1 T4_OPERATING_MODE1 Description 0 T4_OPERATING_MODE0 2-0 Programming Information 121 June 19, 2006 IDT82V3280 WAN PLL 7.2.7 T0 / T4 DPLL & APLL CONFIGURATION REGISTERS T0_DPLL_APLL_PATH_CNFG - T0 DPLL & APLL Path Configuration Address: 55H Type: Read / Write Default Value: 00000X0X 7 T0_APLL_PATH 3 Bit 6 T0_APLL_PA TH2 Name 5 T0_APLL_PA TH1 4 T0_APLL_PA TH0 3 T0_GSM_OBSAI_ 16E1_16T1_SEL1 2 T0_GSM_OBSAI_ 16E1_16T1_SEL0 Description 1 T0_12E1_24T1_ E3_T3_SEL1 0 T0_12E1_24T1_ E3_T3_SEL0 7-4 3-2 1-0 These bits select an input to the T0 APLL. 0000: The output of T0 DPLL 77.76 MHz path. (default) 0001: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0010: The output of T0 DPLL 16E1/16T1 path. 0011: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. T0_APLL_PATH[3:0] 0100: The output of T4 DPLL 77.76 MHz path. 0101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T4 DPLL 16E1/16T1 path. 0111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. 1XXX: Reserved. These bits select an output clock from the T0 DPLL GSM/OBSAI/16E1/16T1 path. 00: 16E1. 01: 16T1. T0_GSM_OBSAI_16E1_16T1_SEL[1:0] 10: GSM. 11: OBSAI. The default value of the T0_GSM_OBSAI_16E1_16T1_SEL0 bit is determined by the SONET/SDH pin during reset. These bits select an output clock from the T0 DPLL 12E1/24T1/E3/T3 path. 00: 12E1. 01: 24T1. 10: E3. T0_12E1_24T1_E3_T3_SEL[1:0] 11: T3. The default value of the T0_12E1_24T1_E3_T3_SEL0 bit is determined by the SONET/SDH pin during reset. Programming Information 122 June 19, 2006 IDT82V3280 WAN PLL T0_DPLL_START_BW_DAMPING_CNFG - T0 DPLL Start Bandwidth & Damping Factor Configuration Address: 56H Type: Read / Write Default Value: 01101111 7 T0_DPLL_STA RT_DAMPING2 Bit 6 T0_DPLL_STA RT_DAMPING1 Name 5 T0_DPLL_STA RT_DAMPING0 4 T0_DPLL_STA RT_BW4 3 T0_DPLL_STA RT_BW3 2 T0_DPLL_STA RT_BW2 Description 1 T0_DPLL_STA RT_BW1 0 T0_DPLL_STA RT_BW0 7-5 4-0 These bits set the starting damping factor for T0 DPLL. 000: Reserved. 001: 1.2. 010: 2.5. T0_DPLL_START_DAMPING[2:0] 011: 5. (default) 100: 10. 101: 20. 110, 111: Reserved. These bits set the starting bandwidth for T0 DPLL. 00000: 0.5 mHz. 00001: 1 mHz. 00010: 2 mHz. 00011: 4 mHz. 00100: 8 mHz. 00101: 15 mHz. 00110: 30 mHz. 00111: 60 mHz. 01000: 0.1 Hz. 01001: 0.3 Hz. T0_DPLL_START_BW[4:0] 01010: 0.6 Hz. 01011: 1.2 Hz. 01100: 2.5 Hz. 01101: 4 Hz. 01110: 8 Hz. 01111: 18 Hz. (default) 10000: 35 Hz. 10001: 70 Hz. 10010: 560 Hz. 10011 ~ 11111: Reserved. Programming Information 123 June 19, 2006 IDT82V3280 WAN PLL T0_DPLL_ACQ_BW_DAMPING_CNFG - T0 DPLL Acquisition Bandwidth & Damping Factor Configuration Address: 57H Type: Read / Write Default Value: 01101111 7 T0_DPLL_ACQ _DAMPING2 Bit 6 T0_DPLL_ACQ _DAMPING1 Name 5 T0_DPLL_ACQ _DAMPING0 4 T0_DPLL_ACQ _BW4 3 T0_DPLL_ACQ _BW3 2 T0_DPLL_ACQ _BW2 Description 1 T0_DPLL_ACQ _BW1 0 T0_DPLL_ACQ _BW0 7-5 4-0 These bits set the acquisition damping factor for T0 DPLL. 000: Reserved. 001: 1.2. 010: 2.5. T0_DPLL_ACQ_DAMPING[2:0] 011: 5. (default) 100: 10. 101: 20. 110, 111: Reserved. These bits set the acquisition bandwidth for T0 DPLL. 00000: 0.5 mHz. 00001: 1 mHz. 00010: 2 mHz. 00011: 4 mHz. 00100: 8 mHz. 00101: 15 mHz. 00110: 30 mHz. 00111: 60 mHz. 01000: 0.1 Hz. 01001: 0.3 Hz. T0_DPLL_ACQ_BW[4:0] 01010: 0.6 Hz. 01011: 1.2 Hz. 01100: 2.5 Hz. 01101: 4 Hz. 01110: 8 Hz. 01111: 18 Hz. (default) 10000: 35 Hz. 10001: 70 Hz. 10010: 560 Hz. 10011 ~ 11111: Reserved. Programming Information 124 June 19, 2006 IDT82V3280 WAN PLL T0_DPLL_LOCKED_BW_DAMPING_CNFG - T0 DPLL Locked Bandwidth & Damping Factor Configuration Address: 58H Type: Read / Write Default Value: 01101011 7 T0_DPLL_LOCK ED_DAMPING2 Bit 6 T0_DPLL_LOCK ED_DAMPING1 Name 5 T0_DPLL_LOCK ED_DAMPING0 4 T0_DPLL_LOC KED_BW4 3 T0_DPLL_LOC KED_BW3 2 T0_DPLL_LOC KED_BW2 Description 1 T0_DPLL_LOC KED_BW1 0 T0_DPLL_LOC KED_BW0 7-5 4-0 These bits set the locked damping factor for T0 DPLL. 000: Reserved. 001: 1.2. 010: 2.5. T0_DPLL_LOCKED_DAMPING[2:0] 011: 5. (default) 100: 10. 101: 20. 110, 111: Reserved. These bits set the locked bandwidth for T0 DPLL. 00000: 0.5 mHz. 00001: 1 mHz. 00010: 2 mHz. 00011: 4 mHz. 00100: 8 mHz. 00101: 15 mHz. 00110: 30 mHz. 00111: 60 mHz. 01000: 0.1 Hz. 01001: 0.3 Hz. T0_DPLL_LOCKED_BW[4:0] 01010: 0.6 Hz. 01011: 1.2 Hz. (default) 01100: 2.5 Hz. 01101: 4 Hz. 01110: 8 Hz. 01111: 18 Hz. 10000: 35 Hz. 10001: 70 Hz. 10010: 560 Hz. 10011 ~ 11111: Reserved. Programming Information 125 June 19, 2006 IDT82V3280 WAN PLL T0_BW_OVERSHOOT_CNFG - T0 DPLL Bandwidth Overshoot Configuration Address: 59H Type: Read / Write Default Value: 1XXX1XXX 7 AUTO_BW_SEL Bit Name 6 5 4 3 T0_LIMT Description 2 1 0 - 7 6-4 3 2-0 This bit determines whether starting or acquisition bandwidth / damping factor is used for T0 DPLL. 0: The starting and acquisition bandwidths / damping factors are not used. Only the locked bandwidth / damping factor is used AUTO_BW_SEL regardless of the T0 DPLL locking stage. 1: The starting, acquisition or locked bandwidth / damping factor is used automatically depending on different T0 DPLL locking stages. (default) Reserved. This bit determines whether the integral path value is frozen when the T0 DPLL hard limit is reached. T0_LIMT 0: Not frozen. 1: Frozen. It will minimize the subsequent overshoot when T0 DPLL is pulling in. (default) Reserved. Programming Information 126 June 19, 2006 IDT82V3280 WAN PLL PHASE_LOSS_COARSE_LIMIT_CNFG - Phase Loss Coarse Detector Limit Configuration * Address: 5AH Type: Read / Write Default Value: 10000101 7 COARSE_PH_L OS_LIMT_EN Bit 7 6 Name 6 WIDE_EN 5 MULTI_PH_APP 4 MULTI_PH_8K_ 4K_2K_EN 3 PH_LOS_COA RSE_LIMT3 2 PH_LOS_COA RSE_LIMT2 1 PH_LOS_COA RSE_LIMT1 0 PH_LOS_COA RSE_LIMT0 Description 5 This bit controls whether the occurrence of the coarse phase loss will result in the T0/T4 DPLL unlocked. COARSE_PH_LOS_LIMT_EN 0: Disabled. 1: Enabled. (default) WIDE_EN Refer to the description of the MULTI_PH_8K_4K_2K_EN bit (b4, 5AH). This bit determines whether the PFD output of T0/T4 DPLL is limited to 1 UI or is limited to the coarse phase limit. 0: Limited to 1 UI. (default) 1: Limited to the coarse phase limit. When the selected input clock is of 2 kHz, 4 kHz or 8 kHz, the coarse phase limit depends MULTI_PH_APP on the MULTI_PH_8K_4K_2K_EN bit, the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits; when the selected input clock is of other frequencies but 2 kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to the description of the MULTI_PH_8K_4K_2K_EN bit (b4, 5AH) for details. This bit, together with the WIDE_EN bit (b6, 5AH) and the PH_LOS_COARSE_LIMT[3:0] bits (b3~0, 5AH), determines the coarse phase limit when the selected input clock is of 2 kHz, 4 kHz or 8 kHz. When the selected input clock is of other frequencies but 2 kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits. Selected Input Clock MULTI_PH_8K_4K_2K_EN WIDE_EN Coarse Phase Limit 1 UI 1 UI set by the PH_LOS_COARSE_LIMT[3:0] bits (b3~0, 5AH). 1 UI set by the PH_LOS_COARSE_LIMT[3:0] bits (b3~0, 5AH). 4 MULTI_PH_8K_4K_2K_EN 2 kHz, 4 kHz or 8 kHz 0 1 don't-care 0 1 0 other than 2 kHz, 4 kHz and 8 kHz don't-care 1 These bit set the coarse phase limit. The limit is used only in some cases. Refer to the description of the MULTI_PH_8K_4K_2K_EN bit (b4, 5AH). 0000: 1 UI. 0001: 3 UI. 0010: 7 UI. 0011: 15 UI. 3 - 0 PH_LOS_COARSE_LIMT[3:0] 0100: 31 UI. 0101: 63 UI. (default) 0110: 127 UI. 0111: 255 UI. 1000: 511 UI. 1001: 1023 UI (T0); Reserved (T4). 1010-1111: Reserved. Programming Information 127 June 19, 2006 IDT82V3280 WAN PLL PHASE_LOSS_FINE_LIMIT_CNFG - Phase Loss Fine Detector Limit Configuration * Address: 5BH Type: Read / Write Default Value: 10XXX010 7 FINE_PH_LOS_ LIMT_EN Bit 7 6 FAST_LOS_SW Name 5 4 3 2 PH_LOS_FINE _LIMT2 Description 1 PH_LOS_FINE _LIMT1 0 PH_LOS_FINE _LIMT0 6 5-3 2-0 This bit controls whether the occurrence of the fine phase loss will result in the T0/T4 DPLL unlocked. FINE_PH_LOS_LIMT_EN 0: Disabled. 1: Enabled. (default) The value in this bit can be switched only when it is available for T0 path; this bit is always `1' when it is available for T4 path. This bit controls whether the occurrence of the fast loss will result in the T0/T4 DPLL unlocked. FAST_LOS_SW 0: Does not result in the T0 DPLL unlocked. T0 DPLL will enter Temp-Holdover mode automatically. (default) 1: Results in the T0/T4 DPLL unlocked. For T0 path, T0 DPLL will enter Lost-Phase mode if the T0 DPLL operating mode is switched automatically. Reserved. These bits set a fine phase limit. 000: 0. 001: (45 ~ 90 ). 010: (90 ~ 180 ). (default) PH_LOS_FINE_LIMT[2:0] 011: (180 ~ 360 ). 100: (20 ns ~ 25 ns). 101: (60 ns ~ 65 ns). 110: (120 ns ~ 125 ns). 111: (950 ns ~ 955 ns). Programming Information 128 June 19, 2006 IDT82V3280 WAN PLL T0_HOLDOVER_MODE_CNFG - T0 DPLL Holdover Mode Configuration Address: 5CH Type: Read / Write Default Value: 010001XX 7 MAN_HOLDOV ER Bit 7 6 6 AUTO_AVG Name MAN_HOLDOVER AUTO_AVG 5 FAST_AVG 4 READ_AVG 3 TEMP_HOLDO VER_MODE1 2 TEMP_HOLDO VER_MODE0 Description Refer to the description of the FAST_AVG bit (b5, 5CH). Refer to the description of the FAST_AVG bit (b5, 5CH). This bit, together with the AUTO_AVG bit (b6, 5CH) and the MAN_HOLDOVER bit (b7, 5CH), determines a frequency offset acquiring method in T0 DPLL Holdover Mode. MAN_HOLDOVER 5 FAST_AVG 0 1 AUTO_AVG 0 1 don't-care FAST_AVG don't-care 0 1 Frequency Offset Acquiring Method Automatic Instantaneous Automatic Slow Averaged (default) Automatic Fast Averaged Manual 1 0 - 4 3-2 1-0 This bit controls the holdover frequency offset reading, which is read from the T0_HOLDOVER_FREQ[23:0] bits (5FH ~ 5DH). 0: The value read from the T0_HOLDOVER_FREQ[23:0] bits (5FH ~ 5DH) is equal to the one written to them. (default) READ_AVG 1: The value read from the T0_HOLDOVER_FREQ[23:0] bits (5FH ~ 5DH) is not equal to the one written to them. The value is acquired by Automatic Slow Averaged method if the FAST_AVG bit (b5, 5CH) is `0'; or is acquired by Automatic Fast Averaged method if the FAST_AVG bit (b5, 5CH) is `1'. These bits determine the frequency offset acquiring method in T0 DPLL Temp-Holdover Mode. 00: The method is the same as that used in T0 DPLL Holdover mode. TEMP_HOLDOVER_MODE[1:0] 01: Automatic Instantaneous. (default) 10: Automatic Fast Averaged. 11: Automatic Slow Averaged. Reserved. T0_HOLDOVER_FREQ[7:0]_CNFG - T0 DPLL Holdover Frequency Configuration 1 Address: 5DH Type: Read / Write Default Value: 00000000 7 T0_HOLDOVER _FREQ7 Bit 7-0 6 T0_HOLDOVER _FREQ6 Name 5 T0_HOLDOVER _FREQ5 4 T0_HOLDOVE R_FREQ4 3 T0_HOLDOVE R_FREQ3 2 T0_HOLDOVE R_FREQ2 1 T0_HOLDOVE R_FREQ1 0 T0_HOLDOVE R_FREQ0 Description T0_HOLDOVER_FREQ[7:0] Refer to the description of the T0_HOLDOVER_FREQ[23:16] bits (b7~0, 5FH). Programming Information 129 June 19, 2006 IDT82V3280 WAN PLL T0_HOLDOVER_FREQ[15:8]_CNFG - T0 DPLL Holdover Frequency Configuration 2 Address: 5EH Type: Read / Write Default Value: 00000000 7 T0_HOLDOVER _FREQ15 Bit 7-0 6 T0_HOLDOVER _FREQ14 Name 5 T0_HOLDOVER _FREQ13 4 T0_HOLDOVE R_FREQ12 3 T0_HOLDOVE R_FREQ11 2 T0_HOLDOVE R_FREQ10 Description 1 T0_HOLDOVE R_FREQ9 0 T0_HOLDOVE R_FREQ8 T0_HOLDOVER_FREQ[15:8] Refer to the description of the T0_HOLDOVER_FREQ[23:16] bits (b7~0, 5FH). T0_HOLDOVER_FREQ[23:16]_CNFG - T0 DPLL Holdover Frequency Configuration 3 Address: 5FH Type: Read / Write Default Value: 00000000 7 T0_HOLDOVER _FREQ23 Bit 7-0 6 T0_HOLDOVER _FREQ22 Name 5 T0_HOLDOVER _FREQ21 4 T0_HOLDOVE R_FREQ20 3 T0_HOLDOVE R_FREQ19 2 T0_HOLDOVE R_FREQ18 Description 1 T0_HOLDOVE R_FREQ17 0 T0_HOLDOVE R_FREQ16 The T0_HOLDOVER_FREQ[23:0] bits represent a 2's complement signed integer. In T0 DPLL Holdover mode, the value written to these bits multiplied by 0.000011 is the frequency offset set manuT0_HOLDOVER_FREQ[23:16] ally; the value read from these bits multiplied by 0.000011 is the frequency offset automatically slow or fast averaged or manually set, as determined by the READ_AVG bit (b4, 5CH) and the FAST_AVG bit (b5, 5CH). Programming Information 130 June 19, 2006 IDT82V3280 WAN PLL T4_DPLL_APLL_PATH_CNFG - T4 DPLL & APLL Path Configuration Address: 60H Type: Read / Write Default Value: 01000X0X 7 T4_APLL_PATH 3 Bit 6 T4_APLL_PA TH2 Name 5 T4_APLL_PA TH1 4 T4_APLL_PA TH0 3 T4_GSM_GPS_16 E1_16T1_SEL1 2 T4_GSM_GPS_16 E1_16T1_SEL0 Description 1 T4_12E1_24T1_ E3_T3_SEL1 0 T4_12E1_24T1_ E3_T3_SEL0 7-4 3-2 1-0 These bits select an input to the T4 APLL. 0000: The output of T0 DPLL 77.76 MHz path. 0001: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0010: The output of T0 DPLL 16E1/16T1 path. 0011: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. T4_APLL_PATH[3:0] 0100: The output of T4 DPLL 77.76 MHz path. (default) 0101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T4 DPLL 16E1/16T1 path. 0111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. 1XXX: Reserved. These bits select an output clock from the T4 DPLL GSM/GPS/16E1/16T1 path. 00: 16E1. 01: 16T1. T4_GSM_GPS_16E1_16T1_SEL[1:0] 10: GSM. 11: GPS. The default value of the T0_GSM_GPS_16E1_16T1_SEL0 bit is determined by the SONET/SDH pin during reset. These bits select an output clock from the T4 DPLL 12E1/24T1/E3/T3 path. 00: 12E1. 01: 24T1. T4_12E1_24T1_E3_T3_SEL[1:0] 10: E3. 11: T3. The default value of the T4_12E1_24T1_E3_T3_SEL0 bit is determined by the SONET/SDH pin during reset. Programming Information 131 June 19, 2006 IDT82V3280 WAN PLL T4_DPLL_LOCKED_BW_DAMPING_CNFG - T4 DPLL Locked Bandwidth & Damping Factor Configuration Address: 61H Type: Read / Write Default Value: 011XXX00 7 T4_DPLL_LOCK ED_DAMPING2 Bit 6 T4_DPLL_LOCK ED_DAMPING1 Name 5 T4_DPLL_LOCK ED_DAMPING0 4 3 2 Description 1 T4_DPLL_LOC KED_BW1 0 T4_DPLL_LOC KED_BW0 7-5 4-2 1-0 These bits set the locked damping factor for T4 DPLL. 000: Reserved. 001: 1.2. 010: 2.5. T4_DPLL_LOCKED_DAMPING[2:0] 011: 5. (default) 100: 10. 101: 20. 110, 111: Reserved. Reserved. These bits set the locked bandwidth for T4 DPLL. 00: 18 Hz. (default) T4_DPLL_LOCKED_BW[1:0] 01: 35 Hz. 10: 70 Hz. 11: 560 Hz. CURRENT_DPLL_FREQ[7:0]_STS - DPLL Current Frequency Status 1 * Address: 62H Type: Read Default Value: 00000000 7 CURRENT_DP LL_FREQ7 Bit 7-0 6 CURRENT_DP LL_FREQ6 Name 5 CURRENT_DP LL_FREQ5 4 CURRENT_DP LL_FREQ4 3 CURRENT_DP LL_FREQ3 2 CURRENT_DP LL_FREQ2 Description 1 CURRENT_DP LL_FREQ1 0 CURRENT_DP LL_FREQ0 CURRENT_DPLL_FREQ[7:0] Refer to the description of the CURRENT_DPLL_FREQ[23:16] bits (b7~0, 64H). CURRENT_DPLL_FREQ[15:8]_STS - DPLL Current Frequency Status 2 * Address: 63H Type: Read Default Value: 00000000 7 CURRENT_DP LL_FREQ15 Bit 7-0 6 CURRENT_DP LL_FREQ14 Name 5 CURRENT_DP LL_FREQ13 4 CURRENT_DP LL_FREQ12 3 CURRENT_DP LL_FREQ11 2 CURRENT_DP LL_FREQ10 Description 1 CURRENT_DP LL_FREQ9 0 CURRENT_DP LL_FREQ8 CURRENT_DPLL_FREQ[15:8] Refer to the description of the CURRENT_DPLL_FREQ[23:16] bits (b7~0, 64H). Programming Information 132 June 19, 2006 IDT82V3280 WAN PLL CURRENT_DPLL_FREQ[23:16]_STS - DPLL Current Frequency Status 3 * Address: 64H Type: Read Default Value: 00000000 7 CURRENT_DP LL_FREQ23 Bit 7-0 6 CURRENT_DP LL_FREQ22 Name 5 CURRENT_DP LL_FREQ21 4 CURRENT_DP LL_FREQ20 3 CURRENT_DP LL_FREQ19 2 CURRENT_DP LL_FREQ18 Description 1 CURRENT_DP LL_FREQ17 0 CURRENT_DP LL_FREQ16 The CURRENT_DPLL_FREQ[23:0] bits represent a 2's complement signed integer. If the value in these bits is mulCURRENT_DPLL_FREQ[23:16] tiplied by 0.000011, the current frequency offset of the T0/T4 DPLL output in ppm with respect to the master clock will be gotten. DPLL_FREQ_SOFT_LIMIT_CNFG - DPLL Soft Limit Configuration Address: 65H Type: Read / Write Default Value: 10001100 7 FREQ_LIMT_P H_LOS Bit 7 6 DPLL_FREQ_S OFT_LIMT6 Name FREQ_LIMT_PH_LOS 5 DPLL_FREQ_S OFT_LIMT5 4 DPLL_FREQ_S OFT_LIMT4 3 DPLL_FREQ_S OFT_LIMT3 2 DPLL_FREQ_S OFT_LIMT2 1 DPLL_FREQ_S OFT_LIMT1 0 DPLL_FREQ_S OFT_LIMT0 Description 6-0 This bit determines whether the T0/T4 DPLL in hard alarm status will result in it unlocked. 0: Disabled. 1: Enabled. (default) These bits represent an unsigned integer. If the value is multiplied by 0.724, the DPLL soft limit for T0 and T4 paths in DPLL_FREQ_SOFT_LIMT[6:0] ppm will be gotten. The DPLL soft limit is symmetrical about zero. DPLL_FREQ_HARD_LIMIT[7:0]_CNFG - DPLL Hard Limit Configuration 1 Address: 66H Type: Read / Write Default Value: 10101011 7 DPLL_FREQ_H ARD_LIMT7 Bit 7-0 6 DPLL_FREQ_H ARD_LIMT6 Name 5 DPLL_FREQ_H ARD_LIMT5 4 DPLL_FREQ_H ARD_LIMT4 3 DPLL_FREQ_H ARD_LIMT3 2 DPLL_FREQ_H ARD_LIMT2 Description 1 DPLL_FREQ_H ARD_LIMT1 0 DPLL_FREQ_H ARD_LIMT0 DPLL_FREQ_HARD_LIMT[7:0] Refer to the description of the DPLL_FREQ_HARD_LIMT[15:8] bits (b7~0, 67H). Programming Information 133 June 19, 2006 IDT82V3280 WAN PLL DPLL_FREQ_HARD_LIMIT[15:8]_CNFG - DPLL Hard Limit Configuration 2 Address: 67H Type: Read / Write Default Value: 00011001 7 DPLL_FREQ_H ARD_LIMT15 Bit 7-0 6 DPLL_FREQ_H ARD_LIMT14 Name 5 DPLL_FREQ_H ARD_LIMT13 4 DPLL_FREQ_H ARD_LIMT12 3 DPLL_FREQ_H ARD_LIMT11 2 DPLL_FREQ_H ARD_LIMT10 Description 1 DPLL_FREQ_H ARD_LIMT9 0 DPLL_FREQ_H ARD_LIMT8 The DPLL_FREQ_HARD_LIMT[15:0] bits represent an unsigned integer. If the value is multiplied by 0.0014, the DPLL_FREQ_HARD_LIMT[15:8] DPLL hard limit for T0 and T4 paths in ppm will be gotten. The DPLL hard limit is symmetrical about zero. CURRENT_DPLL_PHASE[7:0]_STS - DPLL Current Phase Status 1 * Address: 68H Type: Read Default Value: 00000000 7 CURRENT_PH _DATA7 Bit 7-0 6 CURRENT_PH _DATA6 Name 5 CURRENT_PH _DATA5 4 CURRENT_PH _DATA4 3 CURRENT_PH _DATA3 2 CURRENT_PH _DATA2 Description 1 CURRENT_PH _DATA1 0 CURRENT_PH _DATA0 CURRENT_PH_DATA[7:0] Refer to the description of the CURRENT_PH_DATA[15:8] bits (b7~0, 69H). CURRENT_DPLL_PHASE[15:8]_STS - DPLL Current Phase Status 2 * Address: 69H Type: Read Default Value: 00000000 7 CURRENT_PH _DATA15 Bit 7-0 6 CURRENT_PH _DATA14 Name 5 CURRENT_PH _DATA13 4 CURRENT_PH _DATA12 3 CURRENT_PH _DATA11 2 CURRENT_PH _DATA10 Description 1 CURRENT_PH _DATA9 0 CURRENT_PH _DATA8 The CURRENT_PH_DATA[15:0] bits represent a 2's complement signed integer. If the value is multiplied by 0.61, the CURRENT_PH_DATA[15:8] averaged phase error of the T0/T4 DPLL feedback with respect to the selected input clock in ns will be gotten. Programming Information 134 June 19, 2006 IDT82V3280 WAN PLL T0_T4_APLL_BW_CNFG - T0 / T4 APLL Bandwidth Configuration Address: 6AH Type: Read / Write Default Value: XX01XX01 7 Bit 7-6 Name Reserved. These bits set the bandwidth for T0 APLL. 00: 100 kHz. T0_APLL_BW[1:0] 01: 500 kHz. (default) 10: 1 MHz. 11: 2 MHz. Reserved. These bits set the bandwidth for T4 APLL. 00: 100 kHz. T4_APLL_BW[1:0] 01: 500 kHz. (default) 10: 1 MHz. 11: 2 MHz. 6 5 T0_APLL_BW1 4 T0_APLL_BW0 3 Description 2 1 T4_APLL_BW1 0 T4_APLL_BW0 5-4 3-2 1-0 Programming Information 135 June 19, 2006 IDT82V3280 WAN PLL 7.2.8 OUTPUT CONFIGURATION REGISTERS OUT1_FREQ_CNFG - Output Clock 1 Frequency Configuration Address: 6BH Type: Read / Write Default Value: 00001011 7 OUT1_PATH_S EL3 Bit 6 OUT1_PATH_S EL2 Name 5 OUT1_PATH_S EL1 4 OUT1_PATH_S EL0 3 OUT1_DIVIDER 3 2 OUT1_DIVIDER 2 1 OUT1_DIVIDER 1 0 OUT1_DIVIDER 0 Description 7-4 3-0 These bits select an input to OUT1. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. OUT1_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT1. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output OUT1_DIVIDER[3:0] (selected by the OUT1_PATH_SEL[3:0] bits (b7~4, 6BH)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. Programming Information 136 June 19, 2006 IDT82V3280 WAN PLL OUT2_FREQ_CNFG - Output Clock 2 Frequency Configuration Address: 6CH Type: Read / Write Default Value: 00000110 7 OUT2_PATH_S EL3 Bit 6 OUT2_PATH_S EL2 Name 5 OUT2_PATH_S EL1 4 OUT2_PATH_S EL0 3 OUT2_DIVIDER 3 2 OUT2_DIVIDER 2 1 OUT2_DIVIDER 1 0 OUT2_DIVIDER 0 Description These bits select an input to OUT2. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT2. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output (selected by the OUT2_PATH_SEL[3:0] bits (b7~4, 6CH)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. 7-4 OUT2_PATH_SEL[3:0] 3-0 OUT2_DIVIDER[3:0] Programming Information 137 June 19, 2006 IDT82V3280 WAN PLL OUT3_FREQ_CNFG - Output Clock 3 Frequency Configuration Address: 6DH Type: Read / Write Default Value: 00001000 7 OUT3_PATH_S EL3 Bit 6 OUT3_PATH_S EL2 Name 5 OUT3_PATH_S EL1 4 OUT3_PATH_S EL0 3 OUT3_DIVIDER 3 2 OUT3_DIVIDER 2 1 OUT3_DIVIDER 1 0 OUT3_DIVIDER 0 Description 7-4 3-0 These bits select an input to OUT3. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. OUT3_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT3. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output OUT3_DIVIDER[3:0] (selected by the OUT3_PATH_SEL[3:0] bits (b7~4, 6DH)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. Programming Information 138 June 19, 2006 IDT82V3280 WAN PLL OUT4_FREQ_CNFG - Output Clock 4 Frequency Configuration Address: 6EH Type: Read / Write Default Value: 00000110 7 OUT4_PATH_S EL3 Bit 6 OUT4_PATH_S EL2 Name 5 OUT4_PATH_S EL1 4 OUT4_PATH_S EL0 3 OUT4_DIVIDER 3 2 OUT4_DIVIDER 2 1 OUT4_DIVIDER 1 0 OUT4_DIVIDER 0 Description 7-4 3-0 These bits select an input to OUT4. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. OUT4_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT4. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output OUT4_DIVIDER[3:0] (selected by the OUT4_PATH_SEL[3:0] bits (b7~4, 6EH)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. Programming Information 139 June 19, 2006 IDT82V3280 WAN PLL OUT5_FREQ_CNFG - Output Clock 5 Frequency Configuration Address: 6FH Type: Read / Write Default Value: 00000100 7 OUT5_PATH_S EL3 Bit 6 OUT5_PATH_S EL2 Name 5 OUT5_PATH_S EL1 4 OUT5_PATH_S EL0 3 OUT5_DIVIDER 3 2 OUT5_DIVIDER 2 1 OUT5_DIVIDER 1 0 OUT5_DIVIDER 0 Description 7-4 3-0 These bits select an input to OUT5. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. OUT5_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT5. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output OUT5_DIVIDER[3:0] (selected by the OUT5_PATH_SEL[3:0] bits (b7~4, 6FH)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. Programming Information 140 June 19, 2006 IDT82V3280 WAN PLL OUT6_FREQ_CNFG - Output Clock 6 Frequency Configuration Address:70H Type: Read / Write Default Value: 00000110 7 OUT6_PATH_S EL3 Bit 6 OUT6_PATH_S EL2 Name 5 OUT6_PATH_S EL1 4 OUT6_PATH_S EL0 3 OUT6_DIVIDER 3 2 OUT6_DIVIDER 2 1 OUT6_DIVIDER 1 0 OUT6_DIVIDER 0 Description 7-4 3-0 These bits select an input to OUT6. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. OUT6_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT6. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output OUT6_DIVIDER[3:0] (selected by the OUT6_PATH_SEL[3:0] bits (b7~4, 70H)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. Programming Information 141 June 19, 2006 IDT82V3280 WAN PLL OUT7_FREQ_CNFG - Output Clock 7 Frequency Configuration Address:71H Type: Read / Write Default Value: 00001000 7 OUT7_PATH_S EL3 Bit 6 OUT7_PATH_S EL2 Name 5 OUT7_PATH_S EL1 4 OUT7_PATH_S EL0 3 OUT7_DIVIDER 3 2 OUT7_DIVIDER 2 1 OUT7_DIVIDER 1 0 OUT7_DIVIDER 0 Description 7-4 3-0 These bits select an input to OUT7. 0000 ~ 0011: The output of T0 APLL. (default: 0000) 0100: The output of T0 DPLL 77.76 MHz path. 0101: The output of T0 DPLL 12E1/24T1/E3/T3 path. 0110: The output of T0 DPLL 16E1/16T1 path. OUT7_PATH_SEL[3:0] 0111: The output of T0 DPLL GSM/OBSAI/16E1/16T1 path. 1000 ~ 1011: The output of T4 APLL. 1100: The output of T4 DPLL 77.76 MHz path. 1101: The output of T4 DPLL 12E1/24T1/E3/T3 path. 1110: The output of T4 DPLL 16E1/16T1 path. 1111: The output of T4 DPLL GSM/GPS/16E1/16T1 path. These bits select a division factor of the divider for OUT7. The output frequency is determined by the division factor and the signal derived from T0/T4 DPLL or T0/T4 APLL output OUT7_DIVIDER[3:0] (selected by the OUT7_PATH_SEL[3:0] bits (b7~4, 71H)). If the signal is derived from one of the T0/T4 DPLL outputs, please refer to Table 24 for the division factor selection. If the signal is derived from the T0/T4 APLL output, please refer to Table 25 for the division factor selection. Programming Information 142 June 19, 2006 IDT82V3280 WAN PLL OUT8_FREQ_CNFG - Output Clock 8 Frequency Configuration & Output Clock 6, 7 & 9 Invert Configuration Address:72H Type: Read / Write Default Value: 01000000 7 OUT8_PATH_S EL Bit 7 6 6 OUT8_EN Name 5 T4_INPUT_FAI L 4 AMI_OUT_DUT Y 3 400HZ_SEL 2 OUT9_INV 1 OUT7_INV 0 OUT6_INV Description These bits select an input to OUT8. OUT8_PATH_SEL 0: The output of T4 DPLL 77.76 MHz path. (default) 1: The output of T0 DPLL 77.76 MHz path. OUT8_EN Refer to the description of the T4_INPUT_FAIL bit (b5, 72H). This bit, together with the OUT8_EN bit (b6, 72H), determines whether a clock is enabled to be output on OUT8. OUT8_EN T4_INPUT_FAIL Output on OUT8 Output is disabled (output low). Output is enabled. (default) Output is enabled when the T4 selected input clock does not fail. Output is disabled (output low) when the T4 selected input clock fails. 5 T4_INPUT_FAIL 0 1 don't-care 0 1 4 3 2 1 0 This bit determines the duty cycle of the output on OUT8. AMI_OUT_DUTY 0: 50:50. (default) 1: 5:8. This bit determines the frequency of the output on OUT8. 400HZ_SEL 0: 64 kHz + 8 kHz. (default) 1: 64 kHz + 8 kHz + 0.4 kHz. This bit determines whether the output on OUT9 is inverted. OUT9_INV 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on OUT7 is inverted. OUT7_INV 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on OUT6 is inverted. OUT6_INV 0: Not inverted. (default) 1: Inverted. Programming Information 143 June 19, 2006 IDT82V3280 WAN PLL OUT9_FREQ_CNFG - Output Clock 9 Frequency Configuration & Output Clock 1 ~ 5 Invert Configuration Address:73H Type: Read / Write Default Value: 01000000 7 OUT9_PATH_S EL Bit 7 6 6 OUT9_EN Name 5 T4_INPUT_FAI L 4 OUT5_INV 3 OUT4_INV 2 OUT3_INV 1 OUT2_INV 0 OUT1_INV Description These bits select an input to OUT9. OUT9_PATH_SEL 0: The output of T4 DPLL 16E1/16T1 path. (default) 1: The output of T0 DPLL 16E1/16T1 path. OUT9_EN Refer to the description of the T4_INPUT_FAIL bit (b5, 73H). This bit, together with the OUT9_EN bit (b6, 73H), determines whether clock is enabled to output on OUT9. OUT9_EN 0 T4_INPUT_FAIL don't-care 0 1 Output on OUT9 Output is disabled (output low). Output is enabled. (default) Output is enabled when the T4 selected input clock does not fail. Output is disabled (output low) when the T4 selected input clock fails. (Whether the T4 selected input clock is switched or not, as long as the T4 selected input clock does not change to be invalid, the T4 selected input clock does not fail). 5 T4_INPUT_FAIL 1 4 OUT5_INV 3 OUT4_INV 2 OUT3_INV 1 OUT2_INV 0 OUT1_INV This bit determines whether the output on OUT5 is inverted. 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on OUT4 is inverted. 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on OUT3 is inverted. 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on OUT2 is inverted. 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on OUT1 is inverted. 0: Not inverted. (default) 1: Inverted. Programming Information 144 June 19, 2006 IDT82V3280 WAN PLL FR_MFR_SYNC_CNFG - Frame Sync & Multiframe Sync Output Configuration Address:74H Type: Read / Write Default Value: 01100000 7 IN_2K_4K_8K_I NV Bit 7 6 8K_EN Name 5 2K_EN 4 2K_8K_PUL_P OSITION 3 8K_INV 2 8K_PUL Description 1 2K_INV 0 2K_PUL 6 5 4 3 2 1 0 This bit determines whether the input clock is inverted before locked by the T0/T4 DPLL when the input clock is 2 kHz, 4 kHz or 8 kHz. IN_2K_4K_8K_INV 0: Not inverted. (default) 1: Inverted. This bit determines whether an 8 kHz signal is enabled to be output on FRSYNC_8K. 8K_EN 0: Disabled. FRSYNC_8K outputs low. 1: Enabled. (default) This bit determines whether a 2 kHz signal is enabled to be output on MFRSYNC_2K. 2K_EN 0: Disabled. MFRSYNC_2K outputs low. 1: Enabled. (default) This bit is valid only when FRSYNC_8K and/or MFRSYNC_2K output pulse; i.e., when one of the 8K_PUL bit (b2, 74H) and the 2K_PUL bit (b0, 74H) is `1' or when the 8K_PUL bit (b2, 74H) and the 2K_PUL bit (b0, 74H) are both `1'. It deter2K_8K_PUL_POSITION mines the pulse position referring to the standard 50:50 duty cycle. 0: Pulsed on the falling edge of the standard 50:50 duty cycle position. (default) 1: Pulsed on the rising edge of the standard 50:50 duty cycle position. This bit determines whether the output on FRSYNC_8K is inverted. 8K_INV 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on FRSYNC_8K is 50:50 duty cycle or pulsed. 8K_PUL 0: 50:50 duty cycle. (default) 1: Pulsed. The pulse width is defined by the period of the output on OUT3. This bit determines whether the output on MFRSYNC_2K is inverted. 2K_INV 0: Not inverted. (default) 1: Inverted. This bit determines whether the output on MFRSYNC_2K is 50:50 duty cycle or pulsed. 2K_PUL 0: 50:50 duty cycle. (default) 1: Pulsed. The pulse width is defined by the period of the output on OUT3. Programming Information 145 June 19, 2006 IDT82V3280 WAN PLL 7.2.9 PBO & PHASE OFFSET CONTROL REGISTERS PHASE_MON_PBO_CNFG - Phase Transient Monitor & PBO Configuration Address:78H Type: Read / Write Default Value: 0X000110 7 IN_NOISE_WIN DOW Bit 7 6 5 6 Name 5 PH_MON_EN 4 PH_MON_PBO _EN 3 PH_TR_MON_L IMT3 2 PH_TR_MON_L IMT2 1 PH_TR_MON_L IMT1 0 PH_TR_MON_L IMT0 Description 4 3-0 This bit determines whether the input clock whose edge respect to the reference clock is outside 5% is enabled to be selected for T0/T4 DPLL. IN_NOISE_WINDOW 0: Disabled. (default) 1: Enabled. Reserved. This bit is valid only when the PH_MON_PBO_EN bit (b4, 78H) is `1'. It determines whether the Phase Transient Monitor is enabled to monitor the phase-time changes on the T0 selected input clock. PH_MON_EN 0: Disabled. (default) 1: Enabled. This bit determines whether a PBO event is triggered when the phase-time changes on the T0 selected input clock are greater than a programmable limit over an interval of less than 0.1 seconds with the PH_MON_EN bit being `1'. The limit PH_MON_PBO_EN is programmed by the PH_TR_MON_LIMT[3:0] bits (b3~0, 78H). 0: Disabled. (default) 1: Enabled. These bits represent an unsigned integer. The Phase Transient Monitor limit in ns can be calculated as follows: PH_TR_MON_LIMT[3:0] Limit (ns) = (PH_TR_MON_LIMT[3:0] + 7) X 156. PHASE_OFFSET[7:0]_CNFG - Phase Offset Configuration 1 Address:7AH Type: Read / Write Default Value: 00000000 7 PH_OFFSET7 Bit 7-0 6 PH_OFFSET6 Name 5 PH_OFFSET5 4 PH_OFFSET4 3 PH_OFFSET3 2 PH_OFFSET2 1 PH_OFFSET1 0 PH_OFFSET0 Description PH_OFFSET[7:0] Refer to the description of the PH_OFFSET[9:8] bits (b1~0, 7BH). Programming Information 146 June 19, 2006 IDT82V3280 WAN PLL PHASE_OFFSET[9:8]_CNFG - Phase Offset Configuration 2 Address:7BH Type: Read / Write Default Value: 0XXXXX00 7 PH_OFFSET_E N Bit Name 6 5 4 3 2 1 PH_OFFSET9 0 PH_OFFSET8 Description 7 6-2 1-0 This bit determines whether the input-to-output phase offset is enabled. If the device is configured as the Master, the input-to-output phase offset: PH_OFFSET_EN 0: Disabled. (default) 1: Enabled. If the device is configured as the Slave, the input-to-output phase offset is always enabled. Reserved. These bits represent a 2's complement signed integer. If the value is multiplied by 0.61, the input-to-output phase offset in ns PH_OFFSET[9:8] to adjust will be gotten. Programming Information 147 June 19, 2006 IDT82V3280 WAN PLL 7.2.10 SYNCHRONIZATION CONFIGURATION REGISTERS SYNC_MONITOR_CNFG - Sync Monitor Configuration Address:7CH Type: Read / Write Default Value: X0101011 7 Bit 7 6 SYNC_MON_LIMT2 Name Reserved. These bits set the limit for the external sync alarm. 000: 1 UI. 001: 2 UI. 010: 3 UI. (default) SYNC_MON_LIMT[2:0] 011: 4 UI. 100: 5 UI. 101: 6 UI. 110: 7 UI. 111: 8 UI. These bits must be set to `1011'. 5 SYNC_MON_LIMT1 4 SYNC_MON_LIMT0 3 Description 2 1 0 - 6-4 3-0 SYNC_PHASE_CNFG - Sync Phase Configuration Address:7DH Type: Read / Write Default Value: XXXXXX00 7 Bit 7-2 Name 6 5 4 3 Description Reserved. These bits set the sampling of EX_SYNC1 when EX_SYNC1 is enabled to synchronize the frame sync output signal. Nominally, the falling edge of EX_SYNC1 is aligned with the rising edge of the T0 selected input clock. 00: On target. (default) 01: 0.5 UI early. 10: 1 UI late. 11: 0.5 UI late. 2 1 SYNC_PH11 0 SYNC_PH10 1-0 SYNC_PH1[1:0] Programming Information 148 June 19, 2006 IDT82V3280 WAN PLL 8 THERMAL MANAGEMENT The junction temperature Tj can be calculated as follows: Tj = TA + P X JA = 85C + 1.9W X 18.5C/W = 120.2C The device operates over the industry temperature range -40C ~ +85C. To ensure the functionality and reliability of the device, the maximum junction temperature Tjmax should not exceed 125C. In some applications, the device will consume more power and a thermal solution should be provided to ensure the junction temperature Tj does not exceed the Tjmax. The junction temperature of 120.2C is below the maximum junction temperature of 125C so no extra heat enhancement is required. In some operation environments, the calculated junction temperature might exceed the maximum junction temperature of 125C and an external thermal solution such as a heatsink is required. 8.1 JUNCTION TEMPERATURE 8.3 HEATSINK EVALUATION Junction temperature Tj is the temperature of package typically at the geographical center of the chip where the device's electrical circuits are. It can be calculated as follows: Equation 1: Tj = TA + P X JA A heatsink is expanding the surface area of the device to which it is attached. JA is now a combination of device case and heat-sink thermal resistance, as the heat flowing from the die junction to ambient goes through the package and the heatsink. JA can be calculated as follows: Equation 2: JA = JC + HA Where: JA = Junction-to-Ambient Thermal Resistance of the Package Tj = Junction Temperature TA = Ambient Temperature P = Device Power Consumption Where: JC = Junction-to-Case (Heatsink) Thermal Resistance HA = Heatsink-to-Ambient Thermal Resistance In order to calculate junction temperature, an appropriate JA must be used. The JA is shown in Table 44: Power consumption is the core power excluding the power dissipated in the loads. Table 43 provides power consumption in special environments. Table 43: Power Consumption and Maximum Junction Temperature Package TQFP/PN100 TQFP/DQ100 Power Consumption (W) 1.9 1.9 Operating Voltage (V) 3.6 3.6 Maximum TA (C) Junction Temperature (C) 85 85 125 125 HA determines which heatsink can be selected to ensure the junction temperature does not exceed the maximum junction temperature. According to Equation 1 and 2, the heatsink-to-ambient thermal resistance HA can be calculated as follows: Equation 3: HA = (Tj - TA) / P - JC Assume: Tj = 125C (Tjmax) TA = 85C P = 1.9W JC = 10.8C/W (TQFP/DQ100) The heatsink-to-ambient thermal resistance HA can be calculated as follows: HA = (125C - 85C ) / 1.9W - 10.8C/W = 10.3C/W 8.2 EXAMPLE OF JUNCTION TEMPERATURE CALCULATION TA = 85C Assume: JA = 18.5C/W (TQFP/DQ100 Soldered & when airfow rate is 0 m/s) P = 1.9W That is, if a heatsink whose heatsink-to-ambient thermal resistance HA is below or equal to 10.3C/W is used in such operation environment, the junction temperature will not exceed the maximum junction temperature. Table 44: Thermal Data Package TQFP/PN100 TQFP/DQ100 TQPF/DQ100 Pin Count 100 100 100 Thermal Pad No Yes/Exposed Yes/Soldered JC (C/W) JB (C/W) JA (C/W) Air Flow in m/s 0 39.3 27.2 18.5 1 36.2 24.7 15.4 2 34.3 23.3 13.9 3 33.5 22.4 13.1 4 32.9 21.9 12.6 5 32.6 21.5 12.2 11.0 10.8 10.8 34.2 23.7 3.0 Thermal Management 149 June 19, 2006 IDT82V3280 WAN PLL 9 9.1 ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATING Table 45: Absolute Maximum Rating Symbol VDD VIN VOUT TA TSTOR Parameter Supply Voltage VDD Input Voltage (non-supply pins) Output Voltage (non-supply pins) Ambient Operating Temperature Range Storage Temperature -40 -50 Min -0.5 Max 3.6 5.5 5.5 +85 +150 Unit V V V C C 9.2 RECOMMENDED OPERATION CONDITIONS Table 46: Recommended Operation Conditions Symbol VDD TA IDD PTOT Parameter Power Supply (DC voltage) VDD Ambient Temperature Range Supply Current Total Power Dissipation Min 3.0 -40 455 1.5 Typ 3.3 Max 3.6 +85 528 1.9 Unit V C mA W Electrical Specifications 150 June 19, 2006 IDT82V3280 WAN PLL 9.3 9.3.1 9.3.1.1 I/O SPECIFICATIONS AMI INPUT / OUTPUT PORT Structure Violation Violation Violation 8 kHz (125 s) 8 kHz (125 s) 8 kHz (125 s) Figure 27. 64 kHz + 8 kHz Signal Structure Violation Violation Violation Violation 8 kHz (125 s) 8 kHz (125 s) 8 kHz (125 s) 0.4 kHz (2.5 ms) 8 kHz (125 s) Figure 28. 64 kHz + 8 kHz + 0.4 kHz Signal Structure 9.3.1.2 I/O Level 15.6 s 7.8 s + 1.0 VIH 0 VIM 1V 470 nF IN1 OUT8_POS 0V + VDD 15.6 s 7.8 s 2 Vp-p - 1.0 VIL 1V IN2 470 nF OUT8_NEG 470 nF + VDD 0V 15.6 s 7.8 s Signal structure of 64 kHz / 8 kHz central clock interface after suitable transformer Figure 29. 64 kHz + 8 kHz / 64 kHz + 8 kHz + 0.4 kHz Signal Input Level Figure 30. 64 kHz + 8 kHz / 64 kHz + 8 kHz + 0.4 kHz Signal Output Level Electrical Specifications 151 June 19, 2006 IDT82V3280 WAN PLL AMI input 470 nF IN1 OUT8_POS 470 nF Turns ratio 3:1 Rload AMI output 2 nF GND AMI input 470 nF IN2 OUT8_NEG For a transformer with a turns ratio of 1:1, a 3:1 ratio potential divider Rload must be used to achieve the required 1 V pk-pk voltage level for the positive and negative pulses. Figure 31. AMI Input / Output Port Line Termination (Recommended) Table 47: AMI Input / Output Port Electrical Characteristics Parameter tPW tR/F VIH VIM VIL IOUT VOH VOL RTEST VMARK VSPACE Description Input Pulse Width Input Pulse Rise/Fall Time Input Voltage High Input Voltage Middle Input Voltage Low Output Current Drive Output Voltage High, Output Current = 20 mA Output Voltage Low, Output Current = 20 mA Nominal Test Load Impedance `Mark' Amplitude after Transformer "Space" Amplitude after Transformer 0.9 -0.1 110 1.0 0 1.1 0.1 VDD - 0.16 0.16 2.5 1.5 0 1.65 Min 1.56 Typ 7.8 Max 14.04 5 VDD + 0.3 1.8 1.4 20 Unit S S V V V mA V V V V Electrical Specifications 152 June 19, 2006 IDT82V3280 WAN PLL 9.3.1.3 Over-Voltage Protection The device may require over-voltage protection on AMI input ports according to ITU Recommendation K.41. 9.3.2 CMOS INPUT / OUTPUT PORT From Table 48 to Table 51, VDD is 3.3 V. Table 48: CMOS Input Port Electrical Characteristics Parameter VIH VIL IIN VIN Description Input Voltage High Input Voltage Low Input Current Input Voltage -0.5 Min 0.7VDD 0.2VDD 10 5.5 Typ Max Unit V V A Test Condition V Table 49: CMOS Input Port with Internal Pull-Up Resistor Electrical Characteristics Parameter VIH VIL PU IIN VIN Description Input Voltage High Input Voltage Low Pull-Up Resistor Input Current Input Voltage -0.5 10 Min 0.7VDD 0.2VDD 80 250 5.5 Typ Max Unit V V K A Test Condition V Table 50: CMOS Input Port with Internal Pull-Down Resistor Electrical Characteristics Parameter VIH VIL PD Description Input Voltage High Input Voltage Low Pull-Down Resistor 10 5 100 Min 0.7VDD 0.2VDD 80 40 300 350 700 40 5.5 Typ Max Unit V V K other CMOS input port with internal pull-down resistor TRST and TCK pin A[6:0], AD[7:0] pins other CMOS input port with internal pull-down resistor TRST and TCK pin A[6:0], AD[7:0] pins Test Condition IIN VIN Input Current Input Voltage -0.5 A V Table 51: CMOS Output Port Electrical Characteristics Application Pin Parameter VOH Output Clock VOL tR tF VOH Other Output VOL tR tF Description Output Voltage High Output Voltage Low Rise time Fall time Output Voltage High Output Voltage Low Rise Time Fall Time 2.5 0 Min 2.4 0 3 3 Typ Max VDD 0.4 4 4 VDD 0.4 10 10 Unit V V ns ns V V ns ns Test Condition IOH = 8 mA IOL = 8 mA 15 pF 15 pF IOH = 4 mA IOL= 4 mA 50 pF 50 pF Electrical Specifications 153 June 19, 2006 IDT82V3280 WAN PLL 9.3.3 9.3.3.1 PECL / LVDS INPUT / OUTPUT PORT PECL Input / Output Port VDD (+ 3.3 V) 50 (transmission line) 2 kHz to 667 MHz 130 IN5_POS 82 GND VDD (+ 3.3 V) 130 IN5_NEG 82 GND VDD (+ 3.3 V) 50 (transmission line) 130 IN6_POS 82 2 kHz to 667 MHz GND VDD (+ 3.3 V) 130 IN6_NEG 82 GND 130 82 VDD (+ 3.3 V) GND 50 (transmission line) 2 kHz OUT6_POS to 667 MHz OUT6_NEG 50 (transmission line) VDD (+ 3.3 V) GND 130 82 130 82 VDD (+ 3.3 V) GND 50 (transmission line) 2 kHz OUT7_POS to 667 MHz OUT7_NEG 50 (transmission line) VDD (+ 3.3 V) GND 130 82 50 (transmission line) Figure 33. Recommended PECL Output Port Line Termination 50 (transmission line) Figure 32. Recommended PECL Input Port Line Termination Electrical Specifications 154 June 19, 2006 IDT82V3280 WAN PLL Table 52: PECL Input / Output Port Electrical Characteristics Parameter VIL VIH VID VIL_S VIH_S IIH IIL VOL VOH VOD tRISE tFALL tSKEW Description Input Low Voltage, Differential Inputs Input Differential Voltage Input Low Voltage, Single-ended Input 2 Input High Voltage, Single-ended Input 2 Input High Current, Input Differential Voltage VID = 1.4 V Input Low Current, Input Differential Voltage VID = 1.4 V Output Voltage Low 3 Output Voltage High 3 Output Differential Voltage3 Output Rise time (20% to 80%) Output Fall time (20% to 80%) Output Differential Skew 1 Min VDD - 2.5 VDD - 2.4 0.1 VDD - 2.4 VDD - 1.3 -10 -10 VDD - 2.1 VDD - 1.25 580 200 200 Typ Max VDD - 0.5 VDD - 0.4 1.4 VDD - 1.5 VDD - 0.5 10 10 VDD - 1.62 VDD - 0.88 900 300 300 50 Unit V V V V V A A Test Condition Input High Voltage, Differential Inputs 1 V V mV pS pS pS Note: 1. Assuming a differential input voltage of at least 100 mV. 2. Unused differential input terminated to VDD-1.4 V. 3. With 50 load on each pin to VDD-2 V, i.e. 82 to GND and 130 to VDD. Electrical Specifications 155 June 19, 2006 IDT82V3280 WAN PLL 9.3.3.2 LVDS Input / Output Port 50 (transmission line) 2 kHz to 667 MHz 100 50 (transmission line) IN5_NEG OUT6_POS IN5_POS OUT6_NEG 50 (transmission line) 100 50 (transmission line) 2 kHz to 667 MHz IN6_POS 2 kHz to 100 667 MHz IN6_NEG 50 (transmission line) 50 (transmission line) OUT7_POS OUT7_NEG 50 (transmission line) 100 50 (transmission line) 2 kHz to 667 MHz Figure 34. Recommended LVDS Input Port Line Termination Table 53: LVDS Input / Output Port Electrical Characteristics Parameter Description Min Figure 35. Recommended LVDS Output Port Line Termination Typ Max Unit Test Condition VCM VDIFF VIDTH RTERM VOH VOL VOD VOS RO RO VOD VOS ISA, ISB ISAB tRISE tFALL tSKEW Input Common-mode Voltage Range Input Peak Differential Voltage Input Differential Threshold External Differential Termination Impedance Output Voltage High Output Voltage Low Differential Output Voltage Output Offset Voltage Differential Output Impedance RO Mismatch between A and B Change in VOD between Logic 0 and Logic 1 Change in VOS between Logic 0 and Logic 1 Output Current Output Current Output Rise time (20% to 80%) Output Fall time (20% to 80%) Output Differential Skew 0 100 -100 95 1350 925 250 1125 80 1200 2400 900 100 mV mV mV mV mV mV mV % mV mV mA mA pS pS pS RLOAD = 100 1% RLOAD = 100 1% RLOAD = 100 1% RLOAD = 100 1% VCM = 1.0 V or 1.4 V VCM = 1.0 V or 1.4 V RLOAD = 100 1% RLOAD = 100 1% Driver shorted to GND Driver shorted together RLOAD = 100 1% RLOAD = 100 1% RLOAD = 100 1% 100 105 1475 1100 400 1275 100 120 20 25 25 24 12 200 200 300 300 50 Electrical Specifications 156 June 19, 2006 IDT82V3280 WAN PLL 9.4 JITTER & WANDER PERFORMANCE Table 54: Output Clock Jitter Generation Test Definition 1 Peak to Peak Typ RMS Typ Note Test Filter N x 2.048MHz without APLL N x 2.048MHz with T0/T4 APLL N x 1.544 MHz without APLL N x 1.544 MHz with T0/T4 APLL 44.736 MHz without APLL 44.736 MHz with T0/T4 APLL 34.368 MHz without APLL 34.368 MHz with T0/T4 APLL <2 ns <1 ns <2 ns <1 ns <1 ns <2 ns <1 ns <2 ns <200 ps <100 ps <200 ps <100 ps <100 ps <200 ps <100 ps <200 ps See Table 55: Output Clock Phase Noise for details See Table 55: Output Clock Phase Noise for details See Table 55: Output Clock Phase Noise for details See Table 55: Output Clock Phase Noise for details GR-253, G.813 Option 2 limit 0.1 UI p-p (1 UI-6430 ps) G.813 Option 1, G.812 limit 0.5 UI p-p (1 UI-6430 ps) G.813 Option 1 limit 0.1 UI p-p (1 UI-6430 ps) GR-253, G.813 Option 2 limit 0.1 UI p-p (1 UI-1608 ps) G.813 Option 1, G.812 limit 0.5 UI p-p (1 UI-1608 ps) G.813 Option 1, G.812 limit 0.1 UI p-p (1 UI-160 8ps) G.813 Option 1, G.812 limit 0.5 UI p-p (1 UI-402 ps) G.813 Option 1, G.812 limit 0.1 UI p-p (1 UI-402 ps) 20 Hz - 100 kHz 20 Hz - 100 kHz 10 Hz - 40 kHz 10 Hz - 40 kHz 100 Hz - 800 kHz 100 Hz - 800 kHz 10 Hz - 400 kHz 10 Hz - 400 kHz 12 kHz - 1.3 MHz 0.004 UI p-p 0.001 UI RMS OC-3 (Chip T0 DPLL + T0/T4 APLL) 6.48 MHz, 19.44 MHz, 25.92 0.004 UI p-p 0.001 UI RMS MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz, 622.08 MHz output 0.001 UI p-p 0.001 UI RMS 500 Hz - 1.3 MHz 65 kHz - 1.3 MHz 0.018 UI p-p 0.007 UI RMS OC-12 (Chip T0 DPLL + T0/T4 APLL) 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 0.028 UI p-p 0.009 UI RMS 311.04 MHz, 622.08 MHz output + Intel GD16523 + Optical transceiver) 0.002 UI p-p 0.001 UI RMS STM-16 0.162 UI p-p 0.03 UI RMS (Chip T0 DPLL + T0/T4 APLL) 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz, 155.52 MHz, 311.04 MHz, 622.08 MHz output + Intel GD16523 + Optical 0.01 UI p-p 0.009 UI RMS transceiver) Note: 1. CMAC E2747 TCXO is used. 12 kHz - 5 MHz 1 kHz - 5 MHz 250 kHz - 5 MHz 5 kHz - 20 MHz 1 MHz - 20 MHz Electrical Specifications 157 June 19, 2006 IDT82V3280 WAN PLL Table 55: Output Clock Phase Noise Output Clock 1 @100Hz Offset Typ @1kHz Offset Typ @10kHz Offset @100kHz Offset Typ Typ @1MHz Offset @5MHz Offset Typ Typ Unit 622.08 MHz (T0 DPLL + T0/T4 APLL) 155.52 MHz (T0 DPLL + T0/T4 APLL) 38.88 MHz (T0 DPLL + T0/T4 APLL) 16E1 (T0/T4 APLL) 16T1 (T0/T4 APLL) E3 (T0/T4 APLL) T3 (T0/T4 APLL) Note: 1. CMAC E2747 TCXO is used. -70 -82 -94 -94 -95 -93 -92 -86 -98 -110 -110 -112 -109 -108 -95 -107 -118 -118 -120 -116 -116 -100 -112 -124 -125 -127 -124 -122 -107 -119 -131 -131 -132 -131 -126 -128 -140 -143 -142 -143 -138 -141 dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz Table 56: Input Jitter Tolerance (155.52 MHz) Jitter Frequency Jitter Tolerance Amplitude (UI p-p) Table 58: Input Jitter Tolerance (2.048 MHz) Jitter Frequency Jitter Tolerance Amplitude (UI p-p) 12 Hz 178 Hz 1.6 mHz 15.6 mHz 0.125 Hz 19.3 Hz 500 Hz 6.5 kHz 65 kHz 1.3 MHz > 2800 > 2800 > 311 > 311 > 39 > 39 > 1.5 > 1.5 > 0.15 > 0.15 1 Hz 5 Hz 20 Hz 300 Hz 400 Hz 700 Hz 2400 Hz 10 kHz 50 kHz 100 kHz 150 140 130 40 33 18 5.5 1.3 0.4 0.4 Table 57: Input Jitter Tolerance (1.544 MHz) Jitter Frequency Jitter Tolerance Amplitude (UI p-p) Table 59: Input Jitter Tolerance (8 kHz) Jitter Frequency Jitter Tolerance Amplitude (UI p-p) 1 Hz 5 Hz 20 Hz 300 Hz 400 Hz 700 Hz 2400 Hz 10 kHz 40 kHz 150 140 130 38 25 15 5 1.2 0.5 1 Hz 5 Hz 20 Hz 300 Hz 400 Hz 700 Hz 2400 Hz 3600 Hz 0.8 0.7 0.6 0.16 0.14 0.07 0.02 0.01 Electrical Specifications 158 June 19, 2006 IDT82V3280 WAN PLL Table 60: T0 DPLL Jitter Transfer & Damping Factor 3 dB Bandwidth Programmable Damping Factor Table 61: T4 DPLL Jitter Transfer & Damping Factor 3 dB Bandwidth Programmable Damping Factor 0.5 mHz 1 mHz 2 mHz 4 mHz 8 mHz 15 mHz 30 mHz 60 mHz 0.1 Hz 0.3 Hz 0.6 Hz 1.2 Hz 2.5 Hz 4 Hz 8 Hz 18 Hz 35 Hz 70 Hz 560 Hz 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 18 Hz 35 Hz 70 Hz 560 Hz 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 1.2, 2.5, 5, 10, 20 Electrical Specifications 159 June 19, 2006 IDT82V3280 WAN PLL 9.5 OUTPUT WANDER GENERATION template template tested result tested result Figure 36. Output Wander Generation Electrical Specifications 160 June 19, 2006 IDT82V3280 WAN PLL 9.6 INPUT / OUTPUT CLOCK TIMING The inputs and outputs are aligned ideally. But due to the circuit delays, there is delay between the inputs and outputs. 8 kHz Input Clock t1 8 kHz Output Clock 6.48 MHz Input Clock 6.48 MHz Output Clock t2 19.44 MHz Input Clock 19.44 MHz Output Clock t3 25.92 MHz Input Clock 25.92 MHz Output Clock t4 38.88 MHz Input Clock 38.88 MHz Output Clock t5 51.84 MHz Input Clock 51.84 MHz Output Clock t6 Figure 37. Input / Output Clock Timing Table 62: Input/Output Clock Timing 3 Symbol Typical Delay 1 (ns) Peak to Peak Delay Variation 2 (ns) t1 t2 t3 t4 t5 t6 4 1 1 2 1.4 3 1.6 1.6 1.6 1.6 1.6 1.6 Note: 1. Typical delay provided as reference only. 2. `Peak to Peak Delay Variation' is the delay variation that is guaranteed not to be exceeded for IN11 in Master/Slave operation. 3. Tested when IN11 is selected. Electrical Specifications 161 June 19, 2006 IDT82V3280 WAN PLL 9.7 OUTPUT CLOCK TIMING MFRSYNC_2K/ FRSYNC_8K N X T1 (1.544 MHz) N X E1 (2.048 MHz) E3 (34.368 MHz) T3 (44.736 MHz) 6.48 MHz 19.44 MHz 25.92 MHz 38.88 MHz 51.84 MHz 77.76 MHz 155.52 MHz 311.04 MHz 622.08 MHz t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 Table 63: Output Clock Timing Symbol Typical Delay (ns) Peak to Peak Delay Variation (ns) t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 1.5 1.5 (not recommended to use) 1.5 (not recommended to use) Electrical Specifications 162 June 19, 2006 Glossary 3G ADSL APLL ATM BITS CMOS DCO DPLL DSL DSLAM DWDM EPROM GPS GSM IIR IP ISDN JTAG LPF LVDS MTIE MUX OBSAI OC-n PBO PDH ----------------------------------------------------- Third Generation Asymmetric Digital Subscriber Line Analog Phase Locked Loop Asynchronous Transfer Mode Building Integrated Timing Supply Complementary Metal-Oxide Semiconductor Digital Controlled Oscillator Digital Phase Locked Loop Digital Subscriber Line Digital Subscriber Line Access MUX Dense Wavelength Division Multiplexing Erasable Programmable Read Only Memory Global Positioning System Global System for Mobile Communications Infinite Impulse Response Internet Protocol Integrated Services Digital Network Joint Test Action Group Low Pass Filter Low Voltage Differential Signal Maximum Time Interval Error Multiplexer Open Base Station Architecture Initiative Optical Carried rate, n = 1, 3, 12, 48, 192, 768; 51 Mbit/s, 155 Mbit/s, 622 Mbit/s, 2.5 Gbit/s, 10 Gbit/s, 40 Gbit/s. Phase Build-Out Plesiochronous Digital Hierarchy Glossary 163 June 19, 2006 IDT82V3280 WAN PLL PECL PFD PLL RMS PRS SDH SEC SMC SONET SSU STM TCM-ISDN TDEV UI WLL ------------------------------- Positive Emitter Coupled Logic Phase & Frequency Detector Phase Locked Loop Root Mean Square Primary Reference Source Synchronous Digital Hierarchy SDH / SONET Equipment Clock SONET Minimum Clock Synchronous Optical Network Synchronization Supply Unit Synchronous Transfer Mode Time Compression Multiplexing Integrated Services Digital Network Time Deviation Unit Interval Wireless Local Loop Glossary 164 June 19, 2006 Index A AMI Violation ...................................................................................... 20 Averaged Phase Error ........................................................................ 34 Fine Phase Loss ................................................................................ 27 Frequency Hard Alarm .................................................................24, 29 Frequency Hard Alarm Threshold ...................................................... 24 B Bandwidths and Damping Factors ..................................................... 34 Acquisition Bandwidth and Damping Factor ............................... 34 Locked Bandwidth and Damping Factor ..................................... 34 Starting Bandwidth and Damping Factor .................................... 34 H Hard Limit ........................................................................................... 27 Holdover Frequency Offset ................................................................ 35 I IIR ...................................................................................................... 35 Input Clock Frequency ....................................................................... 24 Input Clock Selection ......................................................................... 25 Automatic selection ..............................................................26, 29 External Fast selection .........................................................25, 29 Forced selection ...................................................................26, 29 Internal Leaky Bucket Accumulator ................................................... 23 Bucket Size ................................................................................ 23 Decay Rate ................................................................................ 23 Lower Threshold ........................................................................ 23 Upper Threshold ........................................................................ 23 C Calibration .......................................................................................... 19 Coarse Phase Loss ............................................................................ 27 Crystal Oscillator ................................................................................ 19 Current Frequency Offset ................................................................... 34 D DCO ................................................................................................... 34 Division Factor .................................................................................... 21 DPLL Hard Alarm ............................................................................... 27 DPLL Hard Limit ................................................................................. 27 DPLL Operating Mode ................................................................. 34, 35 Free-Run mode ................................................................... 34, 35 Holdover mode .................................................................... 34, 35 Automatic Fast Averaged ................................................... 35 Automatic Instantaneous .................................................... 35 Automatic Slow Averaged .................................................. 35 Manual ................................................................................ 35 Locked mode ....................................................................... 34, 35 Temp-Holdover mode ......................................................... 34 Lost-Phase mode ....................................................................... 34 Pre-Locked mode ....................................................................... 34 Pre-Locked2 mode ..................................................................... 35 DPLL Soft Alarm ................................................................................. 27 DPLL Soft Limit .................................................................................. 27 L Limit ................................................................................................... 37 LOS ..............................................................................................23, 29 LPF .................................................................................................... 34 M Master / Slave Application ................................................................. 47 Master / Slave Configuration .............................................................. 44 Master Clock ...................................................................................... 19 Microprocessor Interface ................................................................... 48 microprocessor interface EPROM ...................................................................................... 49 Intel ............................................................................................ 52 Motorola ..................................................................................... 54 Multiplexed ................................................................................. 50 Serial .......................................................................................... 56 E External Sync Alarm ........................................................................... 42 F Fast Loss ............................................................................................ 27 N No-activity Alarm ..........................................................................23, 29 Index 165 June 19, 2006 IDT82V3280 WAN PLL P PBO .................................................................................................... 37 PFD .................................................................................................... 34 Phase Lock Alarm ....................................................................... 28, 29 Phase Offset ....................................................................................... 37 Phase-compared ......................................................................... 27, 37 Phase-time ......................................................................................... 37 Pre-Divider ......................................................................................... 21 DivN Divider ................................................................................ 21 HF Divider ................................................................................... 21 Lock 8k Divider ........................................................................... 21 R Reference Clock ................................................................................ 24 S Selected Input Clock Switch .............................................................. 29 Non-Revertive switch ................................................................. 30 Revertive switch ......................................................................... 29 State Machine ..............................................................................31, 33 V Validity ............................................................................................... 29 Index 166 June 19, 2006 IDT82V3280 WAN PLL ORDERING INFORMATION IDT XXXXXXX Device Type XX X Process/ Temperature Range Blank Industrial (-40 C to +85 C) PF PFG DQ DQG 82V3280 Thin Quad Flatpack (TQFP, PN100) Green Thin Quad Flatpack (TQFP, PNG100) Thermal Enhanced Thin Quad Flatpack, ExposedPadTM (TQFP, DQ100) Green Thermal Enhanced Thin Quad Flatpack, ExposedPadTM (TQFP, DQG100) WAN PLL DATASHEET DOCUMENT HISTORY 09/28/2005 pgs. 152. 06/19/2006 pgs. 46 CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 www.idt.com 167 for SALES: 1-800-345-7015 or 408-284-8200 fax: 408-284-2775 for Tech Support: 408-360-1552 email:telecomhelp@idt.com IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. |
Price & Availability of IDT82V3280
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |