![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
oH V SC A V E R OM AI SIO PL LA N IA B L S NT E TISP4300MMAJ, TISP4350MMAJ, TISP4360MMAJ TISP4300MMBJ, TISP4350MMBJ, TISP4360MMBJ BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS *R TISP43xxMMAJ/BJ Overvoltage Protector Series Specified for: - ITU-T Recommendation K.21 10/700 AC Induction and Contact - FCC Part 68 (TIA/EIA-IS-968) Type A & B Surge - UL 60950 and CSA 22.2 No.60950 Clause 6. Power Cross - Telcordia GR-1089-CORE 2/10 and 10/1000 AC Induction and Contact Applications: TISP4300MM for: POTS Solid-State Relay Modems Protection Voltage .............................................................. 300 V TISP4350MM for: POTS Electro-mechanical Relay Modems FCC Type B Ringer Voltage ............................................... 275 V TISP4360MM for: ADSL Modems ADSL + Type B Ringer Voltage .......................................... 290 V Ion-Implanted Breakdown Region Precise and Stable Voltage SMA Package (Top View) R (B) 1 2 T (A) MDXXCCE SMB Package (Top View) R(B) 1 2 T(A) MDXXBGF Device Symbol T Device `4300 `4350 `4360 VDRM V 230 275 290 V(BO) V 300 350 360 SD4XAA R Terminals T and R correspond to the alternative line designators of A and B Available in SMA and SMB Packages SMA Saves 25 % Placement Area Over SMB FCC Part 68 Type A Surge Compliance by Using Either a Fuse or 7 Resistor ............................................ UL Recognized Components Rated for International Surge Wave Shapes Wave Shape 2/10 s 10/160 s 9/720 s 10/700 s 10/560 s 10/1000 s Standard GR-1089-CORE FCC Part 68 FCC Part 68 ITU-T K.20/45/ 21 FCC Part 68 GR-1089-CORE ITSP A 250 75 65 65 55 50 Description These devices are designed to limit overvoltages on the telephone line. Overvoltages are normally caused by a.c. power system or lightning flash disturbances which are induced or conducted on to the telephone line. A single device provides 2-point protection and is typically used for the protection of 2-wire telecommunication equipment (e.g. between the Ring and Tip wires for telephones and modems). Combinations of devices can be used for multi-point protection (e.g. 3-point protection between Ring, Tip and Ground). How To Order For Standard Termination Finish Order As For Lead Free Termination Finish Order As TISP43xxMMAJR-S TISP43xxMMBJR-S Device TISP43xxMM Package SMA/DO-214AC J-Bend (AJ) SMB/DO-214AA J-Bend (BJ) Carrier Embossed Tape Reeled TISP43xxMMAJR (R) TISP43xxMMBJR *RoHS Directive 2002/95/EC Jan 27 2003 including Annex NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Description (Continued) The protector consists of a symmetrical voltage-triggered bidirectional thyristor. Overvoltages are initially clipped by breakdown clamping until the voltage rises to the breakover level, which causes the device to crowbar into a low-voltage on state. This low-voltage on state causes the current resulting from the overvoltage to be safely diverted through the device. The high crowbar holding current prevents d.c. latchup as the diverted current subsides. This TISP43xxMM range consists of three voltage variants targeted at specific applications: ADSL, electro-mechanical hook switch and solid state hook switch modems. These parts are guaranteed to voltage limit and withstand the listed international lightning surges in both polarities. Two packages are available; SMB (JEDEC DO-214AA with J-bend leads) and SMA (JEDEC DO-214AC with J-bend leads). These devices are supplied in embossed tape reel carrier pack. For alternative voltage and holding current values, consult the factory. Absolute Maximum Ratings, TA = 25 C (Unless Otherwise Noted) Rating Repetitive peak off-state voltage, Non-repetitive peak on-state pulse current (see Notes 2, 3 and 4) 2/10 s (GR-1089-CORE, 2/10 s voltage wave shape) 10/160 s (FCC Part 68 (TIA/EIA-IS-968), 10/160 s voltage wave shape) 5/320 s (FCC Part 68 (TIA/EIA-IS-968), 9/720 s voltage wave shape) 5/310 s (ITU-T K.44, 10/700 s voltage wave shape used in K.20/45/21) 10/560 s (FCC Part 68 (TIA/EIA-IS-968), 10/560 s voltage wave shape) 10/1000 s (GR-1089-CORE, 10/1000 s voltage wave shape) Non-repetitive peak on-state current (see Notes 2, 3 and 4) 20 ms (50 Hz) full sine wave 1 s (50 Hz) full sine wave 1000 s 50 Hz/60 Hz a.c. Junction temperature Storage temperature range NOTES: 1. 2. 3. 4. `4300 `4350 `4360 Symbol VDRM Value 230 275 290 250 75 65 65 55 50 18 7 1.6 -40 to +150 -65 to +150 Unit V ITSP A ITSM TJ Tstg A C C For voltage values at lower temperatures derate at 0.13 %/C. Initially, the TISP43xxMM must be in thermal equilibrium with TJ = 25 C. The surge may be repeated after the TISP43xxMM returns to its initial conditions. EIA/JESD51-2 environment and EIA/JESD51-3 PCB with standard footprint dimensions connected with 5 A rated printed wiring track widths. Derate current values at -0.61 %/C for ambient temperatures above 25 C. Overload Ratings, TA = 25 C (Unless Otherwise Noted) Rating Peak overload on-state current, Type A impulse (see Note 5) 10/160 s 10/560 s Peak overload on-state current, a.c. power cross tests UL 60950 (see Note 5) Symbol Value 200 100 See Figure 10 for current versus time Unit IT(OV)M A IT(OV)M A NOTE 5: These electrical stress levels may damage the TISP43xxMM silicon chip. After test, the pass criterion is either that the device is functional or, if it is faulty, that it has a short circuit fault mode. In the short circuit fault mode, the following equipment is protected as the device is a permanent short across the line. The equipment would be unprotected if an open circuit fault mode developed. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Recommended Operating Conditions Component series resistor for FCC Part 68, 10/160, 10/560 type A surge survival series resistor for FCC Part 68, 9/720 type B surge survival RS series resistor for GR-1089-CORE first-level and second-level surge survival series resistor for K.20, K.21 and K.45 1.5 kV, 10/700 surge survival series resistor for K.21 coordination with a 400 V primary protector Min 13 0 15 0 6.6 Typ Max Unit Electrical Characteristics for the R and T Terminals, TA = 25 C (Unless Otherwise Noted) Parameter Repetitive peak offstate current Breakover voltage Breakover current Holding current Critical rate of rise of off-state voltage Off-state current Off-state current Off-state capacitance Test Conditions VD = VDRM TA = 25 C TA = 85 C `4300 `4350 `4360 0.15 5 Min Typ Max 5 10 300 350 360 0.8 0.6 Unit A IDRM V(BO) I(BO) IH dv/dt dv/dt = 250 V/ms, RSOURCE = 300 dv/dt = 250 V/ms, RSOURCE = 300 IT = 5 A, di/dt = -/+30 mA/ms Linear voltage ramp, Maximum ramp value < 0.85VDRM `4300, VD = 207 V `4350, VD = 248 V `4360, VD = 261 V VD = 50 V f = 1 MHz, Vd = 1 V rms, VD = 1 V f = 1 MHz, Vd = 1 V rms, VD = 50 V V A A kV/s ID ID Coff 2 10 40 18 A 10 pF Thermal Characteristics Parameter Test Conditions EIA/JESD51-3 PCB, IT = ITSM(1000), TA = 25 C, (see Note 6) 265 mm x 210 mm populated line card, 4-layer PCB, IT = ITSM(1000), TA = 25 C 52 Min Typ Max 115 C/W Unit RJA Junctio n to free air thermal resistance NOTE 6: EIA/JESD51-2 environment and PCB has standard footprint dimensions connected with 5 A rated printed wiring track widths. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Parameter Measurement Information +i ITSP Quadrant I Switching Characteristic ITSM IT VT IH V(BO) I(BO) -v IDRM VDRM VD ID ID VD VDRM IDRM +v I(BO) IH V(BO) VT IT ITSM Quadrant III Switching Characteristic ITSP -i PMXXAAB Figure 1. Voltage-current Characteristic for T and R Terminals All Measurements are Referenced to the R Terminal NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Typical Characteristics OFF-STATE CURRENT vs JUNCTION TEMPERATURE 10 VD = 50 V Normalized Breakover Voltage 1.10 TC4LAG 1.15 NORMALIZED BREAKOVER VOLTAGE vs JUNCTION TEMPERATURE TC4LAF |ID| - Off-State Current - A 1 1.05 0*1 1.00 0*01 0.95 0*001 -25 0 25 50 75 100 125 TJ - Junction Temperature - C 150 0.90 -25 0 25 50 75 100 125 TJ - Junction Temperature - C 150 Figure 2. ON-STATE CURRENT vs ON-STATE VOLT AGE 50 40 30 20 15 10 7 5 4 3 2 1.5 1 0.7 0.5 0.7 0.4 1 1.5 2 31 4 5 VT - On-State Voltage - V 7 0 -25 TA = 25 C tW = 100 s Normalized Holding Current Figure 3. NORMALIZED HOLDING CURRENT vs JUNCTION TEMPERATURE TC4LAD TC4MAN 2.0 1.5 IT - On-State Current - A 1.0 0.9 0.8 0.7 0.6 0.5 0 25 50 75 100 TJ - Junction Temperature - C 125 150 Figure 4. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. Figure 5. TISP43xxMMAJ/BJ Overvoltage Protector Series Typical Characteristics NORMALIZED CAPACITANCE vs OFF-STATE VOLTAGE TC4LAH 1 |Coff(+VD) - Coff(-VD)| -- Capacitance Asymmetry - pF 0.9 0.8 Capacitance Normalized to VD = 0 0.7 0.6 0.5 0.4 TJ = 25 C Vd = 1 Vrms TYPICAL CAPACI TANCE ASYMMETRY vs OFF-STATE VOLTAGE TC4LBB 1 Vd = 10 mV rms, 1 MHz 0.3 Vd = 1 V rms, 1 MHz 0 1 2 3 4 51 7 0 20 30 40 50 VD -- Off-State Voltage - V 0.2 0.5 1 2 3 5 10 20 30 VD - Off-state Voltage - V 50 100150 Figure 6. Figure 7. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Rating and Thermal Information NON-REPETITIVE PEAK ON-STATE CURRENT vs CURRENT DURATION ITSM(t) - Non-Repetitive Peak On-State Current - A 20 15 TI4LAI VDRM DERATING FACTOR vs MINIMUM AMBIENT TEMPERATURE 1.00 TI4LAE Derating Factor 0.1 1 t - Current Duration - s 10 100 10 9 8 7 6 5 4 3 VGEN = 600 Vrms, 50/60 Hz RGEN = 1.4*VGEN/ITSM(t) EIA/JESD51-2 ENVIRONMENT EIA/JESD51-3 PCB TA = 25 C 0.99 0.98 0.97 0.96 0.95 0.94 0.93 -40 -35 -30 -25 -20 -15 -10 -5 2 1.5 0.01 0 5 10 15 20 25 TAMIN - Minimum Ambient Temperature - C Figure 8. PEAK OVERLOAD ON-STATE CURRENT vs CURRENT DURATION TI4MAM DEVICE WILL CARRY CURRENT OF TESTS 1 THRU 5 CLAUSE 6.4, UL 60950, FOR FULL TEST TIME Figure 9. IT(OV)M -- Peak Overload On-State Current -- A rms 40 35 30 25 20 15 40 A 100 A2s 7A 10 9 8 7 6 5 4 3.5 3 2.5 2 0*01 0*1 WIRING SIMULATOR 2.2 A 1 10 t - Current Duration - s 100 1000 Figure 10. Peak Overload On-State Current against Duration NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series APPLICATIONS INFORMATION FCC Part 68, ACTA, TIA and EIA From 2001, the registrations for FCC equipment changed from the FCC to ACTA, Administrative Council for Terminal Attachments. For this function, ACTA needed to adopt a US National standard specifying terminal equipment requirements. The TIA, Telecommunications Industry Association, in conjunction with the EIA, Electronic Industries Alliance, created TIA/EIA-IS-968 for this purpose. The first issue of TIA/EIA-IS-968 is essentially a renumbered version of the FCC Part 68 requirement. Clause and figure changes are shown in the table. Item Telephone Line Surge - Type A Telephone Line Surge - Type B Simplified Surge Generator Open Circuit voltage Wave shape Short Circuit Current Wave shape FCC Part 68 TIA/EIA-IS-968 Clause 68.302 (b) Clause 4.2.2 Clause 68.302 (c) Fig. 68.302 (a) Fig. 68.302 (b) Fig. 68.302 (c) Clause 4.2.3 Figure 4.1 Figure 4.2 Figure 4.3 TIA/EIA-IS-968 (FCC Part 68) Impulse Testing To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms. The table below shows values for the TIA/EIA-IS-968 and ITU-T recommendation K.21. Test Standard Condition V Longitudinal TIA/EIA-IS-968 (F CC Part 68) ITU-T K.21 Basic Level ITU-T K.21 Enhanced Level Metallic Longitudinal Metallic Transverse Transverse Peak Voltage V 1500 800 1500 1000 1500 4000 1500 6000 Voltage Wave Form s 10/160 10/560 9/720 9/720 10/700 10/700 Peak Current A 200 100 37.5 25 37.5 100 37.5 125 Current Wave Form s 10/160 10/560 5/320 5/320 5/310 5/310 Fictive Impedance 7.5 8 40 40 40 40 TISP43xxMM Rating A 75 55 65 65 65 65 Series Resista nce 2 x 13 7 0 0 0 6.6 0 6.2 TIA/EIA-IS-968 terminology for the wave forms produced by the ITU-T recommendation K.21 10/700 impulse generator Values assume the TISP43xxMM is connected inter-conductor and a 400 V primary is used If the impulse generator current exceeds the protector's current rating then a series resistance can be used to reduce the current to the protector's rated value to prevent possible failure. For the new edition of ITU-T recommendation K.21 (2000) some series resistance might be needed to pass the impulse coordination test. The value for a 400 V primary protector is given in the table. The required value of device survival series resistance for a given waveform is given by the following calculations. First, the minimum total circuit impedance is found by dividing the impulse generator's peak voltage by the protector's rated current. The impulse generator's fictive impedance (generator's peak voltage divided by peak short circuit current) is then subtracted from the minimum total circuit impedance to give the required value of series resistance. For the TIA/EIA-IS-968 10/560 waveform the following values result. The minimum total circuit impedance is 800/55 = 15 and the generator's fictive impedance is 800/100 = 8 . For an inter-conductor connected TISP43xxMM, this gives a minimum series resistance value of 15 - 8 = 7 . The 10/160 waveform only needs to be considered if the TISP43xxMM is connected from the conductor to ground. In this case the conductor series resistance is 12.5 per conductor. Fuse Values for TIA/EIA-IS-968 (FCC Part 68) Fuses must not operate on the Type B surge. To survive a 37.5 A Type B surge, the fuse needs to have a melting I2t of greater than 0.7 A2s. To survive the Type A surges a fuse melting I2t value of greater than 10 A 2s for 10/160 and 8 A2s for 10/560 is needed. By using a fuse which does not operate on Type B surges (I 2t > 0.7 A2s) and does operate on Type A surges (I 2t < 8 A2s) a non-operational pass can be achieved for Type A testing. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series TIA/EIA-IS-968 (FCC Part 68) System Voltage Levels The protector should not clip or limit the voltages that occur in normal system operation. If the maximum system voltages are not known, then designers often used the voltages for the FCC Part 68 "B" ringer. The "B" ringer has a d.c. voltage of 56.5 V and a maximum a.c. ring voltage of 150 V rms. The resultant waveform is shown in Figure 11. The maximum voltage is -269 V, but, because of possible wiring reversals, the protector should have a working voltage of 269 V minimum. The TISP4350MM protector meets this requirement with a working voltage, VDRM, of 275 V and a protection voltage, V (BO), of 350 V. Figure 12 shows the TISP4350MM voltages relative to the POTS -269 V peak ringing voltage. 200 V +156 V 100 V -230 -240 -250 -260 -270 -280 -275 V -269 V RINGING PEAK WORKING VOLTAGE VDRM 0 -56.5 V d.c. -100 V -290 -300 -310 -320 -330 -340 -350 -269 V -360 AI4XAD TISP4350MM -200 V -350 V PROTECTION VOLT AGE V(BO) AI4HAEA -300 V -370 Figure 11. ADSL System Voltage Levels Figure 12. The ADSL signal can be as high as 15 V and this adds to the POTS signal making a peak value of -284 V. This increased signal value of -284 V would be clipped by the TISP4350MM, which only allows for a -275 V signal. The TISP4360MM has been specified to overcome this problem by having a higher working voltage of 290 V. Figure 13 shows the TISP4360MM voltages relative to the -284 V peak ADSL plus POTS ringing voltage. The 15 V ADSL signal is shown as a gray band in Figure 13. -230 -240 -250 -260 -270 -280 -290 -300 -310 -320 -330 -340 -350 -360 -370 -360 V -290 V -284 V PEAK ADSL + RINGING WORKING VOLTAGE VDRM TISP4360MM PROTECTION VOLT AGE V(BO) AI4HAFA NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. Figure 13. TISP43xxMMAJ/BJ Overvoltage Protector Series IEC 60950, UL 1950/60950, CSA C22.2 No. 950/60950 and EN 60950 These electrical safety standards for IT (Information Technology) equipment at the customer premise use the IEC (International Electrotechnical Commission) 60950 standard as the core document. The IEC 60950 covers fundamental safety criteria such as creepage and isolation. The connection to a telecommunication network voltage (TNV) is covered in clause 6. Europe is harmonized by CENELEC (Comite Europeen de Normalization Electro-technique) under EN 60950 (included in the Low Voltage Directive, CE mark). Up to the end of 2000, the US had UL (Underwriters Laboratories) 1950 and Canada CSA (Canadian Standards Authority) C22.2 No. 950. The US and Canadian standards include regional changes and additions to the IEC 60950. A major addition is the inclusion of clause 6.6, power cross withstand containing the flowchart Figure 18b and annex NAC covering testing. Remarks made for UL 1950 will generally be true for CSA 22.2 No. 950. In December 2000, UL released UL 60950, which will run concurrently with UL 1950 until 2003, after which submittals can only be made for UL 60950. The equivalent Canadian document is designated CSA C22.2 No. 60950. Changes and differences between UL 1950 and UL 60950 do not affect power cross testing nor evaluation criteria. Clause and figure numbering has changed between the standards and these changes are shown in the table. In this document, these two standards are being jointly referred to as UL 60950 and the clause and figure numbering referenced will be from UL 60950. Item Protection against overvoltage from power line crosses Overvoltage flowchart UL 1950 Figure 18b UL 60950 Figure 6C Clause 6.6 Clause 6.4 UL 60950, Clause 6.4 - Power Cross Figure 14 shows the criterion flow for UL 60950 power cross. (This is a modified version of UL60950, Figure 6C -- Overvoltage flowchart.) There are many routes for achieving a pass result. For discussion, each criterion has been given a letter reference. Brief details of any electrical testing is given as a criterion note. Test pass criteria are given in the bottom table of Figure 14. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series IT Equipment parameters UL 60950 (12/2000) Telecommunication network connection Clause 6.4 -- Protection against overvoltage from power line crosses Figure 6C -- Overvoltage flowchart Annex NAC (normative) -- Power line crosses A No Test 1. 600 V, 40 A, 1.5 s No overvoltage testing Connects to outside cable Yes Has 100 A 2s B No @ 600 V ) Has min. 26 AWG supplied cord E No Pass Test 1 I No Test 5. 120 V, 25 A, 30 min or open circuit Yes Yes Yes Has 1.3 A C No d.c. limiting ) Pass 6.3.3 ground/line separation ) F No Pass test 5 J No Fail Yes Test 2. ) 600 V, 7 A, 5 s Test 3. # ) 600 V, 2.2 A, 30 min or open circuit (3A) Test 3A. # ) 600 V, <3.3 A, 30 min, no open circuit Test 4. # ) < Limiting voltage, <2.2 A, 30 min, no open circuit, no overvoltage protector voltage limiting Yes Yes Has fire enclosure and spacings G Yes No No Has fire enclosure D No Pass test 2 pass tests 3, 4 H Yes Pass Yes NOTES ) Overcurrent protector I2 t must be lower than any other equipment element which carries the same current. ) UL accepts that a fuse with a 1 A or less rating meets the 1.3 A criterion. ) Pass for 120 V a.c. between telecommunication line and ground current < 10 mA. ) Test 2 not required if the equipment d.c. breaking is 1.3 A or less, see comment ). # ) Tests 3 and 4 not required for equipment with less than 1000 m of outside cable. Pass criteria No cheesecloth charring Insulation OK Wiring simulator (fuse) OK I2 t < 100 A 2s @ 600 V a.c. Test 1 Test 2 Test 3 Test 3A Test 4 Test 5 Users must verify requirements against latest issue of UL 60950 AIUL60950A Figure 14. UL 60950 Power Cross Flow Chart NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Power Cross Pass Routes This discussion covers typical modem flows. Flow Comment No tests A Y N Box A The criterion for box A is if the modem connects to an outside TNV line. The majority of modems will be connected to an outside line, so the answer is yes. The yes path goes to box B. B A Y B Y N E C Box B The criterion for box B is if the equipment has a limit of 100 A2s at 600 V rms for Test 1. Many interpret this as a fuse with I2t 100 A2s and often miss the 600 V a.c. breaking requirement. However, the current loop is comp leted by the fuse and other equipment compon ents. To ensure that the fuse I2t sets the equipment performance, the other current loop componen ts, such as the printed wiring (PW), must have higher I2t values than the fuse. Certainly the fuse I2t needs to be lower than 100 A2s but other compon ents, for example IC packaging, may impose a hazard-free limit of 10 A2s. (This conflicts with TIA/ EIA-IS-968 Type A surge pass requirement of 8 A2s.) A yes leads to box C and a no to box E. E Y N I Y N Boxes E and I The criterion for box E is for a minimum telecommunications line cord of No. 26 AWG to be supplied or specified. Fail F A yes leads to box F and a no to box I. The criterion for box I is to pass Test 1. If all the four pass criteria of Test 1 are met, this is a yes and the flow goes to box F. A no result fails the equipment. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Power Cross Pass Routes (Continued) Flow Comment A Y B Y Boxes C and D The criterion for box C is overcurrent protection that reduces currents above 1.3 A. This requirement is met by a 1 A fuse (a 1 A current fusing rating, not an IEC 1 A current carrying rating). Modems which pass FCC Part 68 Type B surges and non-operationally pass Type A surges can use a fuse of 1 A or less, so the yes path to box D can be followed. High performance modems which operationally pass both Type A and B surges would need a fuse of greater than 1 A and so follow the no path to box F. The criterion for box D is a fire enclosure. C Y N F D Y N H Pass Few modems can afford fire enclosures. However, for an internal modem in a known comp uter case, the case may be evaluated as a fire enclosure. A successful case evaluation will give a yes and an equipment pass. More likely, the modem w ill not have a fire enclosure. The no flow goes to box H. F Y N J Y N Fail Boxes F and J The criterion for box F is a pass to clause 6.3.3 requirements. A yes goes to box G and a no goes to box J. The criterion for box J is to pass Test 5. If all the three pass criteria of Test 5 are met, this is a yes and the flow goes to box G. A no result fails the equipment. G Fail Boxes G and H The criterion for box G is a fire enclosure and spacings (See box D comments). A yes result passes the equipment and a no result leads to box H. The criterion for box H is to pass Tests 2, 3 and 4. Test 2 is not required if there is overcurrent protection that reduces currents above 1.3 A (See box C). High performance mod ems, using fuses and without fire enclosures, must pass tests 2, 3, possibly 3A if the fuse opens, and 4. For standard modems, using fuses of 1 A or less and without fire enclosures, tests 3, 3A and 4 must be passed. If the two pass criteria of each of the tests performed are met, this is a yes and the equipment passes. A no result fails the equipment. G N Y H N Y Pass NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Fuse Values for UL 1950/60950 Fuses for the UL 1950/60950 power cross need to break the specified currents at 600 V a.c. - ordinary fuses will not do! Fuse specification terms like short circuit capabilities to UL 1459 and UL 1950/60950, 40 A, 7 A and 2.2 A at 600 V a.c. ensure that the 600 V breaking is met. The requirement of Figure 14, box B, limits the fuse I2t to less than 100 A2s. Box C, with its 1.3 A limit gives a flow division. Modems passing the TIA/EIA-IS-968 Type A surge in a non-operational mode, could use a fuse of 1 A rating or less and satisfy the 1.3 A limit and move to box D. Modems operationally passing the Type A surge will tend to use a 1.25 A fuse, such as the Bel SMP 1.25, and move to box F. Fuses with ratings of 2 A and above may not operate before the wiring simulator fails (typically 3 A d.c.). TISP43xxMM and UL 1950/60950 Power Cross The TISP43xxMM conducts current for periods greater than the power cross test times, Figure 10, so the TISP43xxMM is not a major factor in UL 1950/60950 compliance. The main design task for UL 1950/60950 power cross is about enclosure design and the selection of the other components that are subject to power cross. A UL specified fuse together with a TISP43xxMM gives a simple design approach to meeting the power cross requirements. Summary of TISP4350MM, TISP4360MM and TISP4300MM Applications The TISP4350MM is designed to meet the FCC Part 68 Type B ringer voltages and is suitable for electro-mechanical hook switch POTS modems, Figure 15. For ADSL modems, the TISP4360MM should be used as it has an increased working voltage to avoid clipping the ADSL signal, Figure 16. The solid state hook switch used in POTS modems may be limited in voltage and dissipation capability. To reduce the voltage stress level on the solid state switch, a 300 V V(BO) TISP4300MM can be used, Figure 17. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series Application Circuits Protection F1 R Ring Detector Polarity Bridge Relay Fuse or 7 Resistor Th1 C1 R1 D5 D6 D1 D2 D3 D4 C2 Hook Switch C3 DC Sink T1 Signal T R2 TISP 4350MM D7 OC1 Isolation Barrier AI4MMAB Figure 15. Basic TISP4350MM Electro-Mechanical Hook Switch Protection F1 T Fuse or 7 Resistor Th1 C Tx Signal R TISP 4360MM AI4MMAA Figure 16. Basic TISP4360MM ADSL Interface Solid State Relay Isolation Barrier Protection Polarity Bridge F1 R Hook Switch Fuse or 7 Resistor D1 D2 Th1 D3 D4 Power OC1 Rx Signal T OC2 TISP 4300MM Ring Detector Tx Signal AI4MMAC Figure 17. Basic TISP4300MM Electronic Hook Switch Protection NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series MECHANICAL DATA Recommended Printed Wiring Land Pattern Dimensions SMA Land Pattern 2.34 (. 092) 1.90 (.075) 2.16 (.085) MILLIMETERS DIMENSIONS ARE: (INCHES) MDXX BIC SMB Land Pattern 2.54 (.100) 2.40 (.095) DIMENSIONS ARE: MILLIMETERS (INCHES) 2.16 (.085) MDXX BIB Device Symbolization Code Devices will be coded as below. As the device parameters are symmetrical, terminal 1 is not identified. SMA Package TISP4300MMAJ TISP4350MMAJ TISP4360MMAJ Symbolization Code 430MM 435MM 436MM SMB Package TISP4300MMBJ TISP4350MMBJ TISP4360MMBJ Symbolization Code 4300MM 4350MM 4360MM Carrier Information Devices are shipped in one of the carriers below. Unless a specific method of shipment is specified by the customer, devices will be shipped in the most practical carrier. For production quantities, the carrier will be embossed tape reel pack. Evaluation quantities may be shipped in bulk pack or embossed tape. Package SMA SMB Carrier Embossed Tape Reel Pack Standard Quantity 5000 3000 NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series MECHANICAL DATA SMA (DO-214AC) Plastic Surface Mount Diode Package This surface mount package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. SMA 4.06 - 4.57 (.160 - .180) 2.29 - 2.92 (.090 - .115) 2 Index Mark (if needed) 2.00 - 2.40 (.079 - .095) 0.76 - 1.52 (.030 - .060) 1.58 - 2.16 (.062 - .085) 4.83 - 5.59 (.190 - .220) 0.10 - 0.20 (.004 - .008) 1.27 - 1.63 (.050 - .064) DIMENSIONS ARE: MILLIMETERS (INCHES) MDXXCAA NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series MECHANICAL DATA Tape Dimensions SMA Package Single-Sprocket Tape 3.90 - 4.10 (.154 - .161) 1.95 - 2.05 (.077 - .081) 1.55 - 1.65 (.061 - .065) 1.65 - 1.85 (.065 - .073) 0.40 MAX. (.016) 5.45 - 5.55 (.215 - .219) 11.70 - 12.30 (.461 - .484) 8.20 MAX. (.323) 3.90 - 4.10 (.154 - .161) Direction of Feed 1.5 MIN. (.059) Carrier Tape Embossment 20 0 MIN. Cover Tape 4.50 MAX. (.177) Maximum component rotation Index Mark (If needed) Typical component cavity center line Typical component center line DIMENSIONS ARE: MILLIMETERS (INCHES) NOTES: A. The clearance between the component and the cavity must be within 0.05 mm (.002 in) MIN. to 0.65 mm (.026 in) MAX. so that the component cannot rotate more than 20 within the determined cavity. B. Taped devices are supplied on a reel of the following dimensions: Reel diameter: 330 mm 3.0 mm (12.99 in .12 in) Reel hub diameter: 75 mm (2.95 in) MIN. Reel axial hole: 13.0 mm 0.5 mm (.51 in .02 in) C. 5000 devices per reel. MDXXCGA NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series MECHANICAL DATA SMB (DO-214AA) Plastic Surface Mount Diode Package This surface mount package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. SMB 4.06 - 4.57 (.160 - .180) 3. 30 - 3. 94 (.130 - .155) 1 2 Index Mark (if needed) 2. 00 - 2.40 (.079 - .094) 0. 76 - 1.52 (.030 - .060) 5. 21 - 5.59 (.205 - .220) MILLIMETERS (INCHES) 1. 90 - 2.10 (.075 - .083) 0. 10 - 0. 20 (.004 - .008) 1. 96 - 2. 32 (.077 - .091) DIMENSIONS ARE: MDXXBHAB NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TISP43xxMMAJ/BJ Overvoltage Protector Series MECHANICAL DATA Tape Dimensions SMB Package Single-Sprocket Tape 3. 90 - 4.10 (.154 - .161 ) 1. 95 - 2.05 (.077 - .081) 1. 55 - 1.65 (.061 - .065 ) 1. 65 - 1.85 (.065 - .073 ) 0. 40 MAX . (.016) 5. 45 - 5.55 (.215 - .219 ) 11.70 - 12.30 (.461 - .484 ) 8. 20 MAX . (.323) 7. 90 - 8.10 (.311 - .319 ) Direction of Feed 1. 5 MIN . (.059) Carrier Tape Embossment 20 0 MIN . Cover Tape 4. 5 MAX . (.177) Maximium component rotation Index Mark (if needed) Typical component cavity center line Typical component center line NOTES: A. The clearance between the component and the cavity must be within 0.05 mm (.002 in) MIN. to 0.65 mm (.026 in) MAX. so that the component cannot rotate more than 20 within the determined cavity. B. Taped devices are supplied on a reel of the following dimensions: Reel diameter: 330 mm 3.0 mm (12.99 in .118 in) Reel hub diameter: 75 mm (2.95 in) MIN. Reel axial hole: 13.0 mm 0.5 mm (.512 in .020 in) C. 3000 devices are on a reel. MDXXBJA "TISP" is a trademark of Bourns, Ltd., a Bourns Company, and is Registered in U.S. Patent and Trademark Office. "Bourns" is a registered trademark of Bourns, Inc. in the U.S. and other countries. NOVEMBER 2001 - REVISED FEBRUARY 2005 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. |
Price & Availability of TISP4300MMAJR-S
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |