![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
INTEGRATED CIRCUITS 74F804, 74F1804 Hex 2-input NAND drivers Product specification IC15 Data Handbook 1990 Sep 14 Philips Semiconductors Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804/1804 FEATURES * High capacitive drive capability * Choice of configuration * Typical propagation delay of 2.5ns TYPE TYPICAL PROPAGATION DELAY 2.5ns 2.5ns TYPICAL SUPPLY CURRENT ( TOTAL) 9mA 9mA Corner VCC and GND - 74F804 Center VCC and GND - 74F1804 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS Dna - Dnb DESCRIPTION Data inputs 74F (U.L.) HIGH/LOW 1.0/0.033 LOAD VALUE HIGH/LOW 20A/20A Q0 - Q5 Data outputs 2400/80 48mA/48mA NOTE: One (1.0) FAST unit load is defined as: 20A in the high state and 0.6mA in the low state. 74F804 74F1804 ORDERING INFORMATION ORDER CODE DESCRIPTION 20-pin plastic DIP 20-pin plastic SOL COMMERCIAL RANGE VCC = 5V 10%, Tamb = 0C to +70C N74F804N, N74F1804N N74F804D, N74F1804D PKG DWG # SOT146-1 SOT163-1 PIN CONFIGURATION 74F804 D0a 1 D0b 2 Q0 3 D1a 4 D1b 5 Q1 6 D2a 7 D2b 8 Q2 9 GND 10 20 VCC 19 D5b 18 D5a 17 Q5 16 D4b 15 D4a 14 Q4 13 D3b 12 D3a 11 Q3 IEC/IEEE SYMBOL 74F804 1 2 4 5 7 8 12 13 15 16 18 19 17 14 11 9 6 & 3 SF00448 SF00450 LOGIC SYMBOL 74F804 PIN CONFIGURATION 74F1804 D4b 1 2 3 4 5 6 7 8 9 20 D4a 19 Q4 18 D3b 17 D3a 16 Q3 15 GND 14 Q2 13 D2b 12 D2a 11 Q1 1 2 4 5 7 8 12 13 15 16 18 19 Q5 D5a D5b D0a D0bD1a D1b D2a D2b D3aD3b D4aD4bD5a D5b VCC D0a Q0 Q1 Q2 Q3 Q4 Q5 D0b Q0 D1a 3 VCC = Pin 20 GND = Pin 10 6 9 11 14 17 D1b 10 SF00449 SF00451 September 14, 1990 2 853-1313 00423 Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804/1804 LOGIC SYMBOL 74F1804 6 7 9 10 12 13 17 18 20 1 3 4 LOGIC DIAGRAM 74F804 D0a Dob D1a D1b 1 2 4 5 7 D2a D2b Q0 Q1 Q2 Q3 Q4 Q5 D3a D3b 2 D4a D4b D5a D5b 8 12 13 15 16 18 19 17 14 11 9 3 QO D0a Dob D1a D1b D2a D2b D3a D3b D4a D4b D5a D5b 6 7 9 10 12 13 17 18 20 1 3 4 2 19 16 14 74F1804 8 QO 6 Q1 11 Q1 D0a D0bD1a D1b D2a D2b D3a D3bD4a D4bD5a D5b Q2 Q2 Q3 Q3 8 11 14 16 19 Q4 Q4 VCC = Pin 5 GND = Pin 15 Q5 Q5 SF00452 VCC = Pin 20 GND = Pin 10 VCC = Pin 5 GND = Pin 15 SF00454 IEC/IEEE SYMBOL 74F1804 6 7 9 10 12 14 13 17 18 20 19 1 3 2 4 16 & 8 FUNCTION TABLE INPUTS OUTPUT Db H X L Q L H H Da H L X 11 NOTES: H = High voltage level L = Low voltage level X = Don't care SF00453 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL VCC VIN IIN VOUT IOUT Tamb Tstg Supply voltage Input voltage Input current Voltage applied to output in high output state Current applied to output in low output state Operating free-air temperature range Storage temperature range PARAMETER RATING -0.5 to +7.0 -0.5 to +7.0 -30 to +5 -0.5 to VCC 96 0 to +70 -65 to +150 UNIT V V mA V mA C C September 14, 1990 3 Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804/1804 RECOMMENDED OPERATING CONDITIONS SYMBOL UNIT VCC VIH VIL IIk IOH IOL Tamb Supply voltage High-level input voltage Low-level input voltage Input clamp current High-level output current Low-level output current Operating free air temperature range 0 PARAMETER MIN 4.5 2.0 0.8 -18 -48 48 +70 LIMITS NOM 5.0 MAX 5.5 TA = -40 to +85C V V V mA mA mA C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS1 MIN VOH High-level output voltage VCC = MIN, VIL = MAX VIH = MIN, IOH = MAX VOL Low-level output voltage VCC = MIN, VIL = MAX VIH = MIN, IOL = MAX VIK II IIH IIL IO ICC Input clamp voltage Input current at maximum input voltage High-level input current Low-level input current Output current3 ICCH ICCL VCC = MIN, II = IIK VCC = MAX, VI = 7.0V VCC = MAX, VI = 2.7V VCC = MAX, VI = 0.5V VCC = MAX VCC = MAX VCC = MAX VIN = GND VIN = 4.5V -60 2.0 15 LIMITS TYP2 MAX V V 0.38 0.38 -0.73 0.55 0.55 -1.2 100 20 -20 -160 3.0 20 V V V A A A mA mA UNIT 10%VCC 5%VCC 10%VCC 5%VCC 2.0 2.0 Supply current (total) mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25C. 3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS. AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25C SYMBOL PARAMETER TEST CONDITION MIN tPLH tPHL Propagation delay Dna, Dnb to Qn Waveform 1 1.0 1.0 VCC = +5.0V CL = 50pF, RL = 500 TYP 2.0 3.0 MAX 4.0 4.5 Tamb = 0C to +70C VCC = +5.0V 10% CL = 50pF, RL = 500 MIN 1.0 1.0 4.0 5.0 1.5 UNIT MAX ns ns tsk(o) Output skew1,2 Waveform 2 1.5 NOTES: 1. [tPN actual - tPM actual] for any output compared to any other output where N and M are either LH or HL. 2. Skew times are valid only under same test conditions (temperature, VCC, loading, etc.,). September 14, 1990 4 Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804/1804 AC WAVEFORMS Dna, Dnb VM tPHL VM tPLH Qn Qn VM tsk(0) Qn VM VM VM SF00005 SF00455 Waveform 1. Propagation delay for inverting outputs NOTE: For all waveforms, VM = 1.5V. Waveform 2. Output skew TEST CIRCUIT AND WAVEFORMS VCC NEGATIVE PULSE VIN PULSE GENERATOR RT D.U.T. VOUT 90% VM 10% tTHL (tf ) CL RL tw VM 10% tTLH (tr ) 0V 90% AMP (V) tTLH (tr ) 90% POSITIVE PULSE VM 10% tw tTHL (tf ) AMP (V) 90% VM 10% 0V Test Circuit for Totem-Pole Outputs DEFINITIONS: RL = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. RT = Termination resistance should be equal to ZOUT of pulse generators. Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate 1MHz tw 500ns tTLH 2.5ns tTHL 2.5ns SF00006 September 14, 1990 5 Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804, 74F1804 DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1 1990 Sep 14 6 Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804, 74F1804 SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 1990 Sep 14 7 Philips Semiconductors Product specification Hex 2-input NAND drivers 74F804, 74F1804 Data sheet status Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Production [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Document order number: Date of release: 10-98 9397-750-05182 Philips Semiconductors yyyy mmm dd 8 |
Price & Availability of N74F804N
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |